Search Documents

By Jerry C. Tien

The rare earth elements (REEs) are a group of 17 chemical (metallic) elements. REEs are used widely in high-technology, clean-energy products as well as weapon systems. China's dominant position as a producer of over 95% of the world REEs output and the world's increasing reliance on REE products have highlighted concerns about the future availability of rare earths in recent years. This paper briefly reviews the REEs world reserves, production, consumption, the impact of our heavy reliance on REEs products and China's changing policies on REE export on world supply chain.

Jan 1, 2013

By Tony Szwilski

A correlation between the rank, ash content and coal seam discontinuities and coal strength/stiffness is discussed. Rebound hammers were used to evaluate the strength properties of two coal seams. The coefficient of variability of the rebound tests are compared with those of laboratory compressive strength tests by other investigators.

Jan 1, 1985

By F. F. Peng

A unique collector dispersion techniques was developed and used to improve the flotation rate and recovery of coarser and ultrafine coal-rich particles in the froth flotation processes. In this novel collector dispersion method, the collector such as hydrocarbon-oil is gasified and transported by gas phase (air stream) into the pulp. In addition to the excellent mode of collector dispersion, the collector-encapsulated air bubbles are generated in the pulp. This approach alters the surface properties of air bubbles and provides the fast rate of flotation compared to that of direct liquid collector addition froth flotation. Using gasified kerosene as the collector, the effect of altering surface properties of bubbles on the recovery of larger and finer coal-rich particles of -1.7 mm (-12 mesh) and -600 µ m (-30 mesh) raw coal samples were studied. The Redstone seam coal obtained from Northern Central region of West Virginia was used in this work. The effect of particle size on oil-coated bubble flotation rate and recovery were also evaluated. The conventional froth flotation test with a liquid form of kerosene addition was also conducted for comparison purpose.

Jan 1, 1991

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By Joseph A. Whitchurch

The N20 to N25 Tunnel (basic) segment was the second tunnel contract awarded for construction by The PB/MK Team. This project embodied 3.9 km (2.4 miles) of tunnel and was located within the northwest quadrant of the 86.9 km (54 mile) long main collider ring. The contract required the excavation and initial support of a 54.3 m (178 vlf) deep ventilation shaft, a connecting horseshoe shaped Adit and TBM starter tunnel and 3,865 m (12,680 If) long main collider tunnel with a 4.3 m (14 ft) minimum finished diameter. This paper discusses the construction methods, equipment utilized and the production achieved in the construction of the ventilation shaft, connecting adits and the main collider tunnel.

Jan 1, 1995

By G. R. Hart

The expected 1990 Clean Air legislation is providing electric utilities with a series of challenges and decisions as the utilities prepare strategies to comply with the resulting regulations. This paper addresses the strategy development of a coal-based utility --the legislation, the process used, the fuel issues, the options available, and the decisions to be made.

Jan 1, 1991

By Milka Madahana, John Ekoru

Particulate matter is one of the leading pollutants in the mines and in the communities in the areas near or surrounding the mines. The availability of large Clinical and environmental data sets obtained from the mines has brought about the need to use better approaches to analyze the collected data. Prediction and control of particulate matter concentration in the mining environment is essential in minimizing air pollution and protecting the respiratory health of mine workers. The main objective of this research work is to analyze datasets obtained from a mining area using machine learning techniques which will then be followed by the real-time estimation of dust particulate in the mines. Datasets collected over 8 years in an hourly sampling rate from an open cast mine is cleaned and analyzed for trends and patterns. Artificial Neural Networks (ANNs), Support Vector Machines and decision trees techniques are applied to analyze and predict the particulate concentrate. The estimation of particulate concentration using Artificial Intelligence will significantly contribute toward the development of quantitative tools to be used in correlating of cause and effect of dust concentration in mines. The results obtained in this work will form a sub-unit of a respiratory health monitoring system for mine workers. The system is essential in the collection, analysis, and tracking of mine workers’ respiratory health, thus it forms part of an early intervention system for mine workers. From the existing theory, we expect the Artificial Neural Network will perform much better than previously used classical models.

Jun 25, 2023

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By A. Bruynesteyn

The results of a 2 phase evaluation program designed to determine the amenability of an oxide ore from the Butte, Montana mine of the Anaconda Company to a sulfuric acid leach is presented. In the phase 1 preliminary evaluation, using roll tests and percolation leaching in small columns, it is shown that the ore is highly extractable at low acid consumption ratios. In the phase 2 confirmatory tests in large columns on l-l.5 tons of material, the amenability of the ore to the leaching process is proven and pregnant solution grade profiles from planned commercial heaps established.

Jan 1, 1978

By A. Ghosh

Commonly used predictors of ground vibration from blasting, being linear in log-log plot, do not model the underlying physics of wave attenuation. Amplitude of the wave decays with distance due to geometrical spreading and inelastic attenuation producing a nonlinear carve in log-log scale. The nolinear decay of seismic waves has also been observed from non-explosive sources, such as, pile driving, drop hammer, traffic, etc. The improved predictors, by explicitly taking these two mechanisms into consideration, model the data trend extremely well at all distance ranges. Actual field data from different studies have been used to validate the improved models.

Jan 1, 1991

By D. -P. Georgescu

A native sulfur mineralization associated with pyrite and iron oxides containing 20% iron was quarried in Calimani Mountains, Oriental Carpathians. The wastes resulted from this exploitation activity, with a volume of 33 millions m3, were stored in four dumps while the wastes resulted from ore processing using flotation and the subsequent treatment were disposed of in a settlement pond. The investigations carried out in the entire mining area focused on the following two aspects: - the impact of environmental factors mainly on the hydrographic network; - the characterization all pollution sources, namely dumps, leachates and the quarry and the assessment of acidic drainage generation. The total sulfur content of the excavated ore was 3.8% while in dumps it ranged between 0.54 and 1.06%. Analysis of samples collected along the hydrographic network, draining the mining area, resulted in pH values ranging between 1.7 and 2.83 as well as high concentration of iron (4525 mg/L to 1.6 mg/L), copper (1.87 mg/L to 0.04 mg/L) and zinc (13.13 mg/L to 0.3 mg/L). Samples from the quarry, the dumps and the tailings pond were analyzed in order to deter-mine: - the maximum potential acidity (MPA); - the acid neutralization capacity (ANC); - the net acid production potential (NAPP).

Jan 1, 2005

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By Harvey P. Knudsen

This paper illustrates the application of geostatistics to a roll front type uranium deposit located in Wyoming. The steps involved in calculation of experimental variograms, variogram modeling and verification of the resulting models are described in detail. The resulting spherical variogram models for grade thickness and thickness show strong geometrical anisotropies. The major axis of anisotropy for both variables is approximately parallel to the axis of the roll front and the minor axis perpendicular to the roll. This model confirms the technique of drilling "fences" across the roll front, where the drilling is much closer together than the fences along the roll.

Jan 1, 1978

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By Jie Long, Zijie Liu, Pu Liu, Bo Li, Menghua Li, Qiang Wu

During coal mine operations, roadways may be located close to faults. When designing these roadways, it is important to determine the width of the rock mass between a roadway and a fault area to prevent water inrush. In this paper, the Xintian Coal Mine in the northern Guizhou Province of China is selected as a typical case. Through numerical simulation based on orthogonal tests, range analysis, and multiple linear regression (MLR) analysis, the process of water inrush from faults in excavation roadways is studied. The results show that the influencing factors of the safe width of a rock mass preventing water inrush (RMPWI) can be ranked according to the degree of influence from large to small as follows: the hydraulic pressure of the fault, the surrounding rock grade, the overburden depth of the roadway, the cross-section height, and the dip angle of the fault. Among them, the dip angle of the fault, the cross-section height, and the surrounding rock grade are negatively correlated with the safe width, while hydraulic pressure of fault and overburden depth of roadway are positively correlated with safety width. The predicted value for the safe width based on MLR is greater than the measured value of the width of the RMPWI when water inrush occurs, but less than the calculated value based on the empirical formula in the standard, which proves the accuracy and practicability of the prediction method. This research provides a certain basis and reference for the prevention and control of water inrushes in mines.

Jul 5, 2023

By R. Bhaskar

The objective of the project was to optimize the ventilation parameters of a continuous miner underboom scrubber to further control. the amount of airborne dust discharged during mining, to further reduce the exposure of face personnel for an exhaust brattice ventilation system, and avoid recirculation of contaminants at the face. This research was performed in an underground coal mine in Utah. The tasks included preliminary face ventilation evaluation and optimization of the scrubber system to eliminate recirculation of the scrubber discharge air. Airflow tests were conducted on the currently used dust control system and the modified scrubber system. Tracer gas tests were performed to evaluate face ventilation effectiveness. Confirmatory tests of the scrubber system under actual operating conditions, modifications to the scrubber system, and a comparative evaluation of the scrubber system vs. the existing system were performed. This paper presents the results of the airflow pattern tests and the respirable dust levels in the modified scrubber system and the existing system. The optimized face ventilation parameters and the developed operating guidelines may provide the benefits of dust reduction, better face ventilation, and improved visibility.

Jan 1, 1994

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study was to investigate the influence of amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and organic acids (citric, malic, tartaric, fumaric, oxalic, succinic and ascorbic acid) on gold extraction from silicate ore. Use of amino acids to extract gold was preferred compared with organic acids due to the presence of carboxylic group and amine groups in amino acids. Among the assessed amino acids, aspartic acid and glutamic acid had higher capacities to extract gold due to their structures, which lacked aromatic rings and long side chains. Organic acids could also extract gold. In particular, oxalic and succinic acids had the greatest capacity to extract gold versus the other tested organic acids. Moreover, aspartic acid had a greater capacity to extract gold from ores than the same concentration of succinic acid. We confirmed the aspartic acid and succinic acid functional groups by Fourier transform infrared spectroscopy. The findings revealed that aspartic acid had a greater capacity to extract gold than succinic acid due to the presence of both amine and carboxylic groups (succinic acid contained only a carboxylic group). The optimal gold:aspartic acid molar ratio was 1:6 and low concentrations of aspartic acid extracted 35–42%of gold from silicate ore within 15 days. This can be used as an alternative to traditional methods for extracting gold from ore; it is non-toxic to human health and environmentally friendly.

Aug 10, 2021

By Mamookho Elizabeth Makhatha, Mbal Henock‑Michel Mwanat, Kubangala Brest Kasongo, Ntumba Edward Malenga

This study investigated the operating parameters that affect the kinetic dissolution of copper and cobalt from sulfidic ores. The sulfuric acid concentration, temperature, sodium chloride concentration, particle size range, and leaching time were selected to deduce the kinetic mechanism of the leaching reaction. Other parameters, such as a stirring speed of 250 rpm and the percentage solid 10% w/v, remained constant. The results reveal that an increase in acid concentration enhances the leaching rate of copper and cobalt. Copper and cobalt dissolution was positively affected by the addition of sodium chloride. The highest leaching rates of copper and cobalt were 24.71% and 15.65%, respectively. The chemical control and diffusion control by shrinking core models are well fitted as the kinetic models representing the dissolution of the minerals. The respective activation energies for copper and cobalt dissolution of 10.92 and 31.023 kJ mol− 1 for the chemical control and 18.83 and 37.28 kJ mol− 1 for diffusion reaction control were established from temperature-based experiments.

Aug 26, 2022

By K. S. Gritton

The U.S. Bureau of Mines has investigated methods for extracting metals from a variety of arsenic-containing smelter flue dusts. One proposed flowsheet includes a sulfuric acid leach, a cooling step to precipitate hydrated copper sulfate, and a reduction-precipitation of As2O3. Arsenic extractions greater than 90 pct were achieved, while copper extraction ranged from 50 to 85 pct under the conditions examined. Copper was removed from the leach solutions by crystallization followed by SO2 precipitation of arsenic which resulted in a 98 to 99.9 pct As2O3 product. Other metals, such as lead and zinc, were concentrated in the leach residue or in other byproduct streams for recovery of their valuable metal contents.

Jan 1, 1990

By Adrian Molinari

A radioisotope probe (Minexan 202) capable of simultaneously analyzing a mineral slurry for five elements and pulp density has been developed by Outokumpu Oy, Finland. The probe is designed to operate immersed directly in a process stream, or it can be equipped with a flow cell through which passes a continuous sample of the main stream. A minicomputer (PDPII) is used to control the probes and calculate the assay data. This paper describes the probe as applied to slurry analysis and compares it to the conventional x-ray on-stream analyzer (Courier 300).

Jan 1, 1977