Search Documents

By X. J. Wu

Effects of various factors such as diaphragm materials, composition of electrolytes and current density on copper electrowinning from cupric chloride solutions was investigated. It is found that the crux of this process is to prevent the dissolution of copper by cupric ion and the formation of suspended CuCl precipitate. A process with high difference of copper concentrations between the feed solution and the spent electrolyte was selected. With this process, in which the feed solution contains 90 g/dm3 [Cu"], 3M NaC1, and 10mg/dm3 bone glue, and the spent electrolytes contains 10 g/dm3 [Cul, a very smooth and dense copper cathode can be produced with current efficiency above 93% and energy requirement less than 1.7 kwh/kg Cu at 25°C with N2 sparging. If a slightly higher energy requirement is permitted, smooth and dense copper cathodes can be produced at the current density up to 800 A/m2 with the identical solutions.

Jan 1, 1991

By Min Chen, Nan Wang, Zhen Tian, Yingying Shen

"The enrichment behavior of phosphorus in CaO-SiO2-FeOx-P2O5 slag was studied by making an investigation on the distribution of phosphorous content in slag and 2CaO·SiO2 phase. The research results showed that the existing 2CaO·SiO2 solid particles in slag were the sites for the phosphorous enrichment. The enrichment process of phosphorus in CaO-SiO2-FeOx-P2O5 slag can be recognized as: mass transfer of phosphorus from bulk slag toward the surface of 2CaO·SiO2 particle, superficial dissolution reaction of phosphorus to 2CaO·SiO2 and diffusion of phosphorus through the product layer of 2CaO·SiO2-3CaO·P2O5 solid solution to the inner of 2CaO·SiO2 particle. Compared to the 2CaO·SiO2 particles with larger size (500µm to 1000µm), the completion time of enrichment was shorter for the particles with smaller size (less than 50µm).IntroductionDuring ironmaking and steelmaking, significant amounts of slag are produced. Contrast to the high utilization of ironmaking slag, the treatment of steelmaking slag is more difficult and challengeable, and therefore, an alternative approach is to recycle the steelmaking slag inside the ironmaking and steelmaking process itself. The main limitation to the reuse of steelmaking slag inside the process is that the refining process may be aggravated caused by the phosphorous accumulation if it is used in the blast furnace burden [1]. At the same time, the phosphorous content of steelmaking slag (approximately 1%~5% P2O5) is too low for it to be used as raw material for fertilizer [2, 3]. Moreover, owing to the diminishing supply of global iron ores with low phosphorous content, the control of phosphorus in iron and steelmaking processes has become an increasing problem, and as a result, more amounts of high phosphorus containing steelmaking slag are produced. Therefore, a valuable approach is quite appreciated in which the steelmaking slag is recycled within the ironmaking and steelmaking process and at the same time, the high phosphorus-containing phases in the steelmaking slag, suitable for use as fertilizer can be separated and recycled effectively [4]."

Jan 1, 2011

By Teruo Bitoh, Shogo Izumi

"The effect of B203 flux melting on the structure and the soft magnetic properties of the (Feo.1sBo.20Sio.os)96Nb4 bulk metallic glasses prepared by casting has been investigated. The ringshaped bulk specimens were prepared by the B203 flux melting and copper mold casting. It was confirmed that the flux melting promotes the precipitation of the a-Fe(-Si) and Fe2B phases in the central region of the specimens. The ring-shaped bulk specimens show a flat hysteresis curve, indicating a good linear relationship between the magnetic induction and the applied magnetic field. These results show that it is possible to develop a new soft magnetic material that exhibits constant permeability, which is necessary for producing inductors and choke coils.IntroductionSince the success of forming Fe-based bulk metallic glasses (BMGs) with good soft magnetic properties, great attention has been developed to synthesis and properties of the BMGs [l, 2]. The BMGs have high glass-forming ability (GFA) and, therefore, they can be used to prepare bulk amorphous alloys with a thickness of the order of a few millimeters by casting. The soft magnetic properties of Fe-based BMGs are better than those of ordinary amorphous alloys; therefore, these BMGs have wider applications as soft magnetic materials [3-5]. It is often required for soft magnetic materials that the shape of the hysteresis curve is changed according to the demands of applications. For example, materials with ""flat hysteresis curves,"" which means the magnetic flux density (B) and the applied magnetic field (H) show a linear relationship up to rather high magnetic field, are necessary for producing inductors and choke coils. Flat hysteresis curves can be easily achieved by creating an air gap in the magnetic path. However, magnetic flux leakage generated in the air gap inhibits high-density packing of the electronic components. In order to achieve flat hysteresis curves without creating an air gap, Fe-based ordinary amorphous alloys are subjected to crystallization by annealing and transformed into thin surface layers of a-Fe; the crystallization results in the compression of the remained amorphous phase [6]. Another way to achieve flat hysteresis curves is the formation of secondary phase (such as Fe2B) that act as pinning site of magnetic domain wall displacements [7]."

Jan 1, 2013

By B. Willit, J. Martin

"Continued emphasis on water and energy conservation with less operator attention has created a need for more sophisticated cooling tower controls. A joint Betz/ASARCO project has produced a computerized water parameter controller and automated pumpless feed unit. Interfacing the unit via radio modem to the operator control room computer allows real time system status monitoring. Incorporating SPC principles to monitor and regulate all pertinent parameters yielded enhanced water control. This paper described the system design and present the results of a six month trial.BackgroundReducing operating costs and better manpower utilization are two of the largest concerns confronting maintenance managers today. At the ASARCO plant in Amarillo, a trial has been initiated to prove that it is possible to accomplish both of these objectives by using automated cooling tower control. The system is being adapted from a unit that was designed for continuously operating cooling towers in refineries and power plants by Betz Equipment Systems Division, a subsidiary of Betz Laboratories, Inc. The System l3000™ is designed to continually monitor conditions in the cooling system and to provide adjustments to the chemical balance for corrosion and deposition control. At Asarco, the unit was installed on the Rodline cooling system which operates on an intermittent basis.The primary justification for this project is to reduce costs of the five cooling systems in the plant. Current procedures require an operator to make visual checks every two hours on the five cooling towers as well as run lab tests on the water to insure proper treatment levels. This manpower can be better utilized by controlling the towers and collecting all the data available at one central location, in this case, the boiler house."

Jan 1, 1989

By David G. Dixon, Ahmad Ghahremaninezhad, Edouard Asselin

"In this study pertaining to the electrochemistry of chalcopyrite, the active/passive behavior of a chalcopyrite electrode in 0.5M sulfuric acid solution was investigated. Potentiostatic and potentiodynamic polarization and multi-cyclic voltanunetry were conducted to analyze the electrodissolution parameters of the electrode.The potentiodynamic and potentiostatic polarizations of chalcopyrite revealed the formation of a passive film on the surface of chalcopyrite. From the potentiostatic study in the passive potential region, a decrease in the dissolution current density by increasing the potential was observed. From this, it was concluded that the passive film is an n-type semiconductor and cation interstitial defects or anion vacancies are the charge carriers. From multi-cyclic voltammetry studies, four cathodic peaks at - 0.37, 0.30, -0.10 and-0.20 YsHE were detected on the surface of a passivated chalcopyrite electrode. The cathodic peaks at 0.37 and 0.30 V were connected to ferric to ferrous reduction and copper sulfide formation, respectively. The peaks at -0.10 and - 0.20 were related to chalcopyrite reduction. The products of the chalcopyrite reduction reactions were suggested to be Cu2S, Cu9fesS16 and Cu5feS4 and evolution of hydrogen sulfide gas (H2S).IntroductionChalcopyrite is the most abundant copper bearing mineral in the world and its dissolution behavior represents the most important technological consideration in the hydrometallurgical extraction of copper [I]. Since the current pyrometallurgical methods for copper extraction from chalcopyrite have environmental issues, many studies have considered the leaching and dissolution of CuFeS2 in different aqueous media [2-5]. The main problem associated with leaching processes is the slow dissolution rate of the mineral [6]. During the dissolution process, increasing the potential of the chalcopyrite in the anodic direction will cause the formation of surface layers which hinder the dissolution rate of the mineral [7]. The precise composition of the layers is in dispute. Previous studies have concluded that these layers could be sulfur [8-9], precipitated iron compounds [8], a solid electrolyte interphase (SEI) - which slows the rate of electron transfer- [10], a metal deficient sulfide [ll], or polysulfidic in nature [12-13]. In order to increase the leaching kinetics of chalcopyrite, the characterization of the layers formed during dissolution is essential and electrochemical methods are important to this end. Studies by Biegler [14] show nucleation and growth of a thin two-dimensional sulfide phase on the surface of chalcopyrite during the exposure of a polished sample in HzS04 solution or air. More studies by Biegler and Swift [15] have shown evidence for nucleation and growth of a 3-dimensional phase at low anodic potentials (around 200 mV vs. OCP). The current-time behavior of the dissolution process in this potential area has the characteristics of expansion and overlap of localized dissolution centers."

Jan 1, 2012

By Cameron Hams

Noranda's Process Reactor and Codelco's Teniente Converter are physically similar vessels, which leads to the commonly held misconception that the two processes are the .same. However, notable differences in chemistry, operating philosophy, and construction make them quite dissimilar. This paper compares and contrasts the Noranda Reactor and the Teniente Converter, and attempts to explain some of the apparent differences in behaviour and performance. The results of a worldwide survey of most operating Noranda Reactors and Teniente Converters, along with those processes that have ceased operation or are planning to be started-up in the future, are presented.

Jan 1, 1999

By E. A. Román

An ion exchange pilot plant, provided by Mesco Inc., was tested for antimony control in the electrolyte at three Chilean tankhouses for copper electrorefining: Chuquicamata, Potrerillos and Enami -Ventanas. The pilot plant, with a nominal extraction capacity of 1.2 kg Sb/day, worked connected to both experimental and commercial circuits, performing a total of 310 loading and elution cycles. An innovation in this process is the use of a chelating organic elution reagent, which presents some advantages over the traditional 6N HCI. This new eluent is amenable to continuous regeneration and recycling with high recovery efficiency. Antimony removal starting at initial, concentrations of 0.5 to 0.6 g/l of Sb down to steady concentrations of 0.1 to 0.0.6 g/l Sb, resulted in the production of High Grade copper cathodes with Sb contents below 0.1 ppm. Anodic slimes showed Sb contents below 1%.

Jan 1, 1999

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"The Center for Advanced Mineral and Metallurgical Processing is developing membrane production technology based on autocatalytic reduction of palladium from solution onto a unique, porous substrate. Surface membranes and catalytic structures are critically important to applications that range from hydrogen purification membranes to petroleum refining. Autocatalytic reduction processes represent a cost effective method of producing stable surface layered structures that have good working lives. These attributes are particularly important in the production of palladium alloy purification membranes used in hydrogen production. Although considerable research has investigated the interaction of hydrogen and palladium alloys, the mechanisms in play while the membranes form are not well understood. Preliminary research has identified three distinct deposition mechanisms and it appears that substantial control over the resulting membrane is possible.IntroductionPalladium-based membranes separate hydrogen from other gases because hydrogen is uniquely soluble in and readily passes through bulk palladium. As currently produced, palladium-based membranes are expensive and have short service lives. These circumstances are due in part to the lack of a complete understanding of palladium or palladium alloy deposition. The Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production.In membrane production, the palladium requirement depends on substrate surface properties such as surface chemistry, porosity, and roughness. Thin, defect-free membranes have been successfully produced on substrates of porous glass, alumina, and stainless steel. However, the differences in the thermal expansion coefficients of palladium membranes and porous glass or alumina substrates cause problems at operating temperatures. The use of stainless steel substrates is advantageous because stainless steels have thermal expansion coefficients similar to that of palladium and they are stable at the required operating temperatures (Wicke, E., Brodowsky, H. and Ziichner, H. ). Stainless steel is also readily available and relatively inexpensive."

Jan 1, 2012

By William C. Spindler

Five industrial installations of large lead-acid battery energy storage systems in operation in the United States, West Germany and the 'Republic of South Africa will be described. One example is for a deep mine shaft in which air ventilation and personnel evacuation require the highest reliability for emergency power. The battery system is designed for additional cost-effective benefits of peak load lopping and reactive power control. Commercially available lead-acid batteries of the following types are in use1 traction, truck, submarine, high power, and gel. Electrode grids of both the calcium and antimony alloy types are used. Applications include deep and shallow cycling as well as float and intermittent use. The advantages of sealed lead-acid batteries in UPS (uninterruptible power source) systems are well established throughout the world, and such system suppliers could readily develop markets for industrial emergency and peak power lead-acid storage battery installations.

Jan 1, 1990

By Zhi-gang Que, Sheng-li Wu, Guo-liang Zhang, Bo Su, Chao-gang Hou

NOx released during fuel combustion is one of the major air pollutants, such as acid rain and photochemical smog. At present, still not have an economical and effective method of inhibiting NOx emission for sintering flue gas. Therefore, controlling conditions of fuel combustions to enhance the reduction of NOx is important for decreased the emission. In this study, microsintering furnace has been performed to investigate the effects of NOx emission from char-N during coke breeze combustion. The results show that the emission concentration of NOx decreased with increasing temperature when it is sinter bed temperature higher than 1000℃. The lower emission concentration of NOx was obtained when the concentration of oxygen was decreased. And the maximum concentration of NOx will be reduced with the enhanced of heating rate. If heating preservation time was prolonged, it would promote to NOx reduction with reduction substances resulted in lower NOx emissions in the combustion of coke breezes.

Jan 1, 2015

By Pradip

The selective adsorption of chemisorbing fatty acids at high temperatures together with the addition of soda ash and lignin sulfonate as depressants is the key to the industrial processing of bastnaesite ores. This paper presents the results of a fundamental investigation that indicate that alkyl hydroxamates can be an alternative collector for the beneficiation of bastnaesite ores that contain barite and calcite as the principal gangue minerals. The primary mechanism for providing sites for the chemisorption of hydroxamate on bastnaesite appears to be through dissolution of cations, formation of the respective hydroxo complexes and readsorption at the interface.

Jan 1, 1989

By František Molnar, Zsolt Szentirmai, Juraj Schmiedl, Felix Sekula

"Hydrometallurgical nickel production in Sered Nickel Plant (Slovakia) that treated roasted Albanian ore left behind a considerable amount of the solid leaching residue. About 6 million tons of this fine-powder residue containing approximately 52 wt.% of iron in the form of oxides is to the present day stored in a stockpile. However, its iron content makes it a potentially interesting secondary raw material for iron production. This secondary raw material is not, unfortunately, suitable for direct treatment in iron and steelmaking processes.This paper presents results of the laboratory tests of pyrometallurgical method of processing of the leaching residue by its roasting and subsequent refining melting. The objective of the selective reducing agglomeration roasting was to reduce iron oxides and to simultaneously avoid reduction of chromium oxides and silica. Refining melting is carried out in an inert atmosphere. The products of melting are technically pure iron and slag.IntroductionThe leaching residue stockpiled on waste dump near already non-existing Nickel Plant Sered, Slovakia, is considered to be one of the most important environmental burdens in this country. The 40-years of an on-going effort focused on finding the methods for extracting metals and thus remove the waste dump have not been successful [1,4,5,6]. From the literature survey it is evident that past investigations have been following three main routes:1.Removal of chromium by mineral processing methods prior to its metallurgical treatment to achieve final chromium concentrations below 0.3 wt.%.2.Pelletization of solid leaching residue and its subsequent reduction in blast furnace and steelmaking plant and simultaneous removal of chromium.3.Pelletization of solid leaching residue followed by metallurgical processing of preliminary reduced semi-product in electric arc furnace (EAF) accompanied by partial reduction of chromium."

Jan 1, 2008

By K. Kashiwaya, N. Hiroyoshi, H. Furuya, N. Sumiya, M. Tsunekawa, M. Ito

"The number of hybrid vehicles is increasing and this is causeing an increase in waste nickelmetal hydride batteries. The cathode activating agent of batteries is made of nickel hydroxide and the anode activating agent is an alloy of nickel and rare earth elements. Conventional rotary kiln methods cannot recover the rare earth elements, and hydrometallurgical treatment of crushed product consumes large volumes of agent. The physical separation of the anode alloy from the cathode hydroxide would make it possible to reuse the alloy. The authors have reported separation of anode and cathode components in the large size fractions using a newly developed dry magnetic separation method. Wet magnetic separation has been applied to the powder fraction and about 90% anode purity was achieved. This paper reviews experimental results from previous publications and proposes an integrated treatment process for crushed nickel-metal hydride batteries.IntroductionEnvironmentally-conscious clean energy vehicles have attracted much attention in developed countries and particularly hybrid vehicles are increasingly mass-produced as low emission vehicles. Hybrid vehicles have both a gasoline engine and an electric motor to save on gasoline usage and a nickel-metal hydride battery is used to store electric energy. The battery contains Nihydroxide and Co as the cathode activating agent and an alloy of Ni and mischmetal (mM), a rare-earth element mixture consisting of La, Ce, and Nd, as the anode hydrogen adsorption component. In conventional recycling, the Ni and Fe are recovered with a rotary kiln-electric melting process and the Co and mM go to the slag component [1] and hydrometallurgical treatment of crushed product consumes large volumes of agent. Japan Oil, Gas and Metals National Corporation have proposed a low energy and low cost recycling treatment process combining the physical and chemical treatments and the authors are investigating the physical treatment process."

Jan 1, 2008

By R. G. Haire

Studies of the f-elements under pressure provide important insights into their solid state chemistry and physics. From such studies, of the elements and their alloys, it has been established that the normally localized f- electrons of several of these elements can become, involved in bonding under pressure. The electronic behavior of f-element compounds under pressure tend to be more difficult to interpret, due to the variety and the nature of electronic orbitals that are present. The 4f-elements and some 60% of the 5f-elements have been studied under The systematic comparisons that have been established for these materials are discussed.

Jan 1, 1992

By B. R. Adams

This paper discusses the use of a reacting CFD model to determine chalcopyrite kinetics in a drop tube furnace and to predict the reaction of a chalcopyrite concentrate in the reaction shaft of an industrial smelter. Reacting CFD codes can be applied to determine the consequences of the interaction of gas with particles and therefore improve the ability to derive kinetic parameters that take into account the temperature and oxidation histories that different particles will see. This paper describes the application of such a model to derive improved kinetic parameters for the pyrolysis and oxidation of chalcopyrite. The reaction shaft model includes the effects of turbulent fluid mechanics, entrained flow mixing, turbulent particle dispersion, heterogeneous particle reactions, radiative and convective heat transfer, and' surface and bath deposition rates. Particle reaction and composition characteristics are predicted as a function of particle trajectory and deposition and are used to aid in evaluating shaft performance.

Jan 1, 1999

By David Tisdale, Phillip Mackey, Nagendra Tripathi, Matthew Kreuh, Pascal Coursol

Xstrata Nickel’s Sudbury smelter operation is based on fluid bed roasting of Ni-Cu sulphide concentrate, followed by electric furnace reductive smelting and Peirce-Smith converting to produce a Bessemer matte for electro refining, along with sulphuric acid produced from smelter gas. While the site dates back to the 1930s, the present smelter configuration has been operational since 1978, and currently has a nominal capacity of about 67,000 tpy of contained nickel and is investigating options to expand in future up to 85,000 tpy. As part of a review of plant capacity options, a new metallurgical model of the plant was developed in order to examine a number of processing alternatives. Based on the METSIM™ platform, the present model includes the ability to examine the impact of a number of plant parameters on potential plant performance including; for example, the following: percent of sulphur elimination in roasting, matte grade, degree of matte metallization, temperature, coke requirements, sulphuric acid production, CO2 emissions and overall energy requirements. The process model also includes a number of special features adopted; for example, approaches to effectively model the complex Ni-Cu-Co-Fe-S-O matte system. This paper provides a description of the model and gives an overview of the results. As well as presenting the results of the present study, the applicability of this modeling approach to pyrometallurgical systems in general is also briefly discussed in the paper.

Jan 1, 2009

By Magdelinka Padenkova-Yaneva, Emilia Christova Kostakeva

"Environmental protection is becoming over the years an increasingly significant problem of mankind. Up to the last decade the only way to make the domestic waste harmless in Bulgaria was deposition on uncontrolled landfills without undertaking actions for protection of the soils. This also caused pollution to spread into the surface and underground waters and that is why actions are now undertaken for remediation of contaminated soils. This is achieved by developing projects for the closing down of polluted sites. In the present paper some projects for closing down of polluted areas are discussed. The actual conditions are examined and project decisions for preventing the surface waters from penetrating into the waste are presented. In this way the pollution of the soil is stopped and the soils are gradually remediate.IntroductionSoil is the topmost layer of the earth crust. It consists of mineral particles, organic substances, water, air and living organisms and is an extremely complex and changing living environment. Soil is a non-renewable natural resource which is of considerable importance in a number of crucial processes (production of foods, storing, filtrating and turnover of many substances, including water, carbon and nitrogen). It also serves as a basis for human activities, shaping the landscape, ground on which cultural heritage is built, and source of raw materials. These functions of soil must be protected both because of their social and economic significance and from the point of view of environmental protection.The processes of erosion, loss of organic substances, compaction, salination and contamination contribute to the degrading of soils accompanied by a negative impact on human health, natural ecosystems and changes in climate, as well as on the economy. All these make it necessary to protect soils from contamination. Over the last years intensive work started in Bulgaria for the construction of controlled sanitary landfills for rendering municipal solid waste harmless. Pursuant to Bulgarian legislation, in these controlled sanitary landfills measures are undertaken for protecting the soils from contamination through appropriate project decisions – the filtration of the products from the biological decomposition of waste into the adjacent sites (soils) and, therefore, the contamination of the surface and underground waters is prevented. At the same time the purity of air is maintained, human health is protected and conditions are created for including the controlled sanitary landfills into the surrounding landscape."

Jan 1, 2008

By James L. Whitlock

Biological treatment of mining and industrial effluents reached full scale commercialization around 1980. These proven, low cost, technologies have been limited in application due to a number of factors, including extended periods of time and cost required for pilot testing as compared to chemical treatment technologies, lack of biological expertise in metallurgical personnel, longer treatment periods in some cases, and performance failures based on improper application. Renewed interest in biological treatment technologies is being driven by permits with lower effluent concentration criteria, permits with bioassay evaluation, the need to remove thiocyanate, nitrates, sulfates and? other parameters. Chemical treatment processes, in general, have not been able to meet these present requirements, or require elaborate? combinations of processes, in terms of effluent quality and treatment economics. This paper addresses biologieal treatment of mining and industrial waste waters and selected recent advances in these technologies. The future looks very bright for application of these low capital and operating cost technologies,

Jan 1, 1998

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

Dust, or airborne particulate matter, from metal smelting can be either mechanically or thermally generated and it negatively affects the indoor air quality as well as the fugitive emissions from the plant. The thermally generated dust is often referred to as fume and it is typically generated whenever liquid metal comes into contact with air. For practical reasons, such as vehicle access, etc. it is often difficult to collect 100% of the fume. It is therefore highly desirable to develop processes and optimize operational procedures so that fuming can be kept to a minimum. In this series of experiments, the mechanism of active oxidation and fume formation from liquid silicomanganese under an impinging air jet in the temperature range 1400-1600°C has been explored. Characteristic properties of the fume have been established; particle diameter, shape, size distribution, and elemental composition are reported. The oxidation process is described in terms of vaporization, oxidation and agglomeration. In the boundary layer, two competing mechanisms seem to be operative in parallel: a direct oxidation of Mn vapor, and a two-step oxidation of silicon. The thermodynamic and kinetic conditions governing the two mechanisms are discussed.

Jan 1, 2016

By C. H. Tsau

The intermetallic compounds of Ni-25Al-xFe, x is 20-40 at.%, were prepared by arc melting and drop casting into ingots, and were rapidly solidified into ribbons by melt spinning. The microstructure evolution of these alloys with varied Fe content were examined by the x-ray diffraction, optical microscope, scanning electron microscopy and transmission electron microscopy. The results reveal that two phases, {y'} and {B} phases, are existing in the alloys with low Fe content, and the microstructure changes from the mixture of y' and {B} phases to a single 0' phase when the Fe-content reaches to 40 at.%. Also, the formation of y' phase will be suppressed by rapidly solidified process. For annealing both of the melt-spun and the cast specimens, a disorder 0 phase was revealed in both of the ribbon and the cast ingot of Ni-Al-Fe alloys with higher Fe content. In addition, increasing the increment of iron which substituting nickel in this alloys results in increasing the lattice parameter of both {y'} and{B} phases.

Jan 1, 1992