Search Documents

By Tácio Ferreira, Liz Diaz

Capstone Copper’s Pinto Valley Mine faced challenges in recovering rock and ore on final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall stability. The operation had been using the same drill-and-blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at 345 kt/a (380,000 stpy) generated from an average of 60 final wall blasts performed annually. The engineering team from Capstone and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. This article presents how data were collected and design standards reviewed, and the opportunities that were found to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71 percent on the mine’s highwalls.

Aug 1, 2025

By R. Krog, M. Valente, R. Ochsner, W. Marchewka, R. Jensen, R. K. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine for analysis and display on the surface. The U.S. National Institute for Occupational Safety and Health (NIOSH), in collaboration with Signal Peak Energy (SPE), LLC, Bull Mountains No. 1 Mine, operated a TBS during mining of two bleederless, longwall panels. This paper describes the gas analysis data and its interpretation. As verified by the TBS, coal at the SPE mine tends to oxidize slowly. It was known that a reservoir of low-oxygen concentration atmosphere developed about 610 m (2,000 ft) behind the longwall face. A bleederless ventilation system facilitates formation of an inert atmosphere in this longwall gob and decreases the likelihood of spontaneous combustion. Connections of the mine atmosphere to the surface through subsidence cracks could allow airflow into the longwall gob, revive coal oxidation and increase spontaneous combustion risk. The atmospheric composition of the sealed areas was homogeneous, except in the immediate vicinity of suspected ingassing points. The TBS verified that gases within the partially sealed, bleederless longwall gob expanded into the longwall tailgate area when barometric pressure decreased. The concentration of carbon dioxide in the back return airflow at the longwall tailgate was observed to increase by a factor of three and possibly up to 10 times the typical background concentration of 0.5 to 1.0%, depending on the size of the longwall gob and the magnitude of barometric pressure decrease. TBS have the inherent disadvantage of slow response time due to travel time of the gas samples and sequential gas analyses. A TBS or similar continuous monitoring system could be beneficial in detecting and providing warning of potentially hazardous gas concentrations, if the slow response time of the system is always understood.

Jan 1, 2013

By José Mujica, Mónica Campos, María Fe Campos

The extraction and processing of metals and other minerals have played an important role in economic, political and social development worldwide, from the early stages of prehistory to the present day (Gosner, 2020). Mining has been a fundamental part of human civilization, providing the raw materials necessary for technological, infrastructure and industrial advances. As society progresses, the importance of mining continues to grow, supporting the development of everything from the smallest electronic devices to the tallest skyscrapers (Escamilla, 2024). The economy of a nation is connected to its extractive industries (Moreira and McMahon, 2014), which have seen dramatic growth in recent years (Pietrobelli et al., 2018). In a context of increasing demand for natural resources, driven by the development of emerging technologies, the expansion of infrastructure and the foundation of engineering achievements for the coming decades (Minerals Education Coalition, 2024), mining should focus efforts on global development, requiring a comprehensive approach to sustainability that addresses the planet’s needs and protects the well-being, primarily, of the communities and environments where mining operations take place (Figari, 2024). In these areas, diversity and inclusion should be promoted, thus fostering equitable and sustainable development. The sustainable development goals (SDGs), also known as the global goals, could serve as a key framework for fostering a strong social management culture in mining. The SDGs were adopted by the United Nations (UN) in 2015 as a universal call to end poverty, protect the planet, and ensure that all people enjoy peace and prosperity by 2030 (United Nations Development Programme, n.d.). Companies have compelling reasons to align their actions with the SDGs, as their long-term success depends on healthy communities. This is a major challenge that requires collaborative efforts (Singh and Rahman, 2021). As Fraser (2021) mentions, achieving more sustainable outcomes may involve mining companies and communities working together collaboratively. This article proposes an innovative approach: Inclusive mining for sustainable development, which aims not only to maximize economic profitability but also to promote social and environmental well-being by integrating the UN’s SDGs, primar)ily focused on diversity and inclusion. This can be achieved through the implementation of a key value-added initiative for mining companies: the creation and operation of a corporate volunteering program aimed at developing and executing inclusive practices to promote gender equality, the inclusion of local communities and indigenous peoples, and accessibility for people with disabilities. This proposal will educate employees and stakeholders about sustainability and promote concrete actions through corporate volunteering to strengthen the mining company’s commitment to community development, improve social relations and advance toward achieving the UN’s SDGs, establishing the company as a global change agent.

Nov 1, 2025

By Z. Sample

"INTRODUCTION This past year commodity prices continued their dip with increased volatility causing market values to slide another 16% putting increased pressure on even the largest companies to improve their free cash flow.[1] Without a recovery in commodity prices in sight, companies must find a sustainable method to improve returns in the current economic climate. In an effort to improve plant sustainability, the mineral processing industry is investing in advanced automation technologies and innovative processing methods that are both more reliable and more efficient than ever before. One such breakthrough technology is Heap Leaching (HL). This method of extraction has certain advantages over traditional metallurgical methods making previously unsustainable operations economically feasible. While HL is already seeing use in the gold and copper industries among others, recent developments may allow for the use of HL to process primary sulfide ores which make up about 80% of today’s ores.[2] For this reason, this emerging technology is poised for exciting growth. Unfortunately, as with any process change, the implementation of HL projects requires significant training on both the control system as well as the underlying process, and further, due to the complex nature of the HL process, this can be a particularly difficult task. DEMOGRAPHIC TIME BOMB Even before the implementation of these new technologies, the availability of the skilled workforce has already become a significant problem for the mining and mineral processing industries. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years.[3] This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, research suggests that up to 50% of skilled mining and mineral process professionals are expected to retire in the next 5 years, leaving with their irreplaceable knowledge and experience.[4] While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences. In addition to a rapidly aging workforce and an inexperienced labor pool, a study done by the Oil and Gas Journal showed that it takes about 7 years, on average, for new workers to achieve a level of competency that permits them to assess risks and appropriately make decisions.[5] Not only is this figure is in direct conflict with the typical tenure of 5 years in one position meaning that the thinly spread skilled labor will be required to become senior staff before they are able to achieve competency in their current role, this also means that these millennials are not given the opportunity to become competent in their role before the retirement of the more experienced workforce."

Jan 1, 2016

By J. H. Rowland, R. A. Thomas, III, C. D. Litton

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners.

Jan 1, 2016

By DEVY DYSON, Brian Hart, JOHN LANGHANS, Stamen Dimov, STEVE YOPPS

A recent Nevada Gold Mines research program focused on the pressure oxidation (POx) pretreatment of a Carlin-type double refractory ore from the Turquoise Ridge Mine. The research team found that both arsenian pyrite and carbonaceous matter were highly oxidized within an hour at 300 °C using a bench-top autoclave reactor and that the gold recovery from the residues after cyanide/carbon-in-leach (CIL) approached the technical limit set by the amount of gold encapsulated by silicate minerals. Although the 60-min pretreatment at 300 °C yields robust performance when treating a whole ore, copper additives can catalyze the oxidation rate of carbonaceous matter and reduce the residence time needed at elevated temperatures. Certain gangue minerals are susceptible to dissolution in acidic solutions at 300 °C, and this may cause poor gold recovery. This recovery challenge is mitigated by keeping free acid in the discharge solution below a key threshold.

Nov 1, 2022

By A. J. S. Spearing, B. Forbes, T. Kostecki, A. Hyett

Improving upon the past understanding of the interaction between installed rock bolts, the immediate roof and sidewalls is vital for the implementation of sound support system design, as this has a direct impact on rock-related safety. This is the primary goal in rock-bolt-related research. The earliest research in this field concentrated on limited laboratory and in situ measurements accompanied by theoretical analyses, based on the Kirsch equations. This represented the initial insight into understanding relative ground movements and their impact on primary support. However, these studies were far from complete. More recently, major technological advances in computing power within the mining industry has changed the scope from theoretical analysis to computer simulation. Even with these advancements our understanding of rock bolts in situ and in the laboratory has not progressed, particularly concerning bending and shear. To measure the behavior of rock bolts, the widely accepted practice is to populate the bolts with an array of strain gauges. Historically, resistive foil strain gauges or long displacement sensors have been used. Additionally, all instrumented rock bolts have used only two diametrically opposed slots. Rock bolts instrumented with these methods have significant shortcomings, one of which is the inability to capture shear and bending. The shearing and bending of rock bolts are particularly common in tabular soft rock mining, such as coal mining. This paper discusses the use of three slotted rock bolts, cut diametrically 120º apart, and two new optical fiber technologies populated along the entire rock-bolt length.

Jan 1, 2015

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By Norman A. Nadel

Those of us who have directed our efforts toward the construction of tunnels have long maintained that tunnel construction is more closely an art than it is a science. We have spent time underground with hard-bitten, tobacco chewing shift bosses and superintendents who have made seat-of-the-pants decisions at the face which have been based upon their long experience underground coupled with uncanny intuition. The courage and skill of these men in the performance of their art is legendary. Without question, they have constituted the backbone of the tunnel construction industry. But just as John Henry, the steel driving man, despite his stout heart and dedication to his task, was supplanted by the steam drill, I fear that our tunnel stiff, at least as we have known him, will become an endangered if not extinct species. The reason for this is clearly that tunnel construction is slowly but inexorably making the transition from being an art into being a science, and more and more its performance is requiring the services of scientists as opposed to artists. The tunneling art has been undergoing change for many years, and yet until recently the changes have not been basic. We have improved the way we do the same old things. For example, John Henry would be flabbergasted if he saw the rock drills we use today. He would not have engaged in the legendary drilling contest with one of our modern drills, He would have simply conceded defeat.

Jan 1, 1970

By V. Voller

A relatively simple model of grinding which incorporates both the Bond grindability equations and the population balance equations has been extended to form a comprehensive simulation package that can describe most kinds of conventional grinding circuits. The package has two programs, with the first consisting of an input program which helps the user to specify the prescribed circuit, while the second program performs the actual simulation. The package serves two main purposes - i) as a check on mill design, with the output providing not only predictions for the product passing size but also of the full product size distribution, and ii) as a means to assess the likely effects on the product size distribution of operating under different sets of conditions.

Jan 1, 1981

By James L. Patton

Automation of mining increases the productivity of labor, thereby reducing the unit cost of labor. Such cost constitutes the largest portion of the direct or variable costs of producing coal. Therefore, any increase in productivity directly reduces variable cost. The large investment in mechanical equipment carries with it the burden of increased fixed charges. As the proportion of fixed cost to the total cost increases, the effects on the cost of production changes are amplified. Therefore, equipment must be fully utilized at all times. Averaged fixed costs rise with any decline in production. Such a situation forces coal companies to seek every means of main¬taining full production. Figure I will reflect the story on the relationship of production to cost.

Jan 1, 1962

By Clay Haynes, Tim Pearia, Robert Robinson, Judy Cochran

A 1.89 km-long, 4.5 m-I.D. tunnel was successfully constructed through saturated hard clay, and highly abrasive dense sand and gravel, with groundwater heads ranging from 10 to 20 m. In order to address these conditions, a Lovat earth pressure balance TBM was used, with soil conditioning by foam, water and various polymers. Support was provided by a single-pass segmented concrete lining. Groundwater inflows of 400to 1,600 lpm at times created challenges for changing cutting tools. Surface settlements were generally less than measurement thresholds, except under very low cover at startup. This project provides a pivotal case study of the successful application of EPBM technology in saturated, abrasive glacial soils and the successful application of soil conditioners.

Jan 1, 2003

By P. Malozemoff

Discussion by P. Malozemoff I have no objection to using mathematics in the value appraisal of properties. The factor that is not emphasized in the paper is that very few important properties have a lifetime that reflects the initial ore reserves of the property divided by the rate of production adopted. In the majority of cases, major properties mine out several times the initial reserves. How much more will be mined out is not known, and only exceptionally gifted geologists can predict that additional reserves will be found. There is the further factor of metals price, which, over the long term, is not predictable. Another factor vitiating making calculations on initially established ore reserves is the speculative nature of exploration success. In my judgment, the life of a property, in addition to an established ore reserve, should include ample time for exploration to find additional reserves. The likelihood of additional reserves is based on the geological promise of the general area where the mine is established. This is especially important because of various risk factors associated with small orebodies, the economic life of which is about five to seven years. In underground mines, it is not economic to develop reserves beyond a certain depth, so the life of initially established reserves must be limited. In these cases, it is especially important to have a good geological understanding of the orebody and its continuity. To accommodate these concepts and present proof of economic soundness for a mining enterprise, a mathematical analysis should yield a life long enough to allow exploration and the development of additional reserves that would ensure a longer mine life and a more profitable result.

Jan 1, 1994

By Douglas J. Piper

On reflection of certain overall circumstances which have pervaded the gold mining industry, it appears useful to point out some specifics which the writer hopes will improve the potential for success in the application of hydraulic dredges to gold mining activity. I will, prior to entering into that discussion, comment briefly on rule of thumb for the application of the three types of equipment. The three are bucket line, bucket wheel and drag line dredges. From a standpoint of high volume movement over a short distance, between 50 and 300 feet, the drag line dredge is historically the most cost effective type of machine to be utilized if bulk excavation is the single driving consideration. It is typical for this sort of equipment to operate in the 10 to 30 cents per cubic yard range, however, cost of operation is not the sole consideration. Typically the drag line mixes and remixes the material which it excavates. In the event that gold recovery is the object of the exercise, a strong potential for loss of the valued mineral exists. Additionally, drag lines do a poor job of bottom cleaning, particularly if there is a ridged or creviced bottom which must be cleaned and in some cases partially removed to assure recovery of the highest percent of valuable ore. The bucket line dredge has, until recently, been considered an extremely cost effective device. However, the high cost of manufacture of this type of equipment has mitigated against its use in the majority of

Jan 1, 1992

By Broderick E. Davis

Each year, about 45 Mt (50 million st) of flotation tailings are discarded in Florida phosphate operations. These tailings only contain about 4% of the phosphate in the ore. However, more than half of the phosphate in the tailings is concentrated in the +600 µm (+28 mesh) size fraction at grades of up to 20% P205. Many phosphate producers have attempted to solve this problem by floating the +425 µm (+35 mesh) flotation feed separately. However, phosphate recoveries in these circuits are typically only 60%. For seven sampled phosphate operations, the phosphate content of the +600 µm (+28 mesh) fatty acid tailings ranged from 15% to 25% P205. In every case, the +600 µm (+28 mesh) fatty acid tailings was higher in grade than the overall flotation feed. Attempts to efficiently recover this coarse phosphate have apparently been unsuccessful at these seven phosphate operations. Recovery of this coarse phosphate would provide an additional 900 kt to 2.5 Mt (I to 2.7 million st) of phosphate annually and add an additional year to the reserves of these important deposits. A typical central Florida phosphate matrix is composed of three different mixtures of minerals. The +1.18 mm (+ 16 mesh) portion is chiefly phosphate pebbles and is beneficiated by sizing. The -106 µm (-150 mesh) portion contains virtually all of the clay minerals and is discarded in the hydrocyclone overflow. The -l mm +106 µm (-16 +150 mesh) material is a mixture of quartz and phosphate minerals.

Jan 1, 1993

By William Tattersall

On behalf of my agency, the Mine Safety and Health Administration, I would like to add my appreciation that all of you could be here today. Previous dust symposia over the years have proved the value of close cooperation among universities, government agencies, and professional societies in advancing knowledge of dust research and development in the interest of miners and the industry. I'll just comment briefly on MSHA's part of the overall effort by all parties to control miners' exposure to respirable coal dust and other airborne dusts. As you know, our agency's congressional mandate is to do what is necessary to assure that miners will have safe and healthful workplaces. In the area of coal mine health, this has meant joining with the mining community in a continuous campaign to keep respirable dust and quartz levels below applicable standards to prevent or reduce disabling coal workers' pneumoconiosis and silicosis arising from excessive exposure to respirable quartz. Currently, our agency is processing about 120,000 coal dust samples taken by MSHA and company people during the year and about 8,000 samples taken from metal and nonmetal mining operations. Our dust program, like other MSHA programs, has benefited from increased computerization of records. The attack on CWP has had the highest priority of government and industry. The goal has been to sharply reduce social costs of suffering victims and their families as well as the associated future payments under the black lung benefits program. During the 1989 fiscal year, about 104,000 former miners received about one and a half billion dollars in benefits. Since the program began, nearly 25 billion dollars have been paid out. Much progress has been made in lowering dust levels in coal mines since the standard of two milligrams per meter of air was established in 1972. Before that time, there was a 4-to-10-percent probability of a miner developing coal workers' pneumoconiosis at typical pre-1972 exposure levels. However, under the maximum respirable dust levels allowed today, this probability has been reduced to about 1 percent. Since average dust levels are lower today, we can expect fewer miners to develop CWP in the future. Out goal continues to be elimination of both coal workers' pneumoconiosis and silicosis in both coal and nonmetal mining. In 1985, MSHA revised its coal mine quartz policy to allow mine operators to submit dust samples used in setting the quartz standard. Previously, only single MSHA samples were used. Even though less than half of the mine operators have taken advantage of this change, it has provided a larger population of samples for analysis then before. Also the policy allows operations that are on a reduced quartz standard to have the standard reviewed every six months. In underground coal mining, the job of roof bolter typically has higher than normal exposures to quartz. About 45 percent of respirable dust samples from roof bolting operations contain more than 5 percent quartz and therefore are put on a reduced quartz standard. One objective of the policy revision was to improve miners' health by follow-up monitoring, and this is being done with roof bolting jobs. MSHA studies of surface coal mining operations have provided data showing that bulldozer operators and highwall rotary drill operators often have high exposure to quartz dust, and our agency is directing enforcement efforts to reducing this hazard. One of the most important responsibilities of MSHA's metal and nonmetal mine health division is the respirable dust sampling program. In the last few years, nearly 3 out of 10 samples have

Jan 1, 1991

By W. J. Fotheringham

This paper deals with the mining techniques employed at Canada Tungsten's northern Canadian operations, particularly with respect to their effect on productivity, safety, and stability of relatively large underground openings. The ore body was originally mined commencing in 1974 using conventional pneumatic jumbos in a topslice and horizontal benching room and pillar layout. Pillar stability became an increasing problem as mining progressed, leading to a re-examination and ultimately a conversion of mining method. Rock mechanics considerations and the effect of extraction rate on ground control costs and conditions are analyzed. Other areas discussed concern the results acheived through the use of large diameter I.T.H. drills, radio remote controlled L.H.D. units, and a unique system of hydraulic backfill placement.

Jan 1, 1985

By A. M. Johnson, D. H. Carlson, D. L. Johnson, S. T. Bagley

A biologically assisted ferric iron leaching system was evaluated for in situ recovery of three copper sulfide oresfrorm northern Michigan. Laboratory scale bacterially assisted ferric sulfate leaching tests were run on the three ores. A T. ferrooxidans strain was found that could be adapted to copper in solutions at concentrations as high as 20 g/L. Column leaching of 4.5 to 2 mm (-4 +I0 mesh) material yielded extractions of 80-90% copper from one ore and 70 and 60% from the other ores. The highest copper extractions were from the Mount Bohemia ore deposits located in the Keweenaw Peninsula, which have fracture controlled chalcocite mineralization. The Bohemia ores are apparently well-suited for in situ solution mining.

Jan 1, 1987

By Peter J. Szabo

The mining executive works in a cyclical industry. His employment is subject to the vagaries of the marketplace. Boom and bust has always been the industry's story. "Big oil" failed in its mining effort. This left emotional and financial scars on many mining families. One must remember that mining executives always play a high-stakes game. Given the cyclical nature of the mining industry, mining executives need to take care of their own financial security. The mining executive that does not plan for his financial security in this cyclical business is playing Russian Roulette with his future. Take a look at those people who have reached their later years with the mining industry. One usually finds three categories of people. Those few in the first group have been fortunate enough to have worked for one company. They have survived the winnowing process of cyclicality, political problems, and takeovers. They have reached normal retirement age. For them, the retirement years are usually comfortable. People in the second group have worked for those same mining companies. But these people have been forced out by early retirement. Or they have been laid off for cyclical, takeover, or political reasons. The third group includes those who have held many positions in the mining industry. Probably not until their later years are they fully vested, if at all, in a pension program. The first small group, then, is the exception. The others, unless they have taken care of their financial security, are doomed to later years of financial problems, stress, and unhappiness. Too late in life, many realize the harsh realities of failure to plan and implement a personal financial program. Mining executives go to some of the world's leading mining schools, to learn how to make money. The curriculum is technically strong. Most mining graduates are familiar with the intricacies of discounted cash flow, present value, and the Hoskold formula. But few of these same mining schools require courses on personal financial planning. Such courses could give mining students a realistic foundation and the mechanisms with which to cope with their cyclical profession. An executive has only three sources of money. He can make money at work. He can put his money to work. Or he can get money from charities, such as government programs. Of these three sources of money, money at work has the best chance of providing financial security in later years. The mining executive must think of the day when he will be too old to work and contribute to the market place. At this point, the quantity and quality of his investments will determine whether his later years will be secure. Along with the Mining Engineering Handbook, two key books should be included in the mining executive's library. These are Venita Van Caspel's The Power of Money Dynamics and Benjamin J. Stein's Financial Passages. These books contain the basic concepts of personal financial planning so critical to an individual's financial survival. Venita points out the simple formula that is the key to financial independence: Time + Money + American Free Enterprise (Rate of Return) = Opportunity to Become Financially Independent Chart 1 shows that this is not a trite formula. The chart shows the dramatic effects of compounding over time. The chart also shows at various yields what a $2000 a year Individual Retirement Account (IRA) contribution will accumulate. Chart 1 (from Money magazine) is based on the future value of an ordinary annuity. It shows that the key to amassing a small fortune by the time a person reaches his 50s is starting to save methodically in his 20s. This, coupled with the highest yields consistent with safety of principal will ensure financial security. There are significant effects from compounding money over time. Every year the decision is put off to save for later years will cost a person dearly by the time he reaches his 50s. For example, consider the decision to put off for one year a $2000 IRA investment at a 12% return. Starting it at age 31 instead of 30 will cost the executive almost $100,000 by age 65. What if the executive waits until age 35 to get started with his $2000 a year investment? He will then lose nearly $400,000 by age 65. Stated another way, the executive costs himself this $400,000 simply because he did not invest $167 a month for five years. $167 a month - that's less than an inexpensive second car payment. This $400,000 pool of money could provide the executive a $40,000 a year income at age 65, assuming a 10% return on invest-

Jan 11, 1985

By A. A. Mular

Examining a typical curriculum for mineral process engineers shows that traditional subjects remain important, namely, engineering, earth and basic sciences, mathematics and mineral proc¬essing technology. However, Table I shows additional subjects that may be woven into a modern curriculum, because of micro- and macro-engineering advances over the years. The ways to incorporate these subjects into the curriculum will vary from school to school. Such changes are in response to evolutionary technological and political needs as determined by society and business. Beginning with the 1950s, engineering empiricism was strengthened through micro-engineering, where fundamentals and mechanism serve as foundations. Scientific apparatus unique to the basic sciences (Zeta meter, FTIR spectroscope) was adapted to test new hypotheses. Coincidentally, as computers became more available, complex differential

Jan 1, 1992