Search Documents

By J. P. Fitzgerald

This paper is an accumulation of information on the geology, mineralogy and mining of the Hectorite clay deposit owned by NL Chemicals (U.S.A.), Inc. The mine is located in San Bernardino County, California approximately 35 miles east of Barstow and 1-1/2 miles south of U.S. Highway 40. The region is known as the Mojave Block which is a region bound by the San Andreas fault zone to the southeast and the Garlock fault zone to the North. The faults of both zones are active, vertical faults along which movements are mainly horizontal. Most of the faults within the Mojave Block are high angle faults which trend northwest. They are considered part of the San Andreas fault system and are a result of the right- lateral movement characteristic of this system. The east-trending faults are also high angle faults, along which movement has displaced rock units vertically. Manix fault is the only mapped fault that shows evidence of left slip which is characteristic of the Garlock sys tem to the North.

Jan 1, 1986

By V. I. Lakshmanan

Crystalline Flake Graphite is a strategic mineral. Since 1954 nearly all North American consumption has been imported from offshore. The Bouthillier Project in Quebec, Canada, is Orrwell Energy's bid to enter the market. Milling of flake graphite is considered easy, yet more problems have been encountered in flowsheet and plant design than in most other minerals. A fresh approach to existing technology was taken, giving results that are highly satisfactory. The key to graphite liberation without flake deterioration is found to be in autogenous grinding. In addition to producing marketable coarse graphite by such autogenous grinding, flotation and tabling, super purity fines can be produced using repeated regrinding, elutriation and flotation. This paper discusses the design of a 500 TPD plant based upon the results obtained from bench and pilot plant studies.

Jan 1, 1984

By W. C. Morgan

The Federal Surface Mining Law enacted in 1978 is now being translated into regulations which must be followed in future coal mining. Substantial change to mining procedures is required to maintain stricter air and water control while mining and to return the mined out land to equal or better use than before. These changes do not come easy; and in most cases, they create a substantial additional cost. Based on field observations and mining studies, Caterpillar has been making suggestions on the use of their types of equipment to conform to the new standards at the least cost. This paper will be a brief review of some of the overburden stripping and reclamation methods suggested by Caterpillar. A production and cost comparison of dragline, scraper/dozer and truck, loader systems in 20 to 150 ft. Overburden conditions illustrates potential cost savings using mobile equipment.

Jan 1, 1980

By Trevor R. Ellis

In this paper a method is presented for estimating the specifications of sandstone-type uranium deposits which will be the minimum that can meet a company's economic requirements for investment. The method interpolates and extrapolates from available cost data for typical mines to provide the costs for a wide range of possible deposits. The range of deposits achieving the company's required discounted cash flow rate of return on investment at an estimated uranium oxide selling price is then calculated, thus giving the complete range of deposits which meet the minimum required specifications. Prospects are then evaluated by comparison with these minimum requirements.

Jan 1, 1979

By A. K. Sinha

A great potential market for the high BTU midwestern thermal coal exists if the coal is desulfurized and prepared to meet the environmental restrictions and the utility customer specifications. Because the midwestern coal is very high in pyritic sulfur, it can be adequately desulfurized by removing the pyrite with the help of such coal cleaning techniques as the froth flotation. Froth flotation cells are now commonly employed in modern coal preparation plants for recovering the fines but they are not utilized for desulfurizing the coal probably due to a lack of system operating data for such applications. A research project recently conducted at Southern Illinois University shows that the total sulfur in the midwestern coals can be successfully reduced from as high as 5.3 percent to less than 1.4 percent by single stage froth flotation. The results obtained on ten different samples of high sulfur coal obtained from different areas in the Illinois Basin are presented and discussed.

Jan 1, 1985

By M. Tomono

Harima Works is operating as the zinc and lead simultaneous smelter utilizing the imperial Smelting Process. The smelter commenced its operation in 1966 with designed capacities of 3500 t/M of zinc and 1500 t/M of lead. After that, owing to the results of progressive developments and improvements in operating efficiency and equipments, it has doubled its production figure. This report reviews our recent developments carried out from 1983 to 1985. Firstly, the furnace bottom design was modified for the purpose of reducing carbon consumption ratio. As a result, shaft operating condition has been satisfactory and carbon consumption ratio was improved by 2%, in addition, furnace zinc production was increased by about 8%. Secondly, the oxygen enriched operation at sintering machine was tested from July 1984 to June 1985, in order to increase the sinter productivity, and to solve the capacity imbalance between sinter plant and ISF. As the test result, it was found out that sulfur elimination rate was increased by approx 10% with the oxygen enrichment of 500 Nm3/hr.

Jan 1, 1986

By A. K. Sinha

Inspite of the growing demands worldwide, thermal coal must compete in the market both in price and quality. The design and performance efficiency of coal preparation plants is thus crucial to the survival and profitability of a coal industry. While the coal recovery influences the cost of production, the quality produced by a preparation plant determines the selling price. Several coal preparation plant simulation models have been developed in recent years to help Improve the performance of coal preparation plants. A research project was recently conducted at Southern Illinois University to evaluate the practical applicability of such a model. The results of this study are presented and discussed.

Jan 1, 1986

By Donald M. Keagy

How many times have you said or heard someone say, 'What are you doing right now?" And how many times have you heard the reply, "Breathing air!" Probably never, or at most only a few times in a facetious vein. Breathing air is absolutely necessary to sustain human life, and yet most of us take it completely for granted. Beginning ten to fifteen years ago there was growing concern on the part of the general public that pollution of the air is a threat to man's health and welfare. Concurrently much thought and effort was devoted to the task of defining and resolving the problem of air pollution. In the course of this effort it has become quite clear that our National policy in this regard should be founded upon three basic axioms: (1) Action should not be postponed until emergency conditions make it compulsory; (2) The air cannot be purified after it is polluted, and (3) Air pollution control cannot be accomplished without close cooperation among all levels of government, industry, and the public.

Jan 1, 1967

By Ole Bernt Lile

The well-known method of C. Schlumberger, Mise a la masse, has become a popular method again in ore exploration in Norway after many years of dominance by EM methods. The principle of the method is to place a current electrode within a conducting ore body and remove the other electrode to a great distance. (Figure 1). Often it is convenient to place a return electrode on each side of the area explored. The method is best suited for ores that have a conductivity contrast, relative to the host rock, of several orders of magnitude. The potential drop within the ore itself may then be neglected and the ore contact against the rock may be regarded as an equipotential surface. One may say that the ore body is electrically charged. Therefore, in Norway the method is now most often called the Charged Potential Method (abbreviated CP). The most usual way to present data obtained by CP, is to draw equipotential lines based on potential values measured in profiles on the surface. Such a potential map gives an immediate picture of the outcrop of the ore and also indicates disturbing conductors in the neighborhood. It may also be useful to look at the potential profile and its horizontal gradient along the strike axis of the potential map. These profiles may give information about the strike length of the conductor. Figure 2 shows the theoretical profiles of potential and gradient along the axis of the potential picture on the surface over a charged line plunging 15 degrees. It may be seen that the maximum of the gradient curve clearly indicates the lower end of the conductor. Figure 3 shows the corresponding pro- files over a charged line plunging 45 degrees. In this case, it is not possible to see an indication on the curve of the lower end. Only curve fitting could help interpretation in this case.

Jan 1, 1975

By M. C. Fuerstenau

Flotation data indicate that sulfonate and dodecylamine adsorb physically on Mn02 at ambient temperature. Oleate also adsorbs physically if the zero-point-of-charge of the Mn02 is sufficiently high. Chemisorption of oleate apparently occurs between pH 8 and 9, and this phenomenon is enhanced considerably at elevated temperature.

Jan 1, 1966

By C. A. Rowland

Autogenous grinding, defined as grinding with like material, while quite an old art has recently been revitalized. Two phases of autogenous grinding, primary and secondary, have been the subject of recent papers, technical articles and discussions. The purpose of this paper is to discuss a third phase of autogenous grinding - Intermediate Autogenous Grinding - comparing it to and indicating advantages over the other two phases. Autogenous grinding can also be called ?Rock grinding?1; that is, grinding using ore or rock from the same deposit as the mill feed as grinding media contrasted with using as grinding media steel rods, steel or ironballs, natural or manufactured iron, free pebbles, or other shapes and materials foreign to the mill feed.

Jan 1, 1964

By S. Acar

The results obtained for the selective flocculation or flotation of natural ores do not usually agree with the corresponding properties of the constituent minerals when present alone. This is mainly due to the presence of dissolved mineral species which can interact in many ways with other components in the system and alter their behavior. In this paper, the effect of dissolved species on the flocculation and electrokinetic properties of sulfide minerals is disscussed. Dissolved Fe, Cu and Ni species are found to affect the properties of chalcopyrite, pentlandite, millerite, pyrrhotite and covellite in certain pH range. These effects are interpreted in terms of species adsorption leading to activation or depression of reagents, surface precipitation and complexation of species, etc.

Jan 1, 1985

By Michel Gauthier

Several zinc showings, exhibiting many similarities to the well-known Balmat-Edwards zinc deposits of New York State, occur within the Grenville Supergroup strata of the Mont-Laurier Basin, Quebec. Metallogenic mapping programs have revealed much of the stratigraphic control of this mineralization. This control is observed on both regional and local scales. At the regional scale, these showings are confined to the perimeter of the Mt.-Laurier Basin, while at the local scale, a definite association between the zinc mineralization and dolomitic marble horizons is clearly exhibited from detailed mapping. These new exploration guidelines have proven to be useful for base-metal exploration in the Mt.-Laurier Basin and should be applicable to the entire Grenville Province.

Jan 1, 1983

By Ernst P. Hall

The Irwin Basin. (Fig. 1)* is a synclinal or shoe-horn *Figure numbers throughout refer to color slides not included with the preprint shaped basin in the Pittsburgh Coal Seam, It is approximately 10 miles wide and 22 miles long at its maximum points. The surface of the land above the basin is hilly, rolling farmland,, typical of this area of Pennsylvania, and it is criss-crossed with streams and highways and liberally dotted with farm houses and communities. In-general the coal is pitched from north to south with a total drop of 610 feet'. The coal seam cross-section from east to west is bowl-shaped and rises as much as 375 feet from the low point of the bowl to-the-outcrop. Cross-sections showing coal elevations are shown on Figs, 4 and 50 Ground cover above the coal will vary from 0 to 550 feet, averaging about 350 feet throughout the area. This area is richly endowed with a history of coal mining. The first car of coal shipped cast of the Allegheny Mountains was mined in the Westmoreland Coal Company's Shady Grove (later North Side) Colliery in Irwin, Pa., early in 1853, This mine was opened in 1852 by Coleman, Hillman & Company. The coal was hauled from the mine to the freight station by horse-drawn wagon and. loaded into a then "standard" box car of 18,000-pound capacity. Coal mining in this region flourished and grew as steel production in nearby Pittsburgh demanded more and more of the high quality, metallurgical-grade coal of the region.

Jan 1, 1959

By Robert Stefanko

The most perplexing problem that has confronted mining engineers since the dawn of mining has been strata control. For the purposes of this paper, strata control will be defined as control of ground in the immediate area surrounding the, mine opening. To prevent movement of the surrounding strata into underground mine openings, miners have traditionally relied upon some type of artificial supports placed within the openings and located in a manner determined by trial and error from previous experience. Without the means to measure changes of stress in the supports and within the mine structure itself, an evaluation of the efficiency of the supports and mining system was impossible. Strata control thus remained an art with very little application of science. During recent years a revolution has occurred in mining. The modern mining engineer is contented no longer-with trial and error methods but is utilizing all the technological information at his command to obtain a solution to this age old problem. However, serious problems have arisen due to the lack of certain basic knowledge in three important areas: 1, The original stress distribution within the earth strata prior to mining. 2, Redistribution and concentration of the original stresses with mining activity. 3. The properties of rock that are significant in failure and its prevention.

Jan 1, 1960

By Bennett D. Lass

A new method for determination of residual flotation oils on beneficiated kaolin clays has been developed. The method, which yields qualitative information, is based on fluorescence measurements employing a spatially resolved, polychromatic illumination source for excitation, and a two-dimensional detection scheme using a silicon-intensified, video imaging device. The method was used to identify residual oils on a beneficiated, Washington County, Georgia, crude clay. The results were compared to a similar qualitative analysis performed via capillary column gas chromatography using an FID detector. The video fluorometry was the preferred method of, analysis.

Jan 1, 1983

By F. M. Stephens

This paper is to be presented at the annual meeting of the American institute of Mining and Metallurgical Engineers, San Francisco, February 1959. Permission is hereby given to publish with appropriate acknowledgements, excerpts or summaries not to exceed one-fourth of the entire text of the paper. Permission to print in more extended form subsequent to publication by the Institute must be obtained from the secretary of the Institute. If and when this paper is published by the Institute, it may embody certain changes made by agreement between the Technical Publications Committee and the authors, so that the form in which it appears here is not necessarily that in which it may be published later.

Jan 1, 1959

By J. D. McAuliffe

The Homer-Wauseca Mine is operated by the Hanna Mining Company, three miles north of Iron River, Michigan on the Menominee Iron Range. The mine produces 5,300 tons of direct shipping iron ore daily. The present main producing level is at a depth of 1,500 feet below the collar. The ore body continues to a depth of 2,700 feet below the collar, to which depth the modern circular concrete shaft has been completed. A view of the property is shown in Figure #1. This paper is a report on the development of large underground boreholes used initially to conduct stope filling material into inaccessible, mined-out stopes. Later holes were drilled for ventilation raises, for mine drainage, for passageway for power cable, also for the primary breaking point for long hole stoping. Some, which were drilled as ventilation raises, were later stripped to a suitable size for a manway or ladder road. The holes varied in size from 6" to 30" with the present popular, economical working size being 16 1/4", used as a stope fill passage in mined out areas and for ventilation in deeper development. Foremost has been the desire to develop equipment suitable for drilling raises large enough for manways.

Jan 1, 1963

By Stephen Krickovic

"Bleeding", as used in mine ventilation language, has a number of meanings among mining men and is regarded with different degrees of importance. This lack of uniformity stems from a number of specific situations. A method that is adequate in a mildly gaseous mine may fall short in a very gaseous mine. Projected bleeders could be dependable under a certain type of roof, and totally unsatisfactory under a different type. Similarly a plan of bleeders can be rendered useless due to undulations of seam and water in one mine and function well in another. Finally, what is effective in a mining system with partial recovery will not suffice with full recovery. You may wonder, then, if there is a common denominator for the essential function of "bleeding". In my opinion, there is, and it can be defined as controlled movement of air across an active pillar line toward the back and outby ends of the adjacent gob area into the headings provided for the purpose. The objective is to maintain as methane-free as practicable a belt adjacent to the working places, so that, if face ventilation is interrupted temporarily, the gas will not accumulate in dangerous volumes at the working faces before ventilation is restored. It's possible for these temporary interruptions to be unnoticed in time or at all. In such cases, ineffective bleeding could cause a disaster. This has happened. To control, there must be power. That is to say, there must be adequate air, pressure differential between the front and back ends of a pillar line to facilitate proper regulation for diverting of air to the various portions of the gob and as far away from the active section as is practicable. As an indication of the importance of pressure, it is noteworthy that one may provide and maintain in a reasonably open condition a heading or two for a bleeder system and fail to obtain effective bleeding .because air pressure differential is inadequate. On the other hand, you are all familiar with the fact that pillar lines in some seams can be ventilated adequately by air flow straight across the gob when the section is near a main return shaft and thus obtains a heavy pressure differential.

Jan 1, 1962

By Y. J. Wang

The definitions of system pressure loss (mine head) and system resistance, which are traditionally associated with single-fan net- works, are applied to multiple-fan ventilation networks. The system characteristics -- relations among air power, pressure loss, air quantity and resistance -- are analyzed by introducing the concept of subsystems. These subsystems are associated with the fans located in a cutset of the network. For a multiple-fan network, the resistances for the subsystems and total system are dependent on the quantity ratios of the subsystems. In general the pressure loss of a subsystem or a total system does not vary as the square of the corresponding air quantity. If the quantity ratios of subsystems are all held constant, then the resistances become constant and the pressure losses are predictable from the quantities employing the "square law." The system resistance has a minimum value under the natural- splitting flow pattern. Being independent of the value of system quantity, the minimum system resistance provides a basis for comparing the different networks.

Jan 1, 1983