Search Documents

By Takahiro Miki

Soldering material widely used is Sn-Pb alloy, which have low melting point and excellent electrical, strength properties and wettability. However, Pb is one of the toxic elements, which is undesirable due to environmental and safety reasons, thus Pb-free alternative alloy is preferred for new soldering materiaL Sn-Ag and Sn-Zn based alloys have been viewed as very promising candidates, among many potential substitutes. Addition of third element to these alloys will decrease melting point of the alloys. Hence, Sn-Ag-In and Sn-Zn-Mg alloys are expected to be suitable for replacing Sn-Pb solder alloy. In order to dcsign new Pb-free soldering materials, it is crucial to understand precise thermodynamic properties and phase diagrams of alloy systems. In the present work, ion current ratios of Ag to In and Mg to Zn were measured for Sn-Ag-In and Sn-Zn-Mg alloys by mass spectrometry, respectively. Also, the authors reviewed the thermodynamic properties of terminal binary alloys determined by other researchers and evaluated a thermodynamic functions to express the excess Gibbs free energy of each binary alloy. Thermodynamic functions to express the excess Gibbs free energy of liquid Sn-Ag-In and Sn-Zn-Mg ternary alloys were determined, utilizing the assessed Gibbs free energy of terminal binary alloys with the measured ion current ratios using mass speetrometer.

Jan 1, 2003

By Y. Maeda

Non-ferrous smelting furnaces generally install a gas cooling system for treatment of waste gas containing SO2,. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system is the best way to cool gas, however this system requires high initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled jacket system, are more suitable if the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In additton, the water-cooled jacket system is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace was planned in our factory and it was necessary to install waste gas cooling equipment. In our case, a water-cooled jacket system was more feasible because of the low gas volume and high dust content. It was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cooled jacket had been experienced in the past. That is because SO2 In the waste gas changed into sulfuric acid which corroded the jacket material. As the first step, several data from actual' usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled jacket system was newly designed and tested for three months in a pilot plant. After this system's performance was confirmed, it was installed in a new furnace as a commercial plant. After one year of operation, the initial thickness of carbon steel jacket remains almost the same.

Jan 1, 1992

By Alhondra de los Santos, Jesús L. Valenzuela, Jose R. Parga

"The present study evaluated the feasibility of using iron species generated by electrocoagulation (EC) as an adsorbent for removal As(III/As(V) from aqueous media. The full potential of EC was evident in that more than 99 percent of arsenic was removed without addition of chemical reagents. The adsorbent iron-species generated by EC was characterized by Chemical Analyses, X-Ray Diffraction and Scanning Electron Microscopy. The experimental data were correlated by employing a Langmuir adsorption isotherm. Thermodynamic parameters such as ?H o , ?S o and ?Go were calculated. The adsorption process was found to be exothermic and spontaneous.1. IntroductionArsenic contamination in potable water supplies is a serious health problem in many countries around the world. Groundwater arsenic contamination in La Comarca Lagunera Mexico was first reported 30 years ago [1]. Arsenic concentration has been found in well water from several communities ranging from 0.25 to 1.0 ppm. The elevated concentration of arsenic in water, above that originating from natural sources, has been attributed to the use of organoarsenical pesticides in the cotton fields and also to the millions of tons of waste slag generated at a local lead smelter [1]. The main arsenic species present in natural waters are arsenate ions 3- 4 AsO (oxidation state V) and arsenic ions H3AsO3, - 2 3 H AsO and 2- 3 HAsO oxidation state III). However, As(V) ions are most prevalent in oxygenated water while As(III) is found for anaerobic conditions, such as in well water or in groundwater. Conventional methods of arsenic removal rely on chemical-based treatment with lime, alum coagulation, iron coagulation and chemical oxidation. Other processes used with varying degrees of success include adsorption onto activated carbon, reverse osmosis, nanofiltration, manganese dioxide, magnetite and ionexchange resins [1-3]. These conventional processes generate a considerable quantity of secondary hazardous waste such as solid sludge, which also pose serious environmental problems. These drawbacks have forced various industries to search for effective, alternative treatment technologies for arsenic with a preference for electrochemical methods."

Jan 1, 2008

By Luben Xie, Lin Hu, Qiang Wang, Min Gan, Tao Jiang, Wenqi Li, Yi Wang, Xiaohui Fan

"The mineralization behaviors of typical fluxes are studied by investigating the microstructures with optical microscope. The results show that the reactions begin with between iron ore and lime, limestone with small particle to form primary liquid. Then coarse limestone, dolomite and serpentine take part in reaction under the action of primary liquid. Limestone is the easiest to mineralization, next dolomite, and the last is serpentine. The higher basicity and smaller fluxes size favor the mineralization process of dolomite and serpentine.IntroductionThe purposes of adding fluxes into sintering are that:(1) to increase the basicity of sinter, so as to reduce even eliminate addition fluxes into BF(blast furnace) and decrease the coke ratio of BF[1,2]. (2) to decrease the melting point of sintering mixture to ensure sintering can be carried out at a lower temperature and reduce the energy consumption. (3) to improve the qualities of sinter by forming binding phase with iron ore fines [3].Flux is another significant component for sinter besides iron ore, especially for high basicity sinter[4]. The proportion of flux is usually higher than 10% in sinter mixture(excluding return mine).There were many reports about the influence of the flux types on sintering, such as limestone, dolomite, lime and so on[5-7]. It is very important to choose suitable fluxes for iron ore sintering. Although the effect of flux size on sintering also has been researched, the mineralization behaviors of the fluxes in the sintering process has not been illuminated. The paper will study the mineralization behavior of fluxes in sintering."

Jan 1, 2011

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997

By Giuseppe Granata

An innovative process using titanium tetrachloride (TiCl4) gas as reactant has shown successfully to obtain titanium through electro-winning of TiCl2 formed in-situ on titanium cathode. The process involves a continuous feed of TiCl4 gas reacting onto a titanium cathode immersed in a molten salt (NaCl-KCl), whereby in-situ formation of titanium dichloride (TiCl2) through a disproportion reaction. Simultaneously, the TiCl2, thus in-situ formed in the molten salt media, has been reacted into chlorine gas and titanium, the latest electrodeposited on the titanium cathode by electrowinning. The reaction kinetic of this innovative process was investigated in terms of TiCl2 in-situ formation rate and galvanostatic electrodeposition rate, where, in particular, the effect of operating variables such as TiCl4 partial pressure and flow rate, as well as temperature and galvanic potential applied was investigated.

Jan 1, 2014

By N. El-Kaddah, J. W. McKelliget

"A mathematical model for the analysis and design of hybrid plasma reactors for advanced materials synthesis is presented. The model is based upon a solution of the electromagnetic vector potential equation and is capable of predicting the two-dimensional velocity, temperature, and electromagnetic fields as well as the reaction kinetics inside the reactor for any axi-symmetric coil configuration. The model is used as a computer aided design tool for the design of hybrid plasma reactors consisting of a conventional DC torch augmented by an RF induction coil and it is demonstrated that the hybrid system possesses superior characteristics for materials synthesis over conventional DC or RF systems. The coupling between the RF and DC components is found to affect both the temperature field and the flow field and to have a significant effect on the reaction kinetics and on materials recovery. The model is used to study the thermal decomposition of silicon tetrachloride as a function of reactor design and operating parameters and it is demonstrated that through a CAD approach it is possible to significantly improve the operation of materials synthesis systems.IntroductionIn recent years there has been growing interest in the use of the inductively coupled plasma for chemical synthesis as a way of meeting the increasing demand for high quality, high performance materials for use in critical applications/l/. Although the basic feasibility of this approach has been demonstrated in the laboratory/2,3/ there still exists a number of operational problems that adversely affect system performance for some applications. In particular, the recirculation and back flow effects that arise from the electromagnetic forces in the plasma can result in the repulsion of the reactants from the hot plasma core and their subsequent deposition on the walls of the reactor. Another operational problem arises from the fact that the energy dissipated in the plasma has to compensate for the heat losses to the environment by conduction, convection, and radiation in order to maintain the ionization of the plasma and, hence, the stability of the plasma may be affected by the presence of the reactants and their products."

Jan 1, 1988

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In order to produce good quality ammonium paratungstate, Sn needs be removed efficiently from the tungstate processing solution. The nascent hydrous ferric oxide has excellent adsorption ability and is often used as an adsorbent to remove metal ions from aqueous solution. In this paper, nascent hydrous ferric oxide is used to remove Sn from tungstate solution. Through experimental, the effects of pH value, reagent amount of adsorbent, reaction temperature and reaction time on the Sn removal are investigated. The study shows that 98% of Sn can be removed effectively from sodium tungstate solution and only 2% of W is lost during process under the conditions of pH 9~12, reagent amount of Fe addition 40 times Sn amount, reaction time 30min and room temperature. As the Fe addition reaches 90 times of Sn concentration in the ammonium tungstate solution, 99% of Sn is removed and APT with zero level purity national standard is obtained.

Jan 1, 2014

By Jean-Christophe Gebelin, Mark Jolly, Samantha Jones

"The de-waxing process in investment casting is truly a black art which is carried out in a black hole - the autoclave. The process involves exposing wax, coated by a porous ceramic shell, to steam at a pressure of 10 bar and a temperature of about 180°C. The processes which then occur are truly multi-media and multi-physics. Steam condenses in the porous ceramic, wax melts and flows, the shells expand and sometimes crack. Why the shells crack is one of the most difficult questions asked in the industry.Modelling and validating the de-waxing process is not simple. The IRC at the University of Birmingham is attempting to model this process using Physica+ a code developed in the UK. This paper will present the latest results in this attempt to model one of the casting industries most intractable problems.IntroductionThe de-waxing process using an autoclave involves the following physical phenomena:· Flow of the steam in the autoclave;· Heat transfer from the steam to the wax, possibly through the shell;· Melting and flow of the wax.At the same time, other phenomena may occur, such as the flow of the steam through the shell, the condensation of the steam on the shell surface and on the wax pattern surface, the flow of wax the through the shell, etc ...This shows how complex the de-waxing process is from a physical point of view. The main defect that appears during this process is the cracking of the shell. Previous modelling work carried out by Snow [1] has shown that it is possible to predict the stress in the shell, making numerous assumptions. In this paper, the modelling to predict the state of stress in the shell that is currently in development at the University of Birmingham is presented together with the presentation ofthe physical phenomena to model and the assumptions used. The parameters that are needed in such models will also be discussed, and some experimental work undertaken at the moment presented."

Jan 1, 2001

By Shengqin Zhang, Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery, Amr Abdelghany

A novel ironmaking process is under development at the University of Utah aimed at producing iron directly from iron oxide concentrate in a flash reactor. This process will reduce hazardous emissions and save energy. The kinetics of magnetite reduction with hydrogen was previously investigated in our laboratory in the temperature range 1150 to 1400 oC at large temperature increments (~100 oC increments). Due to the significant melting that occurs above 1350 oC, the reduction kinetics was measured and analyzed in two distinct temperature ranges of 1150 to 1350 oC and 1350 to 1600 oC (~50 oC increments). Experiments were performed using magnetite concentrate particles of different sizes under various hydrogen partial pressures and residence times. Reduction degrees of more than 90 % were achieved in a few seconds at temperatures as low as 1250 ºC. Different rate expressions were needed to obtain reliable agreement with experimental data.

Jan 1, 2016

By Tengfei Qi, Liqiang Fan, Huiqing Tang

A new method to process the oolitic high phosphorus iron ore for phosphorus removal has been proposed in this research. It is an integration of direct reduction and melting separation with carbon-containing pellets prepared using biomass char. Experiments of direct reduction were preceded using a tubular furnace and three parameters were investigated and they were reduction temperature, biomass char adding ratio(molar ratio of carbon to oxygen） and atmosphere. Results show that the optimum condition is of reduction temperature is 1373 K, biomass adding ratio 0.9, PCO2/PCO 1.0 and reduction time 15~25 min. Under this condition, the reduced briquettes with a metallization of 75.0~80.0 % and a residual carbon content of 0.69~0.11 wt% could be obtained. Subsequent melting separation experiments were conducted using a Si-Mo high temperature furnace. Results show metal with phosphorus content of about 0.4 mass% could be obtained from the reduced sample.

Jan 1, 2015

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the ,process, to the subsequent cleaning of the gas and to the use of the heat extracted from the gas. The method of reducing the effect of acidic ,sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms are discussed. The development of indirect recuperators using air, water or steam cooling, made 'possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process conditions".

Jan 1, 1992

By John Wallace

"Monitoring compound semiconductor crystal growth using multifrequency eddy currents for sensing illustrates some of the extreme problems of measurement and interpretation that are not often seen in metallic systems. Using sensor arrays and scanning sensors have produced a qualitative and quantitative understanding of some of the high temperature electrical conductivity mechanisms in several compound systems. A detailed review of the CdTe/CdZnTe data is presented showing some of the complexity in the data as opposed to what is found in elemental semiconductors.HistoryThe most common goal in the use of eddy current measurement in crystal growth is to deter-mine the curvature of the liquid solid interface during growth to test if the heat transfer estimates of the thermal design were adequate for single crystal growth[l]. This aim could be met but represented only a small fraction of the data that was produced observing a growth cycle. A secondary consideration was what could be discovered in the recorded data about the growth and subsequent heat treatment as the boule cooled. This is usually a more difficult task because a crystal growth process is not a controlled experiment so much as a process that continually sees modification. Using a sensor arrays or a scanning loop has produced a qualitative and quantitative basis for understanding some of the high temperature electrical conductivity mechanisms. The implication of the these measurements of electrical conductivity variations are important in that they reflect the complex defect states that will occur on cooling and heat treatment following crystal growth. In contrast to the complex behavior of the conductivity of these compound semiconductors in the solid and liquid state we have the very well characterized system silicon to compare. Initially the interest on using eddy currents to monitor compound semiconductors came from G. Westphal at the Texas; Instruments Company in 1987 to monitor aspects of growth and compounding of GaAs. This was followed by work on solution growth of HgCdTe with D. Witter. The initial interest in the use of eddy cur-rents for monitoring CdTe crystal growth came from Prof. Wilcox at Clarkson University in the practical interest to determine and control the crystal interface curvature during vertical brigdeman growth. The first actual work was done by one of his former students. G. Neuge-bauer at the II-VI Corporation which was carried on by G. Rosen at Clarkson and R. Shetty at II-VI Corporation and with A. Socha at Johnson-Matthey Electronics. The work on CdTe extends over four years and yielded sufficient data to allow one to evaluate the utility of the information produced as compared to what could be obtained from monitoring an elemental semiconductor such as silicon."

Jan 1, 1997

By Manfred Schmidt

Realizing an invention of Professors Queneau and Schuhmann, Lurgi GmbH has developed a radically new lead smelting technology, which was demonstrated on a ?30,000 tpy scale at Berzelius Metallhiltten GmbH between 1981 and 1986. Designed to treat all grades? of lead concentrates as well as complex secondaries, the novel QSL-Process applied one bottom-blown, refractory-lined long reactor and comprises two basic steps: Continuous oxygen smelting of the green charge is followed by continuous carbothermic slag reduction. Four firm orders and a number of serious inquiries from major lead producers confirm that the QSL-technology has convinced the industry of inherent process advantages. These include low investment and operating costs, flexibility and environmental acceptance. In the fall of 1986 Cominco Ltd. decided to erect a 120,000 tpy QSL plant at the site of the Trail lead smelter. Feed materials will consist of lead concentrates and zinc leach residues. The designed QSL reactor has a total length of approx. 41 m, and working diameters of 3.74 m for the oxidation section and 3. 24 m for the reduction section .. Separate gas offtakes on both sections will enable to? reduce the sulfur dioxide gas volume, and to recover a mixed zinc-lead oxide fume. Operation of the QSL reactor will start end of September 1989. First results will be presented.

Jan 1, 1990

By E. Salinas R.

This work is related with a whole characterization of cantera stone, to establish its characteristics that can give it an additional value for the reuse and reutilization of dust, slurries and small pieces of stone which can be treated as wastes. The obtained results reflects that the residues studied can be used as substitutes of feldspars in the production of pieces of ceramic, and also in the elaboration of paints for the same pieces according to the mixes that can be made with the variation of Na2O, CaO and K2O. According to the humidity proofs and specific gravity done, this material can be proposed as a soil improver into hydroponics systems, leading so an important alternative for food production in zones leaking of water. In the same way, it was found the possibility of use this material as a seal 3A in processes of asphalting of roads, highways and streets.

Jan 1, 2009

By Y. Wang, L. Liu, G. Xu, Y. Lv J. Sheng H. Zhang

In order to increase the service life of large scale coke dry quenching furnaces, the damage mechanism of lining was investigated, and the structure and properties of lining refractories used in cooling section were researched. The results showed that the abrasive wear volume of lining bricks at one fourth height section under skew tunnel was smaller than other sections. The wear loss of mullite brick and dense clay brick used in the lining of cooling section were respectively 8.02 cm3 and 11.65 cm3 in fifteen minutes. The mullite brick was laid with clay brick alternatively. By the different wear rate, the surface of lining was rough and uneven in the later service life, and short brick was easily dropped from lining. During the service, the basis wore off more easily than the aggregate. It is necessary to improve the wear resistance property, which will increase the service life of cooling section’s lining for coke dry quenching furnaces.

Jan 1, 2016

By P. C. Guillaume

Global plant modernizations or expansions cannot be considered in the same light as any other industrial investment project. Relationships between the partners, relationships and communications with the client, structure and organisation of the teamwork, schedule of the work, and a lot of other tasks and missions devoted to external contractors have to be defined considering one fundamental input: an operating plant. For an engineering company expert in processing, like UM Engineering, such a context requires a specific approach as well as specific procedures able to efficiently challenge the generated constraints. First of all, even if a detailed audit had been conducted at the beginning of the conceptual engineering phase, new elements will be discovered during the preparation and realization of the project, and must be continuously integrated. Consequently, a close proximity to the site is necessary. This is one reason why UM Engineering, most often, works in partnership with a local engineering company. The second important point for the client is that the operation must not be interrupted during the realization. In order to make that possible, UM Engineering has defined a specific project structure and organisation, integrating on a permanent basis the operators (the "users") in the project teams. This paper presents the way UM Engineering copes with this type of "multi-constraints" context with reference to the recent copper cellhouse modernization under realization for the CCR Refinery of Noranda Inc. in Canada.

Jan 1, 1999

By F. Kongoli

Nonferrous and ferrous smelting industries have recently faced the unavoidable necessity of changing and/or improving the smelting technologies as a result of the use of new raw materials which are becoming available from different geographical areas. These new feed materials usually contain different ore composition and higher level of minor components, which adversely affect the smelting process. Due to the problems encountered in several processes as a result of this feed diversification some work has been undertaken in order to make uniform the feed and avoid later surprises in the smelting process. However this has proven to be very difficult and sometimes almost impossible. In this work a more viable approach is undertaken to deal with this problem. It consists of controlling not the cause of the problem i.e. the feed composition but instead the results of this feed change, i.e. the end-point of smelting technologies. It is shown that this approach, when carried out through advances physicochemical modeling and simulation tools is not only easier and less costly but it also helps the control optimization and automation of the smelting processes. Several examples are given and future work is underlined.

Jan 1, 2003

By Zhihong Liu

In recent years, the removal of arsenic from different types of high arsenic containing materials produced in nonferrous metallurgical processes have been experimentally studied in the complex materials processing research group from Central South University. These materials include arsenic and antimony bearing flue dust, arsenic sulfide residue and arsenate bearing flue dust. The separation of arsenic from other valuable metals was carried out hydrometallurgically; for each type of arsenic bearing material, different processes have been employed individually to remove the arsenic effectively. In this paper, the flowsheets and typical experimental results have been summarized.

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In tungsten ion-exchange process, excessive sodium impurity enters into ammonium tungstate solution. However, the Na content of the final ammonium paratungstate (APT) product must be strictly controlled. Consequently, it is necessary to remove Na from the ammonium tungstate solution during processing in order to obtain the required purity of APT. In this study, porous Na specific absorbent, Na1+xAlxTi2−x(PO4)3, is used to remove Na from the ammonium tungstate solution. Through experiments, the effect of reagent concentration of Na1+xAlxTi2−x(PO4)3, reaction time, reaction temperature and Na concentration on the Na removal were investigated. The results showed that under optimal reaction conditions of reagent amount of NATP 1.0 times of theoretical amount, reaction temperature 25 °C and reaction time 15 min, the Na removal from commercial (NH4)2WO4 solution can reach 98%. Na1+xAlxTi2−x(PO4)3 has a good applicability to different Na+ concentrations. The obtained APT product reaches the national standard purity of zero level.

Jan 1, 2014