Search Documents

By Joseph Fernandez, Luminita Calin

INTRODUCTION The Tunnel and Reservoir Plan (TARP), commonly known as the Deep Tunnel Project, is the daring and unique concept developed by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) as a two-phase solution to the problem of waterway pollution and basement flooding due to sewer system backups created by the combined sewer over-flows (CSOs). Phase I, primarily for pollution control, includes the tunnels, shafts, connecting sewers and structures. These Phase I facilities intercept, during wet weather events, the CSOs within the MWRDGC TARP service area. The tunnels and shafts provide temporary storage of the CSOs for subsequent treatment at Water Reclamation Plants (WRP) before discharging into waterways. Ultimately, upon completion of Phase II, the tunnels, located from 45 m(150 ft) to 100 m (330 ft) below ground, will convey the CSOs to reservoirs for storage until WRP capacity is available. Phase II, which includes the reservoirs, pumping facilities, additional tunnels and shafts, has been planned to serve a dual purpose. The reservoirs provide storage of excess flows during wet weather events, those beyond the WRP capacity. Following the wet weather events, the stored flows can be conveyed, at controlled rates, to the WRPs for full treatment. These excess flows previously would have resulted in both overflows into the waterways and eventually backups in the local sewer systems. The storage capacity of the reservoirs also will promote the full utilization of the conveyance capacity of the tunnels and shafts, which in turn results in optimizing the conveyance capacity of the existing sewer systems. Therefore pollution control is further enhanced by allowing for capture of a greater volume of CSOs and greatly minimizing backups in the local sewer systems. The TARP project consists of four systems: O’Hare, Mainstream, Des Plaines, and Calumet, covering a total area of 971 km2 (375 mi2) and serving the City of Chicago and 51neighboring communities as shown in Figure1. With only two contracts left before completion of the Phase I tunnels, the 12.7km (7.9mi) Torrence Avenue leg, to be awarded in 1997, and the 12.4km (7.7mi) Little Calumet leg unfunded as of yet, both part of the Calumet System, the pollution control phase of the project is now 86% complete (Table 1).

Jan 1, 1997

By R. M. Smailer

Detailed description of the development of the FIOR process1 and, subsequently, other technical papers relating to the operation and start up of the FIOR plant2,3 are available in the technical literature. The Fluidized Iron Ore Reduction (FIOR) process plant constructed in the Matanzas region of Venezuela represents the first commercial application of this technology. The FIOR process was developed by Exxon Company during the 1950's and 1960's; and the facility in Venezuela was designed and constructed by Davy McKee with the plant start up in 1976. While there is a minority government ownership in the company, FIOR de Venezuela operates as a private sector company with the majority of the ownership being private capital.

Jan 1, 1981

By P. A. Korpi

In March of 1978 the first set of Angular Spiral Liners utilized in grate discharge ball mills for wet grinding was put into service in the San Flanuel Concentrator of Flagma Copper Company. The use of these liners has decreased grinding media consumption by 19.2% and grinding energy consumption by 15.8%. In addition a 1.1% increase in grinding throughput is being realized through the use of the system. This paper describes the Angular Spiral Lining System and reviews the test program at the San Manuel Arizona Concentrator. Operating parameters are discussed in addition to the current testing program to futher optimize the system.

Jan 1, 1982

By H. Kimura

A new technology for ironmaking based on direct gaseous reduction of iron ore concentrate is under development. The process is based on the flash reduction of the concentrate particles in a gaseous reducing agent, such as hydrogen, natural gas, a reducing gas generated by partial combustion of coal, or a combination thereof. This technology is expected to drastically lower CO2 emission and reduce energy consumption by about 38% of the blast furnace requirements. The energy savings are possible largely due to the elimination of pelletization and cokemaking. Process design and simulation using hydrogen as the reductant for iron ore concentrate have been performed. A process flow sheet composed of a flash reactor, heat recovery system, water removal system for purifying recycled hydrogen, and all connecting streams was evaluated using the METSIM software. Ironmaking using two reactors was also designed and simulated, which could reduce the total required amount of hydrogen although it would increase the complexity of the flow sheet and operation.

Jan 1, 2010

By W. Collingwood, K. V. Raj, S. Bandopadhyay

In the mining industry, computational fluid dynamics (CFD) modeling is used extensively to simulate air flow in underground mines. CFD modeling of pollutant transport in openpit mines is relatively new. Modeling the actual pit geometry of an openpit mine and the open domain is complex. The complexity is primarily due to the faceted geometry of an openpit mine with its numerous associated sharp features. Important issues that are not considered carefully at the geometry level are generally propagated to the subsequent processes. Several challenges and pitfalls are encountered in modeling pollutant transport in openpit mines. These challenges and pitfalls are related to the geometry, meshing, boundary conditions and turbulence modeling parameterization. An appropriate mesh selection is critical. A detailed discussion of the meshing of the domain of an openpit mine is presented in this paper. The selection of an appropriate turbulence model, such as kappa-epsilon (κ-ε), large eddy simulation (LES), Reynolds stress model (RSM), etc., to obtain the best possible solution is equally significant. This paper discusses the various challenges in modeling the pollutant transport process in an openpit and some of the approaches adopted to address these challenges.

Jan 1, 2013

By Debra Switzer, Swapnil Urankar, Douglas Watson, Steven Hunter, Chandranth Banerjee, Shashank Pathak

A hydrocyclone is a piece of equipment commonly used as a classifier in mill circuit operations. Traditionally, hydrocyclone performance is characterized by the classification efficiency parameter, such as cut size (d50c), sharpness of separation () and bypass (Rf ). A plethora of endeavors have already been made to develop parametric models to determine hydrocyclone performance that correlate design and process variables. In contrast to those studies, we made an attempt to develop an approach to derive required design parameters purely from hydrodynamic principles that provides a platform to optimize the operation of a hydrocyclone for a given application. In this selection methodology, we calculated the differential pressure at the air core, as well as the tangential velocity at the boundary of the air core from the vortex principle in a confined geometry at different operating regimes. A series of experiments were conducted using Weir’s Cavex® hydrocylone where process variables—such as solids concentration and feed flowrates—were experimentally studied to determine the key classification parameters. For the validation of the current approach we used the same process variables to derive design parameters and compared them with the existing design. The current approach can provide insights towards the selection of design parameters and can be useful for mining industry professionals to optimize different operating parameters of hydrocyclones to achieve the best performance.

Feb 1, 2024

By Hassan El-Shall

The results of laboratory and pilot plant testing of a newly developed process to dewater waste slurries from different industries are presented. Data indicate that an increase in solid contents from 6% to over 30% can be obtained in few minutes retention time in comparison to several years as required by currently used technologies. The economical as well as the environmental impacts of such process are discussed.

Jan 1, 1992

By Norm Greenwald

The Environmental Protection Agency ("EPA") has been attempting to develop a federal regulatory program for mine waste under Subtitle D of the Resource Conservation and Recovery Act since 1986. Recent regulatory and legislative events are now bringing this goal closer to reality. This paper discusses the mining industry's perspective on a number of the issues currently being addressed at EPA's Policy Dialogue Committee and in Congressionally-sponsored negotiating sessions.

Jan 1, 1992

By Sandip K. Mukherjee

In underground mining operations, ventilation and water sprays are the common methods of controlling dust. In recent years there has been a proliferation of technical literature dealing with water sprays for dust control. However, guidelines for the design of an effective water spray system have not been presented to the mining industry. This paper reviews developments in water spray dust control technology and recommends guidelines for water spray systems to control dust in under- ground coal and non-coal mining operations. These guidelines suggest type, number, location and orientation of nozzles, desirable operating water pressure, and associated filtration system.

Jan 1, 1983

By J. Davitt McAteer

Improvements in the control of coal mine dust have occurred over the past 25 years. Simultaneously, dramatic improvements in coal mine production technology have occurred, particularly at mines where longwall systems are in use. Production rates of longwall systems have quadrupled since 1978, and dust generation on these systems has significantly increased. However, technology to address control of the resulting increased levels of respirable dust has not kept pace, and many high-production longwall sections continue to experience problems with respirable dust control. This paper seeks to enlist the entire mining community in the effort to resolve the health problems presented by excessive levels of respirable coal mine dust, particularly on longwall systems. These systems are expected to increase in number and length, and to generate increasingly higher levels of dust as production rates of these systems continue to rise.

Jan 1, 1995

By Stephen P. Winkelmann

The expansion of gold production in Nevada's Carlin Trend over the last few years has been staggering. To increase gold production while minimizing capital requirements and providing for the safe and efficient mining and processing of ores has required a tremendous effort by the mine engineering group at Newmont Gold. Organizational changes were implemented by the company to effectively deal with a full range of engineering problems. Specially developed computer software and its applications will be explained in this article as well as improvements in the techniques used in converting geologic resources into reserves. Scheduling procedures for the mining of multiple pits to feed multiple processing facilities will likewise be presented. Ore control procedures and current mine engineering practices are discussed. Growth at Newmont Gold Expansion of production levels at Newmont Gold Co. was brought about primarily by the economic incentive to exploit increased reserves. From 1987 to 1989, mined production increased by 260%, gold production by 238%, and manpower by 166% (Table 1). These increases came quickly and demanded

Jan 1, 1990

By C. O. Brawner

INTRODUCTION My first major involvement on a rock mine slope stability project was in 1966 after I had become a principal of Golder Brawner & Associates in Vancouver, Canada. I received a request from Kennecott to evaluate two serious rock slope failures adjacent to the concentrator on their British Columbia molybdenum property near Alice Arm, BC, which was under construction. A rock slope up to 200 ft* high had been excavated at a design angle of 700. The inspection indicated that several large blocks of about 1000 cu yd each had failed on steeply inclined joint surfaces. Stability was reduced by extensive seepage caused by heavy rainfall. In addition, considerable overbreak had occurred, indicating excessive blasting had been used to excavate the slope. A program was developed to rock bolt potentially unstable blocks that could slide on dipping discontinuities. Some rock was scaled back to the inclined joints, and drain holes were drilled to reduce water pressures. The project was completed successfully and within reasonable economics. As a result of this success, enquiries were received regarding other mining projects. This indicated the potential demand for rock slope engineering. As a result, I took one month off to meet and discuss rock mechanics and slope stability with various people internationally. These included D. Coates in Canada, E. Hoek in England, K. John and L. Mueller in Germany, M. Rocha in Portugal, and the US Bureau of Mines in Denver, CO. Early misconceptions Based on involvement in projects during the next few years, it was concluded that there were a considerable number of misconceptions that existed among some geologists and mining engineers dealing with surface rock mechanics. Some of these included: • Water is a lubricant. This is incorrect. Water reduces the shear strength along discontinuities due to buoyancy, which reduces frictional strength. It also reduces the cohesion of clayey-type rocks. • The optimum pit slope angle in rock is 45°. The optimum slope angle for safety and economics is variable and is influenced particularly by structural geology, water pressures, mine blasting practices, and the depth and degree of weathering. • The flattest angle for slope stability is dictated by the angle of repose of broken rock, about 370. Where clayey-type rocks or clayey infill in discontinuities exists, failure can occur at much flatter angles, requiring flatter slopes or artificial stabilization. • Uniaxial and triaxial tests provide the necessary shear strength parameters to design rock slopes. Most failures in rock slopes are controlled by directional discontinuities. Therefore, the direct shear test is the correct test to evaluate strength parameters for most problems.

Jan 1, 1987

By M. G. Ayat, J. Dasher

Having an interest in coal slurry pipelines from a decade of arguments with Ed Wasp and crew at Bechtel about pumping thicker slurries slower, I immediately read this article and found nothing in it pertinant to the title. Ayat and Scott pumped five unidentified coals at 9% solids (50%-60% is the area of interest) in a 25-mm (1-in.) pipe around two square elbows through a 76-mm (3-in.) cyclone for up to 60 minutes and sized a large number of samples of unstated size on an unidentified wet screening device. They did not measure power consumption, discharge pressure, flow rate, or give pump tip speed or impeller diameter. They siad the cyclone had a "high" pressure drop (unmeasured) and did much of the degradation (measured) but more or less per unit of energy expended? Hargrove was not measured, so there are no data as to whether it would correlate with degradation. The authors conclude, with no attempt, correlation is "hard to establish." Please experiment before concluding. I am at a loss to know what "increasingly smaller size" means, much less what theory says such particles take "exponentially larger quantities of energy," which the authors neglected to measure. If such experiments without pertinent data or justified conclusions must be published, please attach a pertinant title.

Jan 1, 1990

By R. C. Emmett

Waste treatment in the mining industry is by no means a new problem to this field. In a sense, the entire process from ore to finished product is one of waste treatment - the separation of a relatively minor quantity of desired component from valueless material. Where it has been necess-ary or economical to practice conventional waste treatment or pollution control methods, such as dust collection, water recovery from tailings, or impounding of residues for future treatment, this has been done. Generally the containment of hazardous pollutants such as arsenic and cyanide also has been followed in modern times. But it is only recently, with the public outcry for the elimination of all forms of pollution, "that the industry has been forced to solve what often appears to be a myriad of difficult and costly waste treatment problems, or be faced with the alternative of closing down the operation. It is the objective of this paper to describe new as well as conventional approaches to these problems, specifically as might be applicable to liquid-solids separation methods. Host wastes in the industry are present either as solutions or slurries, or can be most advantageously handled by conversion to this form, such as in scrubbing noxious gases and dusts with water. Separation of the solids and purification of the aqueous effluents are, therefore, often the principle problems.

Jan 1, 1971

By John S. Newton

Modern high capacity underground mining machinery is a complex of mechanical, electrical and hydraulic components which have greatly increased capability over similar components of mining machinery of ten and. even five years ago. Looking into the future I feel certain in stating that there will be changes equally great in the coming five and ten year periods. With this premise in mind, I should like to bring to your attention some of the things that do and will have a continued major impact on the industry, particularly as they relate to the maintenance and operation of these machines of increasing capability. In underground mining today, nearly every individual plays a key role. A machine operator's importance in his work is comparable with that of the pilot of an airplane, a railroad engineman, a bus driver, a skilled machinist, a bulldozer operator and many others whose assignment is one of doing, by himself, with his hands and his brains all that the specially designed machine has been created to do. These machine operators are supported by a staff of skilled engineers, maintenance personnel, supervision, etc., but objectives are realized only when the operator maintains his schedule. What is being done and what can be done to make it easier for the operator to maintain his schedule which, as with the airplane, is constantly being improved? This question can be answered best, perhaps, by dividing the subject into four general categories - (A) Power Supply. (B) Control and Protective Devices. (C) Hydraulic Component Design. (D) Mechanical Design.

Jan 1, 1962

By P. T. Luckie

The selectivity curve -- a continuous function which predicts the expected proportion of feed material of a particular size that will appear as coarse material -- is the preferred model for describing classification. In a previous paper (I), the authors presented a technique for determining the selectivity curve of a classifier from experimental data. The separation process is defined by a binomial distribution of the form [ ] where s(x), the probability of particles of size x reporting to the coarse stream, is obviously the selectivity value for material of size x.

Jan 1, 1975

By Harold G. Arthur

INTRODUCTION Stillwater Tunnel construction is scheduled to start in the spring of 1973. The tunnel will be the site of an extensive program in rapid excavation research. This paper presents a progress report regarding our plans and relates the tentative decisions which have been made on how to carry out the research effort. The details are subject to revision as more input is obtained from other Government agencies interested in tunnel construction and from experts in industry and educational institutions. The objective of the research program is to bring about faster, less costly tunnel construction. This objective will be pursued through the development, improvement, and evaluation of various construction systems and investigative techniques. The need for this kind of program was recognized by the National Research Council, in its authoritative report "Rapid Excavation - Significance, Needs, Opportunities." (1) The Council advocated a federally funded $200 million, 10-year program to help meet the $69 billion market it expects in underground excavation between 1970 and 1990. The significance of tunnel construction to Reclamation is made clear by statistics of its tunneling experience and outlook. Reclamation has constructed 174 water conveyance tunnels totaling over 190 miles, Six tunnels are presently under construction which have a combined length of about 27 miles. There are on the books nine authorized, but unfunded tunnel projects totaling another 70 miles in length. Many more miles of tunnels are included in programs in various stages of investigation.

Jan 1, 1997

By J. M. Keane

The Solution Mining review arrived too late to appear in the May issue. Solution mining, in its broadest definition, includes all forms of leaching where a lixiviant solution is brought into contact with a metalliferous or non-metallic ore and the resulting pregnant solution is processed for recovery of the valuable soluble material. Technologies such as dump leaching, heap leaching, stope washing and in situ lixiviant solution injection and recovery fit into this definition of solution mining. A publication entitled the US Gold Industry (Dobra and Thomas) reflects the major impact that solution mining techniques have had on precious metal recovery. In 1989 (the last year for which statistics are available), the United States passed Australia to become the third largest gold producing country in the world after South Africa and the Soviet Union. It is estimated that when the final figures are in for 1990, the US will probably pass the Soviet Union in gold output. If the state of Nevada is ranked as a separate country, it will rank fourth in the world in gold production for 1990. A good proportion of this increase in gold production over the past few years can be attributed to the application of solution mining technology to low-grade, precious-metal-bearing material. Solution mining techniques have also made inroads in copper production. Many operations located at former underground mine sites employ in situ leaching as an adjunct to conventional dump and heap leaching practices.

Jan 1, 1991

By Dale A. Bivens

INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is currently being constructed for the United States Department of Energy in SE New Mexico. The purpose of the project is to store low level transuranic waste in an underground environment which will ensure a safe atmosphere for the life of the stored waste. Ohbayashi was contracted by the DOE to sink two shafts and underground drift development which will be used to conduct a series of long term experiments in order to finalize the suitability of the geology and the environment for the transuranic waste storage. The two shafts sunk at the WIPP site were excavated around a borehole by conventional methods. The excavation around a borehole eliminates some of the established blind bottom sinking techniques, but creates unusual problems which must be pre-planned and scrutinized closely. An analysis of the slashing to the borehole technique will be given. WASTE SHAFT The waste shaft (w/s) is 5.8 meters (19 feet) in diameter and will be used primarily to transport the radioactive waste to the underground storage area. A pre-existing 1.83 meter (6 feet) diam borehole was taken to a depth of 655 meters (2150 feet) to the existing drift; at this level, a 38 meter (125 feet) sump was installed using blind bottom sinking techniques. Geology The primary geology for the w/s excavation is redbeds, anhydrites, dolomite, mudstone and

Jan 1, 1985

By T. D. Rourke, E. J. Cording, O&apos

INTRODUCTION Detailed investigation of a 60-ft-deep excavation in a mixed profile of sands and stiff clay was performed by the University of Illinois for the Washington Metropolitan Area Transit Authority (METRO). The work was coordinated through DeLeuw, Cather and Co., the General Engineering Consultant of METRO. Instrumentation was concentrated in a portion of braced excavation for the Gallery Place Station near the intersection of 7th and G Street. The early construction date, the 60 ft depth of cut, and the proximity of large buildings formed the basis for selection of this site as the focal point of observation and measurement. A history of lateral and vertical displacement is provided wherein movements which occurred during excavation to the full depth of cut and, subsequently, during station construction and the removal of braces are described in detail. Observations of preloading and the consequent brace loads and wall displacements are described. The effect of temperature change on brace loads is discussed and the measured apparent earth pressure for the 60-ft cut is provided. The paper discusses the relationship of lateral displacements of the cut wall to the construction procedure, and compares the lateral wall displacement with both lateral and vertical movement in the surrounding soil mass. Based on observed movement, the method by which displacement was predicted for a nearby 82-ft-deep excavation is described. The performance of the 82-ft-deep excavation has been summarized elsewhere (2).

Jan 1, 1974