Search Documents

By D. A. Stanley

The Bureau of Mines has developed an equation which describes the dewatering of clay slurries with polyethylene oxide. This dewatering equation is An _ kC + b where n, k. and b are empirical constants and C is the concentration of polymer solution used for dewatering. The minimum amount of polymer required for dewatering. A is determined by titration of the clay slurry with a polymer solution. In this report, the dewatering equation is applied to data obtained for a polyacrylamide dewatering sequence. Fundamental similarities between the dewatering properties of clays and the viscosity of polymer solutions were observed. These similarities were explained by correlating an equation describing polymer configuration in solution with the dewatering equation. This correlation showed that amount of polymer required for dewatering and polymer solution viscosity are both consequences of the frictional interaction of entangled polymer coils.

Jan 1, 1989

By I. Longson

As a longwall coalface advances a caved goaf or waste region is left behind. Air flow takes place through this permeable goaf due to the pressure differentials existing across it and en route this leakage air picks up both heat and moisture. A marked deterioration in climatic conditions occurs in the face area at all points downstream of where this leakage air rejoins the main air-stream. This goaf heat source can make a very significant contribution, typically 30-40% to the rate of total heat pickup on an advancing UK longwall coalface with a VST of 40°C and hence on the climatic conditions that prevail at the return end and in the return gate of the face. The magnitude of the rate of heat collection from the goaf depends on a number of factors but it has been established that it is particularly influenced by the prevailing virgin rock temperature and the total flow rate of the leakage air. This paper proposes a model for the goaf based on a packed bed analogy and other assumptions required in order to evaluate the rate of heat pickup are identified. The outlet condition of the leakage air predicted by the model have been shown to correlate with underground measurements taken for a range of different production patterns with the face cutter at various locations on the face. The sensitivity of these predictions to variations in the input data has been tested and is commented on. At this stage of the development the capabilities and predictive limitations of the model are discussed. Further areas of investigation are suggested in order to improve the predictive ability and to extend the versatility of the model.

Jan 1, 1989

By J. E. Golsan

Barrick Gold Corporation installed an expert style control system on the grinding circuit at its Mercur mine. Barrick's main objective was to increase mill throughput by a minimum of 3%. The expert system team collected operating data and then created a knowledge base using Comdale/X expert system development software. The expert system moved from on-line "advisory" mode, testing of expert rules, to full process control in four weeks. Expert system control benefits include a 9-15% increase in mill throughput, consistent mill loading leading to less wear on SAG mill parts, and improved downstream process control.

Jan 1, 1998

By D. Lenartowicz, K. R. Alexander, M Collings

Cosmo Howley is a gold deposit in the Northern Territory of Australia. The geology is complex and the input of geological data is an important part of the grade control process. As the geology of the deposit has become better understood, grade control and mining techniques have evolved to meet the changing circumstances. Present grade control depends on the use of angled blast holes, 21/2 benches and selective mining. Data is processed on site using 2 386 PC's running Surpac software. An environmental protection programme is employed, including soil stripping and stockpiling, sulphide waste containment and water quality monitoring.

Jan 1, 1989

By V. G. Hill

The term bauxite was first used by O.P.A.P. Dufrenoy in 1845 for an ore which was discovered by Pierre Berthier in 1821 near the village of Les Beaux de Provence near Arles in southern France. His data suggested that this mineral was an alumina hydrate with two molecules of water. However, it was subsequently shown by thermal analysis that the mineral was a fortuitous mixture of the mono-hydrate and the tri-hydrate. Diaspore had been previously discovered in 1801 and gibbsite in 1822. The term was however retained as a rock name. The name of the village was changed to Les Baux around 1885; Sainte Claire Deville suggested that the mineral name should reflect this, and it was changed to bauxite (Bracewell, 1962, Rkgnier, 1988). Mining of bauxite began around 1860 in the Auriol region in the Bouches du Rhine area in the south of France. This ore was transported toMarseilles by carts and was processed in the Salindres plant, which at that time was the only plant producing alumina using the Deville process and aluminum by the chemical process. During that period white bauxite (low iron content) was particularly sought after for the production of aluminum sulfate, refractory bricks, and quick setting cement. Export of bauxite from France began in 1880 and was initially delivered to Chemische Fabrik, Goldschmischen near Breslau, and to Guilini's Ludwigshafen plant in Germany in 1885. These companies produced alum and aluminum sulfate (RCg- nier, 1988). The next bauxite mining operation was in Antrim County in Northern Ireland in 1873. This was first used for the manufacture of alumina refractory bricks and quick setting cement (Bracewell, 1962). It is important to emphasize that initially almost all of the bauxite which was produced came from France and was mainly used for non-metallurgical purposes. At that time even the production of alumina was mainly for use as a mordant in textile dying. However, with the development of the Hall-Héroult process, the alumina which was available was increasingly used for smelting to aluminum. In spite of this the demand for non-metallurgical bauxite continued to increase and a set of applications were developed. These include refractories, abrasives (including the recently developed proppants), high alumina cements, aluminum chemicals, activated bauxite, and alumina. It became increasingly evident that the high alumina-low alkali raw materials have special advantages. The question however was one of cost benefit. Chin (1989) has pointed out that the non-metallurgical operations have been traditionally grafted on a bauxite/alumina/aluminum industry tree. In this context the non-metallurgical alumina produced was, with few exceptions, regarded as either coproduct or byproduct i.e.: Bauxite Trunk Sector Alumina Trunk Sector Aluminum Trunk Sector

Jan 1, 1994

By A. M. Johnson, M. A. Cornachione

The west central Upper Peninsula of Michigan contains a large resource of graphitic slate. The slate has potential industrial use as a substitute for shale currently used in the production of portland cement. Some of the unweathered slate, however, has a high concentration of pyritic sulfur that can create emission problems when processed in a kiln. A low-cost method to reduce the sulfur content of the slate through the optimization of pyrite oxidation in a bio-heap leaching operation was investigated. In this study, optimal conditions for the bacterium Thiobacillus ferrooxidans were created to promote pyrite oxidation and, therefore, sulfur removal from the slate. Preliminary lab scale flask tests using crushed and sized slate (-40 + 100 mesh) and T. ferrooxidans bacteria in a sulfuric acid medium resulted in 70% oxidation of pyrite over a one-month period. Subsequent column leaching tests on coarser materials (-3/8+1/4 in.) operated for six months resulted in a maximum reduction of total sum of 75%. These data suggest that bio-heap leaching to remove sulfur from the slate for use as a kiln feed material is viable.

Jan 1, 1995

By Earle J. Klohn

Tailings disposal has rapidly become an area of increasing importance to both existing and planned mining operations. In recognition of the significance of this topic, MINING ENGINEERING is presenting a series of articles on tailings disposal. The first, published in June, outlined some site criteria that influence tailings disposal and some of the design options available to meet these criteria. The following article explores in more detail important design criteria for tailings dams and provides several case study illustrations.

Jan 7, 1981

By C. J. Kirkland

The paper describes the arrangements for the casting, curing and handling at the casting yard, of the concrete segments for the lining of the UK half of the tunnel, and the plant used for the handling of these linings at the construction site. An outline of the tunnel boring machines being used is given, with particular reference to lining handling and erection, and the extensive muck disposal systems installed. A general progress update will be given to the conference.

Jan 1, 1989

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001

By D. M. Anderson

The current mine closure process is faced? with the formidable challenge of controlling environmental and legal liabilities that are associated with mine closure. The current level of environmental statutes and regulations, and the legal/liability considerations, has evolved through regulatory enactment of mine reclamation laws and other existing environmental laws, such as the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). Management tools and techniques to limit risk exposure and financial losses should be employed as an active measure throughout the mine life, including closure and post-closure.

Jan 1, 1995

By G. Reed Marchant

In 1967 the US Congress passed the "Clean Air Act." This act was amended in 1970. As a result it soon became obvious that American industries were going to have to make significant changes in their methods of operation to be able to comply with quickly developing federal regulations. One of the first regulations developed was on sulfur dioxide. For this reason, the nonferrous smelting industry was immediately affected by these new regulations. This is true because the smelting process produces sulfur dioxide as a natural product of combustion when the sulfur-bearing ore is oxidized to purify the metal. The federal government's approach for setting standards included public hearings at which government, industry, and private citizens were allowed to make comments. For this reason, it was apparent to Kennecott's Metal Mining Div. that it was desirable to make a maximum effort in working with the agency to see that correct input was provided at the hearings to assist the government in setting fair and realistic standards. It was also obvious that more complete monitoring would be required. It soon became apparent that the efforts required input from many levels of the corporation from the chief executive to the plant operators. In order to accomplish both the administrative and the technical needs, an organization was needed that could respond quickly to these needs, obtain information from diverse sources, and bring it to focus in an organized approach to the problem.

Jan 1, 1979

By James A. Martin

Evaluation and subsequent development of a quarry in east-central Missouri was based on a general but brief examination of outcrops and core from five (5) test holes. Neither core, outcrops, nor existing quarries in the general area gave any indication of potential major problems. In the third year of operation large areas of collapse rubble, consisting of green shale and large blocks of limestone and sandstone, were encountered. Their size and random distribution resulted in both blasting and quality control problems. By the fourth year of operation, production costs became prohibitive and the site was abandoned. Prior to dismantling the plant a geologic investigation, which included shallow seismic and resistivity surveys, was made of the unmined portion of the lease. The collapse dolines appear to be related to structure and predate development of the modern topography. Surface indications of these features are few. The seismic profiles were especially helpful in plotting their distribution. Geologic relationships and seismic data developed at this site are being related to similar suspect areas in Missouri and have been useful in their evaluation.

Jan 1, 1970

By B. K. Cantrell

A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2, NO, NO2, SO2, diesel-exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive, but during the past several years, progress has been made in defining the problem. Results from epidemiological studies by Garshick, et al. (1988); animal inhalation studies by Mauderly, et al. (1986); Iwai, et al. (1986); and Brightwell, et al. (1986); and in vitro studies by Lewtas, et al. (1986), have provided sufficient data for the National Institute of Occupational Safety and Health (NIOSH) to recommend that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration," NIOSH (1988). NIOSH further stated that "though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk."

Jan 1, 1990

By F. Sachanidis

The lignite surface mines of Ptolemais basin operate according to special environmental terms regarding the concentrations of heavy metals and trace elements in water discharges. Based ?n the results of lab analyses and in-situ measurements conducted so far it is concluded that the concentrations of heavy - toxic metals and other trace elements are low or negligible. The deviations from the upper concentration limits specified by laws and regulations are rare and non-systematic both on their spatial or temporal distribution. The same results prove also the relation between water quality and type and nature of the sediments forming the Ptolemais basin and the carbonated and metamorphic rocks forming the surrounding mountain areas.

Jan 1, 2006

By R. Hagemeyer

In North America, the paper industry is by far the largest consumer of coating and filler mineral pigments. Present use is at an annual rate of 5.5 million metric tons with a value of $660 million. Current estimates are 65 percent is used in coating and 35 percent in filler applications. During the past decade, the switch to alkaline papermaking has provided the opportunity to substantially increase filler levels while maintaining paper strength. As a result filler consumption has been growing at a late in excess of 15 percent yearly. Unfortunately, within a few years, mandated recycling could slow or even reverse this trend. The critical issue is finding an economically viable method for recycling the mineral pigment and/or minimizing the disposal problem

Jan 1, 1994

By Elisa Comis, Barbara Bitetti, Julien Pepiot, Stefano Lione, Francesc Rich

The new Lyon-Turin railway project involves the construction of a 57 km twin-tube tunnel between France and Italy. Pini France (project leader) and Systra-SWS are the designers of Construction Site 8 (CO8). This part of the project includes the construction of the tunnel portal on the Villard-Clément platform, two 2.8 km long tubes of the base tunnel in the direction of Saint Martin la Porte, the cross-passages between tubes and the niches. This paper presents the general approach followed to design the temporary support for the base tunnel, cross-passages, and technical rooms. The design of the temporary support accounts for the variability of the ground and water conditions, the excavation attended behavior, the construction planning and the identified geological hazards that could be encountered along the alignment. Particular attention is paid to the intersections between the tunnels both in terms of numerical modelling and construction methods and phases. Two types of intersections are present in the project: the intersections between the cross-passages and the base tunnel and the intersections between the base tunnel and the niches. 3D models have been developed for the tunnel intersections.

Jun 23, 2024

By William L. Carter

Through your presence here this morning and your membership in the Society of Mining Engineers, you have shown that you are interested in keeping abreast of the latest technology and mining procedures, want to be part of the continuing progress made by those in your profession, and are looking for ways to participate in expanding your professional and personal experiences and skills. All of these factors are part of your continuing education, the need for peer identification or recognition, and the desire to make a specific contribution to strengthening your profession. However, you may be here with or without your company support and financial backing, unless you are self-employed. Whether you are here for the above reasons, or for many others, your presence reflects a recognition of the importance of participating in the organizational structure of your profession.

Jan 1, 1981

By M. Katzer

The effect of selective dispersants as wet grinding aids for ores is demonstrated on laboratory scale batch and continuous grinding equipment. A complete characterization of behavior is performed on a given ore to demonstrate correlations involving torque, % solids, net production rate, and slurry weight and volume loading. The relationship between such laboratory data and industrial scale testing results is very consistent.

Jan 1, 1979

By L. A. Roe

The year 1867 marks the first year of commercial production of phosphate rock in the United States. South Carolina produced almost all of the domestic output of mineral phosphate until phosphate mining began in Florida in 1888. During the period 1868 to 1949 the total marketed production of domestic phosphate rock was about 186 million long tons of which 71.5 percent was produced in Florida, 18 percent in Tennessee and 7 percent in South Carolina (1). From 1949 through 1960, Florida phosphate rock production has ranged Prom 71 to 77 percent of the total domestic production. Since three-fourths of the domestic phosphate production is from the Florida field, and since most of the phosphate from the Tennessee and Western fields is not processed, but used directly as electric furnace burden, this paper will concern itself almost entirely with water requirements for mining and processing ore from Florida. Figure 1 summarizes phosphate rock production for Florida vs. total United States production over the period 1947-1960.

Jan 1, 1962