Search Documents

Planning the primary development of a mineral deposit usually is done only once during the life of a mine. As a consequence, not optimizing the primary development of a mineral deposit can cause disadvantages over the whole life of a mine and can lead to higher costs. As a contribution to an improved primary development design procedure beyond the already existing work a study of the identification and quantification of the influence of parameters on primary development based on operational data from working mining operations has been completed. Based upon such a quantification of the influence of parameters a sequenced decision model was developed, that enables to develop an initial concept for the design of the accesses from the surface based upon a few critical parameters. Such a model will not replace detailed planning work within a feasibility study, but it is intended to reduce the amount of planning efforts at an early project stage through providing information what are most likely economic solutions, based on simple rules.

Jan 1, 1997

By L. D. Boughton

Solution mining projects are conducted through one or more boreholes which penetrate en ore body. Proper drilling, completion and maintenance of the boreholes, therefore, is essential to the success of any solution mining operation. Wells drilled for solution mining encounter problems quite similar to problems encountered by the petroleum industry in drilling, completing and maintaining wells for the production of oil, gas or water. Many of the services developed and much of the experience gained by the petroleum industry is applicable to solution mining wells. As in the petroleum industry, each individual wellbore and ore body in a solution mining project provides its own problems. These vary greatly from well to well, and it is not possible to set down data or outline programs that will apply to all wells. Instead, the design of the drilling, completion, production and maintenance programs should be worked out for each individual well. The purpose of this paper, then, is to generally describe materials, equipment and techniques available for these programs and to discuss the purpose and sequence of their use.

Jan 1, 1971

By Mario E. Rossi

Often geometallurgical models are prepared at various project stages from very few data and are assumed to be representative of very large tonnages. These may include recovery models; crushing and grinding parameters and models; models of concentrate grades; models of acid consumption; etc. These models commonly do not carry a measure of uncertainty or variability, and are taken at face value at the time of design and planning. This paper proposes a proactive approach to modelling variability, providing uncertainty estimates and thus allowing for risk analysis and mitigation of geometallurgical models. The variability model is built up by understanding the limitations of the pillars of a geometallurgical model: data uncertainty; geologic model uncertainty; domain definition uncertainty; and parameter estimation uncertainty. Of these factors, typically domain definition is the most significant contributor to geometallurgical model variability. First, the fundamental supports for these models are briefly discussed, with domain definition emphasized. Second, two methods for uncertainty modelling are proposed. The first, more applicable to conceptual or early-stage projects, is a simpler and more expedient alternative that provides initial assessments of variability. This is intended to aid management in decision-making related to budgeting, including further sampling and testing. The second, a block-by-block approach that allows a detailed assessment of risk for specific designs and mine plans, thus providing further opportunities for mitigation. In the example provided, emphasis is placed in communicating this variability to both management and technical personnel in the form of “measured-indicated-inferred” indicators and also block-by-block confidence intervals.

Jun 25, 2023

By J de Cuyper, E. J. Parkins, H. L. Shergold, W. Freyberger

The paper is divided into two parts. The first part describes an investigation of the effect of temperature on the conditioning and flotation of an ilmenite ore with a 1:l oleic acid-fuel oil mixture as collector. During conditioning the pulp underwent characteristic changes of flocculation, deflocculation and dispersion which were monitored by measuring the power consumption of the conditioner motor. Optimum flotation results were obtained at the end of the deflocculation period. High ilmenite recoveries were obtained at high temperatures and high concentrate grades at low temperatures. The second part of the paper describes a study of the effect of temperature on the adsorption of oleic acid at the ilmenite/water interface. At high adsorption densities it was chemical and exothermic. Contact angles showed that the hydrophobicity of the collector-coated minerals increased with an increase in temperature.

Jan 1, 1976

By Brian J. Gorva

The key objective of forming a cartel is to increase profits to members of the cartel by taking the following action: a) control output; and b) control price. However, while attempting to obtain monopoly profits the cartel members have to contend with costs associated with cartelization and such costs include the following: political costs; the cost of coordinating output and price; organizational costs (such as cheating); and administrative costs (such as the cost of attending cartel meetings). The objective of commodity exchanges is to provide an open, free market where buyers and sellers may openly complete transactions and pricing information can be immediately disseminated. These transactions include the following: a) to provide facilities for "hedging", or transferring price risk from buyers and sellers of physical commodities to "speculators" through the medium of buying and selling futures contracts, and b) taking physical delivery of metal on due dates.

Jan 1, 1983

By F. B. Olender

Idler engineering, operation, and maintenance cannot be covered in depth in a short paper. Therefore, this will be a general look into the subject matter in light or the present-day technology. Depending on the source or reference used, belts for handling bulk material underground came into being between 1900 and 1920, while strip mining appeared in the thirties. The conveyor belt speeds in that era were in the 300 rpm to 500 rpm range. Belt speeds or 600-700 rpm were in vogue in the thirties, and the early sixties saw speeds or 800-900 rpm. Today, speeds or 1000 rpm are not looked at with dismay; in fact, speeds or 2000 rpm are being discussed. Among the driving forces moving the bulk materials handling industry to these greater heights have been the mining operators and engineers. Their appetite to increase output, yield, and reduced per-ton costs has constantly challenged the bulk material handling industry to develop products capable or handling these increased capacities. One or the products affected by this movement is the idler. Apart from the conveyor belt itself, it is one or the most significant parts or a conveyor system because or the sheer numbers needed in an installation.

Jan 1, 1971

By Rudrajit Mitra, Erik Hulthen, AARTI SORENSEN, TOBIAS HARTMANN, ELISABETH CLAUSEN

There has been an ongoing debate on how to transform engineering education to better prepare students for today’s professional world that is characterized by increasingly complex problems and challenges that engineers are tasked with upon entering the industry. While numerous publications have addressed possibilities of how experiential, problem-based, project-based and active learning can be integrated into the engineering curriculum, there has been little attention on mining engineering with respect to adopting this approach. This paper addresses the possibilities of integrating entrepreneurship education into mining engineering programs in order to foster discussion among academics from mining engineering on how to infuse value-creation experiences across the curriculum on a course, program and departmental level.

Sep 1, 2022

By R. D. Cook, J. L. Johnson

"Measuring mud bed level in a sedimentation device is an important control variable. Methods used to date for this purpose have had limited success providing continuous, consistent measurements at a reasonable price. This paper describes a new instrument for detecting the mud bed / liquor interface as well as bed density profiles. The state of the bed is measured directly with sensors located in the thickener. Data from bench-scale and full-scale tests show that the bed level is well defined and easily detected. In addition, full-scale testing revealed unprecedented information about thickener beds. Variation in bed density gave new insight into thickener bed dynamics, providing design and control opportunities never before possible. This novel instrument can significantly improve thickener control by providing reliable and consistent bed level measurements. It is also capable of measuring bed density profiles that can potentially identify significant operating problems early enough to take corrective action before experiencing costly shut downs. INTRODUCTION Numerous studies and papers have been devoted to the subject of thickener design and operation to achieve specified throughput and discharge densities. Mathematical models have been developed that present methods for sizing thickeners and predicting performance under varying process conditions. The compression effect of deeper beds on dewatering performance is a recognized phenomenon (Wilhelm and Naide 1981). This is one variable of many that are inter-related and influence thickener performance. For example in the steady-state, continuous operation of a thickener, if the solids feed rate increases and the bed level remains the same, the underflow discharge rate must increase with the result of solids concentration being lower. The interactions of these parameters are at the heart of thickener models. One such model (Burger and Narvaez 2007), predicts solids concentration profiles increasing downward and discontinuities between settling zones. This model uses sediment height (bed level) as a parameter that influences capacity calculations to achieve the specified solids concentration of the underflow. Knowing the bed depth is critical to maintaining stable thickener operation. Implicit in these modeling strategies are some basic assumptions such as homogeneous distribution of solids in the different settling zones, plug flow of solids through the settling zones and steady state operation of the thickener. The accuracy of these assumptions has not been verified because there has been little visibility inside the bed of full size operating thickeners. Testing of the instrument presented in this paper demonstrates that it provides a degree of visibility of the dynamics in a thickener not previously possible and indicates that the basic assumptions of the modeling strategies may not be completely accurate."

Jan 1, 2015

By BARBOSA AMILTON, Denise C. R. Espinosa, David B. Dreisinger

Chelating resins can be used to recover important metals from different sources, and it is important to understand which resin is most suitable for each metal [1]. This review  benefits the mining industry because chelating resins can be used to recover metals from low-grade ores and mining tailings, increasing the industrial process efficiency [2–4]. Furthermore, the use of chelating resins in mining processes and mining tailings has the common problem of metals contamination, with iron being the main contaminant in low-grade ores and tailings. Understanding how contaminants decrease ion exchange efficiency is significant for industries [5

By W. E. Lindquist

Roasting of refractory gold ores has the primary goal of oxidizing sulfides and organics to improve gold recoveries prior to leaching. Commercial installations currently utilize bubbling and circulating fluidized beds. The principle of flash roasting is aimed at a more cost effective method of whole ore roasting for large throughput applications. Results of pilot plant testing and scale up to commercial design will be discussed in further detail in this paper.

Jan 1, 1993

By Steven M. Bishoff

The reclamation of surface land areas disturbed during the course of coal recovery became a major, universal consideration upon the implementation of the Surface Mining Control and Reclamation Act of 1977. This legislation not only established reclamation as an absolute requirement, but also presented guidelines for reclamation standards and required bond-posting procedures to assure completion of the reclamation process. The Office of Surface Mining was established to enforce the provisions of the Congressional mandate by promulgating specifically detailed regulations and supervising the State participation in this regulatory process. The major operational consequences of the reclamation-related provisions of the Act and the OSM regulations are the increased costs and complex procedures necessary to accommodate the regulatory authorities. It is anticipated that many of these costs and procedures have not been adequately evaluated by either the coal operators or the regulatory bodies. It is, therefore, necessary to proceed with an examination of the general reclamation processes, the effect of these processes on product costs, and the methods, if any, which may be utilized to minimize their impact on the overall operation.

Jan 1, 1981

By D. A. Stanley

Researchers at BCD Technologies and the University of Alabama have applied three statistical techniques to the information contained in a large database of measurements from a phosphate ore processing plant. The rust, Principal Components Analysis (PCA), replaces many measured variables with a few fundamental and un-correlated variables. The second technique, Projection to Latent Structures (PLS), is an extension of PCA that explores the relation between variables identified as either independent or dependent. The third technique, Cluster Analysis (CA), is applied to the results of the PCA or the PLS calculations, and identifies individual data clusters that represent uniform operating conditions in the plant. All three statistical methods can be seen as geometrical operations on the data viewed as points in space. A Viewer gives a corresponding graphical presentation of the data points. This paper describes the use of the above three techniques and the Viewer to explore part of the phosphate flotation database.

Jan 1, 1998

By F. Soumis

We propose an advanced truck dispatching system which uses mathematical optimization approaches including integer programming, non-linear networks and the assignment problem. The system produces better operation control than existing algorithms. Furthermore, it provides planning tools for choosing equipment and finding an equilibrium between the quality and quantity of production.

Jan 1, 1986

By E. Kurt

The field of percussion rock drilling is subdivided into two areas of application; that which takes place on the surface and that which takes place underground. Surface drills are used in quarrying, highway construction, and maintenance work; underground equipment in mining and tunneling work. Two basic principles are involved in the operation of all percussion drills. First, the principle that reciprocates the impacting piston and second, the principle that causes the drill steel and bit to rotate. The back and forth motion of the piston is accomplished by a self-acting automatic valve that admits air alternately to each end of the piston (Figure 1). Drill steel and bit rotation is imparted by an integral ratchet mechanism (Figure 2) in the so-called "rifle bar" machines (Figure 1) or by a separate pneumatic motor in "independent rotation" drills (Figure 3). While rock drills are subject to all kinds of physical and operational abuse, they are most sensitive to faulty lubrication. Proper lubrication is the single most important factor in the longevity of a percussion drill.

Jan 1, 1970

By Kenneth P. Neumann

The development of the Cyprus Thompson Creek Molybdenum Deposit near Challis, Idaho, began in 1967 when the first mining claims were staked on the intrusive rock outcrop. Exploration drilling continued for the next 14 years. During 1978, a decision was made to develop the deposit. In December, 1980, approval of the Environmental Impact Statement was received and construction of facilities and waste rock removal began. By the middle of 1983, 126 M metric tons of rock had been removed and all facilities were completed. The high work ethic of Cyprus Thompson Creek employees combined with innovation has made the mine one of the most efficient in the United States today.

Jan 1, 1983

By P. Pages, J. Lombard, F. Fagnant, G. Bresson

This study is devoted to the improvement of the decision-making process in occupational protection of uranium miners in France. Its purpose is to apply the principles which are recommended by the I.C.R.P. in the field of radiation hazards. These principles, which have introduced the notion of "optimization" in standard setting, suggest the importance of applying cost-benefit and cost-effectiveness analysis to this sector. The objectives here are twofold : to evaluate the present organization of radiation protection on the basis of a simulation model of polluted air flow in the mine (due to the decay of a radioactive gas, radon) and to develop cost-effectiveness analysis of the various radiation protection policies.

Jan 1, 1981

By R. J. Gray

Oxidation of coal can best be described as a process of deterioration, since most of the uses of coal, such as for fuel and by-product chemical and coke production, are adversely affected by coal oxidation, and the inclusion of oxidized coal in most coal products detracts from their value. There are probably many mechanisms of coal oxidation, and the ways oxygen molecules combine as complexes with coal macromolecules to form new substances have been dealt with and speculated upon by many workers1)* but are not dealt with in the present work. This study deals with tests and methods of detecting oxidized coal, with particular emphasis on the microscopically discernible changes that accompany the chemical and physical changes that affect the technological properties of coal during oxidation.

Jan 1, 1974

By Katherine Hynard, Colin Eustace

Development quarterly mine plans is generally time-consuming and requires consideration for many operational constraints and competing objectives. With lengthy turnaround times, there is often limited opportunity to adjust the quarterly plan details to account for differences between actual state of the mine operation at the time of execution and expected state at the time that the plan was developed. Actual mining task completion times can vary significantly from the expected task completion times, due to many factors. In the absence of revision to account for differences between the planned and actual state, resource allocations and mining sequences, embodied in the quarterly mine plan may no longer be the best approach at the time of execution to achieve an efficient mining operation. Simulation and optimisation tools can be used to support rapid refinements for development and execution of weekly mine plans. When initialized with an operations data feed to establish the actual state of the mine operation, optimisation models can be used to facilitate both automation and revision of the quarterly plan to produce a weekly or daily plan for execution. This approach can remove much of the manual burden of revision if the existing quarterly plan no longer represents the best approach to meeting production objectives. Following initialisation with mining actuals, simulation models can provide a representation of the range of likely mine operations outcomes. The models can be used to accelerate the planning process by providing visibility of future performance and identifying likely operational issues. They can also be used to test the robustness of the plan with respect to performance variability and response to disturbances. Following identification of issues, simulation models can also be used for evaluating mitigation measures, through automated testing of alternative plans. Integration of mine data feeds with simulation and optimisation tools enables automated optimal responses to variations between the quarterly mine plan and actuals to be tested prior to release of and execution plan and implementation. The use of simulation and optimisation in weekly mine planning will be discussed in this paper with reference to surface mining examples.

Jun 25, 2023

By M. A. Trevits, G. Frampton

"Mine safety training materials have long included pictures of mine conditions, equipment, hazards, etc. These images are invaluable to both the trainee and the trainer to convey many important concepts. The human eye takes in a tremendous amount of information, while the field-of-view from a consumer grade camera is, generally, 40 degrees to 90-degrees. This difference in field-of-view is a primary reason that pictures, especially of dark and dusty areas, don’t adequately describe the scene. For conveying information to a trainee, these images lack context. Today, 360-degree cameras are available with consumer-grade cameras costing a few hundred dollars. Also, the display technology is already owned by most trainees and trainers and is widely available. The resulting 360-degree videos and pictures can be readily viewed on smart phones and inserted into Microsoft PowerPoint slideshows. These images and videos can easily be included in existing training modules, disseminated using the internet, and used by trainees easily. We propose a methodology for utilization of 360-degree video and images with simple display technology for miner training. INTRODUCTION AND BACKGROUND In mining, as in other production-related industries, the safety of workers is dependent upon many interrelated factors. One of the more important safety factors is a miner's ability to recognize hazards in their workplace. The ability to perceive and identify hazards is perhaps more difficult to master in underground mining than in general industry because the work environment is confined, noisy, dark, and inherently dangerous because of the hidden unknowns created by the geological setting and the conditions created by the mine opening. Further complicating the situation is a setting that is continuously changing as mining advances (Barrett 1995) [1]. Hours of excellent mine safety training have been developed and utilized over the years. Pictures of mines, activities, hazards, etc., are included in many of these training courses. These photographs, especially those taken underground, often lack context because of the limitations of the cameras and lenses. Notable research by the US Bureau of Mines and then later by NIOSH showed that the use of stereoscopic three-dimensional slides in training exercises was an effective aid for improving the ability of miners to recognize hazardous ground control conditions (Barrett 1988) [2]. An example of type of three-dimensional slides and slide viewer is shown in figure 1."

Jan 1, 2018

By William E. Mead

A regional investigation to find large supplies of potable ground water was carried out at elevations exceeding 12,000 feet above sea level on the Bolivian Altiplano. The program marked the first application of modern ground water search and development technology in the region, and ended a history of unsuccessful exploration efforts to locate important supplies of fresh water from underground sources. Oruro, a population center of 90,000 inhabitants, and its primary supporting industry - mining, both derived major direct benefit from the results of this program.

Jan 1, 1970