Search Documents

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013

By Shadia J. Ikhmayies

"Nanocrystalline fluorine doped tin oxide (Sn02:F) thin films were produced by the spray pyrolysis technique (SP) on glass substrates at a substrate temperature T, = 450 ° C. The hydrated stannous chloride (SnClz.2H20) was used as a precursor and ammonium fluoride (NH4F) and hydrofluoric acid (HF) were used as the doping compounds. A comparison between the compositional, morphological and optical properties of the films obtained by using the two doping compounds was performed by using scanning electron microscope (SEM) observations, energy dispersive spectroscopy by X-rays (EDAX) and transmittance measurements. It is found that the films prepared by using HF have larger grain size, and higher fluorine content than the films prepared by using ~- In addition these films have higher transmittance and higher direct optical bandgap energy. These results are interesting for the use of Sn02:F as a forecontact in CdS/CdTe solar cells.IntroductionTin dioxide is an n-type, wide bandgap semiconductor (about 3.5 eV) and in the form of thin films, it is a transparent conducting material, characterized by high optical transmission (80- 90%) [l]. Sn02:F is the most widely used transparent-conducting oxide material. The transparent-conducting thin films of this oxide are used as electrodes in a variety of optoelectronic devices, as heat mirror coatings in 'smart windows' for buildings, in automobile and airplane windshields, in incandescent light bulbs, in flat-plate and concentrating solar collectors. Tin oxide and zinc oxide, in thin film configuration are technologically important materials because of their applications in photovoltaic cells [2].Among various dopants for Sn02, fluorine is often preferred, because fluorine doping results in films with high transparency and good conductivity [3]. By exploring the literatures, it was found that different sources of fluorine were used to produce Sn02:F thin fihns, among which are ammonium fluoride (NH4F) and hydrofluoric acid (HF) are the most used. Some researchers used~ [2, 4-7] and others used HF [3, 6-8] for doping Sn02 films. Gordillo et al.[7] used both of NH4F and HF and showed that the resistivity of thin films obtained by using HF was lower than that of similar films obtained by using NH4F by a factor of 2.2. They also found that the films obtained by using HF have more random orientations."

Jan 1, 2013

By Tadafumi Adschiri

"Supercritical water can provide an unique reaction atmosphere for synthesizing metal oxide nanoparticles. Due to the drastic change of properties of water around the critical point, including density, dielectric constant and ionic product, the reaction phase with O 2 or H2 gas and the reaction rate and equilibrium can be varied to synthesize new materials or define particle morphologies. In this work, hydrothermal crystallization experiments are performed with several types of flow apparatus that allow convenient manipulation of variables such as temperature, pressure, and residence time. Key features in the flow modes and material preparation are discussed. The proposed supercritical hydrothermal synthesis method has the following desirable features: i) nanoparticles can be produced, ii) morphology of the produced particles can be controlled with small changes in pressure or temperature, and iii) a reducing or oxidizing atmosphere can be applied by introducing oxygen or hydrogen or other gases. An overview of this method is given for functional material synthesis of significant industrial interest including barium hexaferrite magnetic particles, YAO/Tb phosphor fine particles and lithium cobalt fine crystals.IntroductionHydrothermal crystallization, a method of metal oxide formation from metal salt solutions, is typically used at temperatures ranging from 373 K to 473 K. We are developing a new process for hydrothermal crystallizations that uses temperatures in the range of 673 K to 723 K, which is just above the critical temperature of water1 • 8 • In this work, we refer to this process as supercritical hydrothermal synthesis. The supercritical state of water allows one to vary reaction rate and reaction equilibrium by shifting the dielectric constant and solvent density with pressure and temperature. From of our research on material production in supercritical water, we have identified the following specific features of the supercritical hydrothermal synthesis method: (i) ultrafine particles can be produced, (ii) morphology of the produced particles can be controlled to some extent with pressure and/or temperature, and (iii) a homogeneous reducing or oxidizing atmospheres can be provided by introducing gases, such as O 2, H2, H2O 2• and so on.1"

Jan 1, 2000

By Xiaoming Huaa

The effect of the anodic polarization on the composition and morphology of the surface layer formed on chalcopyrite during ammonia–ammonium chloride leaching was investigated. The anodic polarization on the chalcopyrite electrode was used for oxidation and dissolution of chalcopyrite, and the resulting oxidized layers were characterized by XPS, SEM and optical microscopy. The results show that oxide layers exist on the chalcopyrite surface with or without any anodic polarization in the leaching solution at ambient atmosphere. However, the composition and morphology of the layers are strongly depended on the extent of polarization. The distribution of FeOOH and Fe2O3 within the oxidized layer was inhomogeneous for the sample at the open circuit potential (OCP). The composition and morphology of the oxidized layers which were formed at anodic potentials lower than 0.3 V versus SCE were similar to those of the chalcopyrite at the OCP. At anodic potentials above 0.4 V, the oxidized layers contained many cracks, and they were fragile and exfoliated. Furthermore, the sulfide had been oxidized to sulfur species with higher oxidation states. The oxidation of the chalcopyrite seemed to undergo a cyclically oxidative process that suggested growth and spallation of oxidation layers on chalcopyrite in a layer-by-layer sequence.

By Chang Wei, Zhigan Deng, Minting Li, Cunxiong Li, Xingbin Li

A direct hydrometallurgical process of extraction molybdenum and nickel from molybdenum-nickel ore by pressure water leaching without reagent was studied. The extraction of Mo and Ni from molybdenum-nickel ore by oxygen pressure leaching, which exploit the characteristic of molybdenum-nickel minerals contain high concentration amorphous sulfide which has highly active, and make the most of easily oxide to sulfuric acid and sulfate at low temperature and excess oxygen presence of the amorphous sulfide. Under oxygen pressure conditions, considerable molybdenum and almost all the nickel were extracted into solution in the leaching process. The results show that with the leaching time for 3~4h, temperature at 150o C, liquid-to-solid ratio of 2mL/g, mineral granularity of 0.074mm, oxygen partial pressure of 0.4~0.5MPa without other reagent, molybdenum leaching percentage can be over 80% and nickel leaching percentage can be more than 97%. Furthermore, about 80% sulfur in the Mo-Ni ore has been transformed into sulfuric acid.

Jan 1, 2014

By Edgar E. Vidal, Keith Smith, James A. Yurko

Beryllium, like many other reactive metals, is extracted from a halide (generally BeF2) using magnesiothermic reduction, also known as the Kroll process. The beryllium is produced in a molten state, which when solidified resemble "pebbles". Although beryllium is used in limited quantities compared to other metals (< 100 Mt/annual), it is a critical material for the nuclear, defense/aerospace, and large science markets because of its unique nuclear and mechanical properties. Beryllium processing has unique environmental, health, and safety concerns which must be handled appropriately in the 21st century from a worker and environmental safety perspective, and must be designed with this first in mind. In 2011, Materion began operations of its new Kroll plant – informally known as the “Pebbles Plant” - in Elmore, Ohio. The plant was majority funded by a U.S. Department of Defense Production Act (DPA) Title III grant, which is a unique government/industry partnership program to, "create assured, affordable, and commercially viable production capabilities and capacities for items essential for national defense." After a twelve year hiatus from primary beryllium production, Materion has reentered its extraction business and has relearned how to make pebbles. The purpose of this presentation is to give an overview on beryllium extraction and discuss some of the unique aspects of building and operating a safe beryllium facility during the production scale-up phase.

Jan 1, 2015

By Laila A. Guirguis

Impurities are removed from crude phosphoric acid (57.75% P2O5) with a mixture of low and high molecular weight alcohols, one of which is hydrophilic and the other is hydrophobic i.e. methanol and hexanol. In a single stage, the phosphate values segregate to the high molecular weight alcohol fraction and the impurities segregate to the low molecular weight alcohol fraction. The optimum ratio for the extraction is found to be 0.5 part methanol, one part impure acid and four parts hexanol where an extraction percent of more than 95% is achieved. Re-extraction of the phosphate value from the solvent is obtained by 6% phosphoric acid and the different factors affecting the re-extraction process have been studied. Finally, the purified acid is concentrated under reduced pressure and passed through activated carbon column, whereas the alcohols are re-circulated. The produced phosphoric acid was found to be in good match with the international specifications of food grade quality acid. A technological flow sheet is elucidated.

Jan 1, 2006

By Louis J. Cabri

The ion microprobe (dynamic SIMS technique) is a very sensitive instrument for the quantitative determination of trace concentrations of precious metals (often at the ppb level) occurring in common sulfide minerals, either chemically-bound or as discrete particles too small for resolution by SEM. The technique involves sputtering a 250 x 250 Jim area of the grains to a depth of about one ILm and analysing the secondary ions emitted from a circular central region in the sputter crater with a 62.5 I&apos;m diameter. The combination of quantitative mineral-specific sub-ppm analyses together with depth-profiling and the ability to produce secondary ion maps of trace precious metals makes this a very powerful technique in quantifying the precious metal distribution in refractory and other sulfide ores and process products. The technique is particularly well-established for analysis of gold-and platinum-bearing ores and process products.

Jan 1, 1996

By Marcela Morvová, Mário Janda, Morva Imrich

"The possibilities of greenhouse gas mitigation using various methods are brought out. The special case of utilization of mixture of CO2 with other greenhouse gases in a synergetic way inside non-thermal plasma based system is described in detail.Measurements on pilot system comprising pyrolysis chamber as alternative energy system (production of hydrogen and liquid tar) were made for various biomass and waste as the input material. The exhaust from this system was treated with non-thermal plasma gap suitable for up to 650Nm3/hour of exhaust gas flow. Condensable portion of exhaust is liquefied in distillation unit; produced hydrogen is stored on-line inside nano sized carbon of our own production.The CO2 removal efficiency varies depending on exhaust composition between 45 to 98%. Other oxides as CO, NOx, SOx and several hydrocarbons and VOC are also removed. The main product connected with CO2 removal is a solid powder of proteinoid nature. There exist strong probability, that precursor of the origin of life on the Earth from primary atmosphere were formed in the similar way as it is present in the electric discharge system used. Our system is equipped with on-line as well as ex-post analysis of all forms of products. We have also developed a system for recuperation of all forms of produced heat. It is stored inside as latent heat of waxes.IntroductionNatural greenhouse effect on the Earth is caused mainly by water vapour with the average absolute concentration about 4%. Other gases able to absorb long-wave radiation and thus this causing greenhouse effect are CO2, CH4, N2O, halocarbons and as precursors ozone and NOX. Some of them we produce and introduce into atmosphere in large quantities during production of energy and in transport. This factor leads to permanent increase of average temperature of air, sea and oceans, so called global warming.Nowadays large amount of data exists showing that the temperature of Earth in the last 150 years has been continually increasing. It represents about 03°C per ten years and the most of climatologist believe, that the increased concentration of greenhouse gases in the atmosphere is responsible for this effect.The most important greenhouse gas is carbon dioxide CO2. Majority of CO2 emissions comes from electric power stations working with fossil fuels, cars and industry. Burning of fossil fuels contribute up to 80% to world wide anthropogenetic emissions of CO2."

Jan 1, 2010

By Basak Anameric

Pig iron nugget process was developed by Kobe Steel as an environmentally friendlier, economical alternative to traditional blast furnace process. The process aimed to produce highly metallized, slag free pig iron nuggets throughout a single stage heat treatment, utilizing coal as a reducing ? carburizing agent. The objective of this work was to determine whether the pig iron nuggets produced at the laboratory conditions had comparable physical and chemical properties with the blast furnace pig iron. The physical and chemical properties of the pig iron nuggets were determined utilizing x-ray fluorescence spectroscopy, x-ray diffraction, optical microscopy, scanning electron microscopy, energy dispersive spectroscopy and apparent density measurements. The pig iron nuggets had similar chemical composition and apparent density values (6.7 ? 7 g/cm3) with blast furnace pig iron and they had microstructures similar to low carbon white cast iron. These properties make them a competitive alternative to blast furnace pig iron.

Jan 1, 2006

By Corby G. Anderson

Laboratory testing, interpretation and application of metallurgical technologies can be tedious, time consuming and costly. This paper outlines the use of proven statistical design of experimentation software for rapid optimization of laboratory testing and operating plants with limited representative sample utilization. This results in less costly required testing, a more thorough understanding of results and the ability to simultaneously optimize several variables and outcomes at once. At the Center for Advanced Mineral and Metallurgical Processing, this testing methodology has been used successfully in many metallurgical development and plant optimization projects thereby confirming its real world utility and application. Accordingly, several applied examples in flotation and hydrometallurgy will be outlined in this paper. This will include flotation testing of a copper gold ore, flotation testing of a copper, cobalt and gold ore, optimization of an industrial hydrometallurgical jarosite circuit and optimization of industrial nitrogen species catalyzed pressure leaching of a copper enargite concentrate.

Jan 1, 2006

By Chai Li-yuan

The anodic behavior of AZ31 magnesium alloy in NaOH alkaline solution was investigated in this paper. The effects of anodizing parameters, such as applied current density, concentration of NaOH and temperature of the solution on the formation, structure and surface morphology of the anodic films were also studied. The formation of the anodic film was analyzed by analyzing the anodic polarization curves, the potential-time curves and XRD, SEM graphs of samples obtained at different anodizing time. The results of corrosion resistance tests, XRD and SEM observation showed that the temperature greatly affected the formation and anti-corrosion property of the anodic film, but the concentration of NaOH not. The film with best anti-corrosion resistance was obtained at applied current density of 10mA/cm2, 353k in 1mol/l NaOH solution.

Jan 1, 2006

By R. W. Smith

The flotation response and electrokinetic behavior of Chlorella vulgaris and Chlamydomonas sp . when using dodecylamine hydrochloride as collector were studied in the absence and presence of Pb(I1). Also, an electron microscopy study was made of the algae after Pb accumulation. The flotation behavior of the organisms after Pb accumulation appears at least partially related to the location of the abstracted Pb onto or into the organisms.

Jan 1, 1991

By Gretel Parker

In situ Raman spectroscopic investigations of copper iron sulfides in leach solutions have been undertaken. Coupling potentiodynamic techniques to Raman spectroscopy produces a powerful tool for studying mineral surface response to changing conditions, while ESEM and high-vacuum techniques provide complementary ex-situ information on surface structure and composition. Oxidative acid leaching of chalcopyrite at ambient temperature yielded a product with S-S bonds that were shifted from those seen with covellite, with little evidence of elemental sulfur formation. Leaching of chalcopyrite led to non-homogeneous product distribution. Raman spectroscopy was able to identify the products formed on the mineral surfacein situ while leaching was occurring. Raman mapping and imaging demonstrated a surface distribution of the products which can be related to composition and structure changes of the mineral surface. The surface formed on chalcopyrite after anodic oxidation at 0.570 V vs. Ag/AgCl in 0.1 mol dm-3 HCl undergoes laser-induced transformation.

Jan 1, 2003

By Gerald M. Rich

Magma Copper Company, a subsidiary of Newmont Mining Corporation, has initiated many changes in the continuous casting of 5/16 inch diameter copper rod since startup of the San Manuel rod plant in early 1972. With rod production at forty percent over design capacity, many production records have been established including a record cast of 761 tons of salable rod in a twenty-four hour period. The most challenging and rewarding introduction was the continued utilization of an alloyed copper casting wheel in lieu of the conventional steel wheel. With proper cooling and careful control of the mold release agents. as much as 58.000 tons of copper were cast on a single copper wheel. Other advantages are: 1) Fifteen percent increase in available casting time 2) Reject rod from steel inclusions was reduced by nearly one-hundred percent 3) Wheel cost was decreased by ninety-one percent 4) Natural gas consumption dropped approximately fifteen percent 5) Large increase in refractory component life 6) Reduction of manhours/ton. Many other modifications have contributed to excellent rod quality and high operating efficiency. A two-piece launder was replaced with a single castable launder which reduced oxygen pickup and provided better slag removal. Modifications to the bar preparation unit, pickling system, and coiler resulted in considerably higher milling efficiency.

Jan 1, 1976

By Manoj Kumar, Vinay Kumar, Nikhil Dhawan, Manish Wadhwa

"Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.IntroductionThe electrical and electronic industries comprising computers, television, mobiles, etc, which are manufactured utilizing printed circuit, boards, capacitors, resistance, soldering material etc. During production, at the end-of service life and degradation due to the advanced version with latest features generate valuable metallic and non-metallic constituents. European Union Council on waste electrical and electronic equipment (WEEE) has classified these into different categories as listed in Table 1 [Streicher-Porte et al., 2005]. Among these the information technology, telecommunications and consumer equipment constitute electronic waste (e-waste) [EC, 2002]. Almost all e-waste consists of an integrated part of printed circuit boards which is a valuable source of several metals such as copper, tin, lead, aluminium, iron, silver, gold, platinum etc. [Relay et al., 1990]."

Jan 1, 2008

By Shize Jin

Effect of four polyols, namely ethylene glycol (EGL), glycerol (GCL), propanediol (PDL), butanediol (BDL) and three organic acids, namely oxalic acid (OA), malonic acid (MA) and succinic acid (SA) on the current efficiency (CE) and the cell voltage during zinc electrowinning was studied. Galvanostatic polarization was conducted in a supporting electrolyte (SE) containing 180 g dm-³ H2SO4, 60 g dm-³ Zn2+ and 8 g dm-³ Mn2+ at 38°C with magnetic stirring. The imposed current density was 50 mA cm-². The anodes were made of a Pb-Ag alloy and the cathodes were made of an aluminum alloy. The results showed that all the polyols tested in this study decreased the current efficiency and the cell voltage, but the decrease of the cell voltage was not important. Oxalic and succinic acids decreased the current efficiency to a less extent than the polyols, but did not decrease the cell voltage much. The only compound that increased the current efficiency was malonic acid, and its capacity of decreasing the cell voltage was the highest within the seven tested organic compounds.

Jan 1, 2003

By Erich Hovestädt, Hans-Jürgen Odenthal, Christian Wuppermann, Herbert Pfeifer, Antje Rückert

"During the argon oxygen decarburization (AOD) process high-chromium steel melts are decarburized by oxygen and inert gas injection through sidewall nozzles and a top-lance. Due to the large amount of the injected processing gas, low frequency oscillations of the vessel can be observed. It is suspected that these oscillations can influence the converter's structure. The exchange of forces between fluid and the surrounding vessel is the focus of this study. An oscillation model was developed and tested, one objective being to limit the computational effort which is necessary for fully coupled and time resolved CFD and FEM simulations. Experimental results obtained from water-model studies as well as from on-sight measurements are available and were used in order to validate the numerical results. The authors' intention is a contribution towards a more in depth understanding of the factors influencing vessel vibration during the AOD process.IntroductionDuring the last four decades the AOD process has been established as a reliable and efficient refining process in stainless steel making. The injection of process gases (O2, N2, Ar) through sidewall nozzles shows advantages in mixing effectiveness compared to other injection geometries e.g. bottom blowing [1]. Stainless steel grades contain usually more than 10% chromium. With decreasing carbon content during the decarburization periods the tendency of chromium oxidation increases according to the varying chemical equilibrium which depends on the partial pressure of carbon-monoxide (CO) in the gas phase. That's why oxygen is gradually replaced by inert gases, usually argon or nitrogen, in order to lower the CO partial pressure and thus to minimize chromium oxidation. Despite the high injection velocity of approximately Ma = 1, the kinetic energy of the gas jets is consumed within a short distance from the nozzle exits due to the large density ratio between gas and melt of approximately 1:8000. With increasing distance to the nozzle exit, the initial horizontal velocity of the gas jet decreases and due to buoyancy force motion of the detached bubbles turns into a vertical direction. Subsequently a gas plume develops with its typical conical shape described by various authors [1-4]. Due to the drag force between gas bubbles and melt also the liquid phase is forced into a vertical motion. Near the free surface and the wall regions the melt flow is deflected in different directions. Subsequently, the typical flow pattern in the AOD vessel arises, as sketched in Figure 1 and described in literature [5-9]."

Jan 1, 2012

By Christoph Sagadin

Corrosion mechanisms between high melting synthetic ferronickel slags and refractory were investigated. The used slags were prepared by mixing and melting of specific oxides. Substrates of the applied refractory material and specimens of FeNi slags were heated in a hot stage microscope up to 1650 °C. The experiments were performed under a defined gas atmosphere of 60% CO and 40% CO2. A further examination of the formed phases between slag and refractory occurred by scanning electron microscope. The investigations indicate that the slag penetrates between magnesia grains and partly dissolves magnesia. Spot analyses show that iron diffuses into the magnesia grains, which transform to magnesiawustite, meanwhile SiO2 forms different types of olivine like forsterite and monticellite. Thermodynamic calculations confirm the formation of these phases. The combination of practical lab scale experiments and thermodynamic calculations should finally contribute to an improvement of the refractory lifetime and performance.

By Feng Ningchuan, Guo Xueyi, Tian qinghua, Liang Sha

"In this study, copper adsorption by orange peel which was chemically treated with sodium hydroxide was investigated. The morphological and chemical characteristics of the adsorbent were evaluated by spectroscopy and N2-adsorption techniques. Equilibrium isotherms and kinetics were obtained and the effects of solutions pH, adsorbent concentrations and temperature were studied in batch experiments. Equilibrium was well described by Langmuir and Freundlich isotherms and kinetics was found to fit pseudo-second order type adsorptions kinetics. According to the Langmuir equation, the maximum adsorption capacities (qm) for Cu(II) was 50.25 mg·g-1 at pH 5.3. With the temperature increased from 16 to 60°C, copper removal decreased. The loaded adsorbent was regenerated using HCl solution and could be used repeatedly at five cycles with little loss of adsorption capacity. The results show additional chemical treatment of the adsorbent by NaOH, is favor of improving the adsorption capacity. Introduction Increased use of metals and chemicals in manufacture industries has resulted in generation of large quantities of effluent that contains high level of toxic heavy metals and it poses environmental-disposal problems due to its non-degradable, persistence nature and accumulation throughout the food chain [1, 2]. Copper is known to be a commonly used heavy metal. This metal, which found many useful applications in our life, is very harmful if charged into natural water resources and may pose finally a serious health hazard. Many methods, such as chemical precipitation, ion exchange, reverse osmosis and adsorption, etc., have been used for heavy metal ions removal from various aqueous solutions. In recent years, there has been considerable interests in use of biological materials including algae, bacteria, fungi, agricultural by-products and residues as adsorbents to remove toxic metals from aqueous solutions by adsorption [3-8]. Adsorption process has been extensively used to remove copper from aquatic medium using low cost adsorbents such as peanut husks [9], plant materials [10] and cellulose materials [11]. Among them, agricultural by-products and biomass are relatively cheap and show very high adsorption capacities. However, to apply untreated agricultural by-products as adsorbents has the disadvantages such as low adsorption capacity, high chemical oxygen demand (COD) and biological chemical demand (BOD) as well as total organic carbon (TOC), due to the release of soluble organic compounds contained in the plant materials such as lignin, tannin, pectin and cellulose, into the solutions [12-14]."

Jan 1, 2008