Search Documents

By David Green

Outokumpu introduced Flash Flotation in the early l 980's for the recovery of floatable material from grinding circuits. The devel­opment came as a result of surveys made in the company's own concentrators, initiated to find ways of improving recoveries with increasingly complex and lower grade feeds. Hydrocyclones make a separation on the basis of particle size and mass, resulting in the "over collection" of fine grained, high S.G. particles. Minerals such as pentlandite, galena and gold are easily caught in the circulating load around the mill until they are overground and rendered more difficult to collect. In the case of downstream flotation this may simply involve a reduction in the rate coefficient due to the finer sizes or, as is commonly experienced in gold operations, the mate­rial is slimed and coated onto non-floating gangue and is eventual­ly lost to tails. At the time of Outokumpu's plant surveys, it was a relatively common practice, particularly in Pb operations, to have a flotation section fed directly from the secondaiy mill discharge. This is called unit flotation and certainly provided an improvement but very high wear rates and frequent sanding out of the cells was com­mon. The development of the SkimAir® Flash Flotation cell by Outokumpu provided a subtle but quite dramatic departure from the unit cell approach. Now it was possible to feed cyclone under­flow into a special purpose-built flotation machine and recover a final grade concentrate from the grinding circuit (see Figure I). The cell was designed to handle the coarse circulating load, per­mitting the coarsest fractions to be short-circuited back to the mill and retain the floatable sizes for a nominal time of 30 seconds to several minutes. The short retention time was possible largely due to the relatively clean content of the cyclone underflow stream. This means that the fine gangue is not present except in small quan­tities and most of the fine to mid-size paiiicles are higher S.G. and more likely represent valuable mineral. This condition provides for very high rate coefficients. Typical operations would recover 40-60% of the valuable mineral in this fashion and improvements in recovery were typically from 2-5% for sulphide minerals to the 5-20% range for gold and silver.

Jan 1, 1998

"The paper treats the spatial aspect of mine sequence optimization. This aspect is revealed in the context of determination of the optimum number of cutbacks of an open pit mine. Cutback mining is a dominating method currently in base\precious metal mining and it is based on a pseudo-economic discretization of the pit space by using advanced pit design algorithms. The result of the implementation of such approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks for maximization of the project value. A mathematical solution of this problem is developed with the utilization of a combinatorial analysis. The solution provides a multi-variant investigation of the optimum mine sequence with the implementation of an author’s method for production scheduling optimization, which uses the Net Present Value as a criterion for assessing the economic efficiency of mine sequencing. A case study is provided for the conditions of a hypothetical open pit gold mine to illustrate the applicability of the approach. The results obtained reveal the complex nature of the variation of the Net Present Value as a function of the cutback geometry. INTRODUCTION The mine sequence optimization in open pit mining is a procedure that predetermines the efficiency of the production scheduling optimization. From a technological standpoint, the mine sequence optimization deals with two aspects – spatial and time. Each of them plays a tremendously important role in searching for the optimum solution of the open pit design problem. Original results on the time aspect of mine sequence optimization are published by Halatchev [2002]. They reveal a wide range of the Net Present Value (NPV) variation for a multi-variant arrangement of mine sequence over time and using a fixed geometry of the cutbacks, which determines the economic potential of a single open pit mine from a deterministic standpoint. The results show a range of NPV variation up to 30% depending on the stripping ratio of the mine. The effect of this variation is mainly due to the implementation of the mine planning principle of waste deferment in the scheduling optimization and using all theoretically possible variants of mine sequence arrangement by the inclusion of the bench sequences over the Life-Of-Mine (LOM) in the production process."

Jan 1, 2015

Little knowledge is available that considers the effects of continuous miner position on the possible respirable dust exposure of the remote mining machine operator. Such information could be very useful for increasing the awareness of the remote operator as to those parts of an extended cut that generate higher levels of respirable dust. This data could be used to develop guidelines for positioning the remote operator to reduce his potential exposure. This work details the effects of continuous miner position on dust levels measured on the machine and at the remote continuous miner operator location.

Jan 1, 1998

By R. R. Klimpel

Over the last six years, several new commercial families of sulfide mineral collectors have been developed. This paper summarizes some plant data and use experiences gained with each of these product families. The first is a series of products (F-series) based on a chelation mechanism of attachment. The second of these families is a series of products (S-series) based on an electrochemically controlled mechanism of attachment. The major advantage of the F-series collectors is the very high metal recovery capability in complex ores involving Au, Pt, Zn, Ni, and mixed Cu minerals. The major advantages of the S-series collectors are the very high pyrite rejection capability along with reduced lime requirements in Cu/Mo plants.

Jan 1, 1995

By Elias Apostolidis

Since 500 B.C. Mt. Penteli has been famous as white marble production site, which provided the birthstones for the construction of Athens Acropolis and Parthenon. The Aloula quarry belongs to ?Dionyssomarble S.A.?, a commercial and industrial marble company, which retreated after 1940. Disturbance in the site was minimal since then. In July of 1994 the reclamation started by a group of quarry workers from Paros, already familiar with traditional marble quarrying techniques, unchanged from antiquity to 1940. The project was complete in 1997. Our main objectives have been to show respect to the area and the art of people, to let nature guide our choices, to use only local stone as a construction means, to imitate the old construction rules and to turn the land use into amenity and civilization. Aloula quarry will become a site restored for amenity and civilisation, including ancient quarrying techniques. The restored quarry is already open to the public, though to a small number of visitors, and soon will become an amenity park and an open space museum of the ancient quarrying art.

Jan 1, 2002

By E. J. Dorward-King, R. J. Kadeg, S. Pavlou

Risk assessment, risk management, and engineering/economic feasibility analysis are presented as three effective, practical tools for decision making in the remediation of contaminated soils. Risk assessment is applied to evaluate the extent, magnitude and sources of contamination, to identify appropriate contaminants of concern (COCs). Risk management is then applied to identify the acceptable contaminant residual levels for the COCs. Finally, engineering/economic feasibility analysis is used to define the appropriate cost-effective remedial action and associated target contaminant action levels that will achieve the acceptable contaminant residual levels. A real site application of this decision making approach is presented. This site illustrates that through appropriate engineering, acceptable risk-based contaminant residual levels can be achieved with higher action levels.

Jan 1, 1992

By Arthur B. Cummins

It is appropriate to discuss diatomite at an AIME meeting in San Francisco. California has led the nation, and the world, in the production of diatomite products for more than 40 years. It appears that our State will maintain this position for a long time to come. Diatomite today ranks high in the list of California mineral commodities, with a total value since 1889 well in excess of $100 million. California's production has more than doubled since 1942. In 1959, the value of diatomite production in California is exceeded only by the following industrial mineral materials-borates, stone, sand and gravel and cement20,28. Also, not unimportant is the production of diatomite in each of our other Pacific Coast States, including Nevada. First, let us define diatomite. It is a sedimentary siliceous rock of organic origin, which consists mainly of the fossilized remains of diatoms. Diatoms are microscopic aquatic plants which have the capacity of precipitating silica bio-chemically so as to form a part of their organized structure. In the economic sense, we are not concerned with the numerous types of sedimentary materials which contain minor amounts of diatom residues, or with impure or highly indurated siliceous materials, which may have been formed from diatomite2. Diatomite (synonyms--diatomaceous earth, kieselgurO is a term generally restricted to material of such qualities as to be suitable for commercial uses. Diatomaceous silica is a designation which is best used to distinguish the basic component of diatomite, that is, the substance of the silica shell itself, and which is the major' constituent of beneficiated diatomite or processed diatomaceous products.

Jan 1, 1959

By Goran Mathisson

In several investigations the correlation has been studied between the fuel consumption and the reducibility of the charged material in the zone of indirect reduction in the blast furnace (1, 2, 3, 4, 5). It has been found that increased reducibility allows greater gas utilization which accordingly lowers the fuel consumption. In direct reduction units this relation has not yet been fully established partly owing to the lack of accurate test methods and experience with different materials as regards reducibility. However, since the production rate in a direct reduction unit is closely related to the time required to reach high degrees of reduction, the reducibility must be regarded as one of the most important properties of the material.

Jan 1, 1979

By A. Dale Wunderlich

With the price of precious metals at an 18-year low, every ounce of metal produced is important. The theft of metals from mining and refining sites can mean the diffrence between profit and loss for many mining companies. Low metal prices do not reduce the potential for the theft of precious metals. History has shown that the price of gold has little to do with the desire for employees to steal precious or base metals. There is actually evidence that the theft of precious metals increases when the price of this commodity goes down. Several of the major precious metal thefts in the past year took place at silver mines when the price of silver was less than 16 cents/g ($5/oz). How does the lowest gold price in 18 years affect the need for security at precious metals properties? There is no short answer to this question. One reason is because the exposure to theft of precious metals is unique to each property. This makes it important that each property be evaluated individually. More than 95% of all precious metals thefts can be attributed to those working at the mine site. So preventing employee theft is the primary concern. One consideration is the location of the property. Gold selling at any price is still an attractive commodity in countries where the employees are making between US$400 and US$600 a month. It is not uncommon for employees at mines in countries where low wages are the norm to consider the value of a gram or two of gold to be a significant amount of money. A gram or two of gold a day may not seem like much. But if 15 employees steal two grams a day, that equates to a significant amount of money during a year. The type of property where the precious metals product is being recovered is also important. For example, a property with a gravity circuit is more likely to suffer from the theft of gold product than a property where all gold is finely disseminated and the only gold seen in the ore body is through a microscope. Gravity circuits increase an operation's exposure to theft because the grinding circuit that is associated with a gravity circuit often becomes a giant concentrator. Areas such as the bottom of grinding-mill pump boxes, cyclone-feed-pump clean out traps and the sumps often become locations where precious metals concentrate (Figs. 1 and 2). Muck concentrations in these locations can be as high as 25% to 40% of gold or silver. Not long ago, muck was removed from a barren-solution sump at a Merrill Crowe circuit that had concentrated to more than 40% gold. At a milling site in the Pacific Rim, residents of the community adjacent to the mine learned about the value of the concentrates in the sump under the ball mill and committed an armed rob¬bery. While several of their co-conspirators held the em¬ployees at bay with machetes, the others emptied the contents of the sump into buckets and removed it from the site. Armed robbery is not as common as employee theft. However, while this article was being written, an armed robbery occurred at a gold property in Central America. Armed perpetrators took as hostages the night shift employees at a process plant and used cutting torches that were on site to cut into the high-security and gold-storage areas. The perpetrators then stole a company vehicle to remove the stolen gold buttons and sludge from the site. Unfortunately, this type of activity goes on regularly. But managements of most mining companies are reluctant to discuss theft scenarios. So information pertaining to the theft of precious metals seldom becomes a newsworthy item. An audit conducted at a mine site with a gravity circuit recommended that the gravity recovery area be shut down until adequate protection could be provided. Although it was not connected with the audit, it was necessary to shut down the gravity area for a pro¬longed period because of problems with the gravity table. In the two months that followed, gold production at the site increased by about 31 kg/month (1,000 oz/month). It is difficult to attribute all of this increase to the theft of concentrates. But there was a good chance that at least part of the increase was due to the fact that concentrates were being stolen from the gravity area.

Jan 1, 1998

By G Luxbacher

Computer simulation of mine ventilation systems is rapidly becoming an essential tool in mine planning and design. This paper examines the utilization of ventilation simulation techniques to evaluate the number, shape, size and layout of mine entries in a typical coal mining system. Since the mains and sub-mains serve mainly for transportation and ventilation and the ventilation system is critically important to the health and safety of the workers, there exists a great need for optimal designs in this area. Evaluation criteria, could include, among others, minimization of power costs, shaft requirements and leakage. Constraints of this optimization problem include health and safety regulations and production and mine infrastructure requirements.

Jan 1, 1977

By J. Y. Kim

Lead ions originating from galena during processing of complex sulphide ores migrate to "cover" the surface of sphalerite and iron sulphide mineral particles, and cause poor selectivity in differential flotation. Generally in sulphide ore processing, the lead-activated minerals float in the Cu/Pb rougher circuit. Subsequently, surface lead complicates the zinc flotation circuit by lowering the concentrate grade due to the co-flotation of lead-activated iron sulphide minerals. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zn and Pb-Zn ores is discussed. Plant and laboratory test data are interpreted by determining the surface composition of individual grains of sphalerite and iron sulphide particles using two surface analytical techniques, Laser Ionization Mass Spectrometer (LIMS) and Time of Flight-Secondary Ion Mass Spectrometer (TOF-SIMS). Cationic and anionic species on the surface were analyzed to elucidate the phenomena.

Jan 1, 1995

By G. G. Marino

Little comprehensive information has been reported on the behavior of room-and-pillar mines. The objective of this paper is to present case data on mine failures in the Illinois basin for use in practice. Presented are results of an ongoing study and details on the site characteristics of cases where sags have developed on the surface. Site data are reported to show the geologic, mining, and sag conditions that existed. Sags mainly develop from pillar, floor, or pillar-floor failure. The character of the sags depends upon the type of mine failure as well as the overburden response.

Jan 1, 1989

By Len H. Steele

To date VMD have designed, built and supplied nine autoclaves to various mining companies in Canada, the US, and Papua New Guinea. Initially, completely fabricated and lead lined units were shipped. The logistics of Placer Dome's Porgera PNG Project necessitated fabricating and lead lining each autoclave in five sections for transportation to site, each piece weighing approximately 30.5 tonnes. Support equipment such as turning rolls, automatic and manual welding machines had to be set up on site to facilitate assembly of these units which was a challenge in planning. This on site erection programme was completed in three months.

Jan 1, 1992

By John T. Atkins

Utah International's Shirley Basin Mine is located in the Southeastern High Plains of Wyoming at an elevation of about 7,100 feet. The Shirley Basin area is a gently rolling semi-arid land. The uranium ore zone occurs at depths ranging from 270 to 350 feet below the surface. Overburden consists of poorly consolidated sandstones, siltstones, and clays. Underground mining was begun in 1960. Conditions were made difficult by high rates of water inflow and ground support problems. The development of a solution mining I or in-situ leaching technique allowed underground operation to be abandoned in 1964. Solution mining provided limited production from 1963 to July 1970. In January, 1969, large scale development of open-pit mining was begun. A 1,200 ton per day mill went "on stream" in March, 1971.

Jan 1, 1973

By Clinton Strachan, Rob Dorey

10.1 INTRODUCTION This chapter presents considerations which should be applied to heap leach pad site selection, site evaluation, and design, relative to the geotechnics of the site and ore. 10.1.1 General Guidelines are presented covering the topics encountered in design and construction of heap leach faci1ities. Because geotechnical characteristics vary from site to site, not all geotechnical topics associated with a specific heap leach facility are presented, and there may be exceptions to some of these guidelines. The general features of a heap leach facility (from Chapter 1) to be discussed in this chapter are: • Leach pad (including leach pad foundation and liner); • Heap; • Solution storage faci1ities (for pregnant and barren process solutions) ; and • Solution collection facilities (which collect and convey solutions in the heap and convey them to solution storage facilities). These general features are illustrated in Figure 10.1. Liners for these facilities are discussed in Chapter 11. Solution application systems and the sizing aspects of solution storage facilities are discussed in Chapters 6, 7, and 12. The general features listed above are constructed with and overlie naturally occurring materials (such as ore, borrow soils, and subsurface soils and rock). These natural materials are relied upon to perform in an acceptable manner as a component of the leach facility (such as the liner, drain material, and foundation).

Jan 1, 1988

By Ben W. Burdett

The operation of an electrolytic refining tank house is an art as well as a science. If the electro-refining industry is to progress, a better understanding of the refining process is necessary. This would help to reduce the amount of training necessary to produce competent tank house operators who, in turn, would be able to increase both quantity and quality of the tank house product. To aid in understanding this process, quantitative relationships between the critical tank house variables must be established. The inherent major contributor to inefficiency in most tank houses is short circuits. By quantifying the effect of short circuits on each of the other variables in the system, as well as their effect on over- all system performance, better decisions regarding manpower allocation can be made. Current distribution under short circuit conditions, which has always been somewhat of a mystery, can be studied in detail. The relative importance of electrolyte balance, proper anode-cathode spacing, low contact resistance at points of electrical connection, and other system variables can be determined, With a better understanding of these variables, the steps necessary to increase current efficiency are more easily defined. Relationships between most of these variables are described in qualitative terms in the literature, but quantitative relationships between tank house variables have never been established. A realistic mathematical model of the tank house could be used to test the effect of variations in a single variable on other variables in the system, and thus define the quantitative relationships between tank house variables. It is not the purpose of this paper to establish these relationships, but to describe a recently developed model that can assist in their establishment. A computer program implementing this model has been applied to examine the effect of short circuits on overall current distribution. Some of the results are given here as examples of the utility of this program.

Jan 1, 1973

By H. Weber

This paper is in three parts. Part I discusses the various types of cement clinker coolers now in full-scale operation. Part II is a detailed study of the criteria for selection of the type of cement clinker cooler best suited for a given installation. Part III covers a number of cooling problems and their solutions in some of the metals industries. The large and world-wide problem of cement clinker cooling has motivated much study and development and the coverage here of this work is somewhat detailed. In contrast the cooling problems of the metals industries are quite varied between industries and often quite different from plant to plant in the same industry because of basic differences in the requirements of the particular material being processed. Therefore the coverage of metals industries coolers is somewhat more general. It is believed that all of the technology covered here may be of interest to those working with the problems of cooling hot materials.

Jan 1, 1980

By G. H. Matthes

Many mines, in particular coal mines, use inclines or slopes as an access to seam or seamlike deposits which outcrop at or close to the surface. In general, from the surface or from a certain depth, inclines or slopes follow the dip of the deposit with length up to 30,000 feet and by that going under an overburden cover of several thousand feet. The common outbye transport system for mine products is the conveyor. Material and men to be transported down into the mine are handled by rope driven systems when the angle of inclination exceeds the employment of locomotive traction. The transport volume can be sizeable and reach 200 to 300 tons of material and 500 men to be handled daily in a medium size coal mine with a production of 10,000 tons ROM.

Jan 1, 1986

By D. Castillo

The effectiveness of a flotation column is due principally to the addition of wash water to the froth phase. The wash water flow rate can be significant, especially so for systems yielding a high weight recovery of fine solids, e.g. zinc sulfide flotation. Therefore, it is critical to recognize and assess the impact of the water addition upon upstream separation stages. This paper examines column flotation circuit configurations using data from a portable 2 t/day pilot plant. The objective is to provide an improved basis for column design, either as a retrofit or as part of a new circuit.

Jan 1, 1990

By G. L. Mowrey

A new coal interface detection (CID) method is under investigation by the U.S. Bureau of Mines. This novel concept is based on utilizing a passive infrared system (FIR) to measure temperature changes associated with the cutting of coal and adjacent strata. For this method to work successfully, a definite mechanical/hardness contrast must exist between coal and rock. Advantages include that FIR responds instantaneously at the coal-rock interface and it is minimally affected by dust and/or water sprays. Based on preliminary tests, results indicate that the PIR method can be applied successfully in mines having a hard immediate roof.

Jan 1, 1990