Search Documents

By James P. Dorian

Like Russia and Ukraine, Kazakhstan is one of a few former Soviet republics well-endowed in mineral and energy resources (Fig. 1). Kazakhstan is the second largest newly independent Commonwealth state. It possesses major fuel and power centers, including 20 electric power facilities that operate on the more than 300 kt (330,000 st) of coal extracted daily. These power stations supply Central Asia, the Urals and Western Siberia with much needed electricity. Kazakhstan plays a critical role in Central Asia as it serves as both the regions' economic and political hubs. While Kazakhstan already contains a robust and diversified minerals industry, the government is actively pursuing foreign investment to boost production capacity and improve efficiencies in operations. A primary objective of the Kazak government is the expansion of metal processing facilities to improve the country's long-term export potential. Since 1991, international mining companies have found the investment climate of Kazakhstan relatively favorable. This is due to tremendous efforts by government officials to create sufficient investment legislation and a national minerals policy, while eliminating bureaucratic bottlenecks common to most other former Soviet republics.

Jan 1, 1993

By Kirk Carlton

The Athabasca tar sands of Alberta are an increasingly important source of crude oil for the North American continent. Published figures indicate estimates of recoverable resources in the tar sands at some 300 billion barrels of synthetic crude of which some 86 billion barrels can be recovered by surface mining techniques. At the present time, two commercial plants are in operation, Great Canadian Oil Sands Limited and Syncrude Canada Ltd. Their present combined capacity is approximately 150,000 barrels per day. Some of the factors which will make this oil expensive will be noted here. The location of the present producing plants is 500 kilometres north of Edmonton at an elevation of approximately 320 metres. Recorded temperatures range from +38 to -55 degrees Celsius. Wind velocities are not high but the chill factor with even a slight breeze and minus 40 degrees is very uncomfortable.

Jan 1, 1979

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

This paper presents the results of an investigation into the effect of pore pressure regime on the factor of safety (FS) and the anticipated critical failure mechanism for a fly ash storage facility. In this study, pore pressure measurements from standpipe piezometers and pore pressure estimated from seepage analysis were used for a comparison of the estimated FS for a fly ash slope. This comparison was applied for static and seismic scenarios. To account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation, a probabilistic analysis was performed. The slope stability analysis was conducted in 2D and 3D, adopting the limit equilibrium analysis approach, and a finite element seepage analysis. The results suggest consistency of failure surfaces for 2D and 3D and an increase in FS values of 5 percent for the 3D approach, limitations of standpipe piezometers. The study demonstrated the sensitivity of the FS value, and the implication of adopting representative material properties, and water table levels, especially in cases where limited data are available, and assumptions need to be made to assess the long-term stability of a fly ash dam facility.

Aug 1, 2024

By M. Solomon

Crushers are designed and manufactured to survive the severe duty of mining environments worldwide. Under these conditions the crusher performance and availability is one of the critical factors in the mine?s production and profitability. Traditionally the development of these machines tends to be experience-based, incremental improvements in design due to challenges of different applications, duty, or manufacturing. In order to better serve the mining industry a new approach was taken to the design of primary crushers. This approach was to focus on safety and maintenance activities. The result of this effort is a new generation of gyratory crushers that can be serviced from above. Using the features of this new generation of crushers to their fullest extent crushing installations have improved safety, reduced design and construction costs, and lowered maintenance requirements. This presentation explores the benefits of two crusher installations utilizing top service crushers.

Jan 1, 2010

By C. S. Vender

Knife River Coal Mining Company's Beulah Mine is a multiple seam lignite operation located in western North Dakota. The mine began production in 1963 with annual production at 450,000 metric ton and now produces 2.2 mm ton. As development progresses, operations have advanced into more complex geologic areas. Various techniques have been analyzed to maximize coal recovery in a cost effective manner. Additional studies are on-going to determine what changes will be implemented as we encounter deep wet sands in the reserve area.

Jan 1, 1991

By Elnaz Saminfar, Jae Bateman, Eric Westergren, Mark Trim

This paper presents a case study of two major Australian infrastructure projects that used digital engineering to facilitate design delivery: WestConnex Project (Rozelle Interchange), and Sydney Metro West (Eastern Tunnelling Package). The paper presents project overviews and building information modeling (BIM) execution and focuses on modeling techniques, software utilization, data management strategies and how the digital models helped the design-build team mitigate impacts to schedule by identifying clashes between disciplines before the execution of work. Finally, it demonstrates the positive and transformative impact of digital engineering on the design and construction of large underground infrastructure projects and highlights its role in asset management throughout the project lifecycle.

Jun 23, 2024

By D. W. Rierson

Svedala has a ported kiln process, designed specifically for the direct reduction of pelletized or natural lump iron ores. The process is called ACCAR. This ported kiln technology has been coupled with Svedala's GRATE-KILN System, for iron ore pelletizing, into the GRATE-CAR System for the reduction of fine grained ore concentrates through the steps of agglomeration, induration and reduction in a single production line. Additional applications of the GRATE-CAR System include: the recovery, agglomeration and reduction of steelmill waste oxide fines and the use of minus 6mm size natural lump ores to produce a highly metallized pellet agglomerate. Svedala conducts tests to confirm certain operating parameters through process simulations of the GRATE-CAR process. These tests are conducted at Svedala's Process Research and Test Center, Oak Creek, Wisconsin. Svedala also assesses issues of process variables, heat transfer, equipment sizing, retention time and endothermic demand associated with iron ore reduction using natural gas or coal as the reductant. The purpose of this paper is to present the GRATE-CAR processing concepts, the commercial production line and the testing procedures associated with investigating potential raw materials.

Jan 1, 1997

By Eleanor Kentish, Nathan Bond, Edward Batty, Simon Webber, Alan Skarda

"Crossrail is Europe’s largest construction project — a new 100km rail route running through central London. A joint venture of BAM, Ferrovial and Kier (BFK) has constructed the tunnels and escalator shafts at the new Bond Street and Farringdon Stations. The recent trend in the UK industry towards sprayed secondary linings is driven by the potential for significant savings in cost and time. BFK is unique within Crossrail by constructing both sprayed and cast secondary linings. This paper presents a direct comparison between sprayed and traditional cast in situ secondary linings at Bond Street and Farringdon Crossrail Stations. An objective comparison is drawn between procurement and mobilisation periods, production rates, flexibility, tolerances and logistics in the tunnels. The technical challenges surrounding cast and sprayed secondary linings are explored, and recommendations are made of how each method could be improved for future use. INTRODUCTION It is well established that sprayed concrete offers a fast and effective method to seal the face of an excavation. In a relatively short space of time, sprayed concrete can be applied to an open face to support the short term ground loading on the tunnels during construction. Advances in sprayed concrete lining (SCL) technology — such as the use of wet mix processes, improved accelerators, fiber reinforcement, remotely controlled spraying robots, innovative surveying equipment and nozzleman competency schemes — have greatly increased the speed and safety of tunnel excavations using this technique. As a result, design engineers have become increasingly confident to use SCL primary linings as part of the permanent structural lining (Su 2014). Historically, long term ground and water pressure loads have been considered to be carried by the main structural or secondary lining, constructed using cast in situ concrete (Pickett 2014). However, the advances described above have made sprayed secondary linings a viable option, which has already been proven on the A3 Hindhead Tunnel (Arnold 2012). Sprayed concrete secondary linings offer potentially significant savings in cost and time during the construction process. The contractor does not need to procure a bespoke formwork system for each different sized tunnel — the SCL plant required is already on site for the primary lining. Each bay is sprayed with accelerated concrete, becoming self-supporting almost immediately — compared to moving and resetting the shutter, pumping concrete and waiting for it to cure. With sprayed concrete, working sequences and cross sections can easily be changed."

Jan 1, 2016

By C. J. Hunter

Prior to the commissioning of the Sansu Sulphide Treatment Plant (STP), Ashanti Goldfields' treatment facilities were capable of producing some 700 000 ounces of gold per annum. Ore sources were underground refractory sulphides, surface oxides and old tailings dams. In order to increase the mines production to 1 million ounces per annum and to accommodate the change in ore sources as surface mining moved into fresh sulphides, a part of the strategy adopted was -the construction of a new sulphide treatment plant with a capacity to mill 2.2 million tonnes per annum and produce 400 000 ounces of gold. The STP has been designed, built and commissioned. and has been in operation since February 1994. The Plant boasts the world's largest Bio-oxidation facility which is capable of treating 790 tonnes of sulphide concentrate per day at a grade of 11.4% sulphur and is currently undergoing an expansion to increase its capacity to 1050 tonnes per day. The following sections describe the reasons for selecting the BioX® Process, the plant design, the commissioning experience and the plant performance to date.

Jan 1, 1996

By Jennifer King, Julius Strid, Steve Brandon

The Upper Hidden Basin Diversion (UHBD) tunnel was driven approximately 1.2 miles by the drill-and-blast method primarily through massive granite bedrock geology for the Kodiak Electric Association, Inc. (KEA) in Kodiak, Alaska. The tunnel was driven from both portals with a constant 11-ft straight-leg horseshoe cross-section. The design and construction of the tunnel was driven by logistics and weather conditions due to its remote location and the rugged terrain of the project setting. This paper will discuss the successful completion of a challenging project over a ve-year period from preliminary planning through the design and construction phases.

Jun 23, 2024

By Jodi Banta

In an effort to reverse the trend of declining enrollments to mining engineering programs that began in 2015, the University of Arizona has implemented a number of interventions over the past five years, including ramping up its pre-college mining education and outreach, and undertaking several enrollment research projects. This article is the second of two installments to discuss the results of our latest study. The first part can be found in the September 2025 issue of Mining Engineering magazine. To better understand mining’s competitive position, the School of Mining Engineering and Mineral Resources conducted a comprehensive study to determine: 1. How prospective college students, parents and educators perceive the industry, related careers and the mining engineering degree. 2. Factors affecting students’ choices of degrees and career plans. 3. The roles parents and educators play and how they influence students.

Nov 1, 2025

By H. S. Puttanna

Bound water plays an important role in the processing and utilization of numerous materials and mineral processing systems. The fundamental nature of this near surface bound (vicinal) water is yet to be understood in its complete detail. The objective of this paper is to use dielectric measurements to characterize the bound water near hydrophobic and hydrophilic oxide surfaces. It is anticipated that a combination of dielectric property measurements and characteristic relaxation times will allow for more effective analysis of the interfacial water.

Jan 1, 1992

By Paulo Roberto Pereira

This paper is motivated by the belief that increasing drilling and blasting costs will not necessarily bring about better digging or crushing productivity. As a matter of fact it can be counter productive as the ensuing discussion will show. In the two case studies presented herein when powder factor increased, productivity at a rope shovel and at a primary crusher decreased. Experience has shown that equipment (shovel and primary crusher) productivity increases as the powder factor increases and concurrently operating costs decrease. This is illustrated by Figure 1where the graph shows (assuming drilling costs constant) that for increases in powder factor initially operating costs might fall till a certain point and then they start to go up again. By the same token we need to understand what is the behavior of the operation’s productivity. It seems intuitive productivity goes up for increases in powder factor but when an operation reaches the point of minimum operating cost one could say that productivity reached its maximum. For continuing increases in powder factor can productivity still go up or does it go down? This paper presents two examples where the productivities of a surface coal mine and of a quarry are reduced for increases in powder factor. This indicates that these two operations could be operating to the right of their minimum operating costs and maximum productivity and therefore wasting precious drilling and blasting dollars and resources. Moreover, their productivity is following the red dotted line in Figure 1 and the question becomes can they follow the blue dotted line for increased drilling and blasting costs? The industry owes to itself to determine this minimum operating cost point and what can be done in case that the productivity goes down afterwards despite an increase in drilling and blasting costs. In other words, utilize your drilling and blasting resources correctly. In the two examples that follow single explosive loading strategies make powder factor a valid means of comparing the results of productivity as a function of powder factor. Also, external factors such as equipment operator influence are eliminated due to the long time span considered in the analysis

Jan 1, 2005

By Russell L. Cook

Stringent environmental regulations, which have limited the use of sludge ponds, coupled with the economic incentive to clean more 'coal or to add fine coal cleaning additions to existing preparation plants have increased the use of static thickeners in preparation plants. The Lamella Gravity Settler, sometimes de signated Lamella Thickener, is a shallow depth sedimentation device which has been applied in a variety of industrial process and wastewater control projects in place of the conventional raked thickeners. This paper presents the theory and design of the La-mella Thickener, as well as describing the operating results from several full scale installations in a variety of Appalachian preparation plants.

Jan 1, 1977

By Cameron Dunn, Callum Fryer, Carmen Hu, Craig Sewell, Peter Stakne, Andrew Raine

The Woodsmith Project is located in north-eastern England within the North York Moors National Park. The strata contains the world’s largest known high-grade Polyhalite resource of around 2.66 billion tonnes. The Project was initiated by York Potash Limited (YPL), a subsidiary of Sirius Minerals plc., but in March 2020, a takeover was completed by Anglo American, one of the largest mining companies in the world. Polyhalite is an evaporite mineral and contains essential nutrients required for plant growth. The Polyhalite will be extracted via two deep mine shafts and transported underground from the mine site to a Materials Handling Facility on a Mineral Transport System (MTS), which comprises a high-capacity conveyor belt system located within a 4.9 m ID tunnel. In 2018, STRABAG were awarded with the design and construction of the MTS tunnel and associated infrastructure, including the high-capacity conveyor system. The scope of work consists of 300 m of open cut, 100 m SCL tunnel, 36.5 km TBM drive (originally anticipated as three separate TBM drives) along with a network of underground caverns at the Woodsmith Mine. The construction of two 380 m deep intermediate access shafts was later awarded as Amendments to the Contract. The tunnel is constructed using a Herrenknecht Single Shield TBM. As a result of how the various elements of the project have developed over time, the first TBM drive has been extended to ~29 km making it the worlds longest single heading TBM Tunnel when complete. The option of completing the entire tunnel length with a single heading TBM drive is currently being assessed by Anglo American and STRABAG. This unprecedented tunnel length requires two intermediate shafts to provide essential access and services, the first intermediate shaft is at Lockwood beck (LWB) and the second is at Ladycross (LDX). The LWB shaft has been constructed utilising the innovative Blind Boring technique never used before in the UK. This paper will explain the methodology and technical risk management associated with this technique. The authors believe that the collaborative approach between all contract partners is and continues to be the important contributor for the success of this project.

Jun 13, 2023

By M. Xing, S. Usman, K. Awuah-Offei

"While mines generally focus on achieving operational efficiency, creating shared value for all stakeholders is also a management goal. This includes taking a holistic view of their supply chains and increasing local participation. This paper examines the role of supply chain management in mine management; in particular the effect of a strong local supply chain on regional economic impacts. Using input-output analysis, the impact of a local supply chain on a mining sector’s regional economic impact is examined by increasing local sourcing (increasing local purchase percentage -- LPP) for 10 key commodities. An approach, based on multipliers and excess local capacity is used to identify key commodities. The impacts examined are sales, employment, labor income, and value added. The work is illustrated with stone mining and quarrying in Missouri. Ten percent increases in LPP of the key commodities, in this example, result in $4.1 million additional impact on the Missouri economy. This work can provide insight on how to better create shared value for all stakeholders. INTRODUCTION Little research has been published on improving mine supply chain management (SCM) to enhance regional economic impacts. Although some extensive academic research has explored the importance of an industries’ supply chain, not much is known about how a locally-based supply chain increases shared value in the resource sector. Across industries, traditional SCM is getting more and more complex. This is true of the mining sector as well. However, this increased sophistication is not directed towards increasing shared value for all stakeholders, particularly, the local communities. Further research is required to develop new SCM strategies that enhance local participation. One major point of difference between this work and traditional supply chain management is the inclusion of stakeholders’ shared value as a goal in SCM. Creating shared value has become a business goal in recent years (Porter and Kramer, 2011). The authors use input-output analysis (Leeuw, 2012) to evaluate the regional economic impacts of supply chain decisions, which is not part of traditional SCM. Although input-output analysis has been applied to SCM for decades, most of the research uses input-output analysis as a tool to advance an industries’ own operational efficiency (Accenture, 2014)."

Jan 1, 2015

By Diler Katircioglu-Bayel

The effects of the operating parameters of media filling ratio, solid mass fraction, grinding media size and grinding time on the stirred media milling of talc were studied. The findings were assessed based on the product particle size (d50, d10), surface area (Sw) and energy consumption (Em). Furthermore, after determining the optimum grinding conditions, Box-Behnken statistical design was used to determine the effect of parameter interactions on the d50 size. The media filling ratio significantly affects d50 size decrease compared with solid mass fraction and grinding time. The minimum d50 size was also achieved under optimum grinding conditions.

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. Saki, J. F. Brune, J. W. Grubb

"Researchers at the Colorado School of Mines have studied the influence of headgate side ventilation controls near the longwall start-up room on the formation of explosive gas zones (EGZs) in underground coal longwall bleeder ventilated gobs. In a project funded by the National Institute for Occupational Safety and Health (NIOSH) researchers developed a Computational Fluid Dynamics (CFD) model to study the formation of methane-air mixtures in the gob, start-up room, and bleeder entries. The relative change in size and location of EGZs are examined in response to ventilation controls in the headgate side bleeder entries near the start-up room. Modeling suggests that adjustments to the ventilation controls can be made to minimize the size of the EGZ. However the EGZ may form in or around active working areas regardless of the ventilation control settings. Research found regulators on the crosscuts into start-up room and first entry inby can force air into to crosscuts outby the start-up room causing more air to flow through the gob. INTRODUCTION Underground longwall mine ventilation systems may operate with either a bleeder ventilated gob or a progressively sealed gob. Bleeder ventilated gobs must meet the standards for safe operation of the bleeder system by examining bleeder system effectiveness. As defined in the United States Mine Safety and Health Administration (MSHA) Program Policy Letter (PPL) No. P13-V-12 (MSHA 2013), the pillared area or gob is “any area where a reduction in pillar size has occurred during retreat mining” and includes the “caved and broken material, the interstices within the caved material, and the open spaces surrounding the caved material.” The PPL further states that the intended purpose of ventilating the gob is “to protect active workings from the hazards of methane accumulations …” The requirements for operating a bleeder system as stated in The United States Code of Federal Regulations (CFR 2013) Title 30 §75.334(b) is to pass ventilation air though the gob “and to continuously dilute and move methane-air mixtures [from the gob] away from active workings and into a return air course …” where the concentration cannot exceed 2 percent methane (CFR 30 § 75.323). Further clarification of the bleeder system as described in the PPL states the following: “A bleeder system includes the area from which pillars are wholly or partially recovered, bleeder entries, bleeder connectors, and all associated ventilation control devices that control the air movement through the area. Bleeder entries are air courses designed and maintained as part of the bleeder system.”"

Jan 1, 2015

By Mark C. Holton

The mining industry has recently been. - experiencing a difficult period. Escalating costs, lower grades and deeper level mining, are a few of .the reasons' why interactive graphics or CADD (computer aided design and draughting) systems are increasingly being used. CADD systems which support powerful and flexible mining applications have great potential for making all forms of mining more efficient and effective. There are many application programs which address almost every aspect of mining. Most of these programs originated to satisfy a particular need. Graphics and other features were added until they, reached a point where they were commercially viable as a mining package. Because of their evolution these packages, lack many CADD-type features. Today there are powerful personal computers (PC's) and engineering workstations running the best CADD systems available. These systems, support hundreds of applications in almost every discipline. Mining was until recently not well supported by interactive graphics vendors because of the highly variable nature of mining and the lack of common standards. Users of CADD systems have experienced the benefits of CADD and come to expect similar features from graphic mining packages. Several developers of mining packagers have either attempted to include some CADD features or make their packages compatible with one or other CADD system. Mining can benefit greatly From a combination of interactive graphics (or CADD) and the right mining application software.

Jan 1, 1989

By Kenneth L. Schellie

In preplanning the reclamation of a pit or quarry the geology of the site is the name of the game! The planner must know the parameters of the deposit, the quantity and kind of earth materials to be removed, and the amount and nature of the materials to be left behind or wasted as the result of processing the marketable product. With many states and most local jurisdictions requiring reclamation plans prior to the issuance of mining permits, the need for accurate and complete data concerning the geology of the site becomes increasingly important. The producer need only know that marketable materials are available in sufficient quantity to make the mining operation economically feasible-the planner, in order that the land may be reshaped for a useful purpose, must have reasonably precise information as to the dimensions and configurations of the pit or quarry following extraction and the amount and type of materials available on the site (or in some cases offsite as well). Therefore the geology of the site is of major significance in determining the land forms and use capabilities of the property upon completion of the mining process.

Jan 1, 1974