Search Documents

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion (Li-ion) battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V and 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicate that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Jan 1, 2024

By R. K. Dunham

It has been estimated that 30% of the United States coal reserves occur in the Western States at depths which would preclude exploitation by surface techniques. Much of this coal occurs in seams considerably thicker than those presently mined in other parts of the country. Recognizing the lack of technology and experience in exploiting the thicker seam range the Interior Department's Bureau of Mines is implementing a major "Mining System for Western Coal," research program which has as its ultimate objective the development and demonstration of underground mining methods and technology for extracting these seams. One investigation, being carried out by D'Appolonia Consulting engieers, under contract to the Bureau of Mines, is concerned with design of an entry system for longwall top slicing of thick western coal seams. This presentation presents an overview of some of the problems which have to be faced in designing such layouts.

Jan 1, 1977

By L. M. Cenegy

The formation of scale is common in gold ore processing plants. A working definition of scale, applicable to the various scaling conditions found in gold ore processing plants, would be: "a hard, tightly adhering deposit formed in place by the precipitation of calcium-bearing mineral compounds from water". The most common scale found in gold processing plants is calcium carbonate (CaCO3) although calcium sulfate (CaSO4) is occasionally a problem.

Jan 1, 1990

After the war that was nearing an end In early 1945, regular consulting work for Bralorne, the Bradleys, Pennsalt Chemical Co., and a directorship and occasional consulting for Homestake Mining Co. made it almost certain that in spite of my 61 years I would have enough work to feed my family. But this routine work would not provide enough income to lay up funds for the inevitable future when I could no longer do arduous work. And it would not give me the adventure that had first lured me into mining. Therefore I was greatly relieved as well as pleased when, in the 18 months from April 1945 to November 1946, I was asked to make three of the most adventurous as well as profitable examinations that ever came my way. Pati[n]o Mines, Bolivia The first of the exciting jobs was an examination of the Pati[n]o tin mines in Bolivia. After I had unsuccessfully tried to induce Anaconda to purchase these mines In 1915, the World War I crisis that had forced the half-Indian accountant to try to sell the mines had come to an end. The European market for tin improved dramatically, and "Don Simon" was able to borrow money for expenses while the concentrates were still In Bolivia. He took advantage of the favorable conditions by buying adjacent properties and increasing development work until his Bolivian tin mines were the greatest in the world. And his daughter had marled the French Count de Boisrouvain and was cutting a swath In high International society. Pati[n]o wanted to get rid of the drudgery of running a complicated mining Industry in a remote area In Bolivia when the fleshpots of Paris were much more seductive. An added incentive was the fact that his miners had become unruly and had even threatened his 11fe.

Jan 1, 1976

By Nolan B. Aughenbaugh

Zoning and environmental restrictions on land usage now make open- pit quarrying more and more difficult, especially near urban areas. One option for quarry operators is to go underground for mineral production. While underground-mining costs are higher than those for open-cut work, there are several compensating advantages. In many cases it is possible to produce the same material underground without affecting land values, and the surface is preserved for industrial, residential, or agricultural purposes. Proper planning can yield underground sites which have great potential value for industrial plants, warehouses, or other business uses. It is essential to plan underground mineral extraction using a three-dimensional modular-room architectural concept to fully exploit secondary space utilization. Prior to the start of underground mining an operator must make a careful geological engineering study to deter- mine the suitability of the deposit and must prepare a plan for safe and economical mining for the purpose of converting to secondary usage.

Jan 1, 1974

By F. Arslan

Gold extraction from refractory ores is still a problem. Gold losses in the cyanidation process are mainly due to the presence of sulfides and carbonaceous materials. Oxidation of carbon and sulfide minerals by sodium hypochlorite is a possible method to render the ore amenable to cyanidation, and earlier work by the USBM indicates that electrochemical generation of hypochlorite is promising. Laboratory work was carried out on the oxidation of pyrite and carbon in an electrochemical cell with a sodium chloride electrolyte. The results of preliminary tests are discussed in relation to the mechanism of electrooxidation of refractory gold ores and the estimation of current efficiency.

Jan 1, 1991

By R. L. Summers

The tremendous engineering advances occurring during this past century are very evident within the boundaries of the Anthracite Section of AIME. The Steelton plant of Bethlehem Steel Corporation, located along the Susquehanna River just east of the Commonwealth's capital at Harrisburg, for more than 105 years has experienced a most dynamic life which has paralleled America's industrial growth. (Figure 1) In June 1865, just after the Civil War, a group of men met to organize the Pennsylvania Steel Company. The war had brought into sharp focus the vital importance of the railroads to the country's expansion. Until that time wrought iron rails were used, and the replacing of track after only several months wear had become an almost unbearable cost. The spirit of free, competitive enterprise and the prospects of a lucrative market compelled these men to form that first Pennsylvania Steel Company and to develop better rail products. They issued the following statement: "...our desire to free ourselves from dependence upon a foreign market (has) led to the organization of the Pennsylvania Steel Company, and the parties who have connected themselves with it are determined to produce upon American soil all the principal manufactures of steel that are now, at such a serious cost for freight, commission, insurance, exchange, duty, etc., and often, with so much delay and uncertainty, imported from abroad. (We) are preparing to establish near the consumer, works at which articles of accustomed pattern will be promptly produced, and from the

Jan 1, 1971

By J. F. Peterman, M. C. Roberts

The success of any industrial mineral project requires an accurate forecast of the demand fir the material as well as accurate projections of costs and prices. This paper develops a general method of predicting mineral requirements and applies it to the case of graphite. The basic method is to explain graphite consumption in each of its major uses by the output and manufacturing technology of the using industry. Once these underlying factors are determined, they can he projected to establish future requirements. This forecast is critical to the evaluation of a new source of supply, such as the graphite resources of Upper Michigan.

Jan 1, 1990

By M. Nambiar

Due to the remote locations of the mining projects and the demand for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short circuit capacity. In order to cope up with this situation, more and more mining projects are considering the installation of appropriately designed Synchronous Condensers(SC) together with Power Factor Correction and Harmonic Filter System(PFC&HFS). The installation of these power quality equipments is viewed as a technological advancement in the mining application. An adequate level of short circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter driven gearless mill drive systems used for grinding application. Increase in plant short circuit power is generally achieved by lowering the impedance of the supplying network. The SC also provides smooth voltage control during mill starting or major load trips, thereby regulating the plant voltage within the required limits. This paper will explore the impact, technical advantage and reasoning for the selection of the advanced hybrid technology mentioned above, in order to cope with the power system challenges for future mining projects. It also highlights the potential problems and how to address them carefully.

Feb 23, 2014

By O. M. Johnson

Barite and bentonite are the two principal components of drilling fluid systems used in the petroleum industry for oil and gas well drilling with rotary-type rigs. Approximately 87 percent of the world's annual production of barite is used in drilling applications. Of the worldwide production of bentonite, an estimated 30 percent is used. The drilling fluid, or drilling mud, to which barite and bentonite are added, performs five distinct functions: Lubrication-The liquid phase of the drilling mud lubricates the drill bit, preventing premature failure of the cutting edges and bearings. it also helps to soften the formation being drilled. Cuttings Removal-A mud system must be able to carry rock cuttings broken loose by the bit up to the surface where they can be removed by mechanical or chemical methods. The fluid's ability to perform this function depends upon maintaining a proper balance between the rate of circulation of the fluid and the colloidal properties required to entrain the cuttings in the mud to prevent their settling to the bottom of the hole. Hole Stability-The pressure exerted by the mud against the wall of the bore hole prevents the collapse of the uncased portions of the hole. Downhole Information-The fluid characteristics of the mud should be such that good cuttings samples, cores and electric logs may be obtained to help evaluate a well's productive zones and potential. Control Oil, Gas and Water Flows-It is essential that a drilling fluid offset any pressure from naturally occurring formation fluids in order to prevent a potentially wasteful and dangerous blowout.

Jan 1, 1980

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Saturn light that significantly improves illumination for roof-bolting machine operators while reducing glare. The existing roof-bolter lighting was the baseline and was compared to the Saturn at 100, 75 and 50 percent intensities. Discomfort glare and disability glare were measured by the De Boer rating scale and the Mars Letter Contrast sensitivity test, respectively. Thirty study participants were tested. Discomfort glare was reduced at least three levels with the Saturn luminaire. Visibility levels were four to 6.5 times better with the Saturn than with the baseline. The Saturn design is freely available for commercialization.

By Richard Snyder

Secretariat of the Coal Mining and Mining Executive Committees' of the National Safety Council (NSC) and Manager of the memberships to both Mining Sections; Senior Consulting Safety Engineer, NSC; member of several committees for consensus Standards of the American National Standards Institute (ANSI); a Certified Safety Professional (CSP) of the Board of Certified Safety Professionals of the Americas, Inc. and a chief proctor for CSP testing and certification procedures, et al. It appears that the tunneling trade is merging into its own renaissance for the decade of the 1970s', and most likely on past the year 2001. Federal interest in underground excavation, and more specifically, rapid excavation expertise has been on the upswing since the latter part of the 1960's, mainly due to the pressing national needs for more raw materials based on the rise for material goods and the projective gloom of possible power shortages. On the pure tunneling side the national needs encompass, in the mainstream of priorities, rapid transportation and water supply excavation as the two top contenders. For instance, the estimates for tunnel mileage for the period 1968-1975 are:(1) Subways---85 miles Urban Highways--- 123 miles Intercity Highways---210 miles Water Supply Routes---528 miles at a total of 946 miles of tunnels. The estimated cumulative underground excavation demand in dollar amounts for the period 1970-1989 are:(1) Construction Oriented Demand--- $35 billions Mining Oriented Demand---$34 billions (which includes the coal-oriented demand on the order of 26 billions.

Jan 1, 1997

By I. B. Tulu, M. M. Sears

"In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial, yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground fall related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground fall related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 21 longwall mines were visited, representing about 40% of the currently active longwall mines in 4 of the 5 major US longwall producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. The results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries. INTRODUCTION Maintaining ground stability in gateroad entries is essential for longwall productivity and safety (Campoli, 2015). In 2015, 148 unintentional roof falls were reported in US longwall mines. About 34% of these resulted in mineworker injuries. Safety considerations not only include injury from roof and rib falls but also egress from the longwall face during an emergency (Mucho et al., 1999). Over the past 30 years, a number of researchers have studied longwall tailgate support performance (Mirabile, 2015). This research aims to take a snapshot of the ground support installed in modern US longwall mines and provide a supplement and update to the overview provided by Barczak (2005). This will provide a framework for future research into improving gateroad support systems. BACKGROUND Large unplanned roof falls at or above the primary support or those impeding travel and/or ventilation must be reported to the Mine Safety and Health Administration (MSHA). Reportable roof falls, normalized based on production in million metric tons, generally relate to the amount of roof exposed during the mining process (Pappas and Mark, 2012) and provide an evidence-based statistical background for this review of current support practices. Figure 1 shows the reportable roof fall rate in US underground longwall mines for the period 2006-2015 (MSHA, 2016). Over the past decade, roof fall rates have shown a gradual decrease with numbers now at a rate nearly half of what was observed just five years ago. However, over the past few years, roof fall rates in US longwall mines appear to have stagnated at levels just over 1 per 2,000,000 tonnes mined."

Jan 1, 2017

By C. D. Litton, I. E. Perera

This report presents the results of experiments to evaluate different types of mine fire sensors in an underground mine environment using a commercially available atmospheric monitoring system. To determine how well carbon monoxide (CO) and smoke sensors respond for purposes of fire detection, experiments were conducted using test fires of different mine combustibles and for both flaming and nonflaming combustion. The experiments were designed to assess the response of fire sensors to different contaminants and different contaminant levels produced from the test fires. The experiments were performed in the Safety Research Coal Mine at the U.S. National Institute for Occupational Safety and Health’s Bruceton Research Facility in the presence of an average ventilating air velocity of 1.6 m/s (315 fpm). Five fire sensor stations were located downstream of the test fire at fixed locations, with each sensor station consisting of four sensors: a CO fire sensor and three different smoke sensors, of which two were evaluated by the Mine Safety and Health Administration (MSHA) for intrinsic safety and the third was used extensively in underground mines overseas but not evaluated by MSHA for intrinsic safety. All four sensors were mounted near the center of the entry and in the upper onethird of the entry height. A UL-listed combination ionization and photoelectric smoke sensor was mounted near the roof at the first sensor station and its responses were compared against the responses of the four CO and smoke fire sensors. Sensor response data, contaminant travel times, and the impact of fire on the existing ventilation flow are discussed as they apply to earlywarning fire detection. Of significance in the analysis is the need for performance standards for mine fire sensors in order to provide for consistent and timely early warning of developing fires.

Jan 1, 2014

By R. McCulloch

Exploration activity in metallic minerals continued to decline in Montana in 1992 as companies either reduced budgets or left the state. The number of active projects dropped another 50% from 1991. Expenditures were 3% to 6% of 1989's 28.6 million. Many of the major mining companies closed offices in Montana. Although depressed commodity prices have hurried the exodus, continuous changes in environmental regulations, as well as the Mining Law of 1872, without regard to economic effect have had the most serious impact. Many companies indicate that Third World countries present a more stable business environment than the United States. Grassroots projects are nearly non-existent, while late-stage programs continue cautiously. Exploration activity continued at the following projects: Garnet, Pegasus Gold; Southern Cross, Asarco; Elkhorn, Goldfields; 7-Up-Pete, Phelps Dodge and Canyon Resources; Miller Mountain, Pegasus Gold; Sheep Creek, Cominco American Resources; Checkerboard, Kennecott and BHP Utah International; Emigrant Creek, Pegasus Gold; and Crevise, American Copper and Nickel. All mineral activity, whether on private, state or federal land, is regulated by the Montana Department of State Lands under three classes of permits - Small Miner Exclusion Statements (SMES), Exploration Licenses and Operating Permits. A total of 230 Exploration Licenses are active in the state with 26 of those being new. However, there are only 433 projects current in Montana, with many of those in the reclaiming stage. The majority of exploration projects consist of individuals expending time rather than money on properties. The number of mines functioning under operating plans declined by one when W.R. Grace closed its Zonolite operation.

Jan 1, 1993

By R. Venugopal, V. K. Saxena, A. K. Mukherjee

"Coal, iron and manganese ore samples were exposed to different ultrasonic intensities of 250, 300 and 350 W/L for five minutes and to an ultrosonic intensity of 270 W/L for different time durations of 3, 5 and 7 minutes. The ultrasonically treated samples showed reductions in D80 particle diameters of 6 percent for the coal samples, 5.95 percent for the iron ore samples and 35.63 percent for the manganese ore samples during grinding. The ultrasonic treatment was also observed to assist in reducing ash content in the coal product by 8 percent and to reduce manganese losses in rejects by about 5 percent. Ultrasonic treatment was concluded to be capable of assisting in the comminution of friable ores more prominently than the hard and porous materials.IntroductionComminution is an important unit operation in the mineral-processing, cement-making, powergeneration and pharmaceutical industries. But most of the milling technologies are considered to be energy inefficient, with less energy consumed in real size reduction and most of the energy consumed in the machine. This is more critical for the mineralprocessing industry because of the growing need to exploit lower-grade ore bodies and process rejects (Blazy et al., 1994; U.S. Department of Energy, 2005). Low-grade ores require crushing and grinding to liberate the valuable minerals, which are further separated from gangues by various beneficiation methods such as gravity separation, flotation and leaching. Various studies have been carried out to minimize energy consumption during milling by developing pretreatment methods that can initiate new fractures or improve the fracture density in materials before comminution. These studies were mainly focused on chemical additives; thermal, ultrasonic and microwave treatments; and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman, Briggs and Kojovic, 1997; Gaete-Garreton, Vargas-Hermandez and Velasquez-Lambert, 2000; Kumar et al., 2010; Wang, Shi and Manlapig., 2011, Singh et al., 2012).The fragmentation effect of ultrasonic fields in solids has been investigated since the 1950s, and Gärtner was probably the first researcher who attempted it (Gaete-Garreton, Vargas- Hermandez and Velasquez-Lambert, 2000). Sound waves can propagate in solids in the form of longitudinal waves, shear waves and surface waves, and in thin materials as plate waves.In surfaces, fractures and interfaces, various types of elliptical or complex vibrations of the particles make other waves possible. During ultrasonic-vibration treatment, cavitation bubbles nucleate, grow and collapse, generating microjets, whose impacts on the particles initiate microcracks. The ultrasonic waves can enhance the nucleation, growth and coalescence of flaws, caused by tensile or shear stress. The mechanisms operating in the materials and inducing these stresses have been identified as spall and compression-induced tensile microcracks, nucleating at preexisting flaws. These mechanisms are driven by the shock wave and cavitation effects in the surrounding fluid (Chen, Huang and Shih, 2003)"

Jan 1, 2016

By R. E. Scheffel

In February, 1976, Ranchers Exploration and Development Corporation obtained an option from Foote Minerals, Inc., to evaluate reprocessing of two uranium tailing piles. Foote received ownership of the Naturita and Durango tailing piles in 1967 through the purchase of Vanadium Corporation of America. The option was exercised in November, 1976, after initial testwork proved that a viable extraction technique existed. Preparation for production at Naturita began immediately with engineering and en¬vironmental permitting proceeding simultaneously. Production began in December, 1977, just 22 months after acquisition of the property and-was completed 17 months later.

Jan 1, 1981

By Chris Ashton, Andreas Rädle, Taner Aydogmus

"The Contract C310 is part of the current biggest infrastructure project of Europe “Crossrail” which is a major new cross-London rail link project and comprises the construction of the North Woolwich Portal, Plumstead Portal and the twin tube Thames Tunnels with a length of approximately 2.6km. Two Mix-Shield TBMs (Diameter 7.12m) were driving through differing challenging ground conditions (Thanet Sand, Gravels, Flint and Chalk) below the ground water table. The two tunnels were underpassing several listed buildings, sensitive structures, operational railway tracks with low overburden and close to existing subway tunnels in an urban environment. Several additional measures as compensation grouting, micro piles and an intensive monitoring has been carried out to ensure a safe tunnelling process. PROJECT OVERVIEW CROSSRAIL Project Crossrail Crossrail is currently the biggest infrastructure project in Europe which has been developed to serve London and the southeast of England. The project includes the construction of twin-bore tunnels on a west-east alignment under central London and the upgrading of existing National Rail lines to the east and west of central London. The new rail track, as shown in Figure 1, starting in Shenfield/ Abbey Wood in the east of London and ending in Reading / Heathrow Airport in the west of London, includes the construction of nine central area stations, providing interchange with London Underground, National Rail and London Bus services, and the upgrading or renewal of existing stations outside central London.Altogether there will be 118km of new rail tracks, including 42km of tunnels and 40 train stations. After completion in 2018, Crossrail expects 200 million passengers per year (Tauriainen, Rädle, Ingram 2013)."

Jan 1, 2016

By S. M. Khandrika

Most of the coal presently used by the utility industry is cleaned at preparation plants employing wet processes. While water is the mainstay of coal washing, it is one of the least desirable components in the final product causing a reduction of the heating value as well as handling difficulties. Currently available dewatering techniques are inefficient for dewatering very fine coal (minus 325 mesh). The US coal industry has expressed serious concern about utilizing advanced cleaning processes such as column flotation because an efficient and economical dewatering process is not available.

Jan 1, 1992

By Alphonse C. Van Besien

It is doubtful if anyone knows precisely how many U.S. coal miners have been killed by roof falls. In 1931, 51 miners were killed by falls or rock in every 10-day period (Paul, 1). Roley (2) indicated that from 1882 to 1945, over 3,700 men were killed by roof falls in Illinois alone. During this 63-year period, roof falls accounted for 47.6 percent of the coal mine accident fatalities. Similarly, Price and Nolting (3) reported that during the 10-year period beginning in 1937, roof falls claimed over 50 percent of the lives lost in West Virginia coal mines. Over 150 miners died under fallen rock in West Virginia alone, in each of those years. Certainly, the statistics have improved over the years. The Theodore Barry Report of 1971 (4) indicated that during, the previous 4 years, fewer than 100 miners per year lost their lives to roof falls--in the entire United States. The improvement is less remarkable when it is realized that the accident rate has declined only as the number of miners employed underground has declined. The TRW Report (4) pointed out that although the number of fatalities in underground coal mining (from all causes) had been cut in half from 1956 to 1965, the fatality rate per thousand miners had remained virtually constant. The decreased accident rate was due not to a reduction in hazards but to a reduction in work force. Roof falls still claim approximately 50 percent of the lives lost in underground coal mines. Considering the increased underground production of coal which must result from our energy crisis, the environmentalists' pressure against strip mining, and our inevitably diminishing supply of strippable coal, it is apparent that some means must be found to reduce the number of lives claimed by coal mine roof falls.

Jan 1, 1973