Search Documents

By R. Gampala

The consolidation of mom matrix composite monotapes occurs by the plastic (time independant) and creep deformation of monotape asperities. Past models of the process used seperate micromechanical analyses of the contact deformation by (rate independent) plasticity and power law creep (i.e steady state creep). These models are now used to simulate consolidation and to optimize/control consolidation process cycles so that the composite's microstructure is "steered" to, a user defined goal state. However, the models do not incorporate the sometimes dominant transient creep process and the instantaneous response of the plasticity mechanism causes finite discontinuities in the microstructure state vector field and therefore eliminates the possibility of using the powerful array of trajectory optimization schemes that all require continuous vector field for optimization and control. To overcome this problem, a inified creep/plasticity constitutive model that results in a continuous state vector field is used to rederive the contact deformation response during monotape consolidation. The contact blunting of a laterally constrained hemispherical asperity is first analyzed and its response represented by two coefficients; one relating the contact area to the blunting strain (C), the second, the mean contact pressure to the blunting rate (F).The C and F coefficients for this unified blunting problem are then obtained by finite element analysis, and detailed results presented for two composite matri-ces of topical interest (Ti-24A1-11Nb and Ti-6Al-4V).

Jan 1, 1996

By G. A. Brooks, R. W. Matusewicz, Nazmul Huda

"A computational fluid dynamic (CFD) model of a conventional tuyere blown slag fuming furnace has been developed in Eulerian multiphase flow approach. The model was developed by coupling CFD with kinetics equations developed by Richards et al. for zinc fuming furnaces. The model integrates submerged coal combustion and chemical reactions with the heat, mass and momentum interfacial interaction between the phases in the system. The model predicts the velocity, temperature field of the molten slag bath, generated turbulence, vortex and coal utilization behavior from the slag bath. The highest coal penetration distance was found to be at l/L = 0.2, where / is the distance from the tuyere tip and L is the total length (2.44m) of the modeled furnace. The model also predicts that 10% of the injected coal bypasses the tuyere gas stream un-combusted and carried to the free surface, which contributes to ZnO reduction near the free surface.IntroductionSignificant metal values are often discarded with slag in the form of metal oxide produced by the smelting industries. These metal values can be recovered from the slag by proper treatment. Zinc slag fuming is such a process, where a reductant source (usually coal) is injected in the molten slag bath to reduce dissolved ZnO from the bath into metallic zinc vapour. The process can be carried out in either conventional tuyere blown furnace or top submerged lance (TSL) smelting furnace. Conventional slag fuming processes are carried out on batch basis in a rectangular tuyere blown furnace. Approximately 50 tonnes of charge (either molten slag or solid slag) is fed to the furnace at the beginning of each fuming cycle. Two opposing sets of submerged tuyeres are employed to inject air and pulverized coal into the molten slag bath to carry out combustion and reducing reactions."

Jan 1, 2012

By Tullio Corsini

Scrap battery recovery process, developed by Engitec Impianti S.p.A., is improved transforming batches operations in continuous. Benefits expected: constant and better quality of the products; easier and more reliable control of the operating parameters, reduction of manpower requirements. Paste will content less sulfate, particularly in soluble form. Sodium sulphate is obtained with higher and constant purity.

Jan 1, 1993

By S. G. Kumar, R. G. Reddy

"Niobium aluminides offer the advantage of higher high temperature capability compared to other intermetallic aluminides due to the refractory nature of niobium. However, the reaction sequence in Nb-Al system is sluggish and currently there is a great interest in the processing aspects of these materials. In the present study, a systematic investigation was undertaken to compare the effect of different powder metallurgy processing routes on the phase relations and microstructure of 66Nb-22AH2Ti (in atom percent) alloy. The three different process routes adopted were: (i) cold pressing followed by reaction sintering; (ii) cold pressing and hot pressing followed by sintering; and (iii) arc melting, hydride-dehydride process to make the alloy powder followed by cold pressing and then sintering. The samples are analyzed by XRD, Optical Microscopy, SEM-EDS and EPMA. The analysis showed that alloy pellets made from pre-alloyed powders i.e., arc melting followed by hydride-dehydride process, gave good densification and more Nb3Al formation.1. IntroductionTo improve the performance standards of turbine engines, materials scientists are challenged to develop materials that have· high thrust-to-weight ratio with high specific strength, high specific modulus and good environmental properties at elevated temperatures. The conventional high temperature materials like nickel based superalloys are high in density and hence many of the high temperature materials scientists have focussed their attention on intermetallic aluminides like Fe-AI, Nb-AI, Ni-AI and Ti-AI in recent years. The phase relations and properties of alloys based on Fe-AI, Ni-AI and Ti-AI are fairly well known whereas little is known about the alloys based on niobium aluminides."

Jan 1, 1996

By Caisa Samuelsson, Fredrik Engström, Bo Björkman, Margareta Lidström Larsson

"Large amounts of by-products are generated by the Swedish steel industry each year. The EAF-process generates about 400 000 ton of slag, from which 80% is deposit. An alternative to deposit is to use slag as road construction material. However, metal content in the slag can be a problem, due to the leaching. The aim of this work was to investigate how stable these materials are when ageing and kept outside. Five different EAF-slags from domestic steel plants were used in this study. The materials were characterised after 0, 6, 12, 18 and 24 month to evaluate the ageing process. Scanning electron microscope (SEM), x-ray diffraction pattern (XRD) and a standard test for leaching were used. The changes in behaviour differ between the five materials. The total leachability decreases with time for all samples. CaCO3 is formed on slag surfaces as CaO reacts with moister and CO2 in the air. Introduction The slag generation in the Swedish steel industry is about 1.5 million tonnes annually, of which more than 500 000 ton is generated in EAF (Electric Arc Furnace), AOD- (Argon Oxygen Decarburization) converters and during the refining of steel in the ladle metallurgy. Some of the slags are used in different applications, but most of the steelmaking slags produced in Sweden are landfilled today. The chemistry, mineralogy and physical characteristics of slags make it a suitable material in construction, replacing for example, gravel and rock [1]. In some respects, in road construction, it may even be technically superior to virgin material. Slag from scrapbased steelmaking is used for road construction in Europe. The reason for the low utilization in Sweden is mainly due to potential leaching of harmful elements, legislations and competition with easily available natural raw materials. Except the potential leaching, the technical obstacles for not using some slags in construction include:"

Jan 1, 2008

By Kenneth A. Brunk

"This address discusses how ""Mineral Processing Technology"" can play a major role in the life and profitability of a mining company. Examples of past and present technological breakthroughs and their impacts will be examined. Also, the future of processing technology will be emphasized.IntroductionThis talk will center on the role of technology as an important component of a business plan for mining companies. I'll attempt to explain how I see technology development as an underpinning of a successful mining company. We will examine an example of a technology that has resulted in a re-birth of segments of the industry, examine a technology life cycle and discuss technology as it relates to ore reserve replacement. Also, we will touch on technology in today's mining company and propose some food for thought for those designers of corporate organizations."

Jan 1, 1997

By Ivanildo Hespanhol

"DALYs are a measure of the health of a population or burden of disease due to a specific disease or risk factor. It evaluates the time lost because of disability or death from diseases compared with a long life free of disability in the absence of disease. DALYs are calculated as the sum of years of life lost by premature mortality (YLL) and years of healthy life lost in states of less than fully health, i.e., years lived with a disability (YDL), which are standardized by means of severity weights, thus: DALY=YLL+YLD.WHO has established for wastewater use in irrigation (1) the same reference level of health protection as established for drinking water quality (2), i.e., the additional burden of disease from consuming water irrigated food should not exceed 10-6 DALY(Disability-Adjusted Life Years) loss per person per year (pppy). This level of risk means that a single additional case of disease may occur in a population of 1 million, during a life time (70 years). In a individual basis is equivalent to the occurrence of a mild disease during about 31,5 seconds.Such a restrictive risk is almost impossible to be attained in most developing countries which may not be able to afford the cost of wastewater treatment and of other protective measures, even for restrict irrigation.This paper presents proposals to adapt the reference level of risk to local technical, cultural, economical and social conditions of developing countries on the basis of a risk benefit approach."

Jan 1, 2008

By J. M. Floyd

"Top submerged lance furnace developments started in CSIRO in the early 1970s and was given the name Sirosmelt. In the early work the technology was developed for tin smelting and processing tin slags but once a small pilot plant was established other slag processing applications were soon recognised and evaluated for various copper, nickel, zinc and cobalt-containing slags. The process was tried for copper smelting and converting, which was proven in the small pilot plant in 1978. In the same year the first commercial application of the technology was established for the recovery of tin from slags at Associated Tin Smelters, Sydney. Work on lead smelting was initiated by the CSIRO team in the late 1970s and laboratory work led to pilot plant trials by Mount Isa Mines.In the second decade of the technology the focus of development became commercial acceptance of the technology through marketing, development and application by Ausmelt and Mount Isa Mines; the former commercialising and developing the technology for a wide range of applications, while the latter concentrated on its own commercial needs of copper and lead smelting. This decade saw a number of commercial plants built in Australia, with considerable interest becoming evident from other parts of the world. Towards the end of this decade Mount Isa also entered into the business of marketing of the technology through rights dating to the joint work with CSIRO in the late 1970s.So far, after five years, the third decade of the technology has been characterised by diversification of applications of the technology to areas outside the non-ferrous and precious metals production industry. The waste processing and recycle industry and the iron and steel industry have recognised that the top submerged lancing system is a new type of reactor with many significant features which provide new opportunities for processing a range of materials under good environmental controls in a cost effective manner.I hope this audience will excuse my boldness in talking about the third decade of the technology when we are only half way through! I am aiming in this paper to not only talk about the past, but to try illustrate the future directions which I envision."

Jan 1, 1996

By Merete Tangstad, Lars Klemet Jakobsson

"Slag refining is a promising refining method for boron removal from silicon as a part of a metallurgical route for production of silicon for solar cells. There is, however, limited data on the distribution of impurity elements between silicon and different types of slags. In the present study, the distribution of boron and calcium between silicon and slag were determined at 1600 °C for calcium silicate slags with a CaO/SiC>2 ratio between 0.65 and 1.3. An almost horizontal linear trend was found for the distribution of boron between silicon and slag, and the borate capacity was found to follow the relationln(CB0, ) = 30.8 + 2.96-V (1)where V\s the CaO/SiCh mass ratio within the range of the experiments.IntroductionSolar grade silicon feedstock contributes significantly to the total cost and energy required to make crystalline silicon solar cells. A less expensive and less energy requiring method of solar grade silicon production is therefore needed in order to make crystalline silicon solar cells more viable as an energy source. Silicon is an abundant element and the manufacturing cost of solar grade silicon is therefore mainly determined by costs related to purification of metallurgical grade silicon. The Siemens process is the most common process today, but it is an expensive and highly energy requiring process that gives silicon with a higher purity than is needed for crystalline silicon solar cells. A cheaper and less energy requiring method for production of solar grade silicon can either be achieved by modifying the Siemens process or by using a new production method. Purification of metallurgical grade silicon through a metallurgical route is a promising method that is already in use industrially. It has however proven to be hard to lower the boron content to 0.3 mg/kg or less, which is the requirement for most p-type crystalline silicon solar cell manufacturers. Slag refining is seen as one of the most promising approaches that can be used to bring down the boron content to the required level, but there is not much data on how boron is distributed between silicon and binary calcium silicate slags [1-4]. The distribution of boron between silicon and calcium silicate slags at 1600 °C has been studied in this work, and the obtained data has been used to calculate the borate capacity of binary calcium silicate slags."

Jan 1, 2012

By T. V. Jayaraman, Kranti Kumar, Paul Praveen J., Dibakar Das, A. R. James

"Lead free piezoelectric ceramics with high piezoelectric coefficients are in great demand for sensor and actuator applications. Synthesis and characterization study of one such lead free system, barium zirconate titanate - barium calcium titanate [xBZT-(1-x)BCT] (x = 0.5), via solgel method have been carried out. X-ray diffraction (XRD) and transmission electron microscopy (TEM) confirmed the formation of single phase BZT-BCT nanoparticles (<50 nm). The as-synthesized powders were calcined at 1000°C and the powders were pressed into cylindrical pellets. Solid-state sintering of the green pellets at 1550°C for 2 hrs resulted in single phase perovskite structure. Hysteresis loops were obtained which indicates the ferroelectric nature ofBZT-BCT. The bulk ceramic samples with the highest sintered density (~93%) were subjected to electrical poling and the piezoelectric properties ( d33, kp, & i:,) were measured. The structure and piezoelectric properties were investigated and correlated for the given composition of the BZT-BCT system.IntroductionPiezoelectric ceramics are widely used in various sensors and actuators and most of the piezoelectric ceramics, which are presently used, are lead based, which contains at least 60% lead (Pb) by weight. The critical disadvantage of these lead based piezoelectric ceramics is their hazardous effect related to the toxicity of lead, which poses a serious environmental concern starting from their processing to the disposal stage[l]. It is well known that a material to be a good piezoelectric it requires a morphotropic phase boundary (MPB) i.e. the composition induced phase transition between any two ferroelectric phases."

Jan 1, 2013

By N. Moelans

A method using an ex-situ electrochemical measurement device was developed to determine the oxygen potential of non-ferrous metallurgical slags. The electrochemical cell consists of the molten slag sample, an inert Ir electrode, a stabilized Zr02 solid electrolyte and a NiINiO reference electrode. Different slags from non-ferrous pyrometallurgical processes were analysed at 1100 and 1200°C and pO2 values between 10-3 and 10.12 bar were obtained. The measurements were evaluated with? thermodynamic calculations and using processing considerations. It was found that the reproducibility and stability of the measurement was significantly improved by shielding the molten slag from the atmosphere by a thin layer of carbon, especially for slags with a low oxygen potential.

Jan 1, 2003

By Jacob Bummer, Greg Roset, Dayle Flynn

"IntroductionStillwater Mining Company operates a Precious Metals Smelter (PMS) located in Columbus, Montana USA. The PMS processes iron, copper, and nickel sulfide bearing concentrates containing platinum, palladium, gold, and rhodium. The concentrates are produced from two mines in the Beartooth Mountains located in south central Montana. The PMS utilizes a 7.5 megawatt 3-in line electric furnace to smelt the concentrates, and two Top Blown Rotary Converters (TBRC's) to remove iron. In addition to the mine concentrates, the PMS also processes various forms of Platinum Group Metal (PGM) bearing recycled catalyst. The sulfide matte produced within the electric furnace and TBRC's acts as a collector for the PGMs. Throughout the operation of the PMS, there are three different forms of molten material that are processed through the Stillwater Granulation system: TBRC matte, TBRC slag, and electric furnace matte. This paper describes the operation of this granulation system.Tapping the FurnaceWhen a sufficient level of molten PGM bearing matte has been reached within the inner volume of the electric furnace, the molten material is ""Tapped"". Tapping requires drilling into the electric furnace until reaching the molten matte phase. The matte phase will drain out of the drilled hole through a graphite launder into a 5 ton refractory lined ladle. Once the ladle is full, the tap is plugged with a mud gun."

Jan 1, 2012

By E. A. Chavarriaga, L. J. Jaramillo, O. J. Restrepo

"This paper presents the results of the manufacturing ceramic pigments with spinel structure, using methods of synthesis of low temperature. In this work we obtained spinel structures type by the methods of Self-combustion, Coprecipitation, Microemulsion, Gel citrate and Pechini. These methods become an attractive alternative to traditional method (ceramic method), since we can work at a lower temperature, reducing manufacturing costs, lower fuel consumption, less wear on equipment and other environmental and economic implications. Also it is possible to have control over features such as stoichiometry, morphology of the products, reaction times and structures. The products obtained by these routes will be used in the manufacture of ceramic pigments and characterized using different techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and UV-VIS spectrophotometry.IntroductionSpinels are ternary oxides AB204, where A and B are cations occupying tetrahedral and octahedral positions respectively. These oxides exhibit interesting electrical, magnetic and catalytic properties [1-4], depending on its nature, charging and intrinsic distribution of ions [5].The most widely used method to prepare spinels has been through solid state reaction, which consists of mixed oxides at high temperatures [6, 7]. In the last years, there have been a strong tendency to use chemical routes for the synthesis of crystalline ceramic particles at low temperatures [8,9]. Unconventional methods currently employed for the synthesis of complex oxides are Gel citrate method, Pechini, Spontaneous combustion, Microemulsion and Coprecipitation. Pechini method [10, 11], based on polymeric precursors, does not require high temperatures and allows stoichiometric control for greater reproducibility. This method involves the formation of a polymeric resin between a metal quelate and polyhydroxy acid of alcohol by polyestirification.Coprecipitation is important for many environmental problems related to water resources, including acid mine drainage, migration of radionuclides in waste repositories dirty, transport of contaminant metals in the industry, metal concentrations in aqueous systems and the technology of wastewater treatment. The coprecipitation process can vary in each case; the partition in the solid phase can be carried out by surface adsorption, ion exchange, surface precipitation, occlusion and formation of solid solution. The formation of solid solution is the result of structural incorporation of the marker in structural support sites resulting in a minor component in the solid solution with the host phase that has a very low solubility of pure solid [12]. Synthesis by gel citrate method allows the use of a route to obtain ceramic pigments from a very simple experimental system in which the stoichiometric control, the size and shape of the particles and the purity of the phases obtained can be controlled more accurately [13]."

Jan 1, 2012

By Suguru Kohno, Yoshihiro Momose, Masakazu Honma, Tokirou Kamosawa

Copper metal surfaces have been examined by an extremely sensitive surface analysis technique called temperature programmed photoelectron emission (TPPE). The surfaces were ultrasonically cleaned and subsequently abraded by a screw in organic solvents and water. The TPPE apparatus is composed of a Geiger counter with Q gas (He+ iso-C4H10). The curve of photoelectron emission (PE) intensity vs. wavelength from 300 to 170 nm, termed PE spectrum, was repeatedly measured at different temperatures in the temperature- increase process from 25 to 350°C. The number of emitted electrons in a PE spectrum (PE total count) increased, reached a maximum at-250°C, and decreased with increasing temperature. With the surfaces cleaned alone in the liquids the maximum PE total count decreased in the order C3H70H > (CH3) 2CHOH > C2HpH > CHPH > H2O. With the mechanically abraded surfaces in the liquids the maximum PE total count changed as a function of the abrasion period and the maximum tended to appear at higher temperature with increasing abrasion period; the maximum value at 10-min abrasion decreased in the order H2O > CHpH > C2HPH > (CH3) 2CHOH > n-C3HpH. It was suggested that the TPPE behavior can be related to the acid-base interaction between the alcohols and the abraded metal surfaces and the presence of a contaminant over layer on the surface. From the XPS analysis of the 01 s spectra it was suggested that the chemical change of the adsorbed oxygen to oxide oxygen with temperature plays a substantial role in the appearance of the maximum PE total count.

Jan 1, 2000

By Osarnu Inoue

In Mitsubishi Continuous Copper Smelting and Converting Process, smelting, slag-matte separation and matte converting are continuously carried out in series in three furnaces connected by launders. As a result of this operational configuration of the furnaces, influence of the change in operating condition in upper stream, such as variation of feeds in the smelting furnace, propagates to down stream with some delay. In order to achieve stabler operation, process control algorithm based on the dynamic characteristics of each furnace would be very effective. In this study, the dynamic process simulation model was developed for the smelting furnace. The model consists of two mathematical modules, i.e. the thermodynamic module and the mixing module. The calculation results using operating data obtained at Naoshima Smelter showed good agreement with the actually observed change in temperature, composition and flow rate of matte and slag at the outlet of the furnace. In addition, operation parameters such as reaction efficiency of oxygen and coal, dead volume of melts were estimated.

Jan 1, 1999

By LeRoy C. Prichard

The scrap based steel producers in the United States generate an estimated 650,000 tons of electric arc furnace (EAF) dust annually which is classified as hazardous waste, K061. These scrap based producers commonly referred to as mini-mills represented 39% of the steel produced in 1994. Based upon the EAF plants being installed or planned today, it is a reasonable projection to anticipate 50% of the steel produced in the United States will be by EAF&apos;s. Using a straight line projection of percent of steel produced to tonnage of EAF dust generated, this will result in 833,000 tons of dust being generated upon the completion of these new EAF producing plants, presumably by the year 2000. Because the United States is a capitalistic economy, a steel producer is in business to make a profit therefore dust management becomes a very important variable in the cost of making steel. An EAF mini-mill dust management program must consider at least three components. First the handling of the dust must be in accordance with the law; i.e., the Environmental Protection Agency rules and state and local municipalities guidelines governing K061. Second, it must be an economical solution that allows a company to manage its dust processing costs, a component of its total steel production costs while producing steel at a profit. Third, the dust management program should be one that is environmentally responsible; viz., the program should reclaim or recycle the dust constituents, as feedstock materials or saleable products. The first component, obedience of the law seems to be a relatively straight forward, common sense objective; however, as nearly every mini-mill operation will testify it has been a area of changing laws with confusing variations when it comes to K061. Even more frustrating is the fact that obedience or compliance today does not mean that the company will be considered law abiding in the future.The liabilities associated with

Jan 1, 1995

By N. J. Tannyan

Laboratory bath smelting tests were conducted to determine the feasibility of smelting nickel- copper concentrate directly to a low iron matte in one step. Concentrate, air/oxygen and a silica flux were fed to a matte-slag bath kept in MgO crucibles at I 300°C. Various oxygen enrichments and smelting rates were used to maintain 0.5 to 2 wt% iron in the product matte. The slag losses are comparable to those obtained under similar industrial conditions. Due to the highly oxidizing conditions required to produce mattes with low iron contents, it is not recommended to target iron contents below about 2% in the matte. The specific bath smelting rates were equal to or higher than those in various industrial bath smelting processes.

Jan 1, 2003

By P. Chris Pistorius

"Use of coke in blast furnace ironmaking is the main origin of carbon dioxide emissions from integrated steelmaking. Use of pre-reduced iron feedstocks would reduce the coke rate and, if pre-reduction were carried out with natural gas, would decrease the overall carbon intensity of ironmaking. Blast furnace productivity would also increase, because the blast volume per unit of hot metal would decrease. This paper shows that these trends can be predicted quantitatively, by using a conceptually simple Rist-style blast furnace mass and energy balance, assuming furnace productivity to be limited by the tuyere gas flow rate. Such predictions would assist in optimizing the choice of the degree of reduction and relative amount of pre-reduced blast furnace feed.IntroductionSteelmaking is responsible for some 5% of world CO2 emissions, at a rate of approximately 1.9 tonnes of CO2 per tonne of cast steel [1]. In integrated steelmaking, the ultimate source of most of the CO2 emissions is coke, the indispensible (and expensive) fuel and reductant for blast furnaces. There are several research programs underway worldwide which seek to lower the carbon intensity of ironmaking; one of the largest is the European ULCOS program [2], in which the main proposed change to blast furnace ironmaking is to scrub CO2 from the furnace off-gas (for possible sequestration), recycling the remaining gas to the furnace. To limit the recycling nitrogen load, oxygen rather than air is used to combust coke.A conceptually simpler approach is to charge prereduced feed (direct-reduced iron) to the blast furnace. This approach has been used for some two decades at the AK Steel Middletown plant, where some 200 kg of direct-reduced iron (DRI) is charged per tonne of hot metal [3]. The Middletown blast furnace has exceptionally high productivity (rate of iron production relative to the furnace hearth area), simply because less coke is required per ton of hot metal if part of the feed is already metallic. Midrex [4] has provided some quantitative predictions of the implications of DRI use in the blast furnace, stating that for every 10% of Fe in the feedstock that is in metallic form, the fuel requirement decreases by 7% and the productivity increases by 8%."

Jan 1, 2012

By M. Tamura, K. Fujita, K Shinozuka, H. Daimon, H. Esaka

"In-situ observation of unidirectional solidification using transparent substance has been performed to investigate the growth direction of solid phase. Cell or dendrite of which preferred growth direction is not parallel to the heat flow direction was observed with various solidification conditions. Dimensionless growth direction (p) changes from 0 to 1 with increasing growth velocity at a constant temperature gradient. Introducing the dimensionless growth velocity, the relation between p and growth condition could be correlated.IntroductionTransition in macroscopic solidified structure from chill to columnar zone which is found in normal castings takes place via grain selection1). Cast products such as turbine blades are unidirectionally solidified, grain selection plays an important role to choose suitable crystals which have reasonable orientation in the region called ""starter"", which is a very initial part of casting2). Therefore, grain selection is a very important process in the formation of casting structure. The present authors have been studying on the process of grain selection using succinonitrile, which is a transparent organic substance and have found that the growth distance necessary for grain selection depends upon the solidification condition3-5). When the solid/liquid interface is dendritic, the grain selection occurs quickly. On the other hand, when the solid/liquid interface is cellular, it occurs slowly. We supposed that the growth direction of dendrite is different from that of cell when the substance is unidirectionally solidified. Indeed, Kurz and Fisher wrote in their text book that dendrite grows along its preferred growth direction, <100>, regardless of heat flow direction and that cell grows along heat flow direction regardless of its preferred growth direction1). However, there is no quantitative description about the growth direction when the solid/liquid interfacial morphology is cellular. Furthermore, there have been little works6) to study the growth direction of cell and dendrite."

Jan 1, 2000

By H. Masuda

The lijima Zinc Refinery started operation in 1972, and has today an annual capacity of 200, 000+-Zn. The hematite process was employed for the first time and the ideal of waste-free refinery has been pursued for 30 years. In recent years, however, only half of the hematite produced would be sold to the cement industry and hence a reduction of arsenic level has been necessary in order to sell the entire amount produced, The arsenic cementation process with zinc powder, developed through a long time laboratory research was found among some options as the best for the hematite process. The construction work started in 2000 and the facility was put into operation in 200 I. As a result in the same year all hematite were sold to the cement industry. The outline of this project, present operations and technical issue are reported in this paper.

Jan 1, 2003