Search Documents

By Xuan Cheng

The electrochemistry of sulfide mineral flotation is reviewed with particular emphasis on galvanic interaction among minerals and grinding media, and its relevance to flotation of complex sulfide ores is discussed. Surface alteration due to galvanic interactions among chalcopyrite, pyrrhotite and mild steel is analyzed in terms of voltammetric and chronoamperometric studies on individual minerals and through galvanic current measurements in 2- and 3- electrode combinations. The results are related to laboratory flotation behaviors of chalcopyrite-pyrrhotite mixtures simulating copper-nickel bearing Duluth gabbro.

Jan 1, 1993

By Richard D. Hagni

Although the economically important uranium minerals are difficult to recognize under the ore microscope, they can be identified by a combination of qualitative and quantitative techniques. Useful quantitative techniques include indentation hardness, percent reflectance, spectral reflectance curves, and color coordinates. The latter two properties are especially distinctive for the primary urahlferous minerals uraninite, coffinite, brannerlte, and davidite. Together with the quantitative properties of indentation hardness and reflectance, the character and color of internal reflections are distinctive for many of the secondary uranium minerals. Ore microscopic techniques also provide an excellent means for determining the intergrowths of these minerals with other ore and gangue minerals. Such intergrowths are important to an understanding of the genesis of uranium deposits, and they may be important to uranium extractions.

Jan 1, 1981

By Federico Chavez

The process for recovering lead from battery residues used in several Mexican Plants include lead blast furnace and rotary furnaces. The formers are basically fed with recycled batteries together with the necessary additives to produce metallic lead. One of the by-products generated in the blast furnace is a dust mainly formed by lead sulfide. The rotary furnace is used to recover lead .from lead batteries, dross from the refining-alloying process and the leady fines produced in the blast furnace. This paper describes thennodynamic analysis made to the rotary furnace process to understand the effect that each component of the system has upon the lead recovery. In order to enhance the process, the influence of iron chips composition and excess coke on slag viscosity is discussed. A computer optimization program . has been developed to design the furnace charge based on material and energy balances, .together with the thennodynamic equilibrium calculation.

Jan 1, 1995

By A. Deneys

An experimental technique has been devised for studying the reaction kinetics of the reaction: ZnO + 2Fe0 = Zn(g) + Fe203, by which zinc evolution can occur from a molten slag bath in the absence of a carbonaceous reductant. When studying the reaction kinetics by heating from room temperature, solid state reactions and poorly defined melting points may obscure the starting point of the reaction. In order to eliminate this problem, an experimental technique was devised whereby two molten slags could be melted independently, and then mixed, to provide a well defined starting point from which to begin taking measurements. Two crucibles were mounted in a vertical reaction cylinder. The upper, mild steel, crucible had a bottom pouring plug which was sealed by a steel stopper rod. A fayalite mixture was contained in this crucible. The lower crucible contained an A12O3-CaO-SiO2-ZnO solution. Once the two slags had been melted, the steel stopper rod was removed from the upper crucible. The upper, reduced slag (fayalite in equilibrium with the upper steel crucible), drained into the lower crucible where the two slags were mixed by submerged argon stirring. Dip samples were taken to measure the zinc content of the final mixture as a function of time. The experimental procedure will be described, as well as results of experiments which were conducted on synthetic slags. The system investigated was similar to the lead blast furnace slag which is produced by the primary lead smelters of Missouri, USA.

Jan 1, 1997

By R. A. Roberti

Most copper refineries use conventional wheel systems to cast anodes. over a period of time the copper moulds that are used become warped and cracks develop. To control mould warpage, the mould's are either rejected after a certain warpage is reached, or the shape is restored by mechanical means. The cracks, unless they are very severe, are repaired by a peening process. Even with regular maintenance to control warpage and cracks, the moulds have a limited useful life. If warpage and cracks are not controlled, anode quality deteriorates and tankhouse operations are seriously affected. -An intensive study was initiated to develop means of controlling mould warpage which culminated in the d?evelopment of technology to control mould warpage to within ±1. 5 mm, and at the same time effectively contr0l: cracking and significantly increase the mould life-. The warpage control has been achieved by using a unique mould design. Mould cavities are present on both sides of the mould and periodic inverting controls the wa-rpage in the cavities. The mould casting procedure has been developed and all production wheels have been converted to the new mould design. The performance characteristics of these moulds will be detailed. 21

Jan 1, 1987

By Jonkion M. Font

Due to the known disadvantages of the use of iron silicate slag in the nickel converting stage, i.e., high metal losses, high magnetite content, and low fixation of impurities in the slag, the development of the new proposed "ferrous calcium silicate slag" for smelting and converting processes of nickel is very promising. Hence, considering the successful experimental results of using CaO base slag for the nickel smelting process, a study based on a detailed comparison for the phase equilibrium, and the minor elements distribution between the Ni3S2-FeS matte with either FeOx-CaO or FeOX-Si02 base slag was investigated. The main results are summarized as: no difference in the nickel losses between both slags was found at high nickel content in the matte, and the fractional distribution analysis for arsenic and antimony pointed out their preferential fixation in the calcium ferrite slag rather than in the iron silicate slag. Considering the energy and pollution issues, the technical feasibility of using calcium ferrite slag in a converting process of the Bessemer matte will have a prominent future for the nickel industry.

Jan 1, 2003

By Philip Arthur

The ISASMELT process is making a significant contribution to the global metals industry. ISASMELT furnaces are now operating successfully in eight different countries and treating approximately 3 million tonnes of concentrates and secondary materials per year. The process is currently used in both lead and copper smelting. The most recently commissioned plants were in Germany and China, one for treating scrap copper and the other treating low-grade copper concentrates. The Copper ISASMEL T furnace ("CIF") at Mount Isa Mines Limited (UMIM") has continued to set new operational records, with throughput of more than I million tonnes of concentrate per year and very low operating costs. This paper summarises the latest operational data from the Mount Isa Copper ISASMEL T plant and outlines the successful approach to industrial R&D taken by MIM in the development of the ISASMEL T process.

Jan 1, 2003

By David R. Brosnahan

Increased Cu grades due to chalcopyrite-rich ore from The Doe Run Company's new Casteel Mine prompted a program to increase Cu recovery. Preliminary tests indicated that prohibitive quantities of FeS2 float with chalcopyrite. Point counting of mill stream samples showed that locking was not a major problem, although grinding to finer particle size enhanced the floatability of both chalcopyrite and marcasite. Backscattered electron images and microprobe analyses of FeSz minerals revealed the presence of Pb which appears to occur as solid solution in marcasite, and as a sub-micron particulate Pb phase in pyrite.

Jan 1, 1987

By Beatryz C. Mendes, Igor K. R. Andrade, Roseli O. G. Martins, Gustavo H. Nalon, Rita de C. S. S. Alvarenga, Leonardo G. Pedroti, Carol F. R. Santos, Marcelo A. Alves

This work presents an experimental investigation of the influence of concrete blocks and mortar’s compressive strength on the flexural bond strength, normal to the bed joints, of concrete structural masonry. Third-point beam tests were performed on concrete prisms, considering two different kinds of concrete blocks (compressive strength of 5.9 and 8.2 MPa) and six different cement-lime mortar compositions (compressive strength around 30, 70, and 120% of the blocks’ net area compressive strength). Units’ absorption and mortar’s initial flow and water retentivity were not varied, but remained within the suitable range for use in structural masonry. For both types of concrete blocks, it was observed an increase on the prism’s flexural bond strength with the increase of the mortars’ compressive strength. A lower mortar’s water-cement ratio led to higher bond strength. When fixing the ratio between mortar’s and concrete block’s compressive strength, it was noticed that the increase on the blocks’ strength contributed to a slight increase on the masonry’s flexural bond strength, except when using high strength mortar, in which the increase was significantly greater.

Mar 1, 2018

By Susan Fredholm, Randolph Kirchain, Jeremy Gregory

"Jurisdictions across the world have struggled to create and finance systems that can effectively collect and process electronics waste (e-waste). Many different system architectures have been proposed and implemented, but it is difficult for policy-makers and system architects to compare the costs and benefits of different systems, particularly when the systems operate in different contexts. This paper presents a systematic methodology that seeks to address this challenge and uses data from several existing electronics recycling systems across the world to illustrate its implementation. The methodology characterizes three main system characteristics: architecture (e.g., financing and collection methods), context (e.g., jurisdiction population, density, and wages), and performance, both economic and materials collection. A comparison of systems in Europe and North America with different system architectures and contexts illuminates the importance of using the methodology to discern the extent to which architecture and context drive system performance.IntroductionElectronic waste (e-waste) recycling offers several environmental benefits when processing is done responsibly. The controversy around e-waste recycling systems rarely debates such benefits; rather, it focuses on the characteristics of an effective system and whether benefits outweigh costs. Historically, the costs of recycling most electronics have outweighed the value of the scrap recovered. Thus, in the absence of legislation, e-waste recycling systems have been limited to private recycling of high-value waste with minimal consumer participation. E-waste recycling systems now exist in many locations worldwide including Asia, the European Union, Canada and the United States and the amount of related legislation continues to increase. Numerous approaches have been proposed including landfill bans, extended producer responsibility (EPR) and consumer advance recovery fee (ARF) funded recycling systems."

Jan 1, 2008

By P. K. N. Raghavan

This paper identifies potential technologies for Carbon dioxide abatement from the mining and metal industry with special reference to the Aluminium industry. Mine reclamation could contribute to this effort to successfully reach the greenhouse gas (GHG) emissions reduction commitments for a nation. An overview of GHG production by the mining and metal industry together with a review of principles used to set the context in which specific options for GHG reduction are described. Options for GHG reduction in the mining and metal industry include reforestation, Addition of soil amendments or neutralizing agents, CO2 capture and storage, initiatives towards energy reduction, waste heat recovery and alternative energy use. An analysis and quantification of the potential GHG reduction of potential carbon sinks and sequestration options for the mining and metal industry are provided. Cost estimates for different options are provided. The paper also identifies sources that could fund research regarding GHG reduction options. The paper concludes with recommendations.

Jan 1, 2011

By David T. Hobbs

Large quantities of highly alkaline, radioactive, liquid wastes are stored in underground tanks throughout the Department of Energy complex. These wastes will be pretreated to separate radionuclides and the remaining decontaminated liquid wastes incorporated into solid waste forms for permanent disposal. Significant savings in disposal costs could result by recovering .the sodium as sodium hydroxide for reuse or disposal as nonradioactive waste. Recent testing demonstrated an electrochemical separation process for the recovery of sodium hydroxide from alkaline waste solutions; The separation process uses ion-selective membranes to separate sodium from the bulk of the waste constituents under an applied electrical field. The sodium is recovered as a 10-15 wt % solution of sodium hydroxide. Results of bench-sc3Ie and pilot-scale tests with simulated and radioactive waste solutions are presented.

Jan 1, 1999

By Qinghai Pang

"With the increasing proportion of bituminous coal in blend coal, the safety of blend coal during pulverization and transportation is gradually being paid more and more attention. Therefore, the explosivity of bituminous pulverized coal (PC) with different volatile content from 25 to 38% was studied by measuring the combustion flame length after its injection into a glass pipe with the heat source installed in the center. The results indicated that high volatile content bituminous PC is apt to have higher explosivity. By blending different bituminous PC with 10% anthracite, the explosivity of bituminous PC showed a positive correlation with the proportion –OH radical. However, different bituminous PC seemed to have the same explosivity when the addition of anthracite increased to 20%. With the further increasing proportion of anthracite to 30%, the explosivity of bituminous PC with high –OH proportion became negligible while a weak explosivity of high –CH3 proportion bituminous PC still remained.IntroductionWith the increasing iron ore prices and decreasing steel prices, it has become critical for iron and steel enterprises to control the cost in ironmaking and steelmaking process. Blast furnaces (BF) are the main consumer in ironmaking process, which occupies 70% fuel consumption of total steelmaking process [1]. In this circumstance, any means necessary is taken by BF operators to lower the cost of iron in production. Coke and iron ore are the main expense in this process, who takes up a very high proportion in total cost. Pulverized coal injection (PCI) is the most efficient way to reduce coke ratio, which replace coke with relatively cheaper PC.At present, most of BF is injected with blend coal in the consideration of decent combustion property and quantity of heat. Simultaneously, bituminite and anthracite blending is an effective method to obtain blend coals with required composition and performance, such as volatile and ash content, etc. Nevertheless, a very huge gap was found between the price of bituminous coal and anthracite in some regions of China, in which the price of bituminite can be just 70% of the price of anthracite. Thus, iron enterprises in these regions attempt to possibly amplify the proportion of bituminite in blend coal. Increasing proportion of bituminite results in higher volatile content in blend coal, by which the safety of blend coal during pulverization or transportation was deteriorated.Relatively, coals with higher volatile content usually possess stronger explosivity, which means that volatile and explosivity may related to some extent. However, the relationship between volatile and explosivity is not of certainty for some PC with high volatile content around 40% was found to be inexplosive in comparison to the coals with lower volatile content. With the increasing proportion of bituminous coal in blend coal, investigations on the factors of PC explosivity have become more and more important. Therefore, bituminous coals with different volatile content were selected. The explosivity of blend coal and its relationship between volatile content and functionality was investigated in this research."

Jan 1, 2014

By Ari I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(C03l2Fj. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in flUorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By Frederick T. Wallenberger

"Laser assisted chemical vapor deposition (LCVD) is a new containerless fiber process whereby growth of small diameter fibers or microstructures (microsprings, microsolenoids) occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber inside the reaction chamber. Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Continuous fibers and multifilament yams are possible. The use -of high reaction chamber pressures (1-10 bar) and a small wavelength Nd-YAG laser made it possible to fabricate small diameter fibers at growth rates >1 mm/s. This paper describes the synthesis of single crystal, polycrystalline and amorphous fibers by LCVD, and provides a comprehensive analysis of phase transformations occurring during their fabrication.IntroductionLaser assisted chemical vapor deposition (LCVD) is a new containerless fiber process [1-10] whereby growth of small diameter fibers or microstructures occurs directly from the vapor phase. The laser beam has a focal point adjusted to coincide with the tip of the growing fiber in the reaction chamber (Figure 1). The diameter of the growing fiber corresponds to that of the laser focus. Depending primarily on the laser energy (Le., the temperature at the growing fiber tip), it is possible to obtain single crystal, poly crystalline or amorphous fibers by this method.Since the growing fiber is not in contact with reactor walls or foreign materials, it is chemically pure, and suitable for optical uses and uses requiring high structural uniformity. Laser assisted CVD is a potentially continuous process; continuous fibers and multifilament yams are possible."

Jan 1, 1994

By I. Gaballah

Decontamination of synthetic solutions of PbC12 containing 10, 100 and 1000 ppm of lead, using chemically treated barks had been studied. The percentage of !cad cations' removal from solutions depends upon the pH and the initial concentration. About 99 % of the initial lead content can be removed at pH of about 3.5, 5.5 and 6.5 for initial concentrations of 10, 100 and 1000 ppm respectively. The maximum retention capacity of the treated bark is about 83 mg of lead per gram of modified bark. Bark loaded with lead had been analyzed by Infra Red spectroscopy. It seems that lead reacts with hydroxyl groups of the phenolic constituents of the bark. On the other hand, the removal of a lead cation by the bark leads to the release of two H+. This seems to show that the removal of lead could be interpreted as an ion exchange with hydrogen belonging to the hydroxyl groups of the modified bark.

Jan 1, 1994

By Onder Guney, Erdem Demirkesenm

"In this study, the crystallization behavior and thermal expansion coefficient of a lithium disilicate (LS2) based glass-ceramic derived from SiO2-Li02-AhO3-K2O-ZrO2 system was investigated by using x-ray diffraction (XRD), high temperature x-ray diffraction (HTXRD), differential thermal analysis (DTA) and dilatometer techniques. Analytical reagent grade chemicals were chosen as raw materials for preparing glass batches. Nucleation and crystal growth heat treatments were planned according to DTA results. The amounts of the amorphous and crystalline phases developed during the heat treatments were determined by quantitative XRD. XRD results of crystallized samples showed simultaneous formation of lithium silicate (LS) and quartz in the early stage of the crystallization followed by formation of lithium disilicate (LS2) at higher temperatures. The thermal expansion coefficients of glassceramics were also measured depending on the applied heat treatments.IntroductionSignificant developments occurred in all ceramic materials provide the fabrication of high quality dental implants [1]. Glass ceramic based dental restorations like dental inlays, crowns, bridges and veneers are becoming increasingly popular with their reliable and durable performance [2,3]. In addition to their advanced functional properties, glass ceramic implants especially lithium disilicate glass ceramics also face the esthetics expectations of patients and dentists and in this way they are starting to take the place of metal based restorations today [1,3,4,5]. Lithium disilicate glass-ceramics derived from multicomponent glass systems have some superior mechanical and optical properties comparable to natural teeth [ 6]. In restorative dentistry, mechanical characteristics of biomaterials play very crucial role in order to resist the masticatory forces occurred during biting and chewing [7] According to three point bending test results of Roland, flexural strength of the lithium disilicate glass-ceramics were 400±40 MPa and their fracture toughness (K1c) are approximately 3,3 MPa m112 [2,6]. In addition to high mechanical strength, aesthetic appearance is another important prerequisite as material for dental restorative applications. Translucency and light transmission of the LS2 glass ceramics mimic enamel. Moreover, opacity of the material can also be adjusted depending on the restoration types [2,6, 7]. These superior properties of the LS2 glass ceramics are directly related with chemical composition of the base glasses and controlled crystallization heat treatments [ 4, 7]. The aim of the present work is to determine the effect of heat treatment schedules on the crystallization behavior and thermal expansion of the LS2 glass-ceramics."

Jan 1, 2011

By Robert D. Pehlke

"Current continuous casting processes are going through a rapid evolution of advances and new developments. At the same time, intense efforts are being directed to the development of radical new technologies such as continuous casting of thin slabs and strip steel.Traditionally, the casting processes for steel have been anticipated by the development and implementation of processes in the non-ferrous industry. This trend is reviewed and what it may portend for steel is described.IntroductionThe continuous casting of steel has been a widely adopted process in the production of steel. The concepts for this processing go back into the early and mid 1800's; however, commerical development was delayed for a variety of reasons until the mid twentieth century.Beginning in the early 1960's, adoption of continuous casting was initiated and continues at this point in time to be accelerated. In Japan, more than 90% of the steel produced is continuously cast (1). More than 50% of the steel produced in the United States is continuously cast and this fraction continues to rise (2). Numerous examples can be cited of installations costing well over $200,000,000 which have provided a payoff in less than a year and a half. As this process has continued to be applied and its technology to increase, computer control systems have been installed. In particular, in the larger plants producing slabs, sophisticated computer systems involving the integration and networking of mini-computers, micro-computers, and mainframe including back-up systems at all levels are being utilized. Pehlke (3), and Harabuchi and Pehlke (4) have described the structure of these systems."

Jan 1, 1988

By C. J. Newman

In January 1999, a redesign of the Kennecott Flash Converting furnace settler was initiated to enhance furnace integrity and extend furnace life. This furnace uses Kennecott-Outokumpu Flash Converting technology to produce copper directly from copper matte. A detailed assessment was made of all technology available around the world before making a decision on the design features to be incorporated in the new design. The new design includes the following: redesign of all sidewall cooling elements to include the latest cooling element technology; redesign of the furnace hearth to include a stadium hearth at the reaction shaft end of the furnace; redesign of the furnace hearth to include a stepped hearth design adjacent to the furnace sidewalls; addition of flat settler roof cooling elements .around the reaction shaft; replacement of reaction shaft transition elements with an improved design and improvements to the furnace cooling element monitoring systems. The Flash Converting furnace was shut down on a planned basis in July 2001 to implement these improvements after 29 months of operation, converting more than 1,000,000 tonnes of matte. During the 30 day shut down, the improvements were successfully completed, with furnace start up in August 2001

Jan 1, 2002

By Ho-Sang Sohn

The kinetic study on desulfurization of copper matte by gas bubbling was designed under the presumptions of lower FeO activity and of no slag formation, Copper matte with 59% Cu and 22.6% S in weight was oxidized at 1523K by bubbling of Ar + O2 gas through a submerged nozzle. The effects of oxygen partial pressure and flow rate of gas on the oxidation rate of matte were discussed. The desulfurization rate and the evolution rate of SO2 gas of copper matte were significantly influenced by the oxygen partial pressure, but the dependence on gas flow rate was rather complicated. The desulfurization rate and evolution rate of SO2 gas of copper matte were described by the mass transfer rate through the gas film around the rising gas bubbles. Thermodynamic correlation equations between the partial pressure of gaseous species and matte composition were incorporated to the kinetic calculation, The present model shows that the reaction path starts to transiently cross over an isobar line of PSO2 to asymptotically approach to the particular isobar line drawn in a matte composition plane of %S and %O.

Jan 1, 2003