Search Documents

By W. A. Rickelton

Trialkylphosphine sulphides, in contrast to their well known oxide analogues (1,2,3,4), have received comparatively little attention as metal extractants and previous studies have been biased toward analytical rather than commercial solvent extraction applications (5,6,7). The sulphides are soft Lewis bases and only from complexes readily with the limited number of metals in the periodic table which can be classified as soft acids (8) e.g. Ag+, Hg2+ and Pd2+. Consequently, these compounds tend to be more selective than the broad-spectrum, hard-base, phosphine oxide extractants such-as TOPO (trioctylphosphine oxide). The purpose of this paper is to describe a potential application of one phosphine sulphide, CYANEX® 471X extractant, in the selective recovery of silver from base metal sulphate solutions. CYANEX 471X is triisobutylphosphine sulphide (TIBPS).

Jan 1, 1984

By N. Sahin, M. Can, Z. Ekmekçi, Y. Öztürk, Ö. Biçak, I. B. Çelik, B. Kocabiyik

"In this paper, a case study from Çayeli Bakir Isletmeleri A.S. (Rize, Turkey) about the selective flotation of copper minerals from sphalerite is discussed. Çayeli Cu-Zn Sulfide Ore contains different ore types, such as yellow ore, clastic ore, bornite-clastic ore, bornite-yellow ore, and black ore. For some of these ore types, selective flotation of copper and zinc is very difficult presumably due to presence of secondary copper minerals such as bornite, chalcocite and covellite, and also surface oxidation. These factors affect Cu-Zn selectivity due to activation of sphalerite particles in the ore during the process. The main objective of this work was to improve Cu-Zn selectivity by optimization of the pulp chemistry for different ore types of Çayeli ore. After preliminary flotation tests investigating effects of different chemical conditions, a plant survey was performed to determine the plant performance and sources of the problems when problematic bornite-clastic ore is treated in the plant. Various chemical conditions are tested in the laboratory scale test for better depression of sphalerite in copper flotation circuit. Combination of Na2S+ZnSO4+MBS was found to be the most effective depressant scheme. INTRODUCTION Ore variability is one of the most important factors affecting performance of a process plant both in short and long term planning. The geometallurgical modelling becomes a common tool to determine ore variability problems and develop the most efficient solution during life of mine (1, 2). Flowsheet design and equipment selection and sizing are usually done based on the results of ore variability test works. However, in some cases ore variability may not be foreseen during the design stage and therefore the solutions should be developed based on the existing flowsheet and equipment in the plant. In this situation, ore characterisation, problem statement and diagnostic testing should be applied step by step. The problem could be due to changing feed grade, mineralogical characteristics, grindability and surface characteristics when flotation is involved. The variability in feed grade with fixed mineralogy can be handled with relatively simple modifications (i.e. adjusting throughput or equipment capacity) in the plant. Variability in ore mineralogy is the most complex and difficult problem to tackle. Because, mineralogical variations could bring variations in mineral composition, texture and liberation. These variations can potentially lead to the variations in grindability of the ore and flotation behaviour. Variations in grindability are usually managed by optimization of operational parameters in grinding circuit, as it would be costly to replace the existing equipment in the circuit (3). The variations in flotation behaviour are mainly due to variations in mineral types and distribution, texture and surface oxidation. One or all of these factors could be observed in a flotation operation. Therefore, a comprehensive investigation both in plant and lab scale should be conducted for definition of source of the problem. The testwork to solve the problem and retrieve the performance is planned and conducted depending on the source of the problem (4, 5)."

Jan 1, 2017

By P. Bissert, M. Klein, L. Yan, D. Yantek

"Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hrs. One of the main concerns with the use of mobile RAs is the heat and humidity buildup inside an RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in a fully occupied RA must not exceed 95°F. To investigate this issue, the National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4°C (17°F) and the relative humidity (RH) approached 94 %RH. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the average air temperature inside the RA at the end of 96 hours to within 0.6°C (1.0°F) of the average measured air temperature. INTRODUCTION If an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke, or even death. In its 2007 report to Congress, the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) recommended that RAs should be designed to ensure that the internal apparent temperature (a temperature-humidity metric) in an occupied RA does not exceed 35°C (95°F). However, a standard method to determine compliance with this metric does not exist. The heat transfer process within and surrounding an RA is very complex, and is not easily defined analytically or experimentally. To investigate the related issues, OMSHR conducted heat and humidity testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. During the testing, numerous parameters were measured: heat input to the chamber, the air temperature and relative humidity inside the RA, the air temperature in the mine, the mine strata temperatures versus depth, and the airflow inside and outside the chamber. The focus of this paper is on the temperature rise within an RA. TAITherm heat transfer analysis software was used to develop a thermal simulation model of the RA as it was tested in the mine, using the test results as the benchmark. Both sensible and latent heat were used in the test and the model."

Jan 1, 2016

By Clyde M. Pearce

This paper describes the facilities at Pointe Noire, Quebec that Wabush Mines utilizes for the receipt, distribution, stockpiling and shipping of iron ore concentrate and pellets. The main topics to be covered will be: 1. - General description 2. - Concentrate receiving facilities 3. - Conveying circuits 4. - Stockpiling 5. - Vessel loading GENERAL DESCRIPTION The map of the eastern Quebec - western Labrador area as shown in Appendix #1 shows the location of Wabush Mines properties. You will note the Scully Mine located at Wabush Lake, Labrador, 235 miles north of the town of Sept-Iles, Quebec. Our neighbors, the Iron Ore Company of Canada have their properties further north at Shefferville, near by at Carol Lake and at Sept-Iles. To the Southwest, our other neighbors, Quebec Cartier Mining, have their iron ore processing facilities and their terminus on the St-Lawrence at Port Cartier. Concentrates are prepared at the scully Mine by mining, crushing, grinding, concentrating, drying and high tension separation for shipment by rail to Pointe Noire, Quebec. Pointe Noire is situated across the bay from the town of Sept-Iles, Quebec on the North Shore of the St-Lawrence River. The concentrate consists of 66% iron, 2 ¼ percent silica and practically no moisture, permitting the use of specially constructed railroad cars and handling facilities to convert the concentrate into pellets, the final product.

Jan 1, 1967

By A. H. Kaksonen

Numerous reactor designs for biological sulfate reduction have been reported. Fluidized-bed bioreactors (FBR) can efficiently retain biomass and allow high mass transfer and reaction rates. This work reviews the development of various sulfate-reducing FBR processes for treating acidic metal- and sulfate-containing waters and recovering metals from bioleaching liquors. The FBR process performance was evaluated with continuous flow experiments under various operational conditions: fluidization rates, influent pH values, metal, sulfate and salt concentrations, hydraulic retention times, electron and carbon sources, and temperatures. Substrate utilization and sulfide inhibition kinetics were determined with batch FBR-kinetic experiments. An artificial neural network (ANN) model was used to predict the performance of the FBR. Sulfate-reducing bacteria (SRB) were characterized in FBRs with molecular and culture-based approaches with the aim to gain a better understating of the bioprocesses. Based on the studies, FBRs are well suited for the combined removal of metals, acidity and sulfate from water.

Jan 1, 2010

By James L. Withiam, P. C. Kelsall

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium.

Jan 1, 1986

By Kenneth K. Humphreys

Over the past four years, the Coal Research Bureau of West Virginia University has presented a number of papers on operations research in the coal industry before various AIME meetings and meetings of other societies. These papers have been followed up by further presentations in the technical press. The emphasis of all of these papers has been to demonstrate applications of operations research to the solution of numerous types of coal industry problems. In each case, effort has been made to demonstrate that operations research does not require extensive knowledge of computer science or use of sophisticated higher mathematics. In fact, for most applications, satisfactory results can be obtained by a single individual in a minimum of time with no aids other than a pencil and paper and a knowledge of basic arithmetic. The most recent efforts by the Coal Research Bureau have been directed toward the continuing industry problem of optimizing the location of mining facilities. Preliminary work in this area was presented before the Central Appalachian Section of AIME and subsequently published in the May, 1972, issue of Coal Age. This initial presentation illustrated techniques for determining optimum locations of facilities based upon material transport effort under the assumption of constant cost per ton mile of haulage effort. The present paper will expand upon this earlier work and introduce economic factors. In the design of a mine or mining system, careful consideration must be given to the sites selected for each element of the system. Optimum placement of facilities is vital to minimize capital and operating cost. Thus, barring unfavorable geological conditions or other exceptional factors, facilities should be located at those points which represent the minimum cumulative cost over the life of the property. Most cost factors are independent, or essentially independent of the location of fixed facilities. Thus, for example, regardless of the location of the shaft, the direct cost to mine any given ton of coal is essentially constant. The major 1

Jan 1, 1972

By Siyu Song, Yanhong Wang, Guohua Gu, Linbo Huang

In this study, the effect of cations, Na+ and Mg2+, in saline water on copper flotation in the presence of calcium bentonite was investigated. It was found that as the concentration of NaCl was increased, the copper recovery initially decreased and then increased to above 99%, while the copper grade initially increased and then decreased. In contrast, as the concentration ofMgCl2 was increased, the copper recovery continuously increased, while the copper grade continuously decreased. The variation of copper recovery and grade was mainly attributed to the synergistic effect of pulp rheology and flotation solution chemistry. The underpinning mechanisms are the compressing electrical double layer and ion-exchange interaction between saline water and bentonite, which occur at the same time. Using salinewater slightly affected the pulp rheologywith a decrease in copper recovery at low NaCl concentration. Increasing the concentration of cations in saline water might even facilitate the flowing out of exchangeable cations, especially divalent cations, from the interlayer space of bentonite to the solution, resulting in the decrease of copper grade at high salt concentration.

Sep 10, 2020

By T. V. Durkin

Approximately 1,390 t (44.7 million ounces) of gold have been produced in South Dakota since 1875. South Dakota's mining laws attempt to strike a balance between economic development and environmental protection by promoting mining as an industry while requiring prevention of pollution and reclamation of affected lands to a beneficial use. The mining laws have evolved since their inception in 1971, especially in response to gold mining. The laws have remained flexible to meet changing regulatory needs. Gold production has continued relatively unabated, even in the face of public scrutiny, two mining moratoriums, and isolated environmental problems. The department's system of "one-stop-shopping" for environmental permits streamlines the permit process, fosters quick resolutions to compliance problems, and helps keep enforcement actions out of the courts. Specific case histories at heap leach mines within the Black Hills are presented.

Jan 1, 1998

By S. K. Singh

"Feather edging"-a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar ('total') extraction coal mine.

Jan 1, 1999

By Yang Song, Li Shaokang, Wang Zhiqiang, Wang Jinjun, Li Guofeng, Su Meixuan

CaCO3, as a component widely existing in natural minerals, is a common impurity. In recent years, triboelectric separation has been applied to the separation of minerals containing CaCO3. However, the CaCO3’ s tribocharging mechanism is still unclear and the charging effect of CaCO3 is not obvious. In order to study the effect of triboelectric charging of CaCO3 particles under different conditions, according to the single particle frictional collision charge-mass ratio formula derived from the condenser model, an experimental platform for particle tribocharging was built in this paper. Then, the formula of charge-to-mass ratio (Q/m) was derived based on the analysis of the particle force. Particle image velocimetry (PIV) was used to record particle motion trajectories to calculate the Q/m of one particle by this formula. In the experiment, the airflow velocity, tribocharge material, and moving distance of the particles were varied to investigate the variation of the particle charge-mass ratio results. The results show that CaCO3 was negatively charged when tribocharging with mental. The particle’s Q/m is positively correlated with the airspeed. When the metal is triboelectrically charged with the insulator, the metal with a smaller work function leads to the insulator particle with a larger Q/m. As the moving distance of the particles increases beyond 230 mm, the particle charge ratio decreases. The particle charge-mass ratio is consistent with the trend of the charge-mass ratio deduced from the capacitance model.

Jun 3, 2023

By J. A. Barrera-Godinez

Traditional batch flotation tests produce a limited number of data points from which to evaluate the kinetics of the process. In this research, continuous weighing of froth, from a modified circular flotation cell, using a computer/data acquisition system., has been coupled with chemical analyses from intermittent froth sampling. This combination has permitted the experimental data to be smoothed such that the flotation kinetic parameters could be determined with enhanced confidence. To demonstrate the procedure, a galena ore was floated to permit flotation kinetics to be investigated as a function of cell parameters. It was shown that the kinetic data of this lead flotation most closely correlated with the Huber-Panu three parameter model. In addition the results illustrated the effect of froth thickness, froth scraper rate and air flow rate on the cell performance, in terms of mass flow, grade and recovery.

Jan 1, 1990

By S. S. Peng

An expert team consisting of geology, civil, and mining engineer professors was organized to investigate several problems of longwall mining in three mine sites including: site investigation, panel layout and support selection, overburden strata movement, surface subsidence and structural damages, slope, stability, well and stream dewatering, etc. The results include the development of a PC software package such as powered support selection, Surface subsidence prediction, optimum panel dimension, and pillar design.

Jan 1, 1989

By William Gleason

From Nov. 16-20, the Extraction 2025 Conference will be presented in Phoenix, AZ. The unique conference brings together the 12th International Copper Conference, the 6th International Symposium on Nickel and Cobalt as well as cross-cutting symposia. Extraction 2025 is co-organized by The Metallurgy and Materials Society (MetSoc) of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM), the Society for Mining, Metallurgy & Exploration (SME) and The Minerals, Metals & Materials Society (TMS). The previous, and first Extraction meeting (Extraction 2018) was held jointly by these three societies seven years ago in Ottawa and was a huge success with more than 90 percent of respondents indicating interest in attending a future event. Kimberly Mills, senior process engineer at Samuel Engineering, is the lead for SME. “This installment of Extraction is featuring Copper 2025, Nickel-Cobalt 2025 as well as crosscutting symposia,” said Mills. “All three societies participate on the International Organizing Committee for the Copper Conference Series and are well situated to host this event together. TMS is also hosting the Ni-Co conference this year and agreed to include it as part of Extraction. There are many aspects that can be shared between these commodities to share information on processing technologies and to learn from each other.” SME is the overall conference chair and running the logistical aspects of the event, which includes managing all aspects of the venue and the registration system as well as tours and short courses, Mills said. “SME has many dedicated members serving in various capacities on organizing and programming committees, including Nick Gow serving as Technical Committee Co-Chair for Copper and Adam House assisting on the Copper IOC.” When Extraction 2025 kicks off, it will be focused on the metals needed for the global energy transition with a special focus on copper and nickel-cobalt. “With as rapidly as the industry is changing and the huge demands for these metals we have some serious challenges ahead of us,” Mills explained. “These challenges require collaboration, creative solutions and engaging experts, both inside and outside of our fields, with a push for sustainable sourcing, ethical supply chains, environmental and social responsibility.” The International Copper Conference was started in 1987 as a collaboration between the Institute of Mining Engineers of Chile (IIMCH) and MetSoc of the CIM. The event is typically held every four years and has always been held as a standalone or headlining event at a society annual meeting, said Mills. “Over the years, this conference series alone has brought together members of IIMCH, MetSoc, TMS, SME, the Society for Metallurgists and Miners from Germany (GDMB), the Mining and Materials Processing Institute of Japan (MMIJ), the South African Institute of Mining and Metallurgy (SAIMM) and the Nonferrous Metals Society of China (NFSOC),” she added. “Being a part of Extraction allows for even more sharing of ideas and expansion of networking. This conference has not been held in the United

Oct 1, 2025

By W. E. Lamont

As part of its program to minimize mineral and metal needs, the Federal Bureau of Mines conducted investigations to determine the feasibility of producing foundry-sand-grade olivine concentrates from low-grade sources. Using a Bureau-patented attrition-grinding technique, concentrates meeting Steel Founder's Society of America (SFSA) specifications for loss on ignition (LOI) were prepared. Studies showed that green strengths and tensile strengths of the attrition-ground olivine were equivalent or superior to those of commercial materials. Metal-casting studies showed that molds of attrition-ground olivine produced better surface finishes. The improved surface finishes were attributed in part to increased grain sphericity.

Jan 1, 1977

By Daniel A. Wasson

A review of the history of boosters is given with examples of the prominent types that have been made commercially. The performance and design features of protected core boosters are discussed in detail. A new gel booster is discussed with its advantages to the mining industry. Booster size, hole configuration, performance and safety aspects are reviewed. Important features of boostering in above ground and underground blasting are related to an economic analysis. This presentation will cover different types of boosters commonly used in mining. However, for the purpose of this paper a few terms need to be defined to clarify the action of different parts of a priming system. Booster* - "Any unit of explosive or blasting agent to be used in a charged hole for the purpose of perpetuating or intensifying the initial detonation". Primer* - "A unit, package or cartridge' of explosives containing a detonator or detonating cord which is used to transmit detonation to other explosives or blasting agents". Detonator - A device for initiating a detonation from a flame or a small electric current, the former being represented by a fuse cap and the latter an electric blasting cap.

Jan 1, 1981

By M. Misra

A sample of thorium-contaminated soil from Kirtland Air Force Base (AFB) was subjected to froth flotation for removing thorium contaminants. A series of flotation tests were conducted to screen and evaluate the reagents. Among the collectors used, sodium oleate exhibited to show the promising results. Preliminary tests showed that a concentrate having activity as high as 5300 pCi/g can be obtained from the contaminated feed soil having activity 800 pCi/g. The volume reduction obtained was 89% and the activity recovery in the concentrate was 68%. The paper discusses the physico-chemical characterization data and the potential physical separation decontamination schemes for the thorium contaminated soils.

Jan 1, 1996

By Raymond E. Krauss

The McLaughlin Mine is a world class epithermal gold deposit located in the coastal thrust fault of Northern California, U.S.A. Homestake adopted a proactive strategy in the permitting of the Mine. Extensive environmental baseline studies were undertaken. Engineering and process alternatives were evaluated for environmental impact along with other factors. A unique pressure oxidation process was selected. Screening studies were conducted as a basis for the selection of waste rock and tailings disposal sites. Project engineering and permitting were fast tracked. Construction required eighteen months, and the first gold bar was poured in March of 1985, six years after the initial discovery. Project facilities are designed and operated so as to minimize environmental impacts. A comprehensive monitoring program demonstrates permit compliance. Reclamation of the site is ongoing throughout the Mine's twenty year life. Nonmined lands are managed to maximize wildlife habitat value.

Jan 1, 1990

By Harry Verakis

Electronic detonator systems are an advance in technology beyond conventional electric detonators for initiating explosives and blasting agents. Their use is widening into the mining operations of the U.S.A. Each electronic detonator system differs in design, construction, operation, and testing features and each system is different than “conventional” electric detonators. There are benefits of electronic detonator systems which serve to improve blasting safety. With the introduction of electronic detonator systems for mine blasting, issues were raised about the application of MSHA regulations for shunting and circuit testing. The MSHA regulations for surface and underground mine blasting operations address the use of “electric” detonators. Although electronic detonators are initiated by an electric pulse or current, their design is unlike “electric” detonators. To resolve the issues of shunting and circuit testing with respect to MSHA regulations, a technical and field evaluation of electronic detonators was made and the results are presented.

Jan 1, 2005

By W. L. Fourney, D. C. Holloway, J. W. Dally

Introduction Improvements in the process of rock excavation by blasting involves better control of one or more phases of the fracture process immediately after detonating the ex- plosive charge. Total control of the process involves individual control of (1) The number of fracture planes. (2) The crack initiation sites. (3) The direction of crack propagation (usually radial). (4) The stress field driving the fracture front. Fracture plane control is usually accomplished today by using the smooth wall blasting method; however, investigations by the authors (1) indicate several areas where this method could be improved. These improvements include: a) generation of stress concentration factors at the location of the initiation sites; b) protection of the remaining region of the borehole wall to inhibit initiation of any cracks not associated with the fracture plane and fragmentation pattern; c) limit peak detonation pressures to avoid borehole crushing and maintain by stemming residual gas pressure in the bore- hole during the crack propagation period. This paper describes experiments con- ducted with a charge holding device fabricated from thin-wall steel tubing which was partially slit at fracture locations. The tube lined the bore-hole in laboratory tests to simulate smooth wall blasting. Results showed close control could be achieved relative to both the number and the location of the fracture initiation sites.

Jan 1, 1977