Search Documents

By B. A. Kuyper

The Cove gold-silver deposit is located 50 km southwest of Battle Mountain, Nevada and 1.5 km northeast of the McCoy Mine. Total proven and probable reserves are 48.7 Mt (53.7 Mst) with an average grade of 1.85 g/t (0.054 oz/st) Au and 87.1 g/t (2.54 oz/st) Ag. Mineralization is hosted by Triassic carbonate and siliciclastic rocks in two separate orebodies. Oxide ore consists of disseminated gold and silver in clay-altered, manganese-flooded limestone. Sulfide ore is dominated by pyrite-sphalerite-galena veins in siliciclastic rocks and sandy dolomite. Gold and silver occur in the native state, associated with the base metal sulfides. Mineralization is interpreted to be the distal expression of a porphyry system. The McCoy gold (copper) deposit is interpreted to be the proximal expression of the same system.

Jan 1, 1991

By K. P. Bingham

Lime is one of the largest volume chemicals produced in the United States. In 1979 approximately 21 million tons were produced. Lime is, in fact, second only to sulfuric acid as the largest volume basic chemical produced. Lime, also known as quick lime (calcium oxide) and hydrate lime (calcium hydroxide), is the principle alkali used in a multitude of industrial processes. In addition to its use as a principle industrial alkali, lime has experienced dramatic growth in four general market areas during the past 30 years. These four areas are: 1. Water Treatment - Lime is used extensively in treating and purifying water for industrial and potable use, Although significant tonnage is shipped to this market of municipal and industrial water treatment plants, the end-users are widely spread geographically and individual shipments are relatively low tonnage. Lime, which is nonhazardous, can safely be shipped by truck or rail to these small end-users. 2. Municipal and Industrial Waste Treatment - Environmental agencies at all government levels,

Jan 1, 1980

By K. N. Han, H. C. Cho, R. Kim

"As an extension of the work on the effect of OH- on various cations in hydrometallurgical systems, the effect of Cl-, Br-, I- and CN- on cations such as Ag+, Cd2+, Hg2+, Cu+, Cu2+, Co2+, Zn2+, Pb2+ and Sn2+ has been examined in detail. The Newton-Raphson technique has been used to determine the amounts of various metal species as a function of the concentration of anions. Some practical implications of various metal complexes in metal separation and removal from solutions have been examined and discussed.IntroductionUnderstanding the role of anions in hydrometallurgical processes often determines the success of an operation. The successful choice of concentration and type of anions not only leads to an effective extraction and removal of metals (Esmaeili et al., 2005; Brbooti et al., 2011; Wei et al., 2005; Jeppesen et al., 2009; Al-Tarazi et al., 2004), but also to assisting effective separation of various metals, whether it is a solvent extraction, ion exchange operation or even a simple precipitation (Farha et al., 2011; Sevenich and Fritz, 1983; Rashid, 1974).This paper continues the discussion of the role of anions in hydrometallurgical systems beyond the role of OH-, which was the topic of a previous paper (Kim et al., 2014). Table 1 lists various anions that are frequently used in conjunction with metal ions to be selectively separated or precipitated. As seen in the table, many anions are used frequently in hydrometallurgical practices. Some of the more frequently used anions include OH-, SO4 2- and CO3 2-. The halogen elements, Cl-, Br- and I- , as well as CN-, are also used in hydrometallurgical applications, especially in relation to noble metal recoveries (Meng and Han, 1994; Zhang et al., 1996; Sun et al., 1996; Starovoytov et al., 2007)."

Jan 1, 2015

By Wallace W. Key

Problems of marketing industrial minerals to chemical manufacturers are manifold. In addition to the difficulty of establishing demarcation lines between "crude" and "processed" industrial (nonmetallic) minerals, and "industrial mineral compounds" further uncertainty exists because some chemical manufacturers do not talk the same language as the industrial mineral producer. For example, paint technologists use "rutile" and "anatase" to describe highly refined chemical compounds. The earth scientists use these terms to describe naturally occurring minerals. Further, marketing research problems are intensified because of the overlapping data of the Standard Industrial Classifications (SIC) groups, and the inexactness of "Chemical Industry," "Chemical and Allied Products Industries," and "Chemical Process Industries," which are widely variable in meaning but are often used interchangeably. Bureau of Mines information Circular 8244, "Minerals for Chemical Manufacturing," was the out¬growth of an attempt to unravel some of the problems caused by overlap of statistical data compared with actual industry practices. Using this study as a base, specific industrial mineral applications of some important sub-industry groups were analyzed for the; California chemical industry. Differences between local and national practices were compared. Practices usually differed, depending on cost and availability of alternate minerals, climate, idiosyncrasies, local regulations, and other conditions. Bureau of Mines Information Circular 8260, "Mineral Fillers for the California Pesticides Industry," is the first such analysis of, a sub-industry group. Other such studies are underway. Obtaining national data is easy, but to be able to compile meaningful information which can be revealed on a regional and State basis generally is difficult and often impossible. This paper will briefly emphasize some of the industrial mineral problems encountered, and bring out the needs and benefits being derived through the continued cooperation of authoritative officials concerned with supply and consumption of industrial minerals in government and industry.

Jan 1, 1965

By W. Haupt, M. Thormé, H. J. Ertle, K. Reim

Though Germany has a very old mining history, her experience in uranium mining only started in the late sixties. Today in the Federal Republic of Germany (FRG) there are only 5 small mines in the exploration stage, namely Menzenschwand and Müllenbach in the Black Forest and Mähring, Popenreuth and GroBschloppen in northern Bavaria. In all these exploration mines much development is required to define shape and size of ore bodies. Mining engineers, government authorities and environmentalists alike are very much concerned about environmental safeguards and protection of mine workers against radon and its daughter products. Miners are affected by internal and external radioactive exposure. In general the external [f3]- and [µ] -exposures can be considered as small in comparison to the internal exposure and are therefore not discussed in this paper. The internal exposure is caused by the inhalation of radon and its daughter products and is relevant to the lung as the critical organ. The nobelgas radon is inert and does not from compounds with other elements easily. Contrary to the physical half-life of 3,8 days the biological half-life of radon is only 10 to 20 minutes. During the rentention time in the body only approximately 1 % of the long-lived decay products are retained in the system (SCHOGER, 1976). In this connection is it important that the radon resorption as well as the radon secretion varies individually and depends to a large extent on the age of the person (SCHOGER, 1960). RENOUX et al. (1978) have determined that the greatest part of the a(-activity in the air is attached to aerosoles with a diameter of 0,4/14. The radiation exposure of the lung by radon is negligible if compared with the exposure by short-lived decay products. For this reason one has introduced the concept of the potential [o](-energy (P) of the short-lived radon decay products, which means the total [ct]-energy, which is produced when an atom decays in the decay-series down to the long-lived lead-210. [ ] The unity of the potential [o]-energy concentration in the SI-system is 1 j/m3 air. In radiation protection however a specific unit is used namely the working level (WL): [ ] The WL-unit, though internationally recognised has not been introduced officially in Germany. Because of the large amount of tunneling still to be done in the FRG, the various mines departments responsible for safety and health in mining ask searching questions such as: - What are the laws governing radon emanation in tunneling? - Can workers be adeguately protected against radiation hazards? - How should one drive through high grade uranium ore? - What happens if the ventilation system breaks down?

Jan 1, 1981

By Moreno Pescara, Luca Soldo, Piergiorgio Grasso

"Risk management in tunneling is more important today than it was a few years ago, considering increasing demands for safety and environmental and socio-economic sustainability, which are now required by citizens, owners, lenders, and insurers. Moreover, our current risk management philosophy should not only address risk avoidance and mitigation, but should also be used as a means of value creation, benefiting the overall project. Given the strategic implications of risk management, the authors intend to present, in this paper, a comprehensive overview of references and experiences from current practice—e.g., what is missing or weak, as well as possible or necessary developments that can have a key role in implementing effective risk management, particularly for a project’s design and construction phases. Therefore, as God has set some things in broad daylight; as he has given us some certain knowledge, though limited to a few things so, in the greatest part of our concernments, he has afforded us only the twilight, as I may so say, of probability (John Locke) PREFACE Many large-scale engineering and construction projects suffer millions of dollars in cost overruns, delays in design and construction, and operability troubles once finally completed (Edward W. Merrow, 2011). The undesired effects of these problems can become disastrous for large-scale megaprojects (those that typically cost US$1 billion or more), particularly considering that these are increasingly used as the preferred delivery model for infrastructure (Bent Flyvbjerg, 2014), often in public-private partnerships (PPPs). McKinsey G.I. (2015) has estimated that bridges and tunnels average 35% in cost overruns, and roads 20%. Some of the values published by Flyvbjerg (ibidem, 2014) for projects with relevant underground elements are the highest, with cost overruns from 60% to 300%. The analysis of 32 other case histories (from 1994 to 2010) given by Hartmut, R. (2011, IMIA Annual Conference, Amsterdam) indicates an average increase of costs around $55 million, with a 20-month average delay."

Jan 1, 2016

By Paul C. Lingo

Two recent antitrust cases, coming from widely separated areas, different industries and involving wholly different facts were decided by the Supreme Court on June 7, 1965. The decisions in these two cases may well prove to be the most important and far-reaching decisions in the field of labor law that have been handed down in the last 24 years. These cases, although quite dissimilar factually, had one common element. In both, the gravamen of the antitrust violation was bottomed on the terms of labor agreements negotiated by a multiemployer group. These cases are usually referred to as Pennington1 and Jewel Teat. Since a number.-of references will be made to the antitrust laws, it may be well to state briefly the applicable portions. Section I of the Sherman Antitrust Act makes "every contract, combination in the form of trust or otherwise, or conspiracy, in restraint of trade or commerce among the several states, or with foreign nations, is declared to be illegal...". Section 2 imposes criminal sanctions against "Every person who shall monopolize, or attempt to monopolize, or combine or conspire with any other person or persons, to monopolize any part of the trade or commerce among the several states...". Under Section 4 of the Clayton Act a person who sustains damages as a result of a violation of the antitrust laws is entitled to recover treble damages plus costs.

Jan 1, 1965

By R. H. Hanewald

The processing of EAF baghouse dusts from both the specialty steel industry and low alloy producers will be reviewed. In addition, the INMETCO process has been modified so as to recover nickel, chromium and iron from many other waste materials such as pickling solutions or filter cakes, spent nickel and chromium plating baths, carbon refractories from pickling tanks, and super alloy wastes including baghouse bags. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high temperature metals recovery. This, along with the details of INMETCO's BDAT Test Program and results performed to pre-agreed standards with the EPA will be discussed.

Jan 1, 1992

By Michael J. Martinson

A powerful methane explosion in the mid-shaft pump station of a main service and ventilation shaft killed several persons on the station; more workers were killed when a mancage travelling down the shaft fell to the shaft bottom under a pile of broken concrete slabs from a brattice wall destroyed by the explosion venting into the shaft and a tangled mass of twisted steelwork from the equipped compartment. The newly-commissioned shaft serves a recent extension of an established mine on the Orange Free State (OFS) goldfield in South Africa. After outlining the circumstances in which the paper was written, and reviewing the nature and extent of the methane hazard in OFS mines, the paper describes the physical layout of the shaft and summarises evidence given by witnesses at the official inquiry concerning events prior to the explosion. No attempt is made to apportion blame for the incident.

Jan 1, 1989

By S. Shankar

The phenomenon of re-entrainment is seen in many environments, such as sand dune formation, soil erosion, fugitive dust emission, spread of radio-nuclides from accidents involving nuclear weapons, etc. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of on-going research in the Respirable Dust Center on the prediction of ambient dust concentrations in mine atmospheres (Ramani, 1983) to identify the contribution of dust re-entrainment to the spatial and temporal concentration in mine airways and included wind tunnel and in-mine studies. A set of seven experiments was performed in the Lake Lynn Laboratory Mine of the U.S. Bureau of Mines under controlled conditions. Two types of source coal dust, anthracite and bituminous, were subjected to airflow with a range of air velocities and walking by two different walkers. Six sets of instruments were used along the test section for sampling the airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/s. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (i.e., total) airborne dust increased to 0.17 mg/m' (standard deviation = 0.10 mg/m') from an initial value of 0.02 mg/m'. The action of personnel walking, however, caused higher amounts of re-entrainment. Average concentration of respirable and total dust at the center of the mine airway increased to values of 0.28 mg/m' (standard deviation = 0.12 mg/m3) and 1.53 mg/m3 (standard deviation = 1.0 mg/m3), from initial values of 0.03 mg/m3 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal dust bed. Depending on the level of activity and the amount of dust deposited in mine airways, re-entrainment may become an important source of airborne dust away from the point of actual mining.

Jan 1, 1994

By A. L. Mular

Se revisan brevemente varios procedimientos para el cálculo de coste de capital; no obstante, se discute en preferencia el método del factor estimado. Se proporciona una tabla de costes frente a los datos de parámetros de equipo, de donde los costes pueden ser adaptados a partir de los valores actuales de los índices de costes M&S para minería y molienda. Las ecuaciones de costes son utiles para preparar los programas de computador que realizan cálculos de coste de capital. Se ilustra la utilización del metodo del factor estimado.

Jan 1, 1982

By Lloyd W. Trevoy

Commercial production of heavy minerals from plant tailings streams is undergoing study by Syncrude Canada Lrd. When tar sand from an open pit mine is processed and up- graded to synthetic crude oil, heavy minerals can be recovered from the extraction circuit and can be upgraded to provide concentrates of zircon and titanium minerals. The titanium minerals concentrate consisting of a mixture of ilmenite, leucoxene and rutile, could be utilized as recovered or could be upgraded to synthetic rutile. With the construction of further synthetic crude oil plants in Western Canada a large reserve of heavy minerals will become available for utilization.

Jan 1, 1981

By Daniel E. Collins

Massive banded Fe-Zn-Cu-Pb sulfide deposits in the Bagdad are associated with metamorphosed eugeosynclinal mafic volcanic and intrusives rocks Precambrian age. The geologic environment is very similar to that of the Jerome-Prescott area which lies 70 km. east of Bagdad. Mining of massive sulfides deposits began in 1917 on the Copper King mine in spite of its early discovery and the discovery of the Old Dick mine in 1882. The first shipments of zinc ore from the Copper King were hand sorted and averaged 46.89% Zn, 5.7 oz. Ag, 3.58% Pb and 1.68% Cu. Oxidized copper was first produced from the Old Dick mine in 1943~ In all, five deposits of massive sulfide ores have been mined in the Bagdad for a total production of nearly 2 million tons with an average grade of 12.0% Zn and 3.6% Cu. The largest deposit, the Bruce mine is currently closed because reduced metal prices and has produced a total of 823,000 tons of Zn-Cu ore to date. Mining of massive sulfide ore in the Bagdad area is presently idle. However, the potential for locating yet undiscovered ore bodies is good. Exploration for new ore bodies is difficult at best due to the complex geologic history of the area, the small size of individual ore bodies and lack of understanding as to the formation of massive sulfide deposits. The purpose of this investigation was to obtain a better understanding of the host rock formations through detailed geologic mapping, petrography and chemical analysis.

Jan 1, 1977

By L. H. Munson, D. E. Hadlock, L. F. Munson, R. L. Gilchrist, P. D. Robinson

All uranium mills are required to perform sampling and analysis for radioactive particulates in their gaseous effluent streams and in the environment. Pacific Northwest Laboratory was requested by the U.S. Nuclear Regulatory Commission (NRC) to provide technical assistance to them for their Uranium Mill Health Physics Appraisal Program. In conducting appraisals, air sampling methods used at NRC-licensed mills were reviewed and several deficiencies noted. This paper includes only environmental and effluent particulate sampling although much of the information is applicable to both in-plant and environmental samples. First, the components of a proper sampling program are discussed: program objectives, program design, sampler design, analyses, quality assurance, and data handling. Then the specific deficiencies, or the "pitfalls" from the first 8 mill appraisals are discussed. The first consideration in establishing an air sampling program is defining the objectives of the program. What is air sampling suppose to accomplish? Many of the deficiencies we have observed have resulted because the desired objectives were not clearly established in the minds of the radiation safety staff. PROGRAM OBJECTIVES An environmental air sampling program ought to fulfill the following seven objectives. The first is to: 1) [demonstrate regulatory compliance]. Although a goal of most programs, regulatory compliance, is not well understood. One has not only to comply with the conditions of the source materials licensee, but one must also demonstrate compliance with 10CFR20 and 40CFR190. For example, 10CFR20.106 states: "A licensee shall not possess, use, or transfer licensed material so as to release to an unrestricted area radioactive material in concentrations which exceed the limits specified in Appendix B, Table II of this part .... For purposes of this section, concentrations may be averaged over a period not greater than one year." Even if a mill's license does not require sampling at the site boundary of maximum concentration, a sample may be necessary to demonstrate compliance with 10CFR20. Most mill personnel are painfully familiar with 40CFRl90.10, which states: "Operations.... shall be conducted in such a manner as to provide reasonable assurance that: (a) The annual dose equivalent does not exceed 25 millirems to the whole body.... of any member of the public as the result of exposures to planned discharges of radioactive materials, radon and its daughters excepted... from uranium fuel cycle operations..." This means a licensee's sampling program must give "reasonable assurance" that the member of the general public receiving in the most exposure gets no more than 25 millirems per year. The sampling program necessary to provide that assurance may or may not be a license requirement. However, merely meeting the license requirements and the explicit regulatory requirements does not necessariarly ensure an adequate effluent and environmental air sampling program. The second objective of the environmental air sampling program, is to 2) [identify the source(s) of contaminants]. This will include not only the routine program, but special sampling for verification of sources and nonsources. Only after sampling can a mill operator be assured that roof vents, laboratory hoods, and other localized ventilation systems are not making a significant contribution to environmental releases. An environmental sampling program should also allow the mill operator to fulfill the third objective, to 3) [estimate exposures]. Even before 40CFR190, a sampling program should have provided the mill operator with the information necessary to determine the dose to the "fence post" person, or at least to determine if doses were well below the 10CFR20 limits previously allowed. The program should 4) [detect and measure unplanned releases]. If there is a fire, a scrubber failure, or if a drum of yellowcake breaks open, measured releases will almost always be lower than conservative estimates. Whether or not a system to provide sampling during accidents is needed is almost always a cost-benefit decision. In general, uranium operations do not sample just in case an accident may occur. Yet they may decide on continuous air sampling in lieu of intermittant sampling partially because of the potential for accidents. Another objective of air sampling is 5) [to provide information on the effectiveness of control systems]. This is always a concern with new or modified equipment and may dictate sampling frequency in other situations as well. For instance, if a small leak in a bag filter cannot be detected by other means, then more frequent stack sampling may be indicated. A routine effluent and environmental monitoring program should also fulfill the sixth objective,

Jan 1, 1981

By A. Mertzanis

The way and methods used for the surface mining of bauxite until the end of the twentieth century in the area of Ghiona, resulted in a significant burden to the natural environment, especially in the cases where it covered extended parts of forests and forest areas as well as important geomorphological formations. The impacts from the surface mining of bauxite which in fact constitute the object of this study relate mainly to the interruption of the natural continuity of the land relief and the alteration of the natural geomorphological activities and are due to: a) the alternating excavations with fronts of great heights, b) the depositions of large volumes of waste materials which originate from the revealing of the ore and c) the dense road network constructed in order to get access to the mine locations.

Jan 1, 2006

By Muhammad I. Kabir

A new minitest of in situ uranium leaching processes at reservoir conditions is proposed. The test which consists of a single observation/ production well and two observation wells is designed to permit the evaluation of both restoration and leaching parameters. It is shown that by using a straight forward history matching procedure, sometimes called a type curve analysis, both the rate of leaching and the ultimate uranium recovery can be evaluated based on the results of the test. Type curves are presented for the case in which the reaction rate is kinetically controlled and there are no other minerals competing for oxidant. Other situations can be approached using the same techniques as those presented here.

Jan 1, 1981

By Irwan Halim, Stephane Polycarpe, Brian Hann

The Narragansett Bay Commission Phase III CSO Program includes construction of the 11,600-foot long, 30-foot ID, deep rock Pawtucket Tunnel in Rhode Island. This paper provides an overview of the Design Build Project features and highlight some of the important design considerations, features, and innovations, including geologic conditions and related TBM design, and deep shaft and tunnel segment designs. The paper provides the most recent updates on some of the project construction activities including TBM tunnel progress and retrieval schemes, tunnel pump station and deep vertical shaft liner installations, SEM construction, and microtunneling for the longest adit using Fiberglass Reinforced Polymer Mortar pipes.

Jun 23, 2024

By L. Cui

A new flotation collector, benzyl arsonic acid, was used for the flotation of ilmenite. ESCA, Auger spectroscopy, and chemical analysis were used to investigate the correlation between the variation in surface constituents and the flotation recovery of ilmenite. Experiments indicated that, as the ratio of surface Ti ions/surface Fe ions increases, flotation recovery increases. pH regulation with an inorganic acid was found to be effective in changing the ratio of surface ions, and, hence, the flotation recovery.

Jan 1, 1986

By Thomas O. Glover

History of Underground Coal Mining in Illinois The production of coal in Illinois using underground mining methods, commenced early in the 1800's; however, the first shaft entrance was not sunk until 1842. The shafts range in depth from 16 feet (4.9 m) in Peoria County to 1,001 feet (306 m) in Christian County. The earlier mines were smell, private operations that worked outcrops and shallow seams at less than 100 feet (30.5 m) in depth. By 1975, there were reported 4,076 abandoned underground coal mines in 70 Illinois counties (Nawrot, 1977). There were many more mines; however, only 4,076 underground mines have been documented. Small mining operations characterize the majority of the underground mines. There have been no significant multiple seam operations in Illinois. The most extensively mined seams were the number two, five, and six seams. Number two seam was worked in the early 1900's by 252 mines in the longwall mining region of northern Illinois (Nawrot, 1977). Available records for 2,054 abandoned mines identify 1,043 as shaft nines, 700 as slope mines, and 311 as drift mines. Some operators began reporting annually to the State Department of Labor in 1879 and by 1882 all mine operators were reporting. Annual reporting still continues to date. The information is compiled by the State Department of Panes and Minerals in their "Annual Coal Report." By the end of 1974 there were 800,000 acres (323,756 hectares) of abandoned underground coal mine workings (Smith-Stall, 1975)2 Copies of abandoned underground coal mine maps may be inspected by interested parties in the State Department of fines and Minerals office in Springfield, Illinois, or at the office of any county recorder for mines within their county. Copies of active underground coal mine maps may be inspected at a State mine rescue station near the mine site or at the county recorder's in the county in which the mine is located. Copies of active underground coal nine naps shall be open to the examination of all interested persons, but such examination shall be made only in the presence of the State mane inspector or the recorder. At the present time, the Department of Mines and Minerals has 1,746 maps of abandoned underground coal mines in its possession. These maps cover the majority of

Jan 1, 1977

By Jin Anshi, Wang Dai, Wang Zingshen

Both fire and gas problems in Fully Mechanized Sublevel Caving Coat Face are quite different from those in common fully mechanized coal face. Pouring N2into the goaf would be the best method to prevent fire in the goaf. In this paper how to determine parameters of pouring N2 is discussed. Comparing distributions of gases and temperature before pouring N2into the goaf with those after pouring N2 into the goaf, the effectivenesses of preventing the fire by pouring N2 into the goaf are testified. Some special gas problems appear in Fully Mechanized Sublevel Caving Coal Face, which are proved to be serious and interrelated with pouring N2 into goaf. Finally, a few methods adopted to deal with gas problems are described simply.

Jan 1, 1991