Search Documents

By B. J. Scheiner

A ferrous chloride-oxygen leaching system was investigated by the Federal Bureau of Mines as a means of re-covering copper and silver from a sulfide concentrate that had been pretreated to remove a majority of the antimony. The pretreated concentrate contained Cu, Ag, Pb, Zn, Sb, and As. Parameters affecting metal extraction, such as temperature, pressure, amount of ferrous chloride, and initial hydrogen ion concentration, were studied. Copper extraction of 98 pct was achieved by leaching 4 hours at 40 pounds per?square inch gage (psig) and 1000 ?C. Copper was recovered from leach solutions by cementation with iron, and the resulting ferrous chloride was recycled. Leaching the residue with cyanide followed by electrowinning recovered 99.7 pct of the silver. Iron, Sb, As, Pb, and S reported to the tails.

Jan 1, 1978

By R. H. Weiland

The dewatering of flocculated clay suspensions by compression in a centrifugal field has been investigated. The results are evaluated with regard to both direct applicability to centrifugal dewatering, in solid-bowl centrifuges for example, and indirect applications to gravity sedimentation systems. It is well known that sediment consolidation under gravity depends on structural characteristics such as permeability and on the "self-weight" of overlying sediment layers. An important objective of the study has been to evaluate the self-weight effect using centrifugal forces to simulate consolidation in deep sediments. In this way, small-scale laboratory tests can be used to predict the rates and limits of sediment compression in industrial systems such as thickeners and settling ponds. Experiments have been conducted in which the sediment mass and initial structure were maintained constant while the effective sediment weight was varied by centrifuging at different speeds. The effects of initial structure have also been studied using controlled variations in flocculation conditions.

Jan 1, 1993

By M. Beale

Fuzzy logic and neural networks are new technologies being applied in many areas of engineering and business. While it is not always clear which kinds of problems are best suited to these technologies, and which problems are best approached with more standard methodologies, both fuzzy logic and neural networks appear to show great promise in the field of control systems. This paper demonstrates two advantages that these technologies offer: Easy controller design in the absence of a mathematical model of the plant to be controlled, and adaptive control capable of quickly responding to changes in the plant.

Jan 1, 1994

By William A. Turcotte

Introduction The need for water is fundamental to every minerals processing operation. Though this may sound rather elementary, it is one area that cannot be over- looked. Frank C. Quinn in his paper entitled "Water Is Water Is Water" (1967) said, "but it isn't as simple as that. Very often research is slowed down and production is hampered because of a lack of appreciation for the behavior of water." The quantity of water needed for any operation is determined from bench and pilot plant testing. The quality required by the process for both fresh and reuse water is also established during these two testing phases. Quinn's statements are true whether the process involves the paper industry, the minerals industry, or any other industry. It is not the author's intent to cover water quality, quantity, or re- cycle in specific terms, but to provide the reader with a general outline of the topic with reference to several valuable sources of information. The first part of the chapter will cover several of the areas that have been de- tailed by others and also provide a list of reference sources. The references at the end of the chapter are not all inclusive but will provide a good starting point. In the second part of the chapter, a detailed description, with flowsheet illustrations, is pro- vided on the evolution of the reclaim (reuse) water system at the Tilden concentrator. Mineral Industry Water Needs Beresford and Edler (1978) surmnarized the minerals industry's need for water this way: "minerals are necessary to a modern complex technological society. The minerals industry, while its water needs are relatively minor compared to large users such as agriculture, nevertheless requires a large quantity of water to carry out daily operations from mining to final product refining." In 1973 total water use in the United States was estimated at 15.14 billion cubic meters (4 trillion gallons) for the minerals industry. Of this, about 69% was recirculated within the system. In 1982 Watt and Horton stated that the percent of recycled water in the minerals industry had improved to 73%, showing the minerals industry is an efficient user of water and that steady improvement in water recycling is something the minerals industry can look to with pride. The percent of water needed by the United States' minerals industry was estimated in 1962 to be about 2% of the total water required by industry

Jan 1, 1986

By T. W. Camm

One function of the U.S. Bureau of Mines is assessing potential economic impacts of federal land withdrawal policies. This often requires performing economic ana1ysls for an area with limited geologic information available. Input to the economic decision process relies heavily on estimates of mine and mill costs for the potential resources in the area being considered. A methodology for performing these cost estimates was needed to address this situation.

Jan 1, 1992

By Joseph W. Siefke

The Kramer borate deposit is located in the western Mojave Desert at Boron, California, about 100 miles northeast of Los Angeles (Figure 1). The deposit derives its name from the district in which it lies. Borax (Na2 B407.10H2O) is being mined from the Boron open pit to serve a major portion of the United States and world borate markets. This paper deals primarily with those geologic factors which affect slope stability in the overburden at the Boron open pit. Discussion includes slope failure history, slope monitoring techniques and the results of a dipmeter survey of overburden structure. Open pit mining was begun at Boron in 1957. The initial pit was successfully excavated at the recommended 1.5:1 (horizontal to vertical) slope in the overburden. During pit expansion in 1962, excavation of the overburden exposed beds dipping into the pit at +15 degrees and numerous high angle fractures associated with two intersecting fracture systems, the West Jenifer and Portal fault zones. Ensuing south and east wall failures indicated the need for more structural information in the arkose to establish better wall design criteria. Barnard and Kistler (1963) recognized that the many facies changes, faults and other variables in the Boron overburden make it extremely difficult to reduce prediction of slides to a simple arithmetical formula. Despite the difficulties and uncertain¬ties, special programs such as surface resistivity, refraction seismic and core drilling were conducted in an attempt to predict slope stability conditions and to gather geologic information. These early efforts while helpful, did not provide the necessary details of bedding orientations and fault locations which are of paramount importance in our slope stability program. A dipmeter survey in 1974 successfully measured these variables and data from that survey are instrumental in the design of slopes currently being excavated.

Jan 1, 1976

By H. L. Monroe

Meramec Mining Company, owned 50% by St. Joseph Lead Company and 50% by Bethlehem Steel Corporation,- is engaged in the mining, concentrating and pelletizing of iron ore from the Pea Ridge Mine which is located in the rugged, wooded Missouri Ozarks about 15 miles from the town of Sullivan or 75 miles southwest of St. Louis. The orebody was delineated in the middle 1950's by the St. Joseph Lead Company during the Company's intensive exploration program to discover new lead orebodies to replace the declining reserves of the famous Southeast Missouri Lead Belt. An airborne magnetometer survey was run by the U.S. Geological Survey, the Missouri Survey and several mining companies, (of which St. Joseph Lead Company was the principal supporter). The survey was published in 1950 and disclosed an anomaly in the vicinity of Pea Ridge. In 1950 test drill holes disclosed that under some 1300 feet of sediments there did exist an iron deposit of probable commercial significance. No further action was taken until 1956 when additional drill holes confirmed beyond reasonable-doubt-that this was a major iron ore discovery.

Jan 1, 1965

By G. Bonifazi

In the present work the possibility to utilize the morphometrical and morphological characteristics of an articulate solids system in a slurry flow to monitorate and to control a continuous process is considered. This goal has been reached by mean of an optical system able to acquire, to handle and to process the pictorial information derived by a suitable hardware architecture designed to realize the best lighting, focusing and sampling conditions for the examined flow stream domain. The procedure has been tested using different flow stream slurries coming from different sections of a beneficiation plant. A suitable strategy and a consequent software architecture has been set up in order to assure to the system the necessary speed and the stability to achieve correct on-line measurements and control.

Jan 1, 1994

By Edgar A. Scholz

The purpose of this paper is to make a comparative cost analysis of domestic and foreign exploration projects which developed into mines during the 1960-1974 time period. A total of 18 mining companies, American and Canadian, were approached to solicit cost data on domestic and foreign exploration projects which developed into mines. Only 20 percent of the companies to which questionnaires were sent made data available. Several companies answered negatively, informing us that they would have difficulty in attempting to sort our costs. Some companies were usable to release cost details. It is comforting, however, to realize that some of the non-contributing companies expressed eagerness to hear the findings of this paper. Inasmuch as the data available on exploration expenditures is, in some cases, somewhat uncertain and that no two mining companies follow the same system of cost allocations, the results obtained in this analysis should he interpreted as trends of a general character.

Jan 1, 1976

By James Douglas

For the past several years, inflation has placed increasing pressure on our economic system. The total effect of inflation is complex when combined with other factors which affect the economics of equipment. A mathematical model is described herein which can be programmed on a computer to determine the effect of inflation on economic life and profits after taxes. The computer output results in graphic plots which clearly show the relation of various percentages of inflation to life and profits. Inflation has become a common topic of conversation in the recent past. What is it and how can it be measured? What effect does increased inflation have on equipment policy? Research now in progress at the Construction Institute at Stanford University is beginning to unravel some of the mystery of inflation. As a start, let us answer the first question by defining the word inflation. The dictionary says that inflation is "an increase in the volume of money and credit relative to available goods resulting in a substantial and continuing rise in the general price level. It appears, in fact, that we are in an inflationary spiral which is "a continuous rise in prices that is sustained by the tendency of wage increases and cost increases to act on each other." 3 Inflation behaves just like compound interest. It takes more dollars of future years to buy an equal amount of a given commodity, be it a material or a service. Let us assume an annual inflation rate of 5 percent. Assume that 1Associate Professor of Civil Engineering, Stanford University, Stanford, California. 2Webster's Seventh New Collegiate Dictionary, Springfield, Mass., G. and C. Merriam Co., 1969. 3Ibid.

Jan 1, 1972

By J. P. McKinney

Benchtop experiments were performed, in which an electric field was used to enhance separation of water from phosphatic clay suspensions from a central Florida mine. A constitutive relationship was established that relates the increase in solids content to operating time and the applied electric field. An upper limit to the degree of separation was found to be a function of electric field, and the time required to achieve this limiting value was also a function of electric field. The energy requirement for removal of water ranged from 1.25 to 175 Wh/kg water removed as a function of the electric field. A mathematical model was developed that provided good agreement to the experimental values and served to validate the constitutive relationship.

Jan 1, 2011

By G. D. Naugle

Deep open-pit mines invariably affect the local and regional hydrologic systems. Pit dewatering, occurring during mining operations, puts an obvious hydrologic stress on these hydrologic systems. However, post-mining hydro-logic impacts resulting from the pit refilling with ground water following the cessation of mining activity can also be significant. Prediction of the rate at which the post-mining pit will fill with ground water is a critical aspect of assessing such long-term hydrologic impacts. Numerical ground-water flow modeling prov1des a method that can be used to predict the rate at which pits will fill with ground water.

Jan 1, 1992

By Frank A. Aplan, Barbara J. Arnold

INTRODUCTION Coal flotation is a fine cleaning process usually present in all but the older preparation plants. It is typically used to clean either the -28 mesh (-500 pm) or - 100 mesh (- 150 pm) raw coal fines, and it is the only commonly used preparation method that can effectively recover coal particles finer than, say, -200 mesh (74 pm). To place coal flotation into its proper context, it should be noted that the bulk of the raw coal sent to preparation plants is treated by gravity concentration. On a worldwide basis, from 0 to 40% of the raw feed to a preparation plant is treated by flotation, while in the US only about 10% of the raw coal feed is floated. Roughly, 50% of US preparation plants use flotation to process at least a portion of the raw coal feed, although most of the newer plants incorporate flotation into their flowsheet. Historically, the process has only been used to treat the raw coal fines naturally occurring after mining and a minimal amount of crushing at the preparation plant. This is in sharp contrast to ore flotation where, typically, the entire tonnage is first ground and then floated. As a consequence, of the approximately 500 Mt of raw coal treated by preparation in the US yearly, it is estimated that only about 40 Mt are sent to the flotation circuits (producing -30 Mt of clean product).'O1 This small tonnage compares with about 400 Mt of ores treated annually in the US by flotation. By analogy to ore flotation, where it is an effective, large tonnage, low cost, easy to operate process, its potential in coal preparation should be great. Reasons why it has not achieved a greater potential in coal preparation have been attributed by Aplan 102 to: 1. Indifferent results in removing sulfur and ash. 2. Difficulty in floating low rank and oxidized coals. 3. Inability to make clean separations with the finer sizes. 4.Inability to clean slurries with a high percentage of clay. 5. Problems with water chemistry. 6. Competition with effective, gravity coarse-cleaning methods. 7. Low value of coal historically. 8. Dewatering problems. 9. Transportation and storage problems with coal fines. 10. Marketing problems with coal fines. 11. Inadequate attention to the process in the plant. 12. Inefficient use of capital and operating monies. Inadequate attention to procedures, machines, and processes.

Jan 1, 1991

By Jiang Su, Alan Bloodworth

"Composite sprayed concrete lining (SCL), consisting of two layers of permanent sprayed concrete separated by a layer of spray-applied waterproofing membrane, represents the latest development in SCL tunneling, but presents several challenges to designers. This paper aims to address the following issues: (1) how to simulate composite action, (2) behavior of a composite SCL tunnel, and (3) how to utilize composite action to achieve lining thickness efficiency. It firstly sets out the background to the composite SCL concept, and then presents a strategy for numerical investigation. The main part of the paper is the presentation and discussion of the simulation results, focusing on the lining deformation, load sharing and the safety margin of both linings. Interface stresses are also examined. It is found that significant secondary lining thickness reduction may be achieved by utilizing composite action. Challenges for the design of composite SCL tunnels are briefly discussed at the end. INTRODUCTION Sprayed concrete lined (SCL) tunnelling has seen rapid development over the last twenty years in the UK (Su 2013). One of these developments has been the replacement of traditional sheet membrane and cast in situ secondary lining with innovative spray applied waterproofing membrane and sprayed secondary lining system, which has been adopted in recent major projects, such as Crossrail (Pickett 2013), and brings many benefits to the construction (Dimmock et al. 2013). The combination of sprayed primary lining, spray applied waterproofing membrane and sprayed secondary lining is perceived to provide a structurally efficient lining system that outperforms the traditional lining system, which consists of sacrificial primary lining, sheet waterproofing membrane and cast in situ secondary lining. The claimed benefits in structural performance arises from the composite action between the sprayed primary and secondary linings via the spray applied waterproofing membrane, which produces a much stiffer cross-section and therefore a more efficient use of materials. Early investigations on the design of composite SCL tunnels were carried out without (1) definite and reliable long-term interface parameters, (2) a verified numerical modelling technique, or (3) consideration of different stress histories between primary and secondary linings (Thomas and Pickett 2011, Marcher et al. 2011). This paper reports the findings from a numerical parametric study on a typical composite SCL tunnel with varied secondary lining thickness. The results show that the true benefit of composite lining arises from the optimisation of the lining thickness (stiffness) ratio between the primary and secondary linings to achieve secondary lining safety and thickness efficiency at the same time."

Jan 1, 2016

By L. A. Price

With increased stripping ratios and with dwindling ore content, the mining fraternity is increasingly turning to larger and larger equipment for profitable open pit operations. The availability of higher horsepower prime movers and increased capacity electric transmissions using either wheel mounted or axle mounted traction motors makes a reality of single axle, rear dump trucks having 150 to 250 ton capacity. The size of electric loading shovels is inherently geared to the size of haulage equipment. To work effectively with this new generation of trucks, the Harnischfeger Corporation has introduced its P&H Model 2800 with a capacity of 20 to 25 cubic yards and a working weight of nearly 1,500,000 pounds. The Model 2800, depicted in Figure 1 loading a 200 ton truck, has many new electric and mechanical features designed to give excellent production and low cost operation. Chief among the new features is the ELECTRO TORQUE* control system. ELECTROTORQUE is a completely static, solid state electronic system supplying controlled power both to the armature and to the fields of the d.c. shovel drive motors. It eliminates many major electrical rotating machines and their attendant maintenance. The system was developed jointly by ASEA of Sweden and Harnischfeger Corporation.

Jan 1, 1969

By M. Karmis

According to international projections and future energy scenarios, coal will continue to be a prominent fuel for the next 25 years. In fact, in many regions around the world, coal is expected to dominate the electricity sector until the year 2030. At the same time, with instability and volatility of oil prices, coal is also positioned as an alternative feed stock for conversion into liquid fuels. Energy economists maintain that coal liquefaction is viable at crude oil prices of $35 or more per barrel. Depending on technology and coal composition, 1 ton of coal can produce 1 to 4 barrels of oil. Increased coal production and the expanded utilization of coal also raise environmental concerns regarding greenhouse gases and the problem of handling CO2. Carbon sequestration research, currently conducted in many parts of the world, has demonstrated considerable potential for C-storage in unminable coal seams. Such geologic storage, when possible, can also be integrated into an enhanced coal bed methane recovery process Can coal fuel power plants and industrial facilities, provide diesel and other liquids and, at the same, also be used as a medium for permanently storing CO2? This presentation will provide a global perspective on these questions and stress on the need to reconsider, or even redefine, coal as the fuel for the future.

Jan 1, 2006

By M. J. Hughes

Kaiser Steel Corporation's Eagle Mountain operations are located in Southern California at a distance of about 130 miles east of the Corporation's steel plant at Fontana, California, and at a distance of about 225 miles from the nearest harbors which are located at Long Beach and Los Angeles, California Although the Eagle Mountain ore bodies are strategically located with respect to the steel plant and the harbor facilities, they are not of a very high grade and 'the geologic nature of the deposit makes it very difficult to mine and to concentrate. The iron ores occur as partial replacement of older zones mainly within dolomites and to a lesser extent within quartzites and quartz monzonites. The alteration was extremely variable and generally resulted in the formation of pyritic magnetic which, in part of the ore body, was leached to remove the pyrite and change the magnetite to hematite. Although the overall ore body is large, a major portion of it contains sulfur in the range of 1.0% to 5.0%. Obviously, this is too high a sulfur content for direct use in blast furnace feed.

Jan 1, 1968

By Armando Alatorre

The Republic of México is the world's largest producer of celestite/strontium carbonate and natural sodium sulfate. It is also a significant producer of flourspar, barite, graphite, sulfur, feldspar, salt and gypsum. New production may be brought on stream for borates, wollastonite, garnet, calcium carbonate and others. The country covers a geographic area of approximately 2 million square kilometers (760,000 square miles), and is divided into seven geological/geomorphological provinces. Less than 20 percent has been explored in detail for either nonmetallic or metallic minerals. This leaves large areas available for the discovery of world-class industrial mineral deposits. In addition to new deposits of those minerals currently being produced, there is exploration and development potential for borates, magnesite, rare earths, nepheline syenite, heavy mineral sands and numerous others.

Jan 1, 1995

By Richard B. Muter

1. Coal Preparation Terms (General) 1.1 Coal preparation-collectively, physical and mechanical processes applied to coal to make it suitable for a particular use. 1.2 Run of mine (ROM coal)-coal produced by mining operations, before screening, crushing, or preparation. 1.3 Raw coal-coal that has received no preparation other than possibly screening or crushing. 1.4 Raw coal feed-raw coal supplied to a plant or machine, in which it undergoes some form of preparation. 1.5 Coal cleaning-the treatment of coal to lower the mineral matter content (ash). 1.6 Cleaned coal; clean coal-coal produced by a cleaning process (wet or dry). 1.7 Middlings-a product of coal preparation that, by reason of its ash content, is intermediate between coal and discard. It follows therefore that the relative density of middlings is intermediate between those of coal and discard. Middlings may be reprocessed. 1.8 True middlings; bone comparatively high ash particles so nearly homogeneous that their quality cannot readily be improved by crushing and recleaning. 1.9 False middlings; interbanded middlings-middliigs in which the particles consist of bands of coal and shale, and from which the coal may be liberated by crushing 1.10 Refuse-waste material in the raw coal which the cleaning process removes. (See also discard; dirt; stone, No. 1.12). 1.1 1 Reject-the material extracted from the feed during cleaning, for retreatment or discard. 1.12 Discard; dirt; stone--the material extracted from the raw coal and finally discarded. 1.13 Recirculation-the operation in which the whole or part of a product from a process is returned to the feed to the process, e.g., the return of the crushed overflow from a screen to the screen feed for rescreening. 1.14 Foreign coal-coal received at a preparation plant from a colliery other than that to which the plant is attached. 1.15 Imported coal-coal coming from a foreign country, or other state within the country. 1.16 Low-grade coal combustible material that has only limited uses owing to undesirable characteristics (eg., ash content or size). 1.17 Segregation-partial separation of a previously mixed material into its constituents, occurring as a result of differences in either particle size or relative density. 2. Cleaning Characteristics 2.1 Washability-amenability of coal to improvement in quality by cleaning. 2.2 Float-and-sink analysis-the division of a sample into relative density fractions with defined limits, the proportions of the fractions being expressed as percentages of the total sample, commonly with an indication of the ash percentage (and other characteristics, if required) of each fraction.

Jan 1, 1991

By Kenneth G. Colman

Even though wet processes were used in coal preparation plants prior to 1941, dewatering coal was not a problem then because the finer sizes were uneconomical to recover and were considered waste. However, during the war years the scarcity of raw materials necessitated the utilization of every pound of natural resources and coal plants began seeking an economical mans of recovering fine coal. Early efforts to this end concentrated primarily on centrifugal dewatering devices. Such equipment produced good results but was relatively expensive. In 1944, a method was devised utilizing a vibrating screen fitted with a profile wire deck rather than the standard woven wire cloth deck. This machine came to be referred to as a dewaterizer. Results obtained with the dewaterizer approached those of the centrifugal equipment, but at a lower capital cost, Their use reduced either the number of centrifugal units required to follow the dewaterizers or the required energy input to heat dryers, In some cases they eliminated the need for any further dewatering equipment.

Jan 1, 1970