Search Documents

By Xianming Zhou

Mining economics is such that too conservative in safety will result in a considerable penalty in mining cost. However, initial planning and design of a mining project often must be done without complete information. The assurance of economical and safe mining is thus difficult. This study is focused on the improvement of the mine design associated with Zhaoyuan Gold Mine in P.R. China as more information becomes available. Attention is given to the selection of backfill structures. Based on a proposed practical finite element model, a design, which is believed to be not only reliable but also cost-effective, is recommended for further mining operations in this mine.

Jan 1, 1989

By Jinsheng Chen

To maintain the stability of longwall tailgate entries, they have to be supported by not only the primary roof support but also the secondary roof support due to the impact of the longwall mining¬induced abutment loads. Depending on the mining condition of a typical coal seam and its distance from the previous panel's gob, the longwall tailgate entry is often reinforced by the secondary roof support in the form of standing supports and/or cable bolts or trusses during longwall retreat, Even though lots of research work has been done to study the behavior of different standing supports in the laboratory. their function and requirements for a typical mining condition are still not fully understood due to lack of field data and correct assumptions about the behavior of the already-bolted entry roof under mining-induced abutment loads. Therefore, the application of the secondary roof support for tailgate entry roof control is still limited to trial and error, which often results in either higher cost for tailgate roof control if the design is too conservative or more production delays due to roof falls in the outby tailgate entry if the design is inadequate. To have a better tailgate roof control with reasonable roof control cost, RAG American Coal, NIOSH, and HeiTech have been conducting a joint research project to monitor actual roof loading, roof deformation, and entry convergence in the tailgate entry of 10 North panel at RAG Emerald mine. The actual roof loading data are used to calibrate and improve the roof control model for longwall tailgate entries, which has been developed by RAG American Coal, and to further reduce the roof control cost for longwall tailgate entries. The authors in this study attempt to discuss the Roof Control Model developed by RAG American Coal. in which some guidelines or important parameters for designing the secondary roof support for longwall tailgate entries are proposed.

Jan 1, 2003

By André Zingano

This paper analyses possible causes for floor heaving in room-and-pillar coal mining. The coal mines are in the southern part of Brazil, where the Barro Branco Coal Seam varies in depth from 20m to 400m, and a very thick volcanic formation overlies part of the sedimentary basin. The erosion of part of the volcanic formation causes this large range of overburden thickness, which formed large V-type valleys. The mine in study is located near the slope of one of these valleys. The mine inclined shaft is at the lower overburden thickness area of the valley and the mining is developing toward the thicker overburden area. The floor heave occurred in the crosscuts, which are parallel to the slope valley direction. Numerical modeling was applied to study the stress distribution around the openings; and fieldwork on the floor heaved entries was carried out. The geometry of mining (pillar and openings width) also was analyzed. The results showed that the very weak rock and the high horizontal stress were the causes of floor heave. As the mining gets near the valley slope, the stress distribution around the crosscuts changes considerably. In addition, the stress distribution changes as the mining goes far from the crosscut. Keywords: floor failure, room and pillar, finite element model

Jan 1, 2002

By D. M. Shu

A two-dimensional finite element modelling technique is applied to predict the subsidence movements on a sloping ground surface above a completely mined panel. The modelling is carried out for the surface both directly and using a combination of an equivalent horizontal surface and a rays projection method and the result compared. The rays projection method provides the subsidence components on a sloping surface from the corresponding ones on an assumed equivalent horizontal surface through the point of mean elevation of the relevant part of the sloping surface. This method is used next to compare the subsidences, horizontal displacements and horizontal strains from the mining of a given panel at the surface for different inclinations. The results show that the magnitudes of the subsidence components are greater on the dip side of the slope from the point of the mean elevation, than the corresponding ones on the rise side and the asymmetry increases with the inclination of the surface. The findings are also compared with those of other research workers.

Jan 1, 1992

By B. N. Whittaker

The paper briefly reviews the type of support and stability problems encountered in mining tunnels in U.K. Carboniferous rock conditions, particularly the Coal Measures where almost all such tunnels are located. Stability prediction of mining tunnels is discussed and a computer-based model which deals with stratified rock conditions is described. Various schemes for monitoring the stability of mining tunnels are examined and the application of the results discussed. Comparisons between predicted and measured Closure values are presented for a major Coal mining tunnelling project at Selby in the North Yorkshire Coalfield. Conclusions are drawn concerning the application of the present prediction technique together with the importance of underground monitoring. Examples of different types of mine tunnel stability problems encountered in the U.K. Coal Measures are discussed and comments made on the secondary effects of tunnel peripheral rock weathering and corrosion of the associated support systems.

Jan 1, 1987

Effective strata control, utilising fully encapsulated roof bolts, is dependent on the installed quality of the reinforcement elements. One mechanism by which fully encapsulated roof bolts may become less than fully effective is by gloving (glove fingering) and un-mixing of the resin. Following some small roof failures containing gloved bolts, investigations have been undertaken in some New Zealand coal mines to determine the extent of, and mechanisms involved in, the gloving of fully encapsulated roof bolts for a range of roof types and installation methods. Gloving, in this context, refers to the resin cartridge partially or completely enveloping a length of the bolt, typically with unmixed resin filler and catalyst/hardener remaining within the cartridge. Results have shown that gloving and un-mixing is a systematic and widespread phenomena, occurring across a range of resin and/or bolt manufacturers, and across a variety of roof types. Gloving was found in bolts installed using: hand held pneumatic and continuous miner mounted hydraulic methods, under run of mine (ROM) conditions by mine workers, and under controlled "best practice" conditions. The roofs bolts investigated are all 1800mm (6ft) long, and have shown that, on average, 485mm (-19") of the bolt length is gloved and/or unmixed. This equates to a 27 percent reduction in effective bolt length. The effected length of bolt is sufficient to impact on the load transfer/reinforcement capabilities of the bolt system, and hence impacts on the design assumptions and subsequent stability assessments. Furthermore, there is a direct relationship between the mechanism for the gloving of bolts and an increased occurrence of resin loss and reduction in encapsulations length in soft (less than 10 MPa) and/or highly fractured rock. Investigations have concentrated on developing an understanding of the mechanisms involved. This has been undertaken using both field installations and recovered bolts, as well as test bench trials. The mechanisms involved have been confirmed as being: the development of a pressure front as the bolt encounters the resin and is spun up the hole, which, in turn, leads to over-pressurisation and radial expansion of the resin cartridge, resulting in an increase in diameter of the plastic resin cartridge, which allows the bolt to be spun up into the cartridge without making sufficient contact to shred the cartridge or the hardener tube, resulting in an unmixed portion of resin.

Jan 1, 2003

By Eric R. Bauer

Skin failures of roof and rib in underground coal mines continue to be a significant safety hazard for mine workers. Skin failures do not usually involve failure of the support systems but result from rock or coal spalling from between the support elements. For instance in 1997, over 800 miners were injured by roof and rib falls, of which 98 pet were the result of skin failures. Also, nearly 80 pct of the roof and rib failure injuries occurred at or near the working faces in development sections. The face area is a zone where the potential for skin failure accidents and injuries and roof and rib failures, in general, is high because of mining activity, ground readjustment due to changing stress conditions, and the higher exposure of mine workers. In addition, failures occur where the roof and rib are unsupported. This paper features a review of the roof and rib accident statistics resulting from skin failure, highlighting the incidences by average days lost, in-mine location, state, MSHA District, and worker activity at the time of injury. A detailed analysis of recent fatalities caused by skin failure is included. Also discussed are the causes of roof and rib skin failures, current methods and support materials for skin surface control, as well as a historical literature review of skin failures and control methods.

Jan 1, 1999

By Gexin Sun

This paper overviews the recent research progress in predicting cutting performance using fracture mechanics principles. It is emphasised that rock fragmentation due to cutting is mainly a process of chip formation resulting from crack initiation and propagation or crack interaction for multi-tool cutting. This process can be simulated by using the well developed fracture mechanics criteria coupled to numerical methods. Fracture toughness is shown to be an important and useful parameter in quantifying cutting performance and in designing cutting tools. The paper concludes with discussions on the dynamic effects involved in rock cutting processes which should be taken into account for optimum cutting efficiency and tool design.

Jan 1, 1992

By Peter Altounyan

Goedehoop Colliery in the Witbank Coalfield of South Africa produces some 8 million tonnes of coal from fully mechanised room and pillar mining methods, using resin anchored bolts as roof support. Investigation of the quality of the installed bolts resulted in the finding that it was possible to pull out fully encapsulated roofbolts. This led to a drive to improve the quality of installation by making it easier to install a roofbolt correctly and more difficult to install incorrectly, whilst at the same time achieving high bond strength. The method of installation which was investigated, developed and implemented is known as 'spin to stall.' The roofbolt is pushed through the resin capsule to the top of the hole and then spun to mix the resin, until the increasing resistance to rotation exceeds the breakout limit on the bolt torque nut. The nut then runs up the bolt thread and is tightened to the roof as the drill stalls. This procedure is simple and avoids human factors such as non adherence to 'spin' and 'wait' times which contribute to poor installation with conventional methods. However spin to stall installation has been avoided in the past because of concerns over damage to the resin bond. This paper reports on the efforts made to investigate and understand the factors involved, and the progress made in overcoming the problem of resin damage so that the advantages of this installation method can be realised.

Jan 1, 2003

By Kot Unrug

The selection of tensioned versus non-tensioned roof bolts, for primary coal mine roof support, has been debated for well over 25 years. The wide spread use of fully grouted rebar marked the beginning of the discussion of the relative importance of bolt tension and the resultant immediate roof compression. The focus is on roof conditions encountered in coal mines however the discussion may be extended to hard rock mines as well. The theoretical bases for both systems are presented, with the analysis focused on the bolt's ability to actually fulfill the theoretical assumptions. Of specific concern are assumptions about bolt tension upon installation and the likelihood of maintaining useful bolt tension over time. The usefulness of tension roof bolting is limited by the mechanical interaction of roof bolt assembly and the rock, which may be valid at the time of installation only. Ambient mine atmosphere and fluctuation in moisture content changes the physical condition of rock, which may have a significant impact on the effectiveness and longevity of bolt tension. Changes in the material properties of the surface of the immediate roof can invalidate the assumptions, which were made in the design stage of roof support system. This means that the roof support in the long term excavations may be inadequate requiring costly rehabilitation. The presented arguments are illustrated with the examples of some relevant experimental data. Tension primary roof bolting is recommended where the immediate roof is: ? Stiff with a high modulus of elasticity ? Surface layers are continuous and fairly thin ? Not easily weathered

Jan 1, 2004

By John L. Hill

Cutter roof failure is a specific type of ground control problem which frequently results in massive roof failure. It is a cannon occurrence in coal mines of the Northern Appalachian Coal Sasin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure togain a basis from which to prevent its occurrence and to support such roof when failure does occur. Research conducted in a coal mine of central Pennsylvania has revealed a correlation between the occurrence of clastic dikes and fonation of cutter roof failure. Inmine mapping of ground conditions showed an increase in roof failure in areas of high frequencies of clastic dikes. Rock pressure monitoring around clastic dires registered the greatest amount of roof loading near the inter- section of dikes with the rib. Load cells measurim horizontal pressure changes in the roof indicated that the greitest pressure changes were occurring perpendicular to entry headings when clastic dikes were present. Analysts of rock pressure nwnitiring shows that the roof behaved as two cantilever beams when severed by a clastic dike. Additional roof supports such as trusses and cribbing were found to effectfvelv suooort the roof in areas of clastic dikes and prevent cutter roof iailure. However, there lnethads were only successful when employed shortly after mining.

Jan 1, 1984

By Erdal Akyol

The rockbolting method of support is employed widely in several countries in different of mines. Hard rock mines use this method extensively. Soft rock mines, such as coal mines, have employed standing supports (steel sets) as the main method, although some countries such as the U.S.A. and Australia have preferred rockbolting. There is increasing interest in extending the rockbolting method in coal mines. The application of rockbolting techniques in an industry which traditionally has not applied such techniques, has required the development of a systematic design approach. This design approach uses extensive monitoring, to asses the viability of the support system in differing conditions. Currently at a number of new and existing mine developments in the U.K., rockbolting is being successfully applied. Although, inevitably some localised geotechnical problems have been encountered and have needed to be taken into account. The effect of faulting on roadway conditions is discussed in this paper and a design approach has been applied using a numerical analysis method, namely the Finite Element Method. The results presented in the paper serve as a useful guide to roadway support designers, and in particular the role played by different bolts in a range of conditions.

Jan 1, 1992

By B. G. D. Smart

The development of a softwood alternative to the hardwood chockpiece used to build the waste-edge breakers commonly incorporated in gateroad packs is described. The results of laboratory tests on softwood prototypes and two underground trials are presented. The results of the last trial suggest that a viable alternative chockpiece has been designed, offering advantages over availability of wood, weight and given reduced wood content, price.

Jan 1, 1992

By S. M. Hsiung

A model (support selection model) for the selection of suitable types of powered supports under various geological conditions is proposed. This model is developed by evaluating the support, performance under different roof conditions at longwall faces in terms of five controlling parameters: (1) roof Falls, (2) front abutment pressure, (3) Face convergences, (4) gob materials entering into working area, and (5) roof caving line. This model suggests that more than one type of powered support. may be used under the same roof condition and the best selection should he based on the magnitude of suitability index of each support- type. The development and application of suitability index arcs discussed. Fourteen panels in seven coal seams are discussed in the paper to illustrate the applicability and effectiveness of this model. A roof classification system at longwall faces developed specifically for the construction of the selection model is also discussed. A simple example fur determining roof classification index is given.

Jan 1, 1988

The formation of tension cracks in slopes is well known. Analytical studies require the determination of a critical slip surface for any slope and, in doing so, it is necessary to consider an appropriate tension crack. A general yet simple approach is proposed for identifying the critical slope failure surfaces associated with critical tension cracks. The minimum factor of safety consequently reflects both safety against shear sliding and tensile failure. In general, the critical slope failure surface for a slope determined in this way differs from that which is obtained without optimizing the position and depth of the tension crack. In particular situations, the difference is significant.

Jan 1, 1989

By Keith D. Koper, Kris L. Pankow, Derrick J. A. Chambers, Michael K. McCarter

"In a mining environment, high quality seismic event catalogs are often useful in interpreting local stress states and identifying areas with elevated ground control risk. Installation, operation, and maintenance of local/in-mine seismic networks, however, may be prohibitively expensive, and mine operators may not anticipate the need for seismic data until unusual mining conditions arise. If regional, generally public, seismic instrumentation could be used to reproduce the results generated by local/in-mine instrumentation to an acceptable degree of fidelity, it would be a valuable and inexpensive tool for mine planners and ground control engineers.In this study we apply subspace detection—a non-traditional seismic event detection technique—to data from a sparse, regional network. The process is employed to identify mining induced seismicity (MIS) from an underground coal district. The results are compared to a seismic event catalog produced by a local seismic array operating within the permit boundaries. Additionally, we analyze the performance of two different stations of the same sparse, regional network in identifying blasts at a surface coal mine for which we have a detailed blasting log. In both cases data from stations between 10 and 60 km away from mining activity are used. We also explore the trade-offs between the number of detections and the number of false positives, which is influenced heavily by detection thresholds and the number of stations used in the process.For the surface mine we are able to identify more than 90% of the production blasts documented in the blasting log. We also find that the detected blasts from each of the four active pits produce waveforms similar to one another. The results are not dependent on source-receiver distance, and by requiring detections to occur on both stations the number of sure false positives is reduced to zero. In the underground mining district we identify between 30% and 75% of the events detected by the local array, depending on the acceptable number of false positives and the source-receiver distance. We also find many events that were missed by the local array, showing that regional subspace detection can usefully augment traditional local catalogs. Moreover, subspace detection can provide an estimate on event location and classification using data from as little as one seismic station."

Jan 1, 2015

By D. F. Howarth

Two innovative ground reinforcement products have been developed for use in the mining industry. One of these products is a high strength polyethylene (HOPE) bar for use as a rib bolt in underground coal mining and as a corrosion proof tendon in open pit mines. The other product is a cable bolt (Ultrastrand) which demonstrates enhanced load transfer and is available in continuous lengths. Ultrastrand's exceptional in¬situ performance and versatility makes it ideal for mechanised installation in both underground and surface mining operations. Details of these products are presented and results from labortaory and field trials are discussed.

Jan 1, 1992

By John Feddock

This study deals with underground mines and ground control and the prediction of seats strength characteristics based upon ultrasonic logging. Exploration drill holes, both rotary and core holes are used for proving coal reserves and determining mining parameters. Drill hole cores can be subjected to geologic study and geotechnical evaluation. In addition, the use of geophysical logging techniques is well established in determining certain strata characteristics and ground parameters. Since the characterization of the rock mass in mines remains insufficient in most cases, the idea of possibly characterizing the strength parameters without expensive core retrieval and laboratory testing is very attractive. The elastic properties of the rock can be deduced from measurement of the sonic velocity if the density is known. Through the use of in-hole geophysical density logging combined with an ultrasonic logging tool, the estimation of strata properties is possible. An investigation was conducted at two Indiana underground coal mines using geologic logging, geophysical logging, ultrasonic logging and laboratory strength testing to establish the strength properties of the roof rock. A specialized ultrasonic logging tool with one transmitter and two receivers enables nearly continuous readings along the length of the hole. The results of correlating portions of the data are presented. It is anticipated that the ultrasonic logging will be a supplemental tool for extending laterally the strata characteristics obtained from the existing program to surrounding areas. This may be obtained from the relatively inexpensive logging data obtained by ultrasonic logging.

Jan 1, 2003

By Ross Seedsman

There are many models for how roof bolts behave, one of which is prevention of shear along bedding. The basis of this model is that a roof beam will not delaminate if bedding parallel shear can be prevented. A key point in such a model is that bedding discontinuities are present naturally in the roof and that mining induced stresses do not generate new surfaces. The presence of these discontinuities means that the rock mass must be modelled as a transversely isotropic material if continuum codes are used. A limit-equilibrium type design method for specifying roof bolts is being developed using voussoir beam and excess shear force concepts. The method incorporates much of what operators know intrinsically about roof reinforcement, and allows mining engineers to focus on the key uncertainty - the frequency and location of bedding surfaces in the immediate roof. Areas where more research is required are highlighted.

Jan 1, 2000

By Ismet Canbulat

The cut out distance in the continuous miner sections in South African collieries is limited to 12 m. However, this distance can be extended to 24 m by the permission of the Department of Mineral and Energy (DME). This paper investigates the risk of roof Calls associated with the extended cut out distances permitted by the DME. Extensive underground experiments have been conducted using sonic probe extensometer under various geological conditions to identify the effect of cutting distance and tinge on the stability of the workings and the performance of the support. The results showed that that the most critical parameter with respect to ground control aspects of extended cut out distance is the bord width, which determines the amount of deformation that will take place in the roof. This was confirmed by the numerical modelling. The results also showed that a significant portion of the maximum deformation in the roof takes place before the ratio of cut out distance to bord width exceeds two. This indicates that once the face is extended more than twice the bord width, the roof will stabilise, assuming that no geological discontinuity is present and that there will be no further geometrical changes in the area as a result of for example the development of an intersection.

Jan 1, 2000