Search Documents

By A. D. Zunkel

The zinc in electric arc furnace dust (EAFD) arises from the fuming and oxidation of the zinc present, mainly as galvanizing, in automotive scrap. The dust is collected from the electric furnace offgases in bag filters and is classified by the EPA as a hazardous waste (K061). As more zinc is used in galvanized sheet on automobiles and more automobile scrap is recycled via the EAF, the more zinc will be available for recovery and recycling. EAFD will become a more prevalent and important source of zinc compared to the traditional zinc sulfide concentrates ifit can be cost effectively processed.

Jan 1, 1995

By Geoffrey A. Brooks, M Akbar Rhamdhani, Md Saiful Islam

A novel electrically-enhanced metal purification using slag has been developed. This was achieved by applying DC potential between liquid metal and slag phases. The concept was demonstrated through small-scale experiments at temperatures of 1500-1600oC for the removal of boron from Si-B melt using CaO-SiO2-16wt%Al2O3. Silicon (containing B) and slag were reacted in an alumina crucible in a resistance tube furnace. A circuit was produced by immersing graphite rods into the silicon bath and the slag layer. Electrical potential differences of up to 3.5 V were applied during the reactions. The reaction rates, the opencircuit voltages and short-circuit currents (in the case when the potential was applied) were then measured and determined for various slag to silicon ratio. It has been shown from this study that both the apparent rate and the boron partition ratio were increased by a factor of approximately 1.6.

Jan 1, 2014

By Marco Pasetto

The possibility to re-use marginal materials (by-products) deriving from industrial activities in the construction of road infrastructures, as total or partial substitution of natural aggregates, successfully combines demands for economy and environmental sustainability. The paper presents the results of a laboratory study, conducted at the Experimental Road Laboratory of the University of Padova, to verify the suitability of a particular type of electric arc furnace slag to be recycled in the lithic skeleton of high-performance asphalt mixes (porous asphalt, high modulus mixes, stone mastic asphalt, nonskid surfacings) for road and airport flexible pavements. the process of transformation of iron and steel slag into a product that can be used in road building is described, along with the characterisation of the mixtures, plus an analysis of the results of a wide battery of mechanical-performance tests. This study forms part of wider theoretical ? experimental research being done at the University of Padova in order to improve knowledge of the characteristics of succedaneum materials and check their possible applications in road and airport construction.

Jan 1, 2006

By S. Rick Gilbert

In the course of producing a final metal product, smelters, refineries, and other metallurgical facilities produce wastes which often come under the ?scrutiny of Federal and state regulatory agencies. Many of these wastes contain combinations on zinc, copper, lead, cadmium, nickel or other metals. Frequently in the form of reverts, dusts, or sludges, these metal-containing wastes are often buried in a landfill or speculatively accumulated for future action. Environmental liability can be reduced in many cases by selecting,-a recycling facility which can re-process the waste for.' metal recovery. Encycle, at its hydrometallurgical facility Corpus Christi, has Successfully processed a variety of metallurgical by-products and wastes and returned those contained metals to commerce.

Jan 1, 1995

By A. V. Tarasov

Investigations of thermodynamic properties of Cu-Ni and Cu-Ni-S systems and mattes have been conducted with the aid of a MC-1301 mass-spectrometer designed for studies-of processes of vapor formation of hardly volatile substances. The instrument comprised a combination of an evaporator of Knudsen chamber type with a mass-spectrometer for analysis of the vapor phase, In the process of studies of molten Cu-Ni-S systems and commercial-grade mattes within a temperature interval of 1400-1800 K the partial pressure of sulfur was measured by means of complete isothermal evaporation and the partial pressure of copper and nickel by comparison of ionic currents. The partial pressure values of the components above the molten Cu-Ni-S were used for calculation of activities of the respective components in the melt. The copper and nickel activity data obtained was used for assessing the amount of dissolved losses of these metals in autogenous smelting slags.

Jan 1, 2003

By Eugene Jak

Copper sulphide processing technologies face increasing pressures associated with decreasing concentrate grade leading to increasing thermal inefficiency and lower productivity. Impurity concentrations are on average increasing, creating potential environmental risk and additional treatment costs. In copper flash smelters dust, partially oxidised materials and fume formed from the condensation of volatile impurities, are routinely recycled to the feed. In the converting stage the heat balance is maintained by charging anode reverts and other inert materials. In both cases, the thermal energy available from sulphide oxidation is not fully utilised or optimised. The productivities of both smelter and converter stages can be potentially increased through the addition of a high copper, low iron, low impurity precipitated copper product. Calculations are carried out for fayalite smelter and calcium ferrite converter slags using an optimised FactSage thermodynamic database. The potential for significant increases in smelter and converter productivities using existing technologies are predicted.

By Shengli Wu, Wei Huang, Xinliang Liu, Kaifa Zhang

The slagging behavior, the phase of primary blast furnace slag and its transformation law of structure for the single furnace burden were studied in this paper. The results showed that the formation of primary slag was controlled by CaO/SiO2, Al2O3 content, MgO content, reducibility, iron content and porosity of the furnace burden. Fayalite (2FeO•SiO2) was easily formed from acid ferrous furnace burden while kirschsteinite (2(Fe,Ca)O•SiO2) was produced from alkaline ferrous furnace burden

Jan 1, 2015

By K. Adham

"Fluidized beds are utilized in a wide range of high-temperature applications throughout the metals and materials industry. Their main advantage is the fast and uniform heat and mass transfer between the hot combustion gases and the particulate solid feed. A further benefit can be the lowering of the processing plant's energy consumption, through heat recovery from the fluid bed processes used for solids heating. Here, the enhanced energy efficiency of fluidized systems is investigated and the modeling results are discussed for three configurations: the flash tube, the single bubbling bed and the multi-stage fluid bed. Key thermal design aspects of each system are identified based on results from process simulations, in order to benchmark their main operating features and overall energy efficiency. Suitability and applicability of each configuration is also discussed based on a number of process and material property considerations.IntroductionCombustion based heating of particulate solids is commonly done using three different types of fluidized beds. The flash tube (FT) is similar to a hot pneumatic transport system. The single-stage fluidized bed (FB) typically uses in-bed combustion. The multi-stage fluidized bed (MSFB) can have two or more stages stacked into a tower.Flash tube (FT) suspends the incoming solid charge in a high-velocity stream of hot combustion gases. To maintain the solids suspension in the FT, two parameters are required: high velocity for elutriation of the particles and adequate solid-to-gas ratio for avoiding high pressure drops and solids drop-out [l].The fluid bed (FB) works at much lower velocities than the flash tube. Therefore, most of the solids are not conveyed in the gas stream, but are only suspended in a liquid-like manner. At minimum fluidization velocity (Umr), the gas flow exerts just enough force on the solids to keep them suspended in place [2].Multi-stage fluid bed (MSFB) heats up the solids as they are transferred from an upper bed level to a lower one, counter-current to the rising flow of hot gases generated at the lowest stage. As the temperature and volumetric flow of the gases decrease from bottom to the top stage, smaller bed diameters can be used in the energy recovery stages [3]."

Jan 1, 2014

By Tsembel Darjaa, Toru H. Okabe, Yoshiaki Umetsu

"With the purpose of extracting molybdenum and rhenium from molybdenum sulfide concentrate; .electrolysis of slurry, solvent extraction and ·precipitation operations were carried out. The slurry of the concentrate in 10 mass% NaCl aqueous solution was continuously circulated into a vertical type 10 stack bipolar electrolytic cell consisted of carbon electrode disks, and, the concentrate was dissolved by electrochemically generated oxidizers at 313 K. The current efficiency for molybdenum dissolution was 73 % after 10 hours electrolysis, and the leach solution was found to contain 0.2 mol/l of molybdenum and 4x10-5 mol/l rhenium. This result shows the dissolution is more than 8 times faster than that obtained using a single cell. The leach solution from electro-oxidation was then subjected to a solvent extraction for rhenium which is then recovered as sulfides. After rhenium separation, molybdenum was precipitated by pH adjustment, and solid MoO3 (H2O)x crystals, free of sulfate, were obtained from the leach solution containing large amount of so42-.IntroductionIn the past, electro-oxidation using a bipolar cell was applied for leaching molybdenite concentrate and ores at U. S. Bureau of Mines [1-3] and also at Bhabha Atomic Research Center [4]. In· these previous studies, Moebious type bipolar cells, in which electrode plates were vertically inserted into the free surface of the electrolyte, were employed and its effectiveness was demonstrated.Recently, the present authors studied on leaching of Mongolian molybdenite concentrate, and the effectiveness of leaching of the concentrate by electro-oxidation in alkaline and acidic NaCl solutions was demonstrated [5]. The leaching reaction during the process can be explained by the 18 electron transfer reaction of molybdenite (MoS2) with the oxidizers produced in-situ by electrolysis of NaCl aqueous solution. Further investigation was made with respect to various process parameters for electrooxidation such as pH, pulp density and temperature of the slurry, and the dissolution behavior of minor elements such as iron, copper, and rhenium [6]. Solubilities of molybdenum in the leach solution at, various temperatures and pH .was · studied, and feasibility of molybdenum recovery by hydrolysis of molybdenum species was demonstrated. By adjusting the pH of the leach solution, molybdenum oxides or hydroxides free from sulfate were successfully obtained from the solution containing large amount of sulfate ion. Rhenium present in the concentrate at a level of several tens of mass ppm was found to dissolve into the leach solution, and co-precipitate with the molybdenum compounds. Rhenium in the leach solutions, therefore, has to be recovered before precipitation of molybdenum, otherwise it is lost in the precipitate."

Jan 1, 2000

By Dajian Wang

To obtain the thermodynamic properties of a multicomponent liquid alloy system over the whole range of concentration at an arbitrary temperature, the free volume cell theory has been applied to derive the formula of activity coefficients of liquid solutions based on the infinitely dilute solutions at some temperature. The linear logarithmic relationship between activity coefficients of binary dilute solutions and reciprocal of absolute temperature have been verified, and are in good agreement with the experimental values from the literature. The Monte-Carlo algorithm was used to calculate the nonlinear end value equations of binary systems, then the free volume parameters obtained were correlated with the activity coefficients of liquid binary, ternary, and quaternary systems at an arbitrary temperature. Three dimensional a-X-T diagrams of some binary systems representing the temperature and concentration dependence of activities were plotted. The calculated results regarding non-ferrous alloy systems have been statistically examined with the experimental values from the literature. Hence, this simple approach could be useful for analyzing thermodynamic properties of liquid alloy systems.

Jan 1, 2000

By Jin-tao Gao

In order to recover Ti resource from titanium bearing blast furnace slag, a new technology to separate perovskite phase from CaO-TiO2-SiO2-Al2O3-MgO system by supergravity is researched. In the condition of gravity coefficient of 750g, treatment temperature of 1305°C and time of 20min, the significant layers appear in samples which are obtained by means of centrifugal treatment. Along the direction of the supergravity, the volume fraction of perovskite phase increases gradually, and the equivalent diameters of perovskite phase crystals increases with the area approaching to the bottom of the sample. It is indicated that TiO2 is enriched in the bottom of sample as concentrate with a recovery ratio of 74.05% by supergravity treatment.

Jan 1, 2014

By W. Dresler

Design details of a 100 kVA DC electric-arc reduction furnace are described. The furnace is equipped with a 610 mm (24 inch) diameter graphite crucible hearth. A 76 mm (3 inch) diameter top graphite electrode is used as a cathode. The current passes through the bottom of the crucible and is carried to a bottom plate (the anode) by conductive magnesia carbon bricks. The furnace can be operated up to a maximum of 120 V, 1800 A, and presently 100 kW. The start-up operating experiences and metallurgical results of one reduction test with a Montana chromite containing 38% Cr2O3 are discussed.

Jan 1, 1994

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the fum ace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By B. Garcia-Egocheaga, J. Rutten, N. Goicoechea, U. Meurer, Mager K., W. Saage, Simonettim F.

Because of the increasing use of zinc as an active and passive anticorrosion agent for steel, leading to constantly growing return rates of galvanized steel components, especially through the automotive industry, major Electric Arc Furnace (EAF) flue dust amounts with higher zinc contents will accumulate in future. Landfilling of steel plant flue dusts is no longer allowable for ecological reasons. These dusts are classified as hazardous by law. Waelz technology is safe and reliable. The range .of treatable feed materials has been extended by process modifications and state-of-the-art offgas technology. Waelz oxide, the product, is delivered to metal smelters for zinc production and the byproduct, Waelz slag, can be used in road construction. Despite the fact that Waelz technology is among the best available techniques (BAT), it is continuously being optimized further with respect to energy input, product and offgas quality in order to comply with the ever more stringent environmental regulations. However, if these flue-dusts are treated, the loops between the steel and the zinc industry can be closed by reusing recovered zinc which in tum leads to savings in natural resources and a more reasonable use of landfills.

Jan 1, 2000

By Yongqi Sun, Zuotai Zhang

Hot slags, at the temperatures of 1450-1650 oC, carry a substantial amount of high quality thermal energy, which represents the largest undeveloped energy source in the steel industry. However, the waste heat recovery rate in China is less than 2%; thus there is a great potential of waste heat recovery. In this study, we investigated a chemical method to extract the waste heat from high temperature blast furnace slags, i.e., sludge gasification. Sewage sludge, another substantial waste produced in the municipal system, need to be timely disposed, the organics of which could be gasified using the waste heat in the slags for the purpose of syngas production. Both the kinetics and thermodynamics of the sludge gasification process were clarified here. Most importantly, an integrated system composed of multiple systems such as the steel industry, the cement industry, the municipal system and the chemical engineering industry, was analyzed in this study.

Jan 1, 2016

By Shizhe Liu, Bing Li, Heng Wang, Zuxin Zhao

In this paper, cyclic voltammetry and chronoamperometry have been applied to investigate the effects of Nd2O3 concentration on the anode effects, critical potential for the anode effects and Nd2O3 reduction in LiF-NdF3-Nd2O3 melts at 950℃. The results show that the oxidation peaks in the potential of about 2.7V are attributed to the oxygen ions oxidation and the peak current density increases with Nd2O3 concentration increase from 0 to 0.5wt%. The critical potential caused the anode effects shifts to 0.3V more positive value as Nd2O3 content in the melts decreases from 0.01wt% to 0.5wt%. The cyclic votammograms on W electrodes in the LiF-NdF3-Nd2O3 melts present two pairs of reduction and oxidation peaks, indicating that the reduction of Nd ions in the LiF-NdF3-Nd2O3 melts in two steps rather than one step.

Jan 1, 2014

By R. E. Brewer

Pilot scale flotation tests were conducted with a l?ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pet of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated. The tailings were first water leached at approximately 60? C, and the water-leached tailings, containing approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH' and sodium sulfide addition on gold flotation recovery and redox potentials were examined. Maximum gold flotation recovery, 36 pct, was achieved at pH 8,5 with a sodium sulfide addition of 0.18 Ib/st. Overall gold recovery by leaching and flotation was in the range of 70 to 80 pet.

Jan 1, 1989

By R. Padilla

A thermogravimetric study has been conducted to follow the decomposition and volatilization of arsenic from enargite concentrate in nitrogen and slightly oxidizing atmospheres. Temperature has a large effect on the rate of volatilization of arsenic. Fractional volatilization of arsenic as high as 98% were obtained in less than 60 min at 650°C in nitrogen atmosphere, while in slightly oxidizing atmosphere the same volatilization could be achieved in 30 min. It was found that arsenic volatilizes as sulfide in nitrogen atmosphere and as 4xture of sulfide and oxide in atmospheres containing 1% oxygen. By using the pore blocking and the first order kinetic models, apparent activation energies of 213 and 200 kJ/mol for the temperature range of 780 - 900 K and 205 and 184 kJ/mol for the temperature range of 900 - 985 K were determined for enargite and copper concentrate, respectively.

Jan 1, 1997

By James E. Simpson, Suresh V. Garimella, III de Groh

"An experimental and numerical study of the horizontal Bridgman growth of pure succinonitrile (SCN) and of a succinonitrile-1.0 mol. % acetone alloy (SCN-1.0 mol. % ACE) has been performed. Experiments at growth rates of 0, 2 and 40 µmis were investigated. The solid/liquid interface was stable (non-dendritic and non-cellular); however, it was not flat. Rather, it was significantly distorted by the influence of convection in the melt and, for the growth cases, by the moving temperature boundary conditions along the ampoule. For the alloy, the interface was determined to be unstable at growth rates greater than 2.8 µmis, but stable for the no-growth and 2 µmis growth cases. When compared to the pure SCN interface, the alloy interface forms closer to the cold zone,· indicating that the melting temperature has been suppressed by the addition of the alloying element. Two-dimensional computer simulations were performed for the no-growth case for both the pure and alloy materials. These simulations indicate that a primary longitudinal convective cell is formed in the melt. The maximum magnitude of velocity was calculated to be 1.515 mmls for pure SCN and 1. 724 mm/s for the alloy. The interface shape predicted by the computer simulation agrees well with the experimentally determined shape for the pure SCN case. In ongoing work, numerical simulations of the process during growth conditions are being performed.IntroductionIncreasingly, advanced materials used in the aerospace, automotive, optics and electronics fields require low levels of defects and high levels of solute uniformity. Directional solidification by the Bridgman process is widely used for synthesis of these high-quality materials. During Bridgman crystal growth, heat and mass transfer by both thermal and solutal gradient-driven convection and diffusion influence the shape of the solid/liquid interface and dopant segregation levels, and hence, directly determine the final crystal quality. Key process parameters include the applied furnace temperature distribution and rate of translation, ampoule properties and furnace orientation."

Jan 1, 1999

By Jiao Li, WenhuiMa, KuixianWei, YongnianDai, Cong Zhang

The paper studied the diffusion process of nitrogen and characteristic distribution of iron impurities in the bottom of cast crystalline silicon ingot along the direction of crystal growth. According to the dynamics analysis of the decomposition of Si3N4 coating, the diffusion process of nitrogen into multicrystalline silicon ingot during casting process should be divided into three steps. The diffusion length of nitrogen in multicrystalline silicon ingot is 700 μm. The results of EDS analysis indicate that the distribution characteristic of iron in multicrystalline silicon ingot is concerned with the diffusion process of nitrogen in this length. Based on the above research results, the distribution model of iron in casting multicrystalline silicon ingot was established and verified by the experimental results.

Jan 1, 2015