Search Documents

By A. R. G. Azevedo, G. C. Xavier

"This work has for objective to identify the soil of the neighborhood Codin located in a lacking area of the urban nucleus of the district of Campos dos Goytacazes - RJ, after the identification the best line was determined for the production of soil-cement blocks. In this area it happens habitational deficit and precarious constructions are also verified. The use of soil cement blocks is considered a cheaper constructive method than the conventional (ceramic block or of concrete), because one of the components of the raw material is abundant (the soil) and the constructions can be erect with certain easiness for collective effort regime. Samples of soil of this area were collected for they be characterized with relationship to the physical and chemical characteristics, with I aid of GPS the community's location it was registered. Identified the soil type, the work began the study of lines they to make possible your use in an economical and safe way. For that were made drained blocks in the format 19,5x10x5 cm, with lines containing the addition of 5% and 10% of cement in volume, and as parameter of quality the absorption of water and the resistance to the compression were measured, following the Norms of ABNT.IntroductionWe know that the use of the soil by the humanity come from the antiquity. And ifs confirmed by the archaeology places of the old civilizations of the word. The most remote constructions date from 10.000 years old in Jericoh, in the Jordan River Valley. This work became more intensive at 3.000 B.C. (Before Christ), by people who lived in those valleys with mood areas, a lot of clay and washed by the rivers.Almost all the sectors of engineering of soils choose the stability to use the local soil. Although, artificially treated, offers more economical advantages.The stability of a soil consist of endow it of the condition to resist the deformations and ruptures during the period that it is being used, because these characteristics are necessary in any construction.The application of the natural soil only is possible in places that they are of good quality and attend to the requirements of engineering to the type of previewed application. The granulemeter correction and the chemical stability include cases of inappropriate soils areas, turning the soil able to be used as construction material. Among the stability agents, usually added to the soil for stability ends, the cement is indicated."

Jan 1, 2013

By Ch. -A. Gandin, M. Rappaz

"The grain selection mechanism which occurs during the growth of columnar dendritic structures is routinely used in the investment casting industry to produce directionally solidified (DS) and single crystal turbine blades. However, the evolution of the grain density with increasing distance from the chill has rarely been correlated with the evolution of the grain texture. This contribution presents a three-dimensional (3-D) stochastic modeling approach which permits the computation of grain maps, pole figures and grain density evolutions in DS superalloys. These predictions are compared with measurements resulting from an automatic indexing technique of Electron Back-Scattered diffraction Patterns. This 3-D stochastic model, which applies to uniform temperature situations, has to be extended to the dendritic growth in a thermal gradient. As a preliminary step, a 2-D Cellular Automaton (CA) has been coupled recently to Finite Element (FE) heat flow computations in order to predict the grain structures in complex shape investment cast part. The application of this CAFE model to the investment casting of a turbine blade is presented. Considering these results, the extension of the CAFE algorithm to three dimensions is discussed.INTRODUCTIONThe selection of columnar grains during the directional solidification of alloys plays a key role during the investment casting of directionally solidified (DS) and single crystal (SC) components for aerospace applications [I]. This selection mechanism, leading to a competition of the dendritic network propagation at grain boundaries, has been the subject of many investigations. In particular, the study of Walton and Chalmers [2] is remarkable since it provides a link between the evolutions of the density and of the texture of columnar grains with increasing distance from the mold wall. Since this original work of Walton and Chalmers, two new tools have become available, which enable one to revisit the problem of grain selection in much greater depth. The first one is a fully automatic indexing technique of Electron Back-Scattered diffraction Patterns (EBSPs) [3-6] which directly gives the crystallographic orientation of the solid at any location of the specimen. Pole figures, orientation distributions, misorientations between grains can be visualized very easily with this technique. This information can be directly compared with the results of a second tool: a three-dimensional (3-D) stochastic model (SM) describing the nucleation and growth of grains in a uniform temperature field [6-9]. In order to extend this model to non-uniform temperature situations, a preliminary 2-D model has been developed [10]. It is based on a Cellular Automaton (CA) algorithm coupled with Finite Element (FE) heat flow computations. Since the details of both the automatic indexing technique of EBSPs and the simulation tools have already been published [3-10], only a brief summary is given here."

Jan 1, 1994

By Takeo Fujino, Nobuaki Sato, Yarong Wang, Kohta Yamada

"Ternary mixed sulfides of some transition metals MTS3 (M=Ba, ·Pb, T=Ti, Zr) were synthesized by a relatively low temperature process using sulfur melt. The mixture of starting materials, such as, metals and/or binary sulfides and a large excess of sulfur was reacted in a vacuum-sealed Pyrex or quartz ampoule at 350- 600 °C for one to three weeks. After the reaction, the remaining sulfur was completely removed by a process composed of filtration of sulfur melt and followed dissolution in CS2• The binary sulfides impurities coexisted in the products were removed by rinsing the products in water and acetone. By using the above method, BaTiS3, PbTiS3 and BaZrS3 'Were obtained in pure form. The effect of addition of halides on the yields of these ternary sulfides were also discussed.IntroductionThere have been a vast number of studies on the preparation and physical and /or chemical properties of mixed metal oxides. As is well known, some of such compounds exhibit excellent materials properties, causing them for use in mechanical, electronic, magnetic and chemical devices. Not a few mixed metal sulfides show similar physico-chemical properties to those of the corresponding mixed metal oxides. However, the study of the mixed sulfide crystals is rather sparse mainly due to difficulties in preparing these compounds. In various methods which have been adopted for preparing mixed sulfides, the simplest method would be the solid-solid reaction of the component binary sulfides or elements. However, there are always diffusional constraints with regard to the reactions in solid phases causing it necessary to heat the reactants at sufficiently high temperatures, viz. 800-1200°C. On the other hand, some mixed sulfides are unstable at high temperatures or to change their materials properties due to sulfur nonstoichiometry and structural modification depending on temperature, i.e., synthesis of such compounds needs to be made at lower temperatures. Processing in alkali halide melts is hopeful to overcome the above problems but to obtain the halide melts the temperatures above ~ 600 °C is needed. Low temperature reaction has been carried out for the preparation of Hg1.24TiS4, which was formed by the ·combination of TiS2 and molten Hg metal at 320°C[l]. Reaction of WS2 with LiBH4 melt at 350°C yielded LixWS2[2]. These sophisticated methods, however, can be applied only to the vary special cases."

Jan 1, 2000

By Suleyman Tekeli, Serdar Salman, Bulent Aktas

"The effect of La2O3 content up to 15 wt% on phase stability, sintering and microstructure of cubic zirconia (8YSZ) was investigated. XRD results showed that the specimens containing up to 15 wt% La2O3 were composed of only cubic structure. Also, the specimens doped up to 5 wt% La2O3 revealed no La2O3 peaks, indicating that La2O3 was completely solubilized in the cubic structure. However, when> 5 wt% La2O3 was added, the peak of La2Zr2O7 compound emerged, showing that the overdoped La2O3 was not solubilized in the 8YSZ matrix. The lattice parameter of the 8YSZ slightly decreased with the increasing La2O3 content up to 1 wt% but further increase in the La203 amount resulted in an increased lattice parameter. The comparison of grain size of the 8YSZ specimens with various La2O3 content showed that grain size slightly increased with the increasing La2O3 content up to 1 wt% but further increase in the La2O3 amount resulted in a decreased grain size.IntroductionAt atmospheric pressures, three polymorphic forms of Zr02 are stable at different temperatures i.e. monoclinic, tetragonal and cubic. A high-pressure orthorhombic form of Zr02 has also been reported[l]. The successful production of pure Zr02 bodies is not possible all the time due to the large volume expansion associated with the martensitic tetragonal-monoclinic transformation. This fact restricts the applications of zirconia, in spite of its excellent mechanical and thermal properties. However, the stabilization of the high temperature polymorphs at room temperature as stable phases is made possible by addition of suitable dopants. Fully stabilized cubic Zr02 and partially stabilized tetragonal Zr02 show interesting properties and are widely used as ionic conductors, coatings and gas sensors in solid oxide fuel cells and structural applications[2]. Most frequently used dopants include Y203, CaO, MgO and Ce02, although other oxides, such as those of rare earth elements, can also act as stabilizers of the high temperature structures. The incorporation of aliovalent cations to the lattice, forming substitutional solid solutions, allows to control the concentration of anionic vacancies in the structure. This aspect is particularly important in designing ionic conductors[3], and is also determinant in the stabilization process[ 4]. The process of stabilization with larger ionic radii dopants is rationalized by the crystal chemistry model[ 5], that describes the dopant cations as typical stabilizer when they have larger ionic size, lower charged state and higher ionicity than Zr4+ The ionic radius of Zr4+ is 0.84 Å and that for La3+ is 1.016 Å [6]."

Jan 1, 2012

By J. K. Brimacombe, I. V. Samarasekera, B. G. Thomas

"Mathematical models have been developed for the processing of static cast steel ingots and are app1ied to investigate the mechanisms for the formation of panel cracks. Panel cracking is an intermittent but persistent defect that causes affected steel ingots to be scrapped. A two-dimensional, finite-element, heat-transfer model was formulated and employed to calculate the temperature distribution in both large and small steel ingots during the various processing stages from initial casting to the start of rolling, including solidification, cooling in the mold and in air, reheating in the soaking pit, and subsequent air cooling. The stress state in the ingot arising from the calculated temperature variations was then determined. This involved the development of a transient, elasto-visco-plastic, finite element, thermal stress model, including the effects of phase transformation volume changes and kinetics creep, and temperature-dependent, mechanical properties. The results of the mathematical model predictions of temperature and stress were then used to determine the mechanisms and to suggest solutions for two different types of panel crack formation. Mid-face panel cracks apparently form during air cooling when the mid-face surface temperature is between the Arl and 500~C. Off-corner panel cracks appear to initiate internally during the early stages of reheating but do not propagate to the surface until much later. IntroductionPanel crack formation in static-cast steel ingots is a defect that has been plaguing the steel industry for several decades. Although the problem is intermittent, it is also serious since affected ingots must be scrapped. Panel cracks are manifested as two distinct types of cracking problems. ""Mid-face"" panel cracks are found exclusively in small, 2 to 6 ton, medium carbon steel (0.3 to 0.7% C) ingots and usually exhibit a single, continuous, longitudinal crack down the center of one of the ingot faces as shown in Fig. l (l). ""Off-corner"" panel cracks often form roughly oval, discontinuous crack patterns on the wide faces of large, 20 to 30 ton ingots as seen in Fig. 2 (2). They affect only low carbon steels (0. l to 0.2% C) with high manganese content. Both defects affect only aluminum-treated steels and are caused by a combination of intermediate temperature ductility loss involving aluminum-nitride precipitation and thermal stress generation. The ductility problem has received a good deal of attention which was the subject of a recent review (3). The present study was undertaken to investigate the thermal stress aspects of the problem through the development of mathematical models of heat transfer and stress generation in static-cast steel ingots. The ultimate objective was to elucidate the mechanisms of formation for both types of panel crack and to evaluate possible solutions to the problem."

Jan 1, 1986

By Yinlun Huang, Cristina Piluso

"Industrial sustainability looks to improve material and energy efficiencies, product quality and variety, and productivity within an industrial zone, thus pursuing the long-term sustainable development of the region. This paper introduces a systems-based modeling methodology, which provides industrial leaders with the ability to evaluate future production options to determine the path with the highest positive impact on both their own sustainability and the sustainability of the overall industrial zone. A comprehensive study on sustainable development of an auto-manufacturing focused industrial zone under uncertainty is illustrated. Introduction Sustainable development refers to a continuous process of improvements that must be followed in order to achieve a state of sustainability. In its most general form, a widely accepted definition of sustainable development was identified in the Brundtland Report as “development that meets the needs of the present without compromising the ability of future generations to meet their own needs” [1]. Sustainability will occur when the material and social conditions can be maintained or improved for human health and the environment over time without exceeding the ecological capabilities that support them [2]. An industrial zone is defined as a geographic area comprised of a network of industrial sectors, each composed of a number of entities. Such a zone is highly integrated and complex, and contains numerous uncertainties due to each industry’s extreme dependencies on its suppliers and customers throughout the product supply chain. In the context of an industrial zone, sustainable development refers to the continuous process of advancements in the zone, and the entities that comprise it, creating more value, wealth, and profits (economically viable dimension), providing environmentally benign products with less raw material consumption and waste generation (environmentally compatible dimension), and collaboration and a direct relationship among all involved in the supply chain, i.e. the corporations, employees, suppliers, investors, communities, customers, etc. (socially responsible dimension). These are the triple bottom lines of industrial sustainability. In order for economic, environmental, and social sustainability improvements to be successfully implemented within an industrial zone, the industrial decision makers must possess system-wide analysis abilities. The analysis of the sustainable development of an industrial zone involves decisions at the local, regional, or national levels, which are complex and involves handling of ill-defined parameters with a high degree of uncertainty due to the imperfect understanding of the underlying issues [3]. This work focuses strictly on the uncertainties in future zone planning and a method and a scenario based approach that can be used to evaluate the sustainable development of an industrial zone among these uncertainties."

Jan 1, 2008

By A. Dell’Era, M. Pasquali, C. Lupi

"An electrochemical cell has been designed to treat very diluted cobalt solutions, i.e. those deriving from recycling processes of lithium-ion batteries. A reticulated vitreous carbon sponge was used as cathode and a Pt-coated Ti net as anode. A controlled potential electrolysis has been carried out in a solution flowing in the cell and maintained at a constant pH of 6.5. Considering the cathode dimensions (10.0 cm * 10.0 cm * 1.25 cm), rather high volumes of solution (>1 litre) can be treated with flow rates up to 1.6 l/min. The process yield is obviously related to the solution concentration; it has been observed that, starting with a solution containing 200 ppm of Co2+, the yield is initially ~35-40%, but it decreases to ~20% when 80% of the initial cobalt content has been electrowon. The yield increases up to ~50% if the carbon electrode is coated by cobalt. The conditions allowing a fast and complete removal of cobalt are outlined. Introduction Industrial liquid effluents containing heavy metal ions arise not only during hydrometallurgical processing, but also in many sector of chemical industries utilizing metal catalysts and process reagents. These waste solutions containing low quantities of metallic ions can be treated by chemical precipitation, solvent extraction, ion exchange, etc. before final discharge. All these techniques could be efficient for complying the aqueous effluents with the severe rules related to the environmental impact, but they can not directly produce metals. Particularly the chemical precipitation presents two main drawbacks, huge amount of sludge prodction and reagent costs to produce this useless and sometime dangerous sludge that have to be considered. Electrochemical technologies can be used for the treatment of effluents polluted by metal ions, showing the following advantages in comparison with other processes: 1. recovering of the polluting substances in metallic forms, with subsequent reusing; 2. absence of process slag, which should be subsequently disposed of. In this work an electrochemical reactor with a reticulated vitreous carbon cathode and a platinated titanium net anode has been designed and utilized for removal Co from waste aqueous solutions. Porous materials have been used as electrodes for this cell, as their high specific surface area favours the treatment of these low metal content solutions (1-7). This kind of electrodic material presents very interesting chemical-physical characteristics such as: low density, low thermal expansion and high electrical and thermal conductivities; particularly the reticulated vitreous carbon (RVC) presents a very elevated void volume, rigid structure, good resistance to temperatures in non-oxidizing environments and very low resistance to fluid flow."

Jan 1, 2008

By Masatsugu Morimitsu

"The novel smart anode, MSA ™, for electrowinning of non-ferrous metals such as copper, zinc, nickel, and cobalt has been developed by thermal decomposition. The smart anode consists of a titanium substrate coated with a catalytic oxide layer which comprises amorphous or less crystalline oxide coatings. The catalytic layer contains an iridium oxide-based mixture or a ruthenium oxide-based mixture. The smart anode provides a remarkable reduction in cell voltage compared to other anodes, e.g., commercially available coated titanium electrodes and lead alloy electrodes. The test data has demonstrated that a maximum voltage reduction by ca. 30% is possible compared to lead alloy anodes. The smart anode also gives some additional merits in suppressing unwanted deposits on the anode; i.e., deposition of MnOOH, Pb02, or CoOOH. The electrowinning with the smart anode is possible to be an environmentally friendly process with less energy consumption and less anode deposits.IntroductionA coated titanium electrode iridium oxide-based or ruthenium oxide-based catalytic layers is well known as an insoluble anode for oxygen or chlorine evolution in industrial electrolysis such as chloro-alkali electrolysis, electrogalvanizing or electrotinning of a steel, a thin film production by electrodeposition such as copper foil production (CFP), water electrolysis, and electrowinning of nonferrous metals. The anode is commercially produced by thermal decomposition of a precursor solution painted on a titanium substrate, and the decomposition is usually performed at 450 °C or more. The obtained catalytic oxide coating formed on the substrate contains crystalline oxide as an active component to oxygen or chlorine evolution. The author of this paper had met a problem of such a crystalline oxide coating in the application of copper foil production; the anode was unable to use for a long period because of a large amount of lead oxide (Pb02) deposited on the anode, and the cell voltage was seen to continuously increase and drastically rise by the accumulated Pb02. In this case, the voltage reduction by replacing a lead alloy anode with the dimensionally stable anode was initially observed, but was gradually lost and disappeared. Therefore, the author of this paper aimed and investigated to suppress the unwanted side reaction on the anode, and finally invented a new class of coating based on an amorphous iridium oxide mixture in 2003 [!]. The invented coating was obtained at a low temperature thermal decomposition, e.g., 360 °C, and the coating consisted of amorphous iridium oxide and amorphous tantalum oxide. This invention achieved that oxygen evolution potential shifted more negative so that the cell voltage was reduced, and no Pb02 was deposited in the electrolyte of CFP [2,3]."

Jan 1, 2012

By S. Goto, S. Yamashita, K. Hata

"The average consumption of zinc dust for purification of zinc leaching solution is more than 25 kg per tonne of electrolytic zinc. Authors proposed to remove impurities in zinc leaching solution by electrolysis instead of cementation by zinc dust. The effects of copper and arsenic on electrodeposition of cobalt in zinc sulfate solution were examined fundamentally using a potentiostat. It is observed that cobalt is easily deposited on a cathode at potentials under -480mV with arsenic. Mesh cathodes of stainless steel and lead anodes were used in a small electrolytic cell and the electrolyte was circulated through 'the electrodes during the electrolysis. The effect of electrolyte circulating rate , pH, cell temperature, current density, and concentration of copper and arsenious ions on removal of cobalt were studied. Removal of Cd and Ni are also examined.IntroductionCobalt is difficult to remove from a zinc leaching solution by a simple cementation reaction using zinc dust. However, it is easily precipitated by zinc dust with co-addition of arsenious or stibinous oxide and copper ion in practical operations(I), (2), (3). The consumption of zinc dust for purification is 16-152 kg per tonne of electrolytic zinc and 65% of this zinc dust consumption is used for cobalt purification. The average retention time for purification of cobalt is 4.5 hours (1). A more economical process for purification is desired instead of zinc dust. The mechanism of this acceleration effect of copper and arsenious oxide on removal of cobalt are explained by the authorsas follows; a galvanic cell is formed between zinc dust and copper which is precipitated firstly, and cobalt is reduced on copper as Co-As alloy by this galvanic current(2). This assumption was confirmed in experiments using a galvanic cell with a membrane( 4). The following galvanic reactions occur between zinc dust and copper precipitate; on copper cathode,2H+ + 2e -= Hz(g)2Coz+ + 2HAs02 + 6H ++ 10e -= 2CoAs + 4HzOand on zinc anode,Zn = Zn = 2+ 2e –This galvanic current becomes almost zero in a zinc sulfate solution which includes only cobalt and no arsenious oxide, and cobalt is weakly deposited on a copper cathode. Cobalt deposition requiers a high degree of cathodic polarization. However, the galvanic current flows almost constantly in an electrolyte, which includes arsenious oxide, and the cathode potential is kept at about -500mV. Cobalt is precipitated as Co-As on the cathode.The authors assumed that cobalt may be removed by electrolysis at a very low current density instead of zinc dust and the following experiments were carried out. In the first part of this paper, the fundamental experiments using a potentiostat on the behaviour of cobalt in zinc sulfate solution are described. In the second part, the results of the electrolysis are reported. Cobalt is removed by a new type of an electrolytic cell, which was desigoed to <Iccelerate the rate of deposition of cobalt. The removal of cadmium and nickel in a solution which includes cobalt and arsenic are also examined."

Jan 1, 1997

By Sridhar Komarneni

"Microwave-hydrothermal processing is a novel technique which combines the conventional hydrothermal processing with microwave field and we previously showed for the first time, that ceramic powders can be rapidly produced by this technique. This review paper deals with the synthesis of unary oxides such as Fe203, Ti02, Zr02, etc., binary oxides such as BaTiO3, SrTiO 3, PbTiO 3, SrZrO 3, KNbO3, etc., and ternary oxides such as NaTi2 (PO4)3 and pyrochlore phases of Pb(Mg1/3Nb2/3)O3, Pb(Zn1/3Nb2/3)O3 etc. and metal powders such as Cu, Ni, etc. below 195°C. This method can be adopted to the synthesis of a large variety of powders by the appropriate control of pH, Eh, temperature/pressure and concentration of chemical species. The main advantages of this method compared to conventional hydrothermal processing are (a) it increases the kinetics of reaction by one to two orders of magnitude, and (b) it can lead to novel phases especially those with layered structures.IntroductionConventional hydrothermal processing is a well-established synthesis technique which has been extensively used in the preparation of fine ceramic powders [1-5], large single crystals [6-8] and massive cement blocks [9]. Technologically important ceramic powders such as BaTiO 3, Al203 etc. made by the hydrothermal process are now commercially available. Although there are numerous methods for materials synthesis, hydrothermal method is truly a low temperature and environmentally benign process. For example, ZrSi04 (Zircon) which is extensively used in ceramic industry can be prepared hydrothermally at 150·C [10] compared to sol-gel or solid-state method [11,12] which require a temperature of about 1000·C. The hydrothermal method is environmentally benign because hydrothermal reactions are carried out in closed systems at low temperatures and the contents can be recovered and recycled after cooling to the ambient conditions. One of the disadvantages with any low temperature processing method is slow kinetics. For this reason we have combined the hydrothermal method with microwaves to enhance kinetics and we named this method as ""Microwave-hydrothermal"" processing [13- 16]. Although the combination of microwave and hydrothermal techniques has been used in the past few years to dissolve all kinds of inorganic (e.g. alumino silicate rocks) and organic materials rapidly for chemical analysis, we were the first to show its potential value for the synthesis of various ceramic powders [13-16]. In this paper, I show that this novel method is applicable to the synthesis of all unary, binary and multinary oxides by the appropriate control of pH, Eh, temperature, pressure and concentration of chemical species. In addition, this method is also found to be useful for the preparation of metal powders."

Jan 1, 1994

By Fiseha Tesfaye, Pekka Taskinen

"A thermodynamic study of the equilibrium phase assemblage AgBi3S5-Bi2S3-S was made by an EMF-technique, using the RbAg4l5 solid electrolyte. The ternary phase was synthesized from the pure Ag2S and Bi2S3 in an evacuated silica ampoule and grinded into powder and mixed with appropriate compositions of B12S3 and S, in a series of experiments, for pressing in to pellets. The pellets were assembled to form the galvanic cells Pt (-) | Ag ] RbAg4ls | AgBi3S5+ Bi2S3 + S + (C) I Pt (+). The EMF-measurements were made in the temperature range 299 - 460 K.In this paper, thermodynamic functions of the ternary phase AgBi3S5 (pavonite) have been determined. The agreement between the obtained results and the literature values were established.IntroductionThe complex group of ore minerals constitutes from trace amounts to a major proportions of sulfosalts. Although the sulfosalts rarely form massive ore bodies, they are commonly associated with rich sulfide ore minerals for the base and precious metals and widely distributed in a metal poor sulfide minerals [1]. For instance, Ag-bearing sulfosalts are encountered in ore minerals for the production of the base metals and are common sources of silver. Nevertheless, thermodynamic properties of the sulfosalts are poorly known.Reliable thermochemical data are essential for quantitative modeling of the chemical behavior of the sulfosalts in equilibrium with sulfides, which in turn would promote the optimization of complex minerals treatment and extractive metallurgy of the valuable metals."

Jan 1, 2012

By M. O. Lai

"Metal matrix composite (MMC) with composition of Al-4.Swt.%Cu reinforced by IOwt.%TiB2 or ISwt.%SiC particulate has been successfully fabricated using powder metallurgy technique. Disk, compression and beam specimens were prepared with (a) layered structure containing ductile Al-4.Swt.%Cu with brittle Al-4.Swt.%Cu/TiB2 or Al-4.Swt.%Cu/SiC layers, and (b) homogenous constituent with composition of Al-4.Swt.%Cu/lOwt.%TiB2' The specimens for the fracture toughness measurement were built through three ductile-brittle-ductile alternating layers. For the beam specimens, the layers were built through brittle-ductile-brittle sequence. The brittle layer consisted of Al-4.S%Cu with fixed amount of reinforcement. Fracture toughness testing revealed an increase for layered composites although the total amount of the reinforcement was the same for all disk specimens. The increase in fracture toughness is due to the existence of ductile layers which manifests a strong influence on delaying the occurrence of fracture. It acts as a barrier to resist the propagation of crack and hence increases the fracture toughness of the layered MMC specimens, Delamination in the beam specimens was observed to be due to shear stresses. Fracture surfaces of both disk, compress and beam specimens were characterized using the SEM. IntroductionMechanical and thermal properties can be achieved by the incorporation of refractory secondary phases to constrain the plastic flow of the matrix in a metal matrix composite (MMC). The size of the reinforcement particulate incorporated must be in the range larger than the dislocation cell size and strongly bonded to the matrix (I). Particulate reinforced metal matrix composites hence provide high modulus, improved wear resistance and strength (2-4). Because of the incorporation of refractory phases which are generally brittle, the major limitation in the mechanical properties of MMCs is their limited ductility in comparison to their base metals. Cracks normally initiate from the reinforcement and voids (4, 5). Due to the lack of ductility, cracks propagate rapidly with increase in load. As a result, the interactions between reinforcement particles and propagating cracks have recently been of great research interest (6). In addition, volume fraction of reinforcement and aging condition of the matrix significantly affect the mechanical behaviour of MMCs. In the case of AI-3.5%Cu reinforced with varying volume fractions of SiC particulate, it has been found that the probability of particle fracture increased with increasing volume fraction of reinforcement (7)."

Jan 1, 1996

By Dong Liu, Zejian Yang, Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"The structure, composition, morphology, and adsorption property of UV-vis light of as-prepared samples were characterized using XRD, SEM, FTIR-EDS, and UV-vis DRS. UV-visible light induced photocatalytic degradation of methylene blue ~) over Ti02-doped diopside was investigated. Experimental results show that doping Fe + induced the formation of Ti-0 or Ti-0-Si in diopside, and promoted the light adsorption property of diopside. Photocatalytic reactivity of Ti02-doped diopside obviously depended on content of doping Ti02. The diopside with 3% Ti02 exhibited the superior photocatalytic activity with 76% degradation of methylene blue under light irradiation for 3 h.IntroductionPhotocatalytic technology has been extensively studied in the process of dealing with inorganic and organic pollutants. Ti02, with its own non-toxic, stable, low-cost and other advantages, has become the most widely studied photocatalytic materials[l-SJ_ The low utilization quantum made it restricted in the practical application. SrTi03 as the representative of the perovskite[9·121, Bi2W06 for the composite oxide[13,141, also attracted wide interest in the photocatalytic studies. However, these photocatalytic material has been mostly prepared in relatively strict experimental conditions with chemical reagents, they had small production, high cost, which made them difficult for practical applications.In our country, there has 400 million tonnes of ti-bearing blast furnace slag (TBBFS) each year in the process of smelting pig iron, which has lead to waste of titanium resources and pollution of the surrounding environment. In recent years, studies have shown that TBBFS instead of pure Ti02 to be photocatalytic materials is feasible[ 151. TBBFS has not only been higher photocatalytic degradation activity for the o-nitrophenol, methyl orange, nitrobenzene and other organic matter[16-191,but also exhibited excellent in the process of dealing with inorganic heavy metals in waste water (containing Cr6+i201. If TBBFS can be successfully applied to photocatalytic technology, the will make large accumulation of titanium-bearing slag reasonable used, so as promote the re-use of energy. At present, our understanding of the photocatalytic activity of TBBFS is steadily deepening. Photocatalytic activity ofCaTi03 has been reported as one of the main minerals ofTBBFS [21'21J, However, there were few studies for Another major mineral of TBBFS - diopside which had the content of9-15%. diopside would doped with Ti02 In the process of smelting pig iron, therefore, Ti02-doped diopside's photocatalytic activity in the UV-Vis was mainly studied in this paper."

Jan 1, 2013

By Jeffrey Shepherd, Scott R. Smith, Eduard Guerra

"Electrochemical and spectroscopic evidence for the dissolution of a Au electrode by meso-2,3- dimercaptosuccinic acid (DMSA) from an acidic LiCl04 electrolyte is presented. Near the potential of zero charge, DMSA was determined to form a stable layer on the metal surface but at more anodic polarizations, DMSA was displaced from the metal through an oxidative process. The anodic displacement of the layer from the electrode resulted in a small amount of Au that was detected in the electrolyte using atomic absorption analysis. The extent of Au dissolution, was monitored while holding the potential of the electrode for 24 hours at the thermodynamic Eo/H,O in LiCl04 electrolytes containing 10 mM DMSA. This routine resulted in detectable quantities of a soluble Au-DMSA complex in the electrolyte and the greatest leaching was observed at a pH = 2.0. At room temperature, the leaching rate was stable at 10.9 µg cm·2 hr·' however, upon increasing the temperature to 50.0°C, the rate of Au dissolution increased yielding an average rate of extraction of 40.1 µg cm·2 hr- 1. Interestingly, after the first 12 hours of leaching at 50.0°C, the leaching current decreased dramatically suggesting surface passivation which prevented further Au extraction. The implications of this process in the industrial leaching of Au will be discussed.IntroductionThe use of cyanide in the industrial process of leaching Au from ores has raised concerns regarding both operational safety and environmental issues surrounding the disposal of spent leaching eftluents in tailings ponds. Depending on the chemical nature of the processed ore, the spent solutions that are released into the tailings ponds can contain toxic cyanide, either dissolved or complexed with different metals and may pose serious risk to wildlife as well as freshwater contamination to nearby water systems. Because of these issues, some recent studies have focused on the exploration of more environmentally-friendly molecules to selectively leach Au with appropriate kinetics. However, to effectively leach Au into an aqueous solution, a suitable ligand that reacts to form a stable chemical bond with Au is needed to form soluble Au complexes that can be later recovered [I]. Recently several sulfur bearing alternatives have been shown to leach significant quantities of Au in aqueous solutions. These include thiourea [2], thiocyanate [3], and thiosulphate [4]. However, alkylthiols are also known to quickly form a stable covalent Au-S bond [5], but have been relatively understudied in term of their ability to leach Au in solution, even though some short chain thiols are water soluble and relatively nontoxic."

Jan 1, 2012

By Bora Derin, Sertac Yazici, M. Seref Sonmez

"In this study, the recycling conditions of waste liquor obtained after the production of tungsten boride powder from calcium tungstate by self-propagating high temperature synthesis (SHS) and the following hydrochloric acid leaching were investigated in detail. Environmentally unfriendly and extremely acidic (pH~ -0.3) liquor consisting of calcium, magnesium, and boron ions was treated with 1 M sodium carbonate solution to precipitate magnesium carbonate and calcium carbonate phases. The obtained amorphous precipitates were heated up to the temperature of 400°C for re-crystallization. As a result, MgO, CaC03 and CaMg(C03)z phases were obtained, while sodium, boron, chlorine ions were remain in the solution. The present study is still in progress.IntroductionSelf-propagating high temperature synthesis (SHS) is one of the techniques used in the production of a variety of advanced ceramics, inter-metallic, organic and inorganic compounds, oxygen free single crystals, and polymers [ 1, 2]. The reaction becomes selfsustaining and propagates in the reactant mixture, after initiation in SHS process. SHS products may contain the mixture of several unwanted compounds and elements. Therefore following acidic leaching process may be needed to purify the target product. In the previous study, calcium tungstate (Ca W04), magnesium (Mg) and boric acid (B20 3) mixture were reacted to produce tungsten boride powder by SHS process according to the Reaction 1. Then, magnesium and calcium containing byproducts (i.e. MgO, Mg3B206 and Ca3B206) found in the SHS product were leached out by using concentrated hydrochloric acid (HCl) solution to obtain pure tungsten boride powder [3].Ca W04 + 0.5B203 + 4.5Mg = WB + 4.5Mg0 + Cao (1)After the leaching, filtrate solution consisting of different amounts of magnesium, calcium, and boron requires additional treatment for the environmentally acceptable disposal.Several works were carried out about magnesium precipitation conditions and kinetics from brines. Rabadzhieva et al. investigated the precipitation of Mg(OH)z from brines by using NaOH as well as caustic soda [ 4]. Turek ve Gnot investigated the precipitation efficiency of Mg(OH)z for the temperature range between 10-40°C, while the reaction was kinetically experimented by Alamdiri et al [5, 6]. Homogeneous precipitation of nesquehonite (MgC03.3H20) by the reaction of MgCli with (NH4)2C03 in supersaturated solutions and factors that influence the precipitation of MgC03.3H20, such as reaction temperature, initial concentration, stirring speed, titration speed, equilibration time, have been studied by Wang et al [7]. The precipitation of Mg(OH)z by calcium hydroxide from aqueous solutions was studied by Baird et al. [8]. Stratful et al. focused on conditions influencing the precipitation of magnesium ammonium phosphate from wastewaters [9]. 1031"

Jan 1, 2011

By Xin-liang Gao, Qing Li, Gui-qin Fu, Duo Jin, Miao-yong Zhu

"Optical microscope together with alternative wet-dry cyclic accelerated corrosion tests and XRD, SEM were employed on bridge weathering steel samples with different Mn and Ni contents which were vacuum induction melted and rolled to study their effects on the microstructure and rust layer evolution in er' containing condition. The results show that the microstructure is mainly ferrite and pearlite when Mn and Ni contents are 0.75 %, 0.42 %, respectively. Both the increase of Mn and Ni contents will make pearlite disappear while granular bainite appear, meanwhile the grain size decreases. With the increase of Mn content, the corrosion rate decreases in the initial stage, but the effect becomes little in the later stage. The increase of Ni not only improves the corrosion resistance of steel base at the initial stage but also hinders the tendency of further corrosion. As Mn content increases, a-FeOOH contents in rust layer decreases. With increase of Ni content, the content of a-FeOOH in the rust increases while that ofy-FeOOH decreases.IntroductionWeathering steels had been ~radually applied in manufacture of bridges owing to reducing the corrosion rate remarkably [I- l .Good weldability was needed for high performance bridge weathering steels. Since carbon was thought to be bad for weldability, low carbon content steel was adopted and Mn was added to amend the mechanical strength loss. Some scholars[6, 7l believed that Mn was beneficial for increasing corrosion resistance performance of the steel in marine atmospheric environment. Some scholars [S, 9l thought that Mn had little effect on corrosion resistance in marine atmospheric environment. Presently, the effect of Mn on bridge weathering steel in marine atmospheric environment still remained poorly understood. Ni was considered to be beneficial for increasing corrosion resistance performance in marine atmospheric environment [JO-l4l However, the high cost limited its application range. What would bring to the rust and corrosion by decreasing Ni content needed further research.Most researchers assumed that microstructures only affected the corrosion behavior of bare steel. But the study of Guo et al. P5l showed that the homogenous microstructures were beneficial for the corrosion resistance of steels. The effect of Mn, Ni content change on microstructure and microstructure on corrosion still remained poorly understood. In the present work, the effect of Mn and Ni on the microstructures of steel matrix, as well as the microstructures on the rust and corrosion was investigated."

Jan 1, 2014

By Chu Yong Cheng

The solvent extraction (SX) processes of the three pressure acid leach (PAL) nickel plants in Western Australia have been reviewed. The use of intermediate precipitation, solids/liquid separation and re-leach in the three W A nickel plants make these processes complicated and costly in capital and ?operation. The research work carried out by the SX group at the AJ Parker Cooperative Research Centre for Hydrometallurgy I CSIRO Minerals has led to the development of direct solvent extraction (DSX) processes to recover and purify nickel and cobalt from leach solutions. The simplicity of the process flowsheets and the expected savings in capital and operating costs are the major advantages of the new DSX processes over the reviewed processes. By using a new synergistic organic system in semi-continuous tests with a pilot plant leach solution (after iron precipitation) from BHP-BiIliton Stainless Steel Materials, the metal values (Ni and Co) together with zinc and copper were separated from the major impurities (Mn, Mg and Ca, together with Cl) in the first SX circuit. The co-extracted manganese, magnesium and&apos; calcium were easily scrubbed out. After stripping, the metal values (Ni and Co) together with zinc and copper were concentrated, resulting in a much smaller second SX circuit and equipment in the down stream processes. The extraction and stripping kinetics of the metals with the new synergistic organic solution were very fast. The extraction and stripping almost reached steady state within 0.5 minutes. Semi-continuous test work with a synthetic leach solution, a cobalt pilot plant leach solution from Peko Rehabilitation Project Pty Ltd and a synthetic solution to simulate a concentrated laterite leach solution from BHP-Billiton Stainless Steel Materials showed that manganese, calcium, copper and zinc can be effectively and efficiently separated from nickel, cobalt and magnesium by extraction, scrubbing and stripping. This led to the development of another DSX process using D2EHPA to recover nickel and cobalt from leach solutions.

Jan 1, 2003

By V. K. Handa

Sterlite Industries (I) Ltd. started its copper smelter in 1996 and worked through the common problems associated with smelter start-ups. Specific issues in the converter area included converter blower IGV problems, punching machine reliability, converter spitting, back collar burning, ,and short converter campaign life. With a very young and dedicated team of engineers and technicians, smelter management assigned teams of three to four members to work scientifically and systematically through each major problem area to recommend and implement appropriate solutions. The converter mouth was redesigned with respect to tuyere and metal height to eliminate spitting and back collar burning. The air line was changed in places to reduce the pressure drop. A new back-up compressed air line and vessel was installed to prevent tuyere blockage in the event of a blower trip or power failure. The converter mouth liners and bricking around the mouth was modified to eliminate metal leaking through the pouring lip Modifications to the punching machines were made to address specific problems and preventative maintenance practices were further streamlined and reinforced to ensure 100% availability of hot metal cranes, converter blowers, punching machines, and ID fans. Matte availability and matte temperatures were improved by streamlining the upstream ISA and Rotary Holding furnace areas. Implementation of a detailed training program for the converter operators significantly improved the operation and morale. Water-cooled double hoods and a third converter were installed as part of the smelter modernization plan. The new hoods dramatically improved hygiene in the crane aisle while the addition of the third converter posed new challenges for the same motivated group of crews with respect to flip flop operation to keep the idle converter hot and to maximize in-stack time, managing crane/ladle logistics, and managing revert generation. This paper describes the converter operation&apos;s journey from the initial days of long blowing times and large revert accumulations to present operations with two converter flip flop operation, and also describes the team work, constant focus on increasing productivity and reducing costs, and benchmarking.

Jan 1, 2002

By Hubert Bril, Priscilla Pareuil, François Bordas, Emmanuel Joussein, Jean-Claude Bollinger

"According to the legislation, valorization type, origin and characteristics of waste material, various standard procedures are available to evaluate environmental impacts. A Mn-rich slag was sampled from a metallurgical plant. After its characterization (elementary analysis and mineralogy), five standard procedures were carried out (i.e. TCLP, EN 12457-1). Each fixed parameter of the standards was systematically studied in a large range: pH, Liquid/Solid ratio, contact time. For example, EN 12457-1 led to a low ME mobilization, increasing with the L/S ratio, the contact time and an acidic pH. As a conclusion, the representativeness of the considered parameters and their potential variations are predominant to assess of the real environmental impact during slag reuse. Introduction Recent studies have been carried out about environmental impacts of waste containing metallic elements (ME) because of their potential mobility [1-7]. Indeed, slags are either dumped or valorized in various activities such as building materials. In order to assess environmental risk, various standard procedures are used depending on country legislation, origin of waste and valorization way. Results of leaching tests are linked either to special legislation (e.g. Dumping: EC, Council Decision 2003/33/EC, Construction products: EC, Council Directive 89/106/EEC) or to legal levels used in drinking water (Directive 98/83/CE) when leachates could migrate to groundwater. If ME in leachates are lower than drinking water authorized levels, the waste will be considered as non-hazardous. On the contrary, if the leachable amounts exceed them, the question about the risk has to be posed. Beyond the abundance of leaching tests available, variety of operational conditions induced by these regulatory tests does not make the choice easier. According to operational conditions induced, ME release could vary from one test to another one. ME concentrations in leachates depend on pH, Liquid/Solid ratio, contact time and particle size [3]. To highlight the importance of these operational parameters, potential risk for valorization of a manganese-rich slag was assessed by comparing several standard leaching protocols [8-12] with a global study dealing with the influence of operational conditions. For each regulatory protocol, the most influential parameters (L/S ratio, pH, particle size and contact time) have been studied in a large range."

Jan 1, 2008

By G. Bjorling

After complete dissolution of chalcopyrite concentrate in sulphuric acid in presence of nitric acid the excess of the latter is expelled by a surplus of concentrate and the last traces of nitrate removed in the mother liquor after crystallization of the copper and iron sulphates. Zinc accumulates in the mother liquor from which it can be removed by solvent extraction of zinc sulphate as a pair of ions. After dissolution of the sulphate crystals in water the neutral solution is oxidized in an autoclave at 140°C where iron sulphate is thermally hydrolyzed; the iron-free solution is taken to copper electrowinning and the cell acid after partial evaporation recirculated with the mother liquor to the leaching circuit. Total recovery of copper is about 96%; other metals like zinc and iron are concentrated in industrially usable products. At a copper price of about 70 c/lb, the method appears to be profitable also in a small unit.

Jan 1, 1976