Search Documents

By D. L. Boreck

With increasing land development, the potential of fatalities from abandoned mine shafts increases. To minimize potential liability, shaft closure should be a critical part of mined land reclamation. The Bureau of Mines is conducting research into using lightweight foam concrete in sealing abandoned coal mine shafts. A demonstration seal consisted of a 3m thick foam concrete plug to provide lateral stability inside the shaft. A high density concrete cap provided load-bearing capacity for a 100-year service life. The USBM has also completed research into changes in foam concrete when it is pumped or dropped from different heights. It is concluded from the research that foam concrete can undergo significant air loss with pumping or dropping. This foretells significant changes in the characteristics of the concrete as well as an increase in the weight and cost of the in-place concrete seal. When using foam concrete to seal abandoned mine shafts, care must be taken to minimize air loss during placement.

Jan 1, 1994

By D. S. Yantek, R. J. Matetic, A. K. Smith, E. D. Thimons, J. Srednicki

In a 2007 report to the U.S. Congress, the Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) stated that built-in-place refuge alternatives (BIP RAs) provide significant advantages over mobile refuge alternatives. At present, the requirement to locate refuge alternatives within 305 m (1,000 ft) of working faces makes BIP RAs impractical in most coal mines. BIP RAs would be practical if three issues are addressed: (1) allowing BIP RAs to be located at greater distances from the working face, (2) developing a reliable process for the design and approval of BIP RA stoppings that meet the 0.1-MPa (15-psi) design criteria, and (3) developing systems that reliably deliver breathable air to the refuge alternative. In 2015, NIOSH OMSHR conducted a study of these three issues and issued a report. In the report, justification was provided for allowing the placement of BIP RAs at greater distances from the working face than the currently mandated 305 m (1,000 ft), guidelines were developed that could be used by industry when submitting BIP RA stopping design applications for approval which are patterned after the Mine Safety and Health Administration guidelines for coal mine seal design applications, and insights were provided into options for providing a reliable supply of clean, breathable air to BIP RAs. This paper presents a summary of the study’s findings and also addresses issues discovered during the building and designing of a BIP RA that OMSHR researchers constructed in NIOSH’s Experimental Coal Mine in Pittsburgh to research the testing and improving of BIP RAs. These issues include several issues related to the delivery, distribution and exhaust of ventilation air to the BIP RA and some general construction issues that require further investigation.

Jan 1, 2016

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with mediumsized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in the present study: a 15.2-cm (6-in.)-wide shelf; a 7.6-cm (3-in.)-wide shelf; and a 7.6-cm (3-in.)-wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1 and 1:1 were evaluated for the 15.2-cm (6-in.)-wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. IntroductionSurface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1 percent of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples).• 5.8 percent of rotary drillers were overexposed to respirable silica dust (nine out of 155 samples).• 7.3 percent of drill helpers were overexposed to respirable silica dust (three out of 41 samples).• 7.5 percent of blasters/shotfirers were overexposed to respirable silica dust (three out of 40 samples)."

Jan 5, 2018

By W. W. Mason

The United States began exporting coal in the late 1800'5, at first in very small quantities to Canada and beginning in 1897 and 1896, to the east coast of South America. Shipments to European countries began on a very limited basis in 1902 and these shipments increased gradually until World War One when shipments overseas increased from the 8 million tons per year level to 22 million tons. After the war exports dropped as fast as they had increased and, with the exception of exports to Canada, remained at very low levels until just after World War 11 when the United States again emerged as a major coal exporter. World War II left the coal industries of Europe in ruin. As the United States was the only country able to supply the large quantities of coal at reasonable prices needed for reconstruction of the European economy, the U. S. coal exports overseas expanded rapidly to 42.5 million tons in 1947. Additionally, we shipped 25 -2 million tons of coal to Canada In that year for a total export of 68.7 million tons. Unfortunately, that level was not reached again until 1957 when exports reached an all-time high of 76 .4 million tons- -a high I might add that has not been reached since.

Jan 1, 1980

By Robert E. Kirby

The potash mine and refinery of AMAX Chemical Corporation is located 26 miles east of Carlsbad on the north end of the potash producing areas. This property was developed between 1949-1952 and production of muriate began in August 1952. Two shafts, located 400 feet apart, were sunk to the ore zone 900 feet below the surface. A 15-foot diameter ore hoisting shaft equipped with a 1000-ton ore pocket, crusher and automatic skip loading equipment plus a 20-foot diameter service shaft with a curtain wall for exhausting air were provided. Sylvinite production to date has been from the first ore zone, stratigraphically, the lowest of ten identified mineralized zones in the salt section. This first ore zone has been the top producer of Muriate of Potash over the years. In our area we do have some very marginal mineralization in the third ore zone some 35 feet above the first. We have not mined from this seam as yet but we are investigating the economics very closely with access slopes and an experimental mining panel. Our ore seam is generally flat lying but does have local gentle rolling with grades from 2% to 5%. The mine was designed and developed from the beginning with conventional mining practices and rail haulage from the mining section to the ore pocket. As mining progressed in the early years, production increased from less than one million tons annually to a maximum of 3,935,000 tons in 1964. Efficiency also kept pace with the increasing production and continually improved until the efficiency of the production crews reached an average of 100.3 tons per manshift in 1964.

Jan 1, 1974

By Kevin J. Ashley

Coal is deposited at a mine site in several thin seams which outcrop in rolling hills and dip at about 8° to the northeast. The deposit is located in the northeast area of the State of New Mexico in the Southwest of the United States. A drilling program was undertaken and was quite irregular. Not all of the seams appear in all of the drill holes. Some of the holes did not go deep enough, while others were drilled below the outcrop of some seams. Occasionally a seam would pinch out and not be seen in a drill hole. Also, the outcrops of the seams are buried in many places by several feet of alluvium. All of these factors make correlation of the seams between drill holes difficult. The drawing of cross sections in three directions and at many locations across the mining area have been necessary to assure the accuracy of the input data.

Jan 1, 1982

By J. R. R. Bowling, A. McFadden, M. Francoeur

The abstract discusses the increasing use of extensive duct-fan systems in underground hard-rock mine development. It highlights the challenges of designing these systems, particularly the risk of partial vacuum and the need for careful booster fan positioning. The paper explores factors influencing the design of these systems, including component limitations, operational wear margins, and power constraints. It also defines the concept of partial vacuum and its impact on ventilation ducts. The authors propose an algorithmic approach for specifying the location and blade pitch of in-line booster fans to prevent system failure.

Mar 17, 2022

By D. Donison

The practice of blasthole mining is typically applied in competent ground conditions, primarily because of the open stope dimensions. At Magma Copper -Superior Mine, a field pilot project was completed examining a variation of blasthole mining in poor ground conditions. The results were very encouraging not only from a technical viewpoint, but also productivity viewpoints. This paper describes the pilot project and the resulting implications.

Jan 1, 1994

By Deepak Malhotra

Is operator training necessary for optimization of flotation plants? The answer is obvious-Yes. The author suggests a three-phase program for operators when new plants are built or new crews are hired in existing operations. Case examples are discussed to illustrate the benefits of operator training.

Jan 1, 1999

By Jean E. Tilden

An investigation of several trace elements distributed among sulfide minerals from deposits located in the southeastern United States was conducted. The deposits investigated are distributed within both the Blue Ridge Province and the Piedmont Province, which are contiguous geographic provinces. Twenty five deposits were examined;' eleven in the Blue Ridge Province and fourteen in the Piedmont Province. Figure 1 shows the locations of deposits investigated. In the deposits investigated, the mineral phases examined were pyrite, pyrrhotite, chalcopyrite, and sphalerite. These phases were chosen because of their relatively widespread occurrence, although no pyrrhotite was seen in the Piedmont Province. A total of 116 polished surfaces of ores were prepared, and mineral phases were collected from these surfaces for analysis. Samples were analyzed for cobalt, nickel, manganese, lead, tin, chromium, molybdenum, and gold. A total of 372 analyses were made. Trace elements were determined by atomic absorption spectrophotometry following standard procedures. In this study, trace elements are defined as those elements which are present in the mineral but which do not affect the chemical formula for that mineral. Lead is considered as a trace element only in ores where little or no lead sulfide could be identified as a distinct mineral phase.

Jan 1, 1972

By Grant R. Brown

The objective of this paper is to describe a study sponsored by the U.S. Department of Energy during which a model was developed to optimize haulback mining procedures in single and multiple seam contour mines, The study objective was to achieve financial- based productivity increases approaching twenty percent. This paper reviews the results of the first year's Phase I activities, which include four main tasks: formulate a methodology that can be used to select equipment and mining procedures that result in optimal performance in a particular haulback mining situation; conduct field studies of representative single and multiple seam mines to obtain quantitative background information for development of the formulated methodology: develop the methodology into a useful design tool for mine operators; and prepare plans for field tests to evaluate the effectiveness of the developed tool.

Jan 1, 1981

By D. A. Norrgran

The term "secondary recovery" has recently brought on a new meaning in view of the depletion of natural resources, energy conservation, plant optimization, and the environmental consciousness that has led to hazardous waste management, recycling, and secondary processing. Many secondary recovery processes are being developed applying mineral processing technology. Gravity separation, magnetic separation, and flotation have all emerged as implicit methods for recovering residual values from various process streams and hazardous constituents from waste streams. Recently, a technique for concentrating metallics has been successfully reintroduced. Although the concept of the eddy-current separator was developed over a century ago, (Patent 400317 issued to Thomas Edison on March 26, 1889) it was not until this last decade that it gained prominent acceptance. The evolution of permanent magnets has provided a cost effective alternative for the generation of high intensity magnetic fields. High energy permanent magnets have substantially reduced the capital and operating costs over the electromagnetic circuits employed in antecedent eddy-current separators. Specifically, in recent years, the strength of permanent magnets has increased several fold with neodymiun-boron-iron rare earth magnets now providing an energy product of 35 million gauss-oersted. Figure 1 shows the evolution in the strength of permanent magnets. The development of these rare earth magnets has led to the design of circuits possessing a magnetic force an order of magnitude greater than that of conventional permanent magnetic circuits.

Jan 1, 1991

By W. M. Middleton

The exploiting of geothermal steam is a new endeavor in this country and is for that matter a very new science in the world. With the majority of steam wells in the world having been drilled during the last twelve years relatively little experience and knowledge has been gained that can guide us as compared to the techniques the oil and gas producers have developed for their use. We few technical personnel associated with the field find it a continuous challenge to understand and explain what effects or causes the various unusual phenomenon experienced. We have had unending discussions attempting to formulate pet theories which we can use as guides. We know, so the geologists tell us, that the source of the heat is from the hot magmatic core of the earth. Theory has it that the magma is cooling off and that hot gases are given off as this magma cools and shrinks. In volcanic' areas along fault lines where the magma reaches closer to the surface than in other areas, there is a higher concentration of gas evolution; consequently, geyser or geothermal areas are developed. As these hot gases rise toward the surface they encounter various minerals, including overlying bodies of water. It is into these underground lakes that our wells are penetrating. As the heat enters these lakes it spreads out by conduction, convection and water migration. We can strike this hot water over quite large areas in many of the geothermal fields. At present there is one anomaly to this in the United States as there is in Italy where our wells do not penetrate a hot water lake. This is at The Big Geysers in California. Here superheated steam is produced with a heat content, so high that it could not have been boiled off of a fresh water pool. This puzzled us until last year when a well was completed into a large body of brine in the Imperial Valley. This brine exists at close to 500°F and at a hydrostatic pressure sufficient to preclude any boiling. It is now believed by some of us that a similar pool of brine must exist below The Big Geysers area, from which the steam is emanating. If there is such a brine pool, it offers a plausible explanation of the high-heat content, for brine boils at a higher temperature than fresh water. I am now beginning to think that a similar brine pool may exist under all the geothermal basins for if it is under two of them, it is highly probable that it is under the others. The partial understanding of what we are drilling toward, and formulating a theory to explain its behavior helps guide us in our steam well drilling.

Jan 1, 1963

By R. A. Winters

At the operations level, productivity is a principle key to profitability. If you are competing with other mines that are paying roughly the same wage rate and the same prices for capital, materials, and energy, the only way your profit can be greater is by producing more output per unit of input. Mines with higher productivity have higher profit margins. Higher profit margins lead to greater operating cash flow, and cash flow is what distinguishes a dog from a cash cow. The turnaround in U.S. metals during the 1980s was in large part due to incredible improvements in productivity. According to statistics compiled by Kaufmann, 1991, labor productivity, measured as tonnes of primary production/manhour, increased 64% in steel, 94% in copper, 75% in lead, 143% in zinc, 132% in molybdenum, and 75% in gold. These improvements were hard won. However, with most modernization programs now complete, measuring and monitoring productivity becomes even more important as producers strive to maintain the gains they have achieved.

Jan 1, 1993

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the roof bolter canopy air curtain (CAC) designed by the U.S. National Institute for Occupational Safety and Health (NIOSH) has gone through many iterations, demonstrating successful dust control performance under controlled laboratory conditions. J.H. Fletcher & Co., an original equipment manufacturer of mining equipment, further developed the concept by incorporating it into the design of its roof bolting machines. In the present work, laboratory testing was conducted, showing dust control efficiencies ranging from 17.2 to 24.5 percent. Subsequent computational fluid dynamics (CFD) analysis revealed limitations in the design, and a potential improvement was analyzed and recommended. As a result, a new CAC design is being developed, incorporating the results of the testing and CFD analysis.IntroductionExposure to respirable coal mine dust can cause coal workers’ pneumo-coniosis (CWP), also known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is to eliminate exposure to respirable coal mine dust and crystalline silica, or quartz. The occupational exposure limit on a Mining Research Establishment (MRE) basis for respirable coal mine dust had been 2 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities. Under recently enacted legislation, this standard was changed in August 2016 to 1.5 mg/m3 for a full working shift (The Office of the Federal Register, 30 CFR 70.100, 2015). When respirable quartz is present, the mine must maintain its average concentration at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percentage of quartz present (The Office of the Federal Register, 30 CFR 70.101, 2015).The sources of exposure to respirable coal mine dust for roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind — in the return air — of the continuous miner (Good-man and Organiscak, 2003). Recent studies have demonstrated that vacu-um dust collection systems are effective in capturing bolter-generated dust if maintained and operated correctly and if proper face ventilation techniques are used. However, most expo-sure to respirable coal mine dust for a roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner (Potts, Reed and Colinet, 2011; Colinet, Reed and Potts, 2013). Because of this higher exposure downwind of the continuous miner, the roof bolter is often limited to working downwind of the miner only once during a production shift."

Jan 1, 2017

By Ralph Musick, Brian Briggs

The U1h Shaft Project is a design/build subcontract to construct one 6.1 meter(m) (20 feet [ft.]) finished diameter shaft to a depth of 321.6 meters (m) (1055 ft.) at the Nevada Test Site (NTS). Atkinson Construction was subcontracted by Bechtel Nevada(BN) to construct the U1h Shaft for the Department of Energy (DOE). The project consists of furnishing and installing the sinking plant, construction of the 321.6 m(1055 ft.) of concrete lined shaft, development of a shaft station at a depth of 297.5 m(976 ft.), and construction of a loading pocket at the station. The outfitting of the shaft and installation of a new hoist may be incorporated into the project at a later date. This paper will describe the design phase, the excavation and lining operation, shaft station construction and the contractual challenges encountered on this project.

Jan 1, 2001

By John W. Trammell

The White Pine Mine is situated in Ontonagon County, approximately six miles south of Lake Superior, in the Upper Peninsula of Michigan (Figs. 1 and 2). The ore body mined by White Pine Copper Company occurs in the lower - most 20 to 25 feet of the Nonesuch formation, a series of middle - to upper Keweenawan shales, siltstones, and sandstones. This paper elaborates on the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the ore body.

Jan 1, 1964

By Mollie Hunt, William Riley, Russ Downer, Kate Willa Brown Requist, Víctor O. Tenorio, Geoffrey Gill

One of the first activities after returning to the Moon will be finding sources of water and materials for the construction of human settlements and other infrastructure. There is evidence of the existence of deposits in the bottom of craters at the South Polar region and in flat areas around. Based on geological data from the Moon, a block model representing a deposit or icy regolith has been defined in the vicinities of Shackleton Crater, with unique characteristics of shape, thickness, and water contents. A mine plan utilizing surface mine modeling software for ore extraction from an open pit- type of excavation to a delivery point near a water processing facility is proposed, with monthly, quarterly, and yearly schedules. Production results, dashboard charts and progress of the topographic changes are also presented.

Feb 1, 2024

By J. DuCarme, A. Smith, M. Reyes

"A magnetic proximity detection system is mounted on a mobile mining machine to prevent underground workers from being pinned or struck by machine motion. The system generates magnetic fields around the machine to determine safe working distances. The minerworn component measures the magnetic field in order to approximate location. Large masses of steel, such as those from mining equipment, can alter the magnetic field distribution. This affects the locational accuracy of the system, thus adversely impacting worker safety. To examine this problem, U.S. National Institute for Occupational Safety and Health researchers developed a method and test system to study the influence of a steel mass on the magnetic field distribution. The results show that a steel plate can strengthen the magnetic field perpendicular to the generator by up to 40 percent. Furthermore, they show that the degree of the influence on the field distribution is a function of distance. The results from this study can be used to further develop and improve the performance and reliability of electromagnetic proximity detection systems used in underground mining applications.IntroductionOn average, 250 miners are injured every year, and 43 miners were reported to be killed by striking or pinning accidents involving continuous mining machines in the United States between 1984 and 2015, according to the U.S. Mine Safety and Health Administration (MSHA, 2015). Continuous mining machines are large mobile machines used to mechanically cut coal in underground mines. These machines weigh approximately 60 t (132,000 lb) each. Although modern continuous mining machines can be remotely controlled, operators still need to be close to the machine primarily because of the low visibility and wide blind spots of the underground working environment.The MSHA promulgated a final regulation in 2015 that requires the use of proximity detection systems on all continuous mining machines except fullface machines. MSHA has approved five such systems to be intrinsically safe for use in underground coal mines: (1) Strata Worldwide’s HazardAvert System, (2) Frederick Mining’s Model 200 HazardAvert Detection System, (3) Nautilus International’s Coal-Buddy System, (4) Matrix Design Group’s M3- 1000/Joy Global SmartZone Gen 1 and (5) Matrix Design Group’s IntelliZone/ Joy Global SmartZone Gen 2."

Jan 6, 2018

By R. H. Kuhlman

The purpose of this paper is to describe the roles of cement and concrete in construction in general and, more specifically, as construction materials of the Southeast. For purpose of this discussion, the Southeast will include the geographic area composed. of the following 13 states: Alabama, Arkansas, Florida, Georgia, Kentucky, Louisiana, Mississippi, North Carolina, South Carolina, Tennessee, Texas, Virginia and West Virginia. In one sense, cement by itself is not a construction material. It is a finely ground manufactured mineral product, usually gray in color. Cement is mixed with water and sand, gravel, crushed stone, or other aggregate to form concrete, the rock-like substance that is the most widely used construction material in the world. Because cement is seldom used by itself for construction but is usually a component of concrete, there is no such thing. as a "cement" sidewalk, a "cement" highway, or "cement" building. Neither is "portland" a brand name. It is a generic term used to describe any cement that hardens in the presence of water and is made to standard specifications .. For all practical construction purposes, therefore, all cement is "portland." The name "port-land" was selected by the English inventor of the product in 1824 because concrete made with his product resembled natural building stone quarried on Portland, an English island. Although portland cement is not the final material which finds its way into completed construction, as the principal component of the most widely used construction material in the world, the location and process of its manufacture warrant some discussion

Jan 1, 1977