Search Documents

By Victor F. Hollister

Skam deposits considered as porphyry copper deposits have been classified into three basic prospecting models: (I) the skam deposit associated with a mineralized intrusive (Pima-Mission), (2) the deposit associated with a barren igneous stock (Ertsberg), and (3) mineralized rock that seems to have no clear association with apluton (Phoenix). Pima-Mission, Christmas, and many other copper-bearing skarns developed in carbonate sequences near mineralized intrusives form an important part of the deposit. Historically, copper derived from the mineralized intrusion accounts for less than half of the metal produced by most porphyry mines, as most mineralization occurs in the intruded rocks. Skam mineralization is an important part of wall-rock metal deposition, because carbonate sequences are preferentially replaced by sulfide and skarn minerals. Exploration for skam mineralization is an important phase of porphyry copper exploration. Impure carbonate beds can become better host rocks for skam deposits than pure carbonates, and these in particular should be included in porphyry-exploration programs if the impure strata are cut by the stock. Skam deposits can also form near stocks that are barren of sulfide. In this model, the two best ore guides are strata favorable for mineralization (usually impure carbonate beds) and the intrusive contact. Faults can also act as important ore controls. Some skarn deposits form that have no clear genetic connection with a stock, although intrusive rocks are known in the district. In such cases, the best ore guides are strata and district-wide faulting. Dikes and sills are also common and mineralization can locally prefer their contacts even though the igneous rocks are barren. Skam minerals are influenced by the chemical composition of the carbonate. Forsterite, brucite, tremolite, and talc are common in skams developed in dolomitic beds. Skams derived from calcic beds often contain wollastonite, calcite, stilbite, or idocrase. Diopside, however, is a common accompaniment of copper sulfide in skam regardless of the original composition of the carbonates. Tremolite and possibly other amphiboles and chlorite can occur significantly in the zinc-lead portion of skams. Gamets occur in magnetite, copper, and zinc-lead zones of skams, but are not as diagnostic as diopside for the copper zone or tremolite for the zinc-lead zone. A general desciption of skam-deposit mineralogy can be used to construct prospecting models of porphyry copper skams. An abstract of such a description follows.

Jan 1, 1991

By Doug Williams, Kent J. McGrew, Dr. Jack Murphy

For some time, selenate has eluded water treatment by conven­tional means such as precipitation and clarification. This has been due to the nearly universal solubility of all oxidized sele­nium species, the low levels required for surface discharge, and almost identical chemical behavior to all forms of oxidized sul­fur. The last characteristic makes selenate particularly difficult to deal with in acid mine waters where sulfate can easily be on the order of one gram per liter. Approaches such as ion exchange or reverse osmosis often tum into total demineraliza­tion schemes for the sake of removing a "trace" selenium species that may be present on the order of 108 sulfate/selenate. Reduction of selenate to selenite or elemental selenium by chemical means has been relatively unresearched. Some limit­ed success has been reported (Murphy, 1988) using ferrous hydroxide as a reducing agent; however, the reaction time as reported is too slow to be useful in a practical plant design. One significant difference between selenate and sulfate is that selenate has been discovered to be reducible in acid solution by elemental iron when catalyzed by soluble copper. Since the +4 or zero valence states of selenium are rather easy to deal with by coprecipitation with iron salts or alum, the elemental iron dis­solved in the process contributes to the overall process by pro­viding sludge upon raising the pH that can be separated by con­ventional clarification. Commercial production of selenium using copper catalyzed reduction of selenite to selenium metal via sulfur dioxide is well established, however, at the < 5 ppb requirements for surface discharge this reduction process equili­brates at levels far too high to be useful to low level selenate removal criteria. The reaction reported herein uses elemental iron for reduction of selenate with copper acting either as a cata­lyst or as a coprecipitation agent. This method, employed with conventional sludging, clarification and filtration can provide an economic method to achieve non detectable selenium (< 0.005 mg/I). Iron consumptions for the conditions tested have been on the order of 3 lbs/1,000 gallons treated. This represents as little as $0.06 or $2.00 per 1,000 gallons based on using a scrap source of iron or the purchase of electrolytic iron for the process.

Jan 1, 1996

By R. Allan Wallis

In the past mining engineers have tended to rely heavily on the advice of fan manufacturers in relation to fan equipment issues. A more adequate approach was advocated in a paper [ Wallis, 1965 ] submitted to the Eighth Commonwealth Mining and Metallurgical Congress held at Surfers Paradise, Australia during 1965. At that time Mount Isa Mine were in the process of installing 3 large 6096mm (20ft) diameter vertical axial flow surface fans of an advanced type [ Mathews et al, 1967 ]. The preliminary feasibility studies prior to preparing the detailed job specification for this project were extremely thorough with the result that it was possible to include detailed information and instructions in the document, ensuring the procurement of equipment that was satisfactory in all respects. Full advantage was taken of expert services provided by external organizations during the large coordinated multi-disciplinary exercise. My continuing activity and development in relation to the technology of axial flow fans is now at a stage where all known design and performance data are accessible through CAD programs [ Wallis and Kipp, 1987 ]. The extensive calculations that were necessary in 1983 can now be carried out in a mere fraction of the time, and with complete confidence. Model testing in order to validate the fan and duct design proposals is, in my view, no longer essential. The first of the computer programs enables a mine ventilation engineer to study a large number of alternative axial fan arrangements for comparison with the centrifugal alternative. By entering the volume flow rate, fan pressure and air density, he can then with ease, and rapidly, investigate the effect of various blading arrangements, downstream evasee area ratios, and hub ratios, on fan diameter and speed, with their related attainable fan efficiencies. This procedure had its origin back in the 60s when I was advising mining companies on new fan equipment. At that time such an investigation was quite lengthy and lacked the precision and completeness that is now available within the present programs. To obtain the major benefit from these outputs, it is most important not to be disconcerted by the three very important nondimensional parameters, namely, the tip flow coefficient (LAMt), the fan pressure coefficient (Kt or Kit), and the swirl coefficient (Es and/or Ep) as these are important when assessing the various design proposals. When seeking an understanding of the role and importance of each of these variables, ample help is provided in the user manual; the design recommendations are summarized in the help screens which are readily accessible within the design programs.

Jan 1, 1989

By Chris A. Fleming, Daan Seymore

The Golden Jubilee Mine in South Africa is the first mine in the Western World to introduce resin-in­pulp technology for the recovery of gold from a cyanide-leached slurry. Located in the Eastern Transvaal region of the country, the plant processes approximately 375 metric tons• of ore per day, of which over 90 per cent is mined in an open pit adjacent to the metaflurgical plant, while the remaining 5 to 10 per cent is trucl<ed in from two small high-grade deposits, located about 10 kilometers from the plant. The gold grade in the open pit is about 1 git, while the values m the two high-grade deposits range between 5 and 15 git. At the current treatment rate, the proven reserves m the three locations will last about another 10 years. Early testwork indicated that the ore was not well suited to conventional filtration processing or to heap leaching because of its high cfay content, and that carbon-m-pulp (CIP) would probably prove to be the most viable metallurgical route. Tcstwork to establish the feasibility of CIP for this application was carried out at Mintek in 1985. This worl<, which was based on batch-leaching and carbon-loading tests, indicated that CIP was technically feasible, but that both the rate of gold loading and the gold-loading capacity of the carbon were inferior to those obtained with Witwatersrand ores. The poor adsorption characteristics of the carbon were attributed to the abnormally high concentration of natural organic compounds (humates and fulvates) in the ore. Batch tests were therefore also carried out with strong-base resins, since resins are known (1] to be far less susceptible to organic fouling than is activated carbon. The results were very promising, and pointed to fast kinetics and a high loading capacity. (Fig. 1 ). Notwithstanding these findings, it was decided to recover gold with activated carbon at Golden Jubilee Mine because the CIP process was, by then, well established in South Africa and elsewhere in the world, whereas resin-in-pulp (RIP) was unproven technology. The r>lant was commissioned in September 1986 and, for 18 months, operated in a carbon-in-leach (CIL) configuration, i.e. with a total of . six leach tanks, the last four of which contained activated carbon. As could have been predicted from the laboratory results, the performance of the CIL plant was generally poor, low gold loadings on the carbon (less than 1500 git) and high losses of soluble gold (0.2 to 0.3 p.p.m.) bemg characteristic of the operation. Consequently, it

Jan 1, 1990

By Andrew J. Regis

The methods of evaluation of industrial minerals occurring on Federal lands have different meanings if the evaluations are done by a company rather than a government agency. For example, when the Bureau of Land Management (BLM) conducts an examination of mining claims, this is commonly referred to as a "validity examination," whereas it is an "economic evaluation" when performed by a company. Not only is there a difference in nomenclature in these evaluations, but there is a general lack of expertise in the Federal government on industrial minerals in general. A metallic mentality still prevails in the U.S. Forest Service (USFS) and the BLM. Because of this, many validity exams on industrial-mineral deposits commonly just skim the surface concerning economics and marketability. The BLM and USFS place a high amount of emphasis on past administrative case law pertaining to the validity of industrial minerals under the 1872 Mining Law and, rightly so, on marketability, which also is heavily addressed in case law. When the BLM considers marketability, only the marketability of a particular industrial mineral for only the primary use for which it was located is considered and any value-added markets cannot be included. The BLM defines marketability based only on the value of the mineral material in its in situ or raw state, rather than value-added through processing. Another difference in the evaluation of industrial minerals by government and industry is the question of by-products. When a company evaluates a mineral material it looks at all the markets. The BLM looks only at that market for that locatable mineral for which the claim was located. In other words, sales from non-locatable by-products cannot be used to support marketability or the prudent-man rule (i.e., oversize silica sand from a glass-sand claim being sold for construction sand, road base, fill, etc.). The question of reserves also can present conflicts. An industrial-mineral company will often try to identify all the reserves available for a possible future development. They must do this for financial backing and support from upper management. The BLM, however, will limit their validity examination only to those reserves that meet the prudent-man rule and marketability tests. The BLM will validate reserves sufficient to last 25-30 years, based on available market. The development of industrial minerals on Federal lands is a difficult process, and, if the 1872 Mining Law is changed, it could become not only more challenging but also more costly. The industry must become more tolerant of the mineral specialists in the BLM and the USFS. On the other hand, the government mineral examiners must become more aware of the importance of industrial minerals in everyday living, and the economic evaluation of these materials.

Jan 1, 1999

By A. S. Paschoa, A. W. Nóbrega

INTRODUCTION There are now over twenty years since the radiological characteristics of the brazilian regions of Araxá, Tapira and Barreiros, three locations adjacent to each other, in the state of Minas Gerais, Brazil, started being surveyed by investigators from the Instituto de Biofísica da Universidade Federal do Rio de Janeiro (IB/UFRJ), Pontifícia Universidade Católica do Rio de Janeiro (PUC/RJ), and New York University (NYU) (Roser and Cullen, 1958; Cullen et al, 1980). The importance of the Araxá apatite – Ca5,(P04)3(OH, F, Cl) - and pyrochlore - NaCaNB206F - for the production of large quantities of fertilizers and niobium was early recognized (Roser and Cullen, 1958). Interesting data have been gathered and published throughout the years on the contents of naturally occurring radionuclides in geologic materials, soils, grass, foods and waters of the Araxá region (Eisenbud, et al., 1964; Penna Franca, et al., 1965a, b; Roser et al., 1966; Penna Franca et al., 1970; Cullen, 1977; Penna Franca, 1977; Cullen and Paschoa, 1978; and Cullen et al., 1980). The radioactivity of the Araxá region is associated with mineral deposits of niobium rich pyrochlore and phosphate rich apatite. There are in this region mineral ores with 3 to 5% pyrochlore with 2 to 2.5% Th as Th02 and 50 to 150 ppm U308 in the matrix, while the apatite deposits contain up to 150 ppm U308 and a thorium concentration similar to that of the pyrochlore deposits (Paschoa and Palacios, 1981). As an indication of the high thorium content of the Araxá soils the 228Ra and 224Ra activity concentrations were reported to range from 10.6±0.2 to 62.4±0.7 pCi228Ra/g soil in 7 samples and 2.1±0.1 to 104±1 pCi224Ra/g soil in 19 samples (Cullen, et al., 1966). The uptake of radium isotopes by edible roots vegatables and fruits growing in the soils of the Araxá region can be illustrated by the data listed in Table I. The biological availability of natural radium isotopes in some segments of the Araxá soil allows a large variation in the 228Ra, 224Ra and 226Ra concentrations in vegetables and edible roots, as can be seen in Table I. This fact makes quite difficult a quantitative local assessment of the radiological implications of mining the Araxá mineral deposits of pyrochlore and apatite for production of niobium and phosphate fertilizers, respectively; since one cannot easily separate the naturally occurring from the technogically enhanced radionuclide contents of foods. The position of the city of Araxá inside the contour of the state of Minas Gerais appears in the upper part of Figure 1, which shows the outlined map of Brazil with the positions of the cities Brasilia and Rio de Janeiro also indicated. The lower part of Figure 1 is a representation of the Araxá region in an expanded scale, which indicates the locations of the pyrochlore and apatite deposits in relation to the city of Araxá, as well as the nearby hydrographic basins. The distance between the city of Araxá and the pyrochlore deposit is about 8 km, and between the pyrochlore and apatite deposits is 4 km. This paper deals tentatively with the radiological implications of the industrial operations taking place in the Araxá region for the exploration of the pyrochlore and apatite deposits. However, one must bear in mind, firstly, that the radiological implications of these industrial activities are by far too complex to be covered adequately by the limited amount of data to be presented in this paper, and secondly, that such implications cannot be considered of local character only. INDUSTRIAL OPERATIONS The commercial exploration of the Araxá deposits of pyrochlore and apatite started only few years ago, motivated by the increasing demand of niobium and phosphate fertilizers in Brazil and the world. As a consequence of the industrial operations in Araxá, a redistribution of the uranium, thorium, and radium originally present in the local deposits of pyrochlore and apatite started occurring in the seventies, with possible radiological implications for the Araxá region and its immediate surroundings, not to mention the destinations of the end products of such industrial operations. A literature review on the radioactivity associated with the extration industries of selected minerals was made by the USEPA (Bliss, 1978). The low level radioactive wastes of the industries for copper ore mining and rare metals processing have been object of particular attention (Fitzgerald, Jr., 1976; Eng, et al., 1979), but the short and long term implications of the radioactivity associated with the niobium industry were also subjects of concern (Knight and Makepeace, 1978). Recently, high 232Th and 226Ra concentrations in samples from the tin mining industry in West Malaysia were reported (Hu et al., 1981). A great deal of attention has been dedicated to the implications of the redistribution of radionuclides originally present in the mineral ores used by the phosphate fertilizer industry (Moore, 1967; Menzel, 1968; Spalding and Sackett, 1972; Eisenbud, 1973; Guimond and Windham, 1975; Guimond, 1976; Roessler,

Jan 1, 1981

By P. Mousset-Jones, G. Danko

Rock thermophysical properties, i.e. heat conductivity and thermal diffusivity, were obtained for reference values at the Waldo Test Mine for mine fire simulation purposes. An in situ measurement method was chosen since it could include the effect of rock fractures. The REKA method (Rapid Evaluation of k and alpha) was used because it can measure conductivity (k) and diffusivity (alpha) simultaneously within an eight-hour measurement period. A total of six measurements were taken in three different holes, and at two different depths from the collar of the hole. Each measurement provided an averaged conductivity and diffusivity for a volume of rock of approximately one cubic meter. The boreholes were driven into the upper and lower limestone, two at right angles to and one parallel to, the stratification of the rock. Significant representative conductivity and diffusivity values were obtained for the whole mine by averaging the six measurement results. The thermal properties for the band of shale in between the two limestones were not measured in situ, but only in the laboratory. Problems were encountered in the evaluation because of unexpected heat conduction on one side of the symmetrically built probe. A modification was made to the previously developed evaluation method together with further testing and correction, before the final results were obtained. As expected, the in situ and lab- oratory measured values of k and alpha compared favorably, since the in situ rock was dry and relatively unstressed.

Jan 1, 1989

By D. Kruse, M. Sanaei

"A three dimensional nonlinear finite element model was constructed to simulate and analyze the behavior of large diameter segmentally lined shafts when subjected to seismic waves. To reduce computation time, a less complex shell model was also constructed. Transient excitation was applied to the supported nodes of both models, at the base of the shaft, with a time-function representing the 1994 Northridge earthquake. The models are developed at the end of an original phased construction-stage analysis of the shaft. Displacements, forces and moments are monitored and compared during the analyses steps. During the initial 15 seconds of the earthquake, the top and bottom of the shaft show similar displacements. The maximum horizontal displacement within the shaft is approximately 3.5 inches in the solid model and the shell model results conform to this by a factor of 50%. Keywords: Segmentally Lined Shaft, Soil Structure Interaction, Seismic Analysis, Finite Element Modeling, Ground Modification INTRODUCTION TO SEGMENTALLY LINED SHAFTS Large diameter segmentally lined shafts (SLS) are underground systems, constructed sequentially using precast concrete segments to form a ring which provides both temporary earth support during excavation and permanent structural support. The segments are connected via alignment pins, bolts, packer material and other structural components that ensure the continuity of the SLS. In this analysis, the construction process uses a top-down sequence wherein each soil layer is excavated, damp-proofing is installed and concrete segments are assembled to form each ring. This process is repeated until design depths are achieved completing the shaft. It is known that cylindrical structures sustain lateral (earth) pressure mainly through the mechanism of hoop-stress. As Timoshenko’s ring theory goes, a cylinder shell structure is prone to buckling under external pressure [1]. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. However, in shafts with large diameter to wall thickness ratios, buckling could become a critical issue. In any given mode, as buckling occurs in a ring, some sections of the structure move inward while alternating sections protrude. Although the presence of the surrounding soil could mitigate the buckling by resisting the movement (Soil structure interaction) seismic loads can cause ground movements and lateral pressures, exceeding the capacity of the structure. It is therefore essential to design the load bearing capacities of the shaft to minimize the possibility of any catastrophic failure due to earthquakes. This study explores the structural response of the SLS when subjected to seismic loads."

Jan 1, 2016

By Dale W. Norris, John A. L. Campbell

INTRODUCTION Optimization, as measured by productivity gains, is being achieved in our nation&apos;s preparation plants principally by automation, economy of scale, and reducing maintenance. Increased tonnage per unit of investment, a1 so a measure of optimization, is being achieved by breaking with tradition and increasing plant utilization, while simultaneously improving on equipment re1iabi1ity. Improved qua1ity, another measure of optimization, is being attained through technical innovation. This review will concentrate on state-of-the- art unit operations and processes, and will not discuss emerging new technologies which are covered in detail in other presentations of this symposium. It is recognized that much of what will be discussed in this paper is not unique to the fine coal circuit, but is equally applicable to the entire preparation plant. However, the areas reviewed are the principal means being used today to optimize an existing preparation plant&apos;s fine coal circuit. Prior to designing and optimizing a fine coal cleaning circuit, the question that must first be answered is, "Do we even want a fine coal circuit? This is a much more complex question than is readily apparent, as most of you recognize. It can be argued either way. In the final analysis the "bottom line" will hold (Blackmore, 1982). If your sales contract a1 lows it, and the selling price can justify it, you most assuredly want to build a fine coal circuit into your preparation plant. In general today, most new preparation plants do have fine coal cleaning circuits. The purpose of fine coal cleaning has changed with time. Some of the early applications of fine coal cleaning were to prevent stream pollution rather than to prepare a product for market (Merrill a Pennington, 1962). During the 50&apos;s, 60&apos;s and into the 70&apos;s the principal thrust of fine coal cleaning was in metallurgical coal preparation. More recently, the emphasis of the 80&apos;s is on steam coal processing. There is no consensus on what is fine coal. Traditionally, fine coal would be anything below 1/4" in size. Because of the advances being made in intermediate coal cleaning processes, i.e. heavy media cyclones and jig cleaning, this discussion will define fine coal as -28 mesh (Aplan, 1987). Figure 1 is a plot of the size ranges of a large number of U.S. bituminous coals. In general the -28 mesh fraction of a bituminous coal will be between 7% and 18% of the ROM feed with reported ranges of 5% to 40% (Aplan, 1987). Consequently, traditional fine coal cleaning is general 1 y involved with a re1 actively mi nor portion of the coal feed. Every effort is taken both in terms of mining and preparation to keep it that way because of the high cost of cleaning fines. The move away from this posture, namely, the techniques to fine grind coal to liberate pyrite is probably the biggest challenge facing fine coal processing today.

Jan 1, 1988

By Surendra K. Mishra

The increasing volume of wastes being generated by industry is a legacy of the industrial revolution and subsequent industrial growth. Social and regulatory pressures have been mounting on industry to improve its waste management practices. In many industrial sectors, waste disposal has been the only method of waste management. Land farming, underground burial, deep wells and incineration are still practiced. Often, concentration and volume reduction of waste streams are also practiced to reduce the waste management costs. In the recent years, there has been emphasis on waste minimization. Since the 19th century, industry has practiced recycling of usable resources as a way of handling unwanted byproducts. The mining industry has recovered or extracted economic minerals from tailings for decades. For example, during the gold rush period of 1970s, extraction of gold from tailings dams became economically attractive. Similarly, when it was economical, coal and shale fractions have also been recovered from tailings and refuge materials for commercial uses. In the steel industry, with the development of new furnace technology, recycling of flue dust and scrap iron was practiced as early as in the 19th century. Before 1900, there was little incentive for the industry to reduce the waste volumes. Manufacturers, however, did see a rationale for adopting profit-increasing techniques. They made an effort to recover and recycle economic materials from waste sources. One of the pioneering examples of resource recovery is the coke making industry. As the industry was market driven, products recycled from coke batteries included ammonia for use in fertilizers, gas for power generation and heating, and tar for road construction, wood preservation and roofing. Tar had been avery troublesome waste byproduct. But it quickly became a valuable chemical raw material, providing the foundation for Germany&apos;s dominance of the world&apos;s dye and medicine markets before World War I. Similar trends evolved in the chemical industry. In the context of current environmental regulations and escalating mining and processing costs, recycling of re- [ ] sources is becoming economically more attractive. Solid and liquid wastes generated by industries contain a range of inorganic and organic contaminants. Among these contaminants, metals and hydrocarbons form major groups. Treatment of these wastes is essential to meet regulatory disposal requirements. In the recent years, based on the principles of chemical and mineral process engineering, processes have been developed to treat these industrial wastes. This article reviews some of the processes that have made impacts and have proven to be effective at commercial scales.

Jan 1, 1999

By Keith Kern, Joseph P. Matoney, Kenneth E. Harrison

INTRODUCTION "When there is an economic need for cleaning fine coal to low ash, the technical difficulties will be solved. The utilization of fines below 28 mesh will determine the degree to which beneficiation will be carried. Whenever these "fines" will be processed into smokeless fuels or used as new materials for the chemical industry or for hydrogenation, a higher degree of cleaning will be economically justified”.(l) This quote from the 1943 edition of Coal Preparation correctly anticipates the use of fines as "smokeless" fuel or as a future component of boiler fuel and a1 so as a raw material for the chemical industry or possible new uses such as for internal combustion engines. Fines utilization depends upon an economic need and possibly neglects to say an environmental need or a government funded development program as the prime mover for development. In any event, this conference is faced with the "need" to beneficiate fine coal and undoubtedly among the processes that will be discussed are the unit processes of future coal preparation facilities. HISTORY OF DEVELOPMENT It is interesting to look at where we have been, where we are now and where we possibly will be in the future. In order to put some limitations on this presentation, we will for the most part confine our remarks to this century and particularly developments since World War II. We also will limit our remarks to the preparation of bituminous coals in the United States, and for the most part, to wet processes. In the 1943 edition of Coal Preparation, clues to the processes being used to beneficiate coal are contained in the Chapter Titles. An extensive treatment of "Hand Picking" was contained in Chapter 8. Chapter 7 contained a description of methods for "Preparation at the Face". Chapter 18 dealt with "Slurries, Sludges, Slimes and Water Treatment" and defined this size of coal as being the size at which "Jigs and Chance Cones are usually dispensed with and other methods such as the hydrator, tables, and froth flotation are employed. Generally the limit is 1.7mm to 3.4mm. In the days before World War I1 the then modern bituminous coal preparation plant contained jigs or Chance Cones for the coarse material +6.35mm, concentrating tables, launders or some classifier type of coal washer for the fines (6.35 x 0.15mm), and froth flotation as the only method of cleaning minus 0.15mm coal which was used very sparingly.

Jan 1, 1988

By E. J. Jacques

A typical problem in ventilation networks with multiple fan systems is the possibility of them interacting. Multiple fan systems are no exceptions in complex tunnels, and may also be met in mines where underground fans are installed. When aiming at controlling a multiple fan system in a ventilation network, e.g. with a view to maintaining an acceptable air quality level, yet at minimum power consumption, transient flow conditions frequently occur. Although in most applications these transients are short compared to the time needed to achieve the planned actions on the ventilation, one should, however, keep in mind that it is important to avoid any bouncing effect between different (adjacent or distant) fan systems. Therefore a simulation of the unsteady-state flows could allow us to learn more about the propagation of transients within the network, and their possible secondary effects Among others, one question that often is raised, is to find out in which sequence and at what time schedule each of the fans in a network should e.g. be started up? Another typical problem, into which an unsteady-state simulation could provide some insight is the following: how should the facilities of variable pitch angle and/or changeable RPM of several fans operating in parallel be handled and combined in order to obtain a flow rate that changes gradually from zero to its maximum value i.e. the sum of the individual throughput flows of all the fans. The literature is not very abundant on the topic of simulating transient flows in networks. There is no doubt that numerical models have been developed (Pollak, Christensen, 1987), most of the time for particular applications (Wala, Kim, 1985), (Tanaskovic et al., 1984), (Schultz, Sockel, 1991), etc. The aim of this paper is to present a model that also simulates one-dimensional compressible flows in unsteady-state conditions with, however, the specific intent to handle networks with more than one fan. PROBLEM STATEMENT The mathematical model chosen to describe the unsteady flows in a ventilation network is based on the dynamic and continuity equations applied to each of its airways. The following basic assumptions are made : - the flow in the airway is considered to be one- dimensional, - - the flow is assumed to be fully turbulent, and hence the ATKINSON equation for calculating the friction losses will be applied. Whether this equation remains valid for transient state flows remains an open question. However, this may reasonably be assumed since the interesting flow frequencies are low. A discussion may be found in (Kämpf, 1987) ; - the airways are assumed to have a constant cross- sectional area along their length. If obviously this would not be the case, it is always possible to subdivide the concerned airway into sections for which the previous assumption holds. Applying the basic equations of mass and energy conservation, the flow in each branch may be described by the Euler equation for Newtonian flows.

Jan 1, 1995

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985

By James H. Nulty, Joseph S. Roti

INTRODUCTION During a recent panel discussion on the topic of millwater antiscalants, the question was posed: "What would you like to see in the future?" Answer: &apos;We need an antiscalant that: can be fed without a pump (no maintenance), functions on residual basis (no fault), can be tested for colorimetrically in sub-part-per- mi 11 ion concentrations (no guessing) and will recycle back to the mill from tailings (no cost).” Impossible? Based upon today&apos;s level of technology, such a product does not exist. However, a few of the qualifications listed above are certainly food for future thought. Meanwhile, progress is being made in upgrading three essential elements in this critical area of ore processing. They are: 1. Antiscalant reagent research and development. 2. On-line monitoring programs. 3. Reagent storage and feed systems. The objective of this paper is to out- line the current direction being taken in each of these areas and to present case histories as examples of how theory has been applied in field situations to better improve operations. LABORATORY SCREENING TESTS Recent technical papers have explained the various generic chemical raw materials which are available in the marketplace. While the merits of each chemical component are open to debate, the processes used by most major reagent suppliers to evaluate products in the laboratory are fairly standard. Common techniques incorporate both static and dynamic conditions in the search for the most cost effective product. Static Test Perhaps the most common test procedure used is based upon NACE Standard Test Method 03-74, which is "a laboratory screening test to determine the ability of scale inhibitors to prevent precipitation of calcium sulfate and calcium carbonate from solution." The objective of this test is to measure the change in calcium ion concentration in a container of saturated stock solution prepared from calcium chloride and sodium carbonate which is heated in a water bath. After 12 hours at constant temperature (160°), the mother liquor is pipetted into a beaker and a titrated for gm/l of unprecipitated calcium ion. A simultaneous test is performed on stock solution with antiscalant added. The results are then charted to determine the most effective antiscalant (with respect to preventing precipitation of calcite). It should be noted that this procedure examines only the ability of a chemical additive to retain calcite in a saturated solution where thermal stress is applied. This is commonly referred to as sequestration or stabilization. It has been documented that products which act in this manner (i.e., inorganic and organic phosphates) are good scale inhibitors. However, low molecular weight anionic polymers function in a much different manner by distorting calcite crystal size, shape and charge density, thus preventing scale formation. Because of this different mode of operation, static tests may not prove conclusive where polymers and sequestrants are being compared. The simplicity of this test makes it easily adaptable for field use, although modifications are often made.

Jan 1, 1986

By Robert W. Lawson

INTRODUCTION Prior to 1705, underground mining was limited to mineral deposits located above or a very small distance below the water table. The development of the steamdriven mining pump was motivated by the need to extract minerals from deposits considerably lower than the water table. Today, the majority of mine pumps are driven by electric motors, although some small utility pumps are driven by compressed air. Of the numerous types of pumps that might be applied to mine service, the two types used most frequently underground are the centrifugal and plunger pumps. Each of these types has its proper application. In most instances, plunger pumps are best for handling low water volumes against high heads, while centrifugal pumps effectively handle either low or high water volumes against low heads or high water volumes against high heads. This chapter describes pumps applied to underground mine service, where the mine service consists of mine drainage (removing mine water as it accumulates), mine dewatering (removing water from a flooded mine), and pumping for special applications such as hydraulic mining and hydraulic hoisting. CENTRIFUGAL AND PLUNGER PUMPS Modern mine pumps are classified as either centrifugal (kinetic) or plunger (positive-displacement) pumps. The following paragraphs describe each of these classifications. Centrifugal Pumps Centrifugal pumps may be grouped into various types, depending upon their various features: Number of Stages: In a single-stage pump, the total head is developed by one impeller, while a multi¬stage pump utilizes two or more impellers acting in one casing to develop the total head. Fig. I shows a cutaway view of a single-stage horizontal split-case double -section centrifugal pump. Fig. 2 shows a cutaway view of a six-stage medium-pressure split-case diffuser-type centrifugal pump. Type of Casing: A volute pump has a casing in the form of a spiral or volute. A circular-casing pump has a casing of constant cross section concentric with the impeller. A diffuser pump is equipped with a diffuser that converts velocity head to pressure head. Shaft Position: A horizontal pump normally has the shaft in a horizontal position, while a vertical pump normally has the shaft in a vertical position. Fig. 3 illustrates a vertical turbine-type slurry pump. Suction: A single-suction pump equips the first stage with a single-suction impeller, with fluid entering the impeller on only one side. A double-suction pump equips

Jan 1, 1982

By Stanislaw Wasilewski, Zdzislaw Krzystanek

The CMC-3 new generation system for continuous methane monitoring enables on-line measurement of methane concentration within the range of 0-100% CH4 with a great autonomy of operation. In principle the system has been worked out in the asspect of hazard detection in mines endangered with rock and gas outbursts. But after last crash in the Halemba colliery, according to the recommendation of the after-accident committee, the system was directed to this colliery for operational tests. The paper describes construction and functions of this system and gives some results of tests conducted at the Halemba colliery. The results point out the necessity of using monitoring equipment of continuous operation in mines of high dynamics of methane emission. INTRODUCTION Commonly used in Polish coal mining the methane monitoring systems of CTT/63/46 Up or CMM-20 and CMC-1 type are based on cyclic measurements with 4-minute repetition of measurements. This period has been stated sufficient from viewpoint of methane emission dynamics under normal exploatation. In these systems, automatic switching-off electrical power is performed by the surface station, i.e in case of detecting exceeded concentration value the station generates control pulse signal which actuates the switchng-off devices CRA and IZZO. Such a way of disconnection causes a considerable time delay, up to several minutes, in electric power break at hazardous areas. In the methane monitoring system with the new CMC-3 station, the different phylosophy of operation has been applied. Measurement of methane concentration is performed in a continnous way. In case of exceeding the alarm value, immediate control of the IZZO unit directly by methane monitor follows and consequently energy break without necessity of communicating with the surface station. Alarm values are set directly in methane monitor. The system ensures central powering of underground equipment from the surface, and in case of power failure the methane monitor equipped with battery operates autonomously for about 12 hours. Such an extention of the methane monitor funtionality has been achieved thanks to the use of internal microprocessor controller. The system with the CMC-3 station has been worked out in the aspect of methane hazard detection in mines exposed to gas outbursts. But after last gas explosion, according the desicion of the After-accident Commitee, the system was installed in the Halemba coliery where it underwent operational tests. Besides

Jan 1, 1993

By 000-000-604

HISTORIACAL INTRODUCTION Mineral processing has three principle branches, to quote Taggart, "Ore Dressing, which comprises the methods of separation of solids in inorganic crude by means which do not affect substantial chemical change; Extractive Metallurgy, which utilizes chemical reactions for separations of constituents from solids in inorganic crude; and, Fuel Technology, which employs both physical and chemical methods for separating and rearrangement of liquid gaseous and solid components in crude oil and natural gas, tar sands, shale oil, or coal." The scope of this handbook covers the first two classifications, that is, "ore dressing" and "extractive metallurgy," which have been combined in one term: "mineral processing." For a brief history of the development of mineral processing, one could well refer to the Introduction, Sec. I of the Handbook of Mineral Dressing by Taggart, Froth Flotation, Principles of Mineral Dressing by Gaudin, and the original Richard&apos;s Ore Dressing, volume No. 1, first published in 1903-1905. In these references and the references given in them a coverage of the history of "ore dressing" can be found and studied at the reader&apos;s leisure. For the history of extractive metallurgy as well as ore dressing, the bibliography in General References, taken from a History of Ex¬tractive Metallurgy by F. Habashi, will give a good background for those who are interested in more detail on the history of metallurgy in general. Mineral processing covers a very wide field as is illustrated by the topics discussed in Part II of this handbook and dates back to the early history of man which started with the production and use of native minerals such as gold, silver, copper, mercury, and meteoric iron which were washed or picked from deposits on the surface of the earth and worked because of their malleability. Later, melting was discovered and then it was possible to cast objects of these metals, excluding mercury. The discovery of a method for reducing the metal¬lic oxide probably was developed from melting fragments of oxides or roasted sulfides with charcoal, so that the native metal could be produced in simple blast furnaces such as are used today in rural parts of Spain, China, and elsewhere. Eventually, it was learned that iron could be readily worked when hot, which resulted in its replacing bronze for tools, weapons, and cutlery. Carbon dating and correlation with the Brittle Cone pine has

Jan 1, 1985

By Frank C. Di Luzio

REMARKS BY FRANK C. DI LUZIO, ASSISTANT SECRETARY OF THE INTERIOR FOR WATER POLLUTION CONTROL, BEFORE THE ANNUAL MEETING OF THE AMERICAN INSTITUTE OF MINING ENGINEERS, NEW YORK CITY, FEBRUARY 25-29, 1968 POLLUTION PROBLEMS AFTER MUNICIPAL-INDUSTRIAL WASTE CONTROL I am happy to have this opportunity to discuss pollution problems related to the mining industry and the role of mining engineers in protecting our environment. Technological Power and Pollution of the Environment The increasing power of technology to destroy and disrupt the natural environment and the ecological systems upon which life depends has reduced man&apos;s margin for error in the use of this power. We must act, therefore, to deter and prevent the occurrence of future ecological disasters such as that caused on the British and French coasts by the sunken oil tanker, the TORREY CANYON, the Clinch River fish kill which occurred when a dam broke and released coal ash from a power plant operation, or that which threatened on the Clark Fork River in Montana when a strike at the Anaconda Copper Company threatened to shut down pollution control activities, thereby endangering fish and plant life on the Clark Fork River with copper waste. In the past, pollution of the environment has tended to be slow. But now, the increased power of technology to damage nature, the loss of in¬sulating space and the compression of time--all reduce our margin for error and the cushion which space and time once provided for our mistakes.

Jan 1, 1968

By Michael J. Virnig, Keith E. Weerts

The development of heap leach technology for the treatment of low grade gold and silver ores has led to a boom in gold production in the Western United States in the last 15 years. The heap leaching process consists of stacking the mined ore on a specially prepared leach pad followed by leaching with dilute alkaline cyanide solution. Depending on the nature of the ore, it may require crushing and/or agglomeration prior to stacking on the leach pad. As the dilute alkaline cyanide solution migrates down through the stacked ore, the precious metal values along with a portion of the base metal values present in the ore are dissolved to give a pregnant leach solution which is collected at the base of the stacked ore. The precious metal values are then recovered by zinc precipitation or by adsorption on activated carbon. Once all of the economic metal values have been leached from the ore, the spent heap leach pad, the leached materials, and associated process solutions must be decomissioned. Decommissioning requires that the spent heap leach pad along with the leached materials and process solution be treated to reduce the concentration of the residual cyanide, base metal cyanide complexes, and other anionic metal species to levels where they no longer represent a long tenn liability for the environment and the operator. The levels to which these components must be reduced is dependent upon the applicable water quality standards as determined by the responsible federal, state, and local agencies. As environmental awareness has grown, these standards have become increasingly stringent. A number of treatment options have been developed for the de-toxification of the process residues. These include natural degradation which incorporates bio-degradation, fresh water rinsing, alkaline chlorination, hydrogen peroxide, and sulfur dioxide/air. Each of these options has been reviewed with regard to relative effectiveness, generation of hazardous by­products, reagent handling considerations, relative costs, and time requirements by Denton, Iverson, and Gosling I. As an outgrowth of the program to develop Henkel's guanidine based gold extractants, COGNIS, Inc., the environmental ann of Henkel, has developed the CyanoMet R process for the extraction and concentration of the various cyanide and anionic metal species from the dilute aqueous alkaline solutions generated during the process of detoxifying spent heap leach pads. This paper describes the CyanoMet R process, its application to three different feed solutions, and treatment of the concentrate generated by the process.

Jan 1, 1993

By Douglas R. Shaw

The results are discussed herein of laboratory and pilot scale research which has demonstrated some exciting prospects for the exploitation of refractory gold resources by heap leaching. The research examined practical and cost effective methods of chemical; i.e., non-biological, oxidation pretreatment of refrac­ tory old ores to enable successful conventional cyanide heap leachmg. The work has focused on regenerable chemicals, in order to minimize process consumable costs. A nitric acid method has emerged which offers rapid oxidation rates (eg, 0.5 to 6 hours) on ore samples crushed typically to% to ¾-inch. Gold recoveries in simulated heap leaching tests, after nitric acid oxidation of crushed ores, were as high as approximately 80 to over 90%, in contrast, typically, to negligible gold solu­bilities without oxidation. Nitric acid oxidation was effective when applied to several sulfide-bearing refractory gold ores which required either partial or essentially complete sulfide sul­fur conversion for high gold solubilities in cyanide. Ores rich in organic preg-robbing matter also were treated successfully, as were ores which contain significant quantities of acid-consum­ing constituents. Base metals also were recovered with nitric acid oxidation from some of the ores which contain these ele­ments. The work related oxidation and solution diffusion behav­iors and the important physical, textural, and mineralogical characteristics of the different ore types. Conceptual-level feasi­bility studies have defined the principal capital and operating cost components of the nitric acid method, sufficient to allow reliable comparisons with other oxidative technologies.

Jan 1, 1996