Search Documents

By Hongli Wen, Guangkun Shen, Qiong Deng, Shoujian Huang, Min Gan, Xiaohui Fan

"Due to the low iron grade and high sulfur content, pyrite cinder is difficult to be directly used for iron-making. In this paper, technology of magnetic roasting -grinding and magnetic separation -acid leaching was put forward for reclamation of pyrite cinder. For pyrite cinder of TFe53.51%, S2.20 %, studies showed that good magnetic effect can be achieved at roasting temperature 650~7000, reducing atmosphere CO/(CO + C02) 10~20% and roasting time 10~30 minutes. In separation conditions of grinding size -0.045mm accounting for 96.09% and magnetic field intensity of 1240 GS, iron concentrate of TFe64.81 %, S0.18% and iron recovery rate 91.44% was achieved. Acid leaching was studied to strengthen desulfurization. Results showed that high-quality iron ore concentrate of TFe66.3 l %, S0.10% was obtained under the conditions of hydrochloric acid mass fraction of 5%, pulp density of30%, leaching temperature of70? and leaching time of2 hours.IntroductionPyrite cinder is produced as a by-product of sulfuric acid industry [1] Domestic production is more than 12 million tons every year and occupied area is over 10 million square meters [2,3]. The pyrite cinder outdoor not only pollutes air but also damages surrounding surface [4] It after treatment used for iron-making is an ideal reclamation approach for its rich iron which is commonly 40-60% [5]. But pyrite cinder gets low utilization for its low iron grade and high sulfur content in China [6]. Therefore, comprehensive utilization of pyrite cinder has profound significance to environmental protection and the development of domestic iron and steel industry."

Jan 1, 2013

By Farouk T. Awadalla

The presence of humic species in spent Bayer liquor causes many processing problems in the production of aluminum hydroxide. Ozonation of spent Bayer liquor was found to be an effective process to destroy the colored humic species. The kinetics of the decolorization in spent Bayer liquor was found to be slower than in the alkaline humic acid solution containing no alumina. However, the reaction kinetics ware enhanced by heating the solution during ozonation above room temperature. Copper ions which are used as catalyst to enhance the ozonation reaction were found to be ineffective due to the presence of large quantities of aluminum hydroxide in the liquor. Ozonation was a more favorable process than membrane separation as it achieved about 92% separation of color and produced lower amounts of organic material. The treated spent Bayer liquor can be recycled to the upstream process without causing any difficulties and the purity of aluminum hydroxide product would also be improved. A comparison of preliminary cost data indicated that ozonation compares very favorably with membrane separation in this application. Key words: ozonation, Bayer liquor, aluminum hydroxide, humic species, copper ions, membrane separation, purity and economic.

Jan 1, 1994

By Fatbardha Osmani, Skender Osmani

"A system analysis of the resource and environment management (water, energy etc) starts from its definition. Unfortunately, there is not a unique semantics of the mentioned concept. On these circumstances, in this paper the following issues are presented: 1.A short view on the existing concepts of management. 2.A new definition on the concept of management. It is considered as a complex and rational activity on human and natural resources ,environment etc, which starts from a analysis of infrastructure ,technology , etc, mission , alternatives , project etc. and ends to an optimal output. Basing on this definition, the management has two principal components: strategy and policy. The strategy is referred as a blue print program (the same definition as in Game Theory), which contains all the contingency alternatives. , while the policy is referred as a strategy applied into practice. The strategy is the first , while the policy is the second one. The best alternative of a policy is the project, Each strategy has one and only one project. The mentioned definition erases the differences between concept of policy and politics. Each strategy has its alternatives ,the next has its sub strategy and so on, i.e. whatever are going to be the strategy, there are a hierarchy composed by sub strategies up to the simplest strategies applied by a single individual (human beings or robots). The strategy objectives are necessary and sufficient conditions for its realization i.e . the strategy is an optimal activity, in which all resources are integrated and processed . Several strategies could be joined into one( for example the surface water strategies of the Balkan countries) . In this view, the strategy could be globalized into optimal way basing on different criteria’s as social, economic, environmental, their risks and effectiveness etc. etc An example from the water management illustrates the mentioned concepts."

Jan 1, 2008

By V. I. Lakshmanan, R. Roy

"TiO2 is used in paints, plastics, rubber, paper, inks, textiles and other miscellaneous applications. The demand for the pigment grade Ti02 is growing at 3.0%/year on average and this invites the development of innovative and cost effective processes. The current processes are not designed to recycle the reagents and thereby discharge the effluents into the environment, causing an environmental concern.During this study, synthesis of TiO2 from an ilmenite concentrate was investigated using an innovative atmospheric mixed-chloride leach process. The solution purification was carried out using solvent extraction in two stages. In the first stage iron removal was carried out and in the second stage titanium was extracted. The strip solution obtained from the second stage solvent extraction contained the purified titanium and from this stream pigment grade Ti02 was recovered. The barren solution was used for reagent recovery and the regenerated leach liquor was recycled."

Jan 1, 2011

By Fuming Wang, Changrong Li, Dan Wu, Wei Shen, Yaxu Zheng

In order to improve the oxidation resistance of Cr–Mo–V steel for high-speed railway brake discs, a higher Cr was added to the steel. Effect of temperature on the oxidation behavior of brake disc steel with different Cr contents was studied by OM, SEM and XRD. The results show that the oxidation curves at 500 °C obey a linear oxidation law in 0–2 h and 2–20 h, respectively. The oxide layer is thin and the oxidation products are Fe2O3 and Fe3O4. The oxidation curve at 700 °C follows a linear law within 2 h. With the oxidation time extending, the oxidation curves follow a parabolic law and the oxide layer becomes thicker. Moreover, the oxide layer is divided into two layers. The outer oxide layer is loose and is mainly Fe2O3, while the inner layer is denser and consists of FeO and FeCr2O4. The oxide layer thickness reduces and the oxidation resistance of the steel is improved with Cr content is increased.

Mar 1, 2018

By Pertti Koukkari

The novel Jarogain process combines treatment of the jarosite residue of zinc manufacturing and processing of arc furnace dust from steelmaking to a holistic recovery technology. The new hydrometallurgical approach is targeted to recover the major constituents (Fe, Zn, Pb) as well as valuable components such as Ag, Au, In and Ga from the jarosite-dust mixture as reusable concentrates. The fractionation process proposed by VTT and Aalto University takes advantage of jarosite being readily fine powder and directly available for wet chemical processing. Jarogain process provides an energy efficient opportunity for jarosite utilization as value added products. The experimental proof-of-concept of key stages of the process will be outlined with a comparison of available pyrometallurgical treatments of jarosite waste. The techno-economical assessment is based on estimated investment and variable production cost using the discounted cash flow (DCF) analysis.

By Henry L. Ehrlich

This survey compares bioleaching and biobeneficiation by autotrophic bacteria with that by heterotrophic bacteria and fungi Some physiological principles are reviewed. Advantages and disadvantages of autotrophic and heterotrophic leaching are discussed. Principles of anaerobic leaching by autotrophs and heterotrophs are introduced. and the advantages? over aerobic heterotrophic leaching are discussed. Examples of useful organisms in the autotrophic and heterotrophic categories are cited.

Jan 1, 1991

By Mingming Zhang, Ramana G. Reddy

A 3-D mathematical model was developed for the batch reactor of low temperature aluminum electrowinning using ionic liquid electrolytes. This model describes the deposition process by incorporating the mass transport of participating ionic species, homogeneous chemical reactions within the diffusion layer, and the associated electrochemical kinetics. Processing parameters, current and potential distribution, species concentration, fluid flow distribution, and electrode spacing were evaluated for the optimal reactor performance. The results indicated that the electrode spacing significantly affects the electrolyte fluid flow and current density distribution. The parallel electrode configuration (in line with electrolyte inlet) improved the convection and resulted in uniform current density distribution and electrolyte fluid flow. However, for this electrode configuration, electroactive species distribution was most favorable between the electrodes. Perpendicular configuration of electrodes resulted in a more non-uniform fluid flow within electrolyte domain, and it has a potential to cause non-uniform deposits. Aluminum electrowinning experiments were conducted using batch reactor at 80 °C, electrolyte flow rate of 5–20 ml/min, and applied cell voltage of 3–3.5 V. Good agreement was obtained between the model and the batch aluminum electrowinning experimental results.

Mar 1, 2017

By Q. Cao, A. Pitts, L. Nastac

Accurate prediction of the desulfurization behavior of steel is of great importance for process control during ladle metallurgical furnace (LMF) steel refining. A CFD model capable of simulating multiphase flow with bulk and free surface turbulence phenomena and desulfurization behavior in the gas-stirred ladle has been developed. The fluid flow behavior shows that slag and metal try to entrap each other, forming a two-phase mixing zone. The resulting substantial contact area between the two phases will provide very favorable kinetic conditions for chemical reactions. For reaction kinetics model, the reactions at the metal/slag bath interface as well as the entrapped droplet surface are included. Predicted results show that the sulfur content changing with time in the ladle agrees well with the industrial-scale experimental measurements.

Mar 1, 2017

By Derk G. E. Kerfoot

The extractive metallurgy of nickel and cobalt has proved to be a particularly fruitful area for innovation in hydrometallurgy and electrometallurgy ever since the development of the Hybinette process for nickel in the early 1900's. In current practice, nickel concentrates are generally smelted to high grade mattes which are then refined to metal by a combination of hydrometallurgy and electrometallurgy, although low grade copper-nickel concentrates are refined directly by the ammonia pressure leach process. Matte refining processes in commercial operation include the direct electrolysis of matte, the ammonia pressure leach, sulphuric acid leaching using air or oxygen at elevated pressure, or at ambient pressure, and chlorine or chloride leaching. Refined nickel is recovered either as electrolytic cathode, or as metal powder by hydrogen, reduction. Hydrometallurgy has also found application in the treatment of nickel laterite ores, both in the reduction roast ammonia-ammonium carbonate leach process, pioneered by Caron and in the Moa Bay acid leach process. Cobalt is recovered as a co-product of copper in central Africa, and as a byproduct of hydrometallurgical nickel refining elsewhere. In the African plants, the copper-cobalt concentrates are roasted and leached in sulphuric acid solution, and copper and cobalt are recovered separately from the leach solution by direct electrowinning. A variety of hydrometallurgical techniques are used for the separation of cobalt from nickel, including selective precipitation and crystallization, solvent extraction, and ion exchange. Like nickel, refined cobalt is recovered either as electrolytic cathode or as metal powder by hydrogen reduction.

Jan 1, 1988

By C. E. Hunt

Since the turn of the century, copper-nickel sulphide ores have been processed at the Sudbury, Ontario operations of INCO Limited, currently the largest integrated mining, milling, smelting and refining complex in the free world. Through the years operational, ecomomic, social and legislative changes have dictated the need for research and development directed at mitigating the impact of existing operations on the surrounding natural environment and also the reclamation of areas affected by earlier mining activities. Approximately one hundred years of mining history and the current annual processing of some 12 million tons of ore presents significant challenges with respect to waste disposal, liquid effluent treatment and land reclamation, particularly in light of rapidly evolving environmental regulations' and controls within the Province of Ontario.

Jan 1, 1992

By Philip L. Sibrell

A new process utilizing pulsed fluidized limestone beds was tested for the remediation of acid mine drainage at the Friendship Hill National Historic Site, in southwestern Pennsylvania. A 230 liter-per-minute treatment system was constructed and operated over a fourteen-month period from June 2000 through September 2001. Over this period of time, 50,000 metric tons of limestone were used to treat 50 million liters of water. The influent water pH was 2.5 and acidity was 1000 mg/L as CaCO3. Despite the high potential for armoring at the site, effluent pH during normal plant operation ranged from 5.7 to 7.8 and averaged 6.8. As a result of the high influent acidity, sufficient CO2 was generated and recycled to provide a net alkaline discharge with about 50 mg/L as CaCO3 alkalinity. Additions of commercial CO2 increased effluent alkalinity to as high as 300 mg/L, and could be a useful process management tool for transient high flows or acidities. Metal removal rates were 95% for aluminum (60 mg/L in influent), 50 to 90% for iron (Fe), depending on the ratio of ferrous to ferric iron, which varied seasonally (200 mg/L in influent), and <10% of manganese (Mn) (10 mg/L in influent). Ferrous iron and Mn removal was incomplete because of the high pH required for precipitation of these species. Iron removal could be improved by increased aeration following neutralization, and Mn removal could be effected by a post treatment passive settling/oxidation pond. Metal hydroxide sludges were settled in settling tanks, and then hauled from the site for aesthetic purposes. Over 450 metric tons of sludge were removed from the water over the life of the project. The dried sludge was tested by the Toxicity Characteristics Leaching Protocol (TCLP) and was found to be non-hazardous. Treatment costs were $43,000 per year and $1.08 per m3, but could be decreased to $22,000 and $0.51 per m3 by decreasing labor use and by on-site sludge handling. These results confirm the utility of the new process in treatment of acid impaired waters that were previously not amenable to low cost limestone treatment.

Jan 1, 2003

By Juan Hernández Ávila

This work studies the Molybdenum effect on the microestructure, mechanical properties of an as-cast ductile iron. For this study five ductile irons with different amounts of Molybdenum each were made in an induction furnace. In this material nodule count and nodularity is affected by the Molybdenum additions; The iron´s matrix, nodules and the phase were analyzed using scanning electron microscopy detecting Molybdenum only in the matrix. Mechanical properties such as hardness, microhardness, tensile strength and yield strength show increments as the Molybdenum amount is increased. In the same way, ferrite and pearlite phases display a variation in their percentage as the contents of the alloy element increase. This element has a marked influence on the pearlite interlaminar spacing. From the obtained results we conclude that Molybdenum in these quantities dissolves in solid ferrite solution during the solidification process, improving the material´s mechanical properties.

Jan 1, 2009

By Feng Gao

A general unsteady- state model, based on a cracked substrate, has been developed to account for reaction and diffusion within porous substrate during oxidation of Carbon Fiber Reinforced Carbon matrix (CIC) composites. The effects of several parameters, such as diffusion and reaction rate ratio, oxygen concentration, and composite density, on oxidation process are explored. Also, theoretical results for a set of parameter values of the CIC composites are compared with experimental data. It shows that the model predicted values agreed well with the experimental data in weight loss. Based on this model, quantitative predictions of oxidation of a composite with cracked substrate can be made.

Jan 1, 1993

By Garth James

Bacterial consortia capable of degrading cyanide and metal-cyanide complexes were obtained from gold mine process waters using enrichment cultures. The cultures contained either cyanide, tetracyanonickelate, or ferrocyanide as a sole nitrogen source. Several bacteria were isolated from the consortia, but none of these organisms were capable of degrading cyanide or cyanide-metal complexes at rates equivalent to those of the intact consortia. The consortium from the cyanide enrichment was capable of completely degrading cyanide from an initial concentration of over 100 ppm in less than one day, when cultured using a fed-batch method. Tetracyanonickelate and ferrocyanide were degraded more slowly. Overall, these results demonstrate that bacteria capable of degrading cyanide and cyanide-metal complexes can be isolated from mine process solutions and are capable of significantly reducing cyanide concentrations under appropriate conditions.

Jan 1, 1998

By Juliana Augusto Molari, Deborah Dibbern Brunelli, Leonardo G. de Andrade e Silva, Patricia N. S. Poveda

There are several additives aimed on improving the processing characteristics as well as mechanical properties of the plastic materials. Being polypropylene is one of the main polymers used in the plastic processing industry due to its easy processability and application versatility, was chosen as the base resin for this study. Additives can aid the processing of polypropylene, either by promoting a better slip between the chains (lubricants), or by contributing to nucleation and crystallinity (nucleating). In this study, the raw materials copolymer polypropylene, lubricant (internal and external action), organic nucleating agent (metallic salt) and inorganic nucleating agent (metallic oxide) were considered. Mechanical tensile tests, Charpy impact and spiral flow to verify melt index were performed to characterize the samples with additives and standard (copolymer polypropylene). The interference of these additives with polymeric matrix was observed.

Mar 1, 2018

By John E. Litz

The Denver Process is a chemical/metallurgical process for treating radioactive or mixed wastes by extraction and concentration of the radioactive and/or hazardous component(s). The process was developed at bench scale, evaluated at pilot scale, and will be implemented at full scale to remediate a low-level radioactive sludge. Six unit operations comprise the process: feed handling, leaching, solvent extraction, electrodeposition, precipitation, and tailing preparation. Unit operation design may be modified to tailor the process for varying feed stock composition. Radioactive or mixed waste is reacted with aggressive reagents in an aqueous phase, solubilizing targeted components. These components are then selectively extracted and concentrated in subsequent steps. Waste solids and solution exit the process as non-hazardous non¬radioactive waste. Dehydration of aqueous waste by submerged combustion eliminates aqueous discharge.

Jan 1, 1994

By Jim Sarvinis, Mark Berkley, David Clarry, Jason Berzansky

"Technologies developed to sequester CO2 or use CO2 for enhanced fossil fuel recovery are currently being utilized across the globe. Taxation regimes and CO2 credit trading are becoming drivers for a number of projects. Some mining companies have also identified ancillary opportunity to sequester CO2 in their by-products; recent work in the alumina industry is a prime example. In addition to process plant emissions, mining companies are becoming increasingly aware of their overall carbon footprint, including CO2 generated during the production of utility power. New power plant designs, in various stages of development, include CO2 separation and sequestration techniques. This paper summarizes the state-of-the-art for these technologies; including integrated gasification combined cycle (IGCC) power plants. A concept to use the gasification products as reductant in metallurgical processes is also described. The relevance of technology from power plant designs with post-combustion capture to the processing of off-gas generated in metallurgical facilities is also reviewed.IntroductionGlobalization and international economic growth have led to an increase in energy demand worldwide, and a corresponding increase in greenhouse gas (GHG) emissions. In 2005, 81% of global energy supply came from fossil fuels [1]; and while alternative energy technologies are emerging, it will require many decades to curb society’s fossil fuel dependence. Given the global concern of climate change and its scientific relationship with anthropogenic carbon dioxide (CO2), there is at present great interest in the development of techniques to reduce emissions of CO2. While most of these efforts are related to power generation and energy efficiency, the development of technologies for CO2 capture may offer opportunities in reducing emissions from industrial processes."

Jan 1, 2008

By A. Tsubouchi, F. Noguchi, T. Takasu

"A high current density operation is desired to improve the productivity in copper electrorefining. However, a lot of problems still remain such as passivation at anode, dendritic deposition at cathode and impurity behavior during the electro refining.Effects of the current densitY on the morphology of copper deposition on the cathode, and passivation at the anode were investigated at various fluid velocity of electrolyte in the present study.Although a granular appearance of the copper deposition was obtained with increasing high current density, it was depressed by an increase of the fluid velocity of the electrolyte. A uniform deposition on the cathode was also observed when the fluid velocity of the electrolyte become higher. It was ascertained that passivation at the anode was suppressed by circulating electrolyte during electrolysis. INTRODUCTIONIt is desirable to operate at high current density in copper electrorefining in order to improve plant productivity without enlarging the size of electrodes(1). However, there are many problems in copper electrorefining at high current density with the usual commercial practice, for example, anode passivation, dendritic deposition and an increase of impurities in the cathode.In general, it is effective to agitate the electrolyte in order to suppress these problems(2). Smith et a1.(3) have performed electro refining experiments at various current densities in the range of 8 to 32 Aldm2 and at electrolyte fluid velocities in the range of 40 to 120 mlmin, and they obtained well consolidated, void free copper even at high current density in a high electrolyte velocity. However, they did not discuss the recovery ratio and the passivation behaviour at the anode. Walsh et a1.(4)(5)(6) experimented with the rotating cylinder electrode, and ascertained that electrolysis can be carried out at high current densities under the condition of pure electrolyte.With regards to anode passivation, there are several papers by previous workers(7)(8). Our group ascertained the process of producing anode slime during electrolysis(9). However, these experiments were carried out without forced circulation of electrolyte. Therefore, in the present study, to solve these problems, we electrolyzed at current densities in the range of 4 to 50 Aldm2 with circulating electrolyte in the range of 0 to 48 mlrnin. The effect of electrolyte fluid velocity on the surface morphology of deposited copper at cathode and passivation at anode were investigated when electrolysis were carried out with circulating electrolyte at high fluid velocity and at high current density."

Jan 1, 1997

By Duclerc Fernandes Parra, Vijaya Kumar Rangari, Washington Luiz Oliani, Ademar Benevolo Lugao, Nilton Lincopan

Due to its versatility and low cost, polypropylene (PP) is one of the most widely used polymers in the world, consequently in research and development of new products. The polypropylene modified was prepared by gamma irradiation in acetylene at 12.5 kGy dose, technical polymer also known as high-melt-strength-polypropylene (HMSPP). It was mixed with montmorillonite (MMT) clay and silver nanoparticles (AgNPs) for bactericide activity. HMS-Polypropylene-clay-silver nanocomposites were manufactured using twin-screw extruders. Those materials were prepared by a melt mixing process via twin screw extrusion with a wide range of processing conditions. The polypropylene nanocomposites (PPNC) surfaces were exposed to gamma-radiation (60Co) source in presence of nitrogen as inert atmosphere at 1; 3; 5; 10; 20 and 50 kGy doses for modified the surfaces in order to enhance biocide activity. The samples surfaces were characterized by Differential Scanning Calorimetry (DSC), X-ray Diffraction (XRD), Thermogravimetric Analysis (TGA), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDX) and evaluated by determination of bactericide effects. The results indicate the formation of structures predominantly intercalated of HMSPP nanocomposite. Contact tests for antibacterial activity of the hybrid polymer were applied against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) bacteria. The irradiations on the samples surfaces were insufficient to promote activity on contact biocide tests.

Mar 1, 2018