Search Documents

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. IntroductionAbout one-half of U.S. underground coal is produced by longwall mining, which allows for mining high volumes of coal but generates significant amounts of coal mine dust. This can lead to overexposures for longwall miners and possibly occupational respiratory diseases, including black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities (Mine Safety and Health Administration (MSHA), 2015a). When respirable quartz is present, the mine must maintain average concentrations at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present (MSHA, 2015b)."

Jan 1, 2018

By J. F. Childs

"INTRODUCTION Comprehensive overviews of the world-class talc deposits and related prospects in Montana were published by Olson (1976) and by Berg (1979). Both of these compilations include detailed descriptions and maps of the talc deposits and occurrences and were followed by a regional map and summary descriptions of the talc deposits published by Van Gosen et al. (1998). More recent publications, descriptions and field guides for some of the deposits include Underwood et al. (2014), Cerino et al. (2007), and Cerino (2002). The present paper focuses on some of the more recent ideas regarding talc formation that have developed since the publication of the earlier overviews. Olson (1976) reported that talc production from the deposits in southwestern Montana was over 200,000 tons in 1974 and that talc production had doubled between 1969 and 1974. The last year for which the U.S. Geological Survey published production records for talc by state was 1993. Production in Montana in 1993 was 350,000 tonnes (Virta, 1994). Remaining reserves are substantial at all three of the producing mines in the district. Minerals Technologies Inc., the parent company of Barretts Minerals Inc., stated in its 2014 annual report that it has reserves of 2,791,000 tons of talc. Imerys stated in its financial report for 2014 that it had 19,638,000 tons of proven and probable talc reserves at its North American mines. Although the Imerys reserves were not reported by individual mines or states, a large proportion of the total reserves would likely consist of the reserves at the Yellowstone mine, located south of Ennis, Montana. Talc mined in southwestern Montana is of high purity and is the quality used in a wide variety of applications including paints, ceramics, plastics, rubber, coatings, agriculture, cosmetics, and pharmaceuticals. GEOLOGIC SYNOPSES FOR MAJOR MINES AND COMMENTS ON REGIONAL DISTRIBUTION OF TALC OCCURRENCES The general geology of southwestern Montana is shown in Figure 1along with the locations of the three producing talc deposits in the area and the extent of pre-Belt marbles that host all of the talc mines and prospects. The term “pre-Belt” is used in the present paper because zircon and other radiometric data developed in recent years indicates that the metamorphic rocks that form the crystalline basement for the middle Proterozoic Belt basin in the Dillon Tectonic Block of southwestern Montana includes both Archean and Paleoproterozoic rocks (O’Neill et al., 1996; Foster et al., 2006; McDonald et al., 2012). An envelope or “corridor” has been superimposed on the geology in Figure 1 which encompasses all of the talc deposits that have a significant resource. This “talc corridor” will be discussed in later sections of this report. The more important talc deposits are discussed in this report section."

Jan 1, 2016

By U. Schoepf

Economic and at the same time environmentally acceptable mining of small vertical ore bodies and veins to great depths has always been a challenge for miners. The Bauer cutter system, widely used in civil engineering, has been further developed for applications in exploration and mining, to a sustainable system for selective mining with a focus on small vertical ore bodies and veins, as well as residual ore in open pit operations. Current situation of conventional mining of small ore bodies and vertical veins Small ore bodies and vertical or near-vertical ore veins often pose a challenge to the mining industry. The relatively small size of the ore deposit over great depths or lengths, with only limited exposure to the surface makes economical mining difficult. Open pit mining of such ore bodies must either be terminated early because of the high stripping ratio and the enormous environmental impact or is unprofitable from the very beginning. The required massive stripping of waste rock leads to high material hauling times and costs, intensive roadway and bench construction and maintenance, possible safety hazards due to heavy vehicle movement, pit wall stability risks, intensive surface water management and massive waste dump requirements. In addition, it can be assumed that increasingly extensive rehabilitation measures will be required in the future after mine closure. Particularly in vertically oriented magmatic and hydrothermal deposits the technical, economic and environmental limits for further pushbacks, to extend the open pit depth, can lead to an early end of mine life even if a significant quantity of residual ore is left behind. Going underground is only a viable option in a limited number of mines with very high ore values and volumes. The high development cost of an underground mine, as well as the higher underground mining costs, often prevent further mining to greater depths.

Feb 1, 2023

Evver since it first displayed an autonomous mining truck at the 1996 MinExpo show in Las Vegas, NV, Caterpillar has been building the blocks to a fully autonomous mine. In May, the company unveiled another block in that progression, the new Cat MineStar System that it says is ?the industry?s broadest, most comprehensively integrated miner operations and mobile equipment management system.? The full system is comprised of five capability sets ? Fleet, Terrain, Detect, Health and Command ? to help operators define the size and scope of their management system based on the needs of their mining operations. Michael Murphy, technology and autonomy manager for Cat Global Mining, explained that the customers were not ready for an autonomous mining truck in 1996, but that many customers wanted the building blocks to eventually get to autonomous mining. After 15 years of work, Murphy said the building blocks have come together in the form of the Cat MineStar System.

Jan 1, 2011

By J. David Gunn, Richard W. Lawrence

Gold and silver often occur finely disseminated in sulphide minerals such as pyrite. The use of biological leaching to dissolve pyrite and liberate gold has been extensively studied for a concentrate from the Porgera deposit, Papua New Guinea. The successful operation of a continuous bioleach circuit has been demonstrated. Bioleach residues were cyanide leached to extract gold and silver, and unreacted pyrite recovered for recycle to the bioleach. A 26 day steady state continuous bioleach test on a concentrate assaying 14.3 g/tonne Au and 87.0 g/tonne Ag produced residues with an average 73.5% weight loss and a pyrite oxidation of 88%. Cyanidation and recovery of pyrite from the cyanide residues for recycle gave overall recoveries of 92.1% gold and 74.6% silver. A proportion of the remaining precious metals was found in the bioleach solutions and may be recoverable. Losses to tails were 3.0% gold and 8.1% silver. Final tails represented 14.3% of the feed weight and averaged 1.84 g/tonne Au. A description of the continuous bioleach circuit and bioleach residue handling procedures, and the results of the study are presented. The features and advantages of biological oxidation as a pretreatment for refractory precious metal ores and concentrates are discussed.

Jan 1, 1985

By H. Colijn

Vibratory or oscillatory conveyors can be found in all types of industry, handling virtually any granular bulk material, often at elevated temperatures. These conveyors can be combined with other process functions, such as screening, cooling, drying and dewatering, while conveying. Although construction and installation is relatively simple, the engineering and design analysis of the vibratory mechanics is fairly complex. This paper will discuss the basic types of vibratory conveyors and the analysis of the material movement along the carrying trough.

Jan 1, 1985

By Valerie Kollonitsch

Functional mineral pigments are used in large quantities in paint, paper, plastics, rubber, textiles, agriculture, and several other industries. U.S. consumption in 1969 is estimated at over 5 million tons a year, valued at nearly $150 million, as shown in Table 1. Originally extender pigments were employed only to lower cost. They were thought of merely as adulterants to replace more expensive prime pigments and binders. However, over the years their role has become better understood, and today their main functions are: - Increasing strength, stability, and service life. - Improving surface properties. - Enhancing application and processing properties. - Extending prime pigments. - Controlling viscosity and package stability - Lowering overall costs of the finished product. The principal minerals used as functional pigments are kaolin, ground calcium carbonate, talc, and asbestos. Other minerals include barytes, attapulgite, diatomite, mica, ground silica, wollastonite, and nepheline syenite. Several synthetic products, including precipitated calcium carbonate; precipitated, gel, and fumed silica; alumina trihydrate; and barium sulfate, compete with mineral products. They are more expensive, but often have more closely controlled particle size or other properties because they can be tailor-made according to the requirements. This paper covers only natural products selling for $10 or more a ton, approximately the lower limit for pigment grades. Data refer only to consumption in pigment applications. For example, such applications as filter aids for diatomite are not included. Key properties of the major mineral pigments are given in Table 2. It is important to note that these properties are primarily physical rather than chemical. In general, these products are sold to performance specifications for what they can do rather than on chemical composition specifications on what they contain.

Jan 1, 1969

By S. Frimpong, E. Siami-Irdemoosa, S. R. Dindarloo

"Electric and hydraulic shovels are the dominant loading machinery in surface mining operations. Despite their critical role in production and their high capital and operating costs, no reliable and comprehensive quantitative performance metric is available. In this paper, a stochastic shovel effectiveness (SSE) measure is proposed for the purpose of quantifying the performance effectiveness of these shovels. The SSE is based on the widely used method of overall equipment effectiveness (OEE) in the manufacturing industry. The OEE measures the performance effectiveness of equipment by multiplying its mechanical availability, utilization and production quality. In manufacturing processes, quality rate is the ratio of the total number of products minus the number of defective products – equivalent to the number of acceptable products – to the total number of products. The SSE similarly uses the mechanical-availability and utilization terms, but instead of quality rate it uses a new parameter named bucket rate.The variability or randomness of the input data, that is, availability, utilization and bucket rate, are further incorporated into the SSE, and a final stochastic SSE distribution is derived in the form of a probability density function. One hydraulic and one electric shovel in a surface mining operation were selected to test the validity of the proposed method. The SSE scores for the two shovels, operating continuously for one year, were derived and compared. As with the OEE, the three-parameter SSE method yielded more representative results for overall performance measurement than a single-parameter approach. Using Monte Carlo simulation, a three-parameter Weibull and a normal distribution were derived for quantifying the overall effectiveness of hydraulic and electric shovels, respectively. As a decision aid, the proposed methodology promises to render a more informative tool than traditional metrics for mine equipment maintenance and management."

Jan 1, 2015

By S. S. Klima, D. E. Pollock, J. A. Organiscak

"Airborne respirable coal dust capture by water sprays or wet scrubbers has been studied and developed over many decades as an engineering control to reduce dust exposure in coal mines and combat coal worker pneumoconiosis. Empirical relationships and deterministic models for particular dust capture experiments have previously been devised to show the key parameters involved in airborne coal dust capture. Many of the results from these models show that the significant parameters related to airborne dust capture are water spray pressure, water quantity, water droplet size, relative water droplet-to-dust particle velocity, and total operating air pressure of the scrubber. However, many airborne dust capture efficiency relationships and models developed for particular experiments cannot be readily applied to forecast the dust collection efficiency of different spray and scrubber design configurations, which rely on several key dimensional engineering measures. This study examines engineering measures from previous water spray and wet scrubber experiments conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and the U.S. Bureau of Mines (USBM) to develop empirical models for wet collection of airborne dusts. A dimensionless empirical model developed for predicting airborne dust capture efficiency of water sprays and wet scrubbers is presented. IntroductionWater sprays have been one of the earliest mainstay engineering controls used to suppress respirable dust in underground coal mines. Some of the earliest reports of water spray usage on continuous mining machines indicated respirable coal mine dust reductions of 20 to 60 percent (Kobrick, 1970). Not long after the enactment of the 1969 Coal Mine Health and Safety Act, the U.S. Bureau of Mines (USBM) and others conducted extensive research into water spray and wet scrubber systems to control respirable dust in coal mines. The primary aspects of water spray dust control included prewetting for dust prevention, localized ventilation redirection and airborne dust capture, which are summarized in handbooks or best-practices guides (Kost, Yingling and Mondics, 1981; Kissell, 2003; Colinet et al., 2010). Initially, underground studies were conducted to identify the primary sources of dust during the mining processes and effective dust controls (Courtney, Jayaraman and Behum, 1978; Jankowski and Organiscak, 1983). Laboratory research systematically studied ventilation and airborne dust capture effects of water sprays and scrubbers to improve their application in underground coal mines (Tomb, Emmerling and Kellner, 1972; Divers and Janosik, 1978, 1980; Grigal et al., 1982; Ruggieri et al., 1983; Jayaraman, Jankowski and Kissell, 1985; Volkwein, Ruggieri et al., 1985; Jayaraman, Schroeder and Kissell, 1986; Divers, Jankowski and Kelly, 1987; Jones and James, 1987)."

Jan 10, 2018

By Peter Werner

Technological advances in mine equipment and milling processes have enabled mining companies to exploit ever lower grades of ore. The result has been larger disturbances, greater volumes of waste, a complex web of infrastructure, and an overall trend toward mega projects that can extend over several square kilometers. This explosive growth in a mining operation’s disturbance footprint provokes an obvious question: What is it going to cost to reclaim all of this? At face value, this can be an enormous financial liability for a company, but since the timing of reclamation may be years in the future for many operations, these costs can be heavily discounted, thereby limiting the burden on the corporate balance sheet. Nonetheless, mining companies are eager to remove these liabilities as quickly as possible; conversely, regulators want assurance reclamation will, in fact, occur. How might one bridge these competing interests? Navigating the practical and financial requirements of a post-closure landscape requires foresight, judgement and assumptions; however, companies that do not adequately plan for these future expenditures when there is no offsetting income stream will likely face some difficult decisions. Simple risk analysis tools and utilizing the time value of money can help bring some clarity to this end-of-mine life phase.

Dec 1, 2025

By Yassine Lahmadi, Edoardo Trivellato, Christian Chereau, Bénédicte Robert

Within the framework of the adaptation of the South-East European Technicentre (Technicentre Sud-Est Européen TSEE), SNCF Voyageurs appointed Pini with the project management mission (MOE) for the design and construction monitoring of a road tunnel. This investment has a dual function: during the site transformation phase, it facilitates the work logistics (and shorten traffic flows); and in the operating phase, it is intended to ease all movements on the site over the long term. This is a limited-length gallery (50 meters) to be performed in conventional excavation below Poniatowski Avenue (Paris 12e). The excavation, crossing the entire width of the boulevard, constitutes a major challenge, given the very low coverage (less than 5.5 m), and the surrounding main infrastructures. The same project mis- sion includes the design of the tunnel accesses, via reinforced-concrete frame structures. The targeted design questions several aspects of its execution framework, and particularly, continuous operation must be guaranteed to the neighboring networks during the works. The installation of an umbrella- pipe all along the excavation profile, the progression in divided sub-sections, and the implementation of a complex monitoring system are hence key elements for limiting and controlling any deformation. An exhaustive 3D finite element modelling was performed, taking into account the detailed phasing of construction (pre-support, excavation in divided section, preliminary support and definitive lining), to dimen- sion the structures, and, overall, to analyze the impacts on the neighboring structures and facilities. During the execution phase (planned for mid-2024), monitoring activities with back-analyses as close as possible to the works are planned.

Jun 23, 2024

From some of the largest tunnel projects in the some of the most vibrant cities, to smaller projects in remote corners of the globe, the Robbins Co. announced two tunneling projects in which its tunnel boring machines will be used. Robbins earth pressure balance (EPB) machines undercut Downtown Zhengzhou. Zhengzhou, a city of 7 million people, is set to become a crossroads for rail commerce in China. The country?s future main routes, traveling between Beijing and Guangzhou (North-South), and between Xuzhou and Lanzhou (East-West), will intersect in the city. The plan includes up to four rail lines in Zhengzhou itself, which will eventually link up to the national lines. Excavation of Zhengzhou Metro?s new Line 1 tunnels began on Sept. 28, 2010, when the first of two 6.3-m (20.7-ft) diameter Robbins earth pressure balance (EPB) machines was launched from a 16-m- (52-ft-) deep shaft.

Jan 1, 2010

By P. J. Arps

Cyanide (CN) is used to recover gold from its ores in many locations worldwide. In spite of the established history of gold mining in Alaska, modern cyanidation methods have been used at only one location, the Ryan Lode Mine at Ester Dome, near Fairbanks. Ore was processed by heap leaching between 1987 and 1989, when permitting issues caused operations to be terminated. Those issues have since been resolved, and plans to reopen the mine are currently being discussed. Plans are also proceeding to develop several other ore deposits in the state, all of which include the use of cyanide for gold recovery [6]. Since tailings and effluent water produced from these mines will require treatment, it is important to develop detoxification methods suitable for the Arctic and sub-Arctic conditions found in Alaska. Several methods exist for removing cyanide from mining wastewater. However, most industrial users prefer chemical treatment systems, and typically use sodium hypochlorite, hydrogen peroxide, or sulfur dioxide/air/copper to oxidize free and complexed cyanides [9]. Biological treatment has been used successfully at two sites in the United States [30,32] and field tested at several others [20,27,28]. In addition, one mine uses "natural processes", which include natural oxidation, photodegradation, and degradation by naturally occurring bacteria [33].

Jan 1, 1994

16.1.1-VENTILATION'S ROLE Importance of Ventilation and Environmental Control-Mine ventilation is necessary for the preservation of human life and for the conduct of operations involved in the underground extraction of minerals. It clearly is the most essential of the functions attendant to mining, yet it is auxiliary to the primary objective in mineral extraction. Ventilation in mining thus poses a paradox: ideally, it should be carried out with minimum interference with and cost to production operations, yet it is absolutely vital in providing adequate environmental con¬ditions to support mining. Deterioration of the atmosphere, along with rising ground pressure, imposes the ultimate constraint with depth in underground mining. Ventilation requirements and costs rise rapidly with depth. To preserve atmospheric quality under intense heat conditions, ventilation at great depths must be supplemented by air condition¬ing. Likewise, when mining at any depth under severe or excessive conditions of gas, dust or humidity, supplementary control measures must be employed. In recent years, environmental standards in mines have been raised substantially. While limits are based on human tolerance, increasing concern is being expressed for standards of human comfort. The reasons are economic, as well as humanitarian. Worker performance and longevity correlates closely with environmental quality. Further, adverse accident and insurance compensation rates are a consequence of unsatisfactory environmental conditions. No mining company can afford to be lax in its environmental and ventilation practices. Functions and Processes-Ventilation is the control of air movement, its amount and its direction. As a means of quantity control, it is one of the constituent processes of total air conditioning, the simultaneous control within prescribed limits of the quality, quantity and temperature-humidity of the air. Ventilation is the most common and most. important conditioning process employed in mines for air environmental control. In mine ventilation, air is coursed through the mine workings and openings themselves and, for auxiliary purposes, through vent tubing and ducts. Thus, many interdependencies exist between the mining system and ventilation method. In fact, the two often have evolved ,jointly, as in room-and-pillar extraction of bedded or tabular mineral deposits, such as coal. Ventilation in mines today is provided almost exclusively by large fans, although air flow may result due to natural (thermodynamic) conditions. As mines increase in depth, size and complexity, demands on the ventilation system to maintain more stringent standards of environmental quality likewise rise. On the other hand, never have the technology and resources of the mining industry to cope with environmental problems been so well developed as they are today. In spite of rising costs, it is unlikely that further progress in mine ventila¬tion and air conditioning must await technological breakthroughs. 16.1.2-NATURE OF THE MINE ATMOSPHERE Air Mixtures-Air is a gaseous mixture comprising the natural atmosphere at the surface of the earth. Thermodynamically, it may be thought of as a mech-

Jan 1, 1973

By R. R. Cellan

There have not been many opportunities to date for comparison between laboratory and commercial neutralization rinse data. Homestake Mining Company's Santa Fe project is one such comparison. This paper discusses laboratory procedures and results from a 100' leach pad height simulation column neutralization rinse test and compares principal data with that achieved in actual commercial leach pad neutralization rinsing procedures. Principal comparisons include the rate of WAD cyanide neutralization, decrease in effluent pH, stabilization of dissolved silver and copper, and the quantity of dissolved gold recovered during rinsing.

Jan 1, 1996

By J. Herbst, C. C. Harris, G. Poling

The modern flotation machine is the result of decades of adaptation to a changing environment. In response to falling ore grades, and rising demands, tonnages, and costs, attempts are now underway to expand machine capacity by about an order of magnitude, while at the same time maintaining metallurgical performance and if possible reducing power requirements per unit throughput. Empiricism and rule-of-thumb have guided flotation machine design and scale-up, and a current need is for the development of a fundamental understanding of the subject. Design features of current and some obsolete machines are discussed in an attempt to outline those principles of flotation machine design which are known, and to delineate topics needing investigation. Attempts are made to distinguish between essential machine features required by the physics of the process, those features resulting from speculative theories on the flotation mechanisms, and features which are essentially styling variations. Topics discussed include: flotation mechanisms; tank and impeller/ stator design and dimensions; impeller speed; aeration; power consumption; particle suspension and dispersion; capacity; correlation of design parameters and operating variables; scale-up and scale- down; materials flow; problems in machine design. Design details and operating data for several current machine families are provided in Appendices.

Jan 1, 1976

By Antti Porvali, Vivek Agarwal, Mari Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2·H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can then be further converted with NaOH solution to form REE hydroxides. However, present literature has paid little attention to how to minimize the consumption of reagents in this recovery process. In the current study, a process model was built using HSC Sim software, and metamodeling of the simulated flowsheet was conducted with the design of experiments (DOE), after which the basic functionality of the flowsheet was verified by experimental work, starting from sulfuric acid leaching of spent batteries. As the process is based on chemical circulation internally in the process, the objective was to investigate the accumulation of the elements in solution, specifically Na+ , K+ , SO4 2− ions and impurities liberated in the NaOH conversion step. It was found out that metamodeling could be utilized in obtaining first estimate of the process behavior, prior to any experiments. Flowsheet functionality with circulated solution was confirmed, obtaining at best 96.9% La recovery.

By J. Kretschmann, K. Sakamornsnguan

"Sustainable development is an influential ethical concept in modern mining management. However, the concept is not culturally neutral because it is based on Christian, Western values. These values can be very different from traditional values in emerging mining countries like Thailand, where Buddhist values are dominant. When applying the concept of sustainable development, these differences should be taken into account. Different values imply different interpretations of ‘good mining’. They have a significant impact on how mining operations are evaluated, perceived, operated and managed. This paper attempts to integrate Buddhist principles with approaches of the sustainable development concept. When local values are appreciated and maintained, mining companies and their external stakeholders can identify objectives and approaches that match with their own values and contexts. Practices based on this integrated ethic can help to promote sustainable mining and to minimize communication risks for enterprises in mining countries like Thailand. INTRODUCTION The objective of this paper is to integrate Buddhist principles to the application of sustainable development concept to mining activities. The structure of this paper is divided into four parts. An introduction provides basic information about Thailand, its mining industry and the role of Buddhism on the past development. The second part compares the differences between the sustainable mining framework and the implications of Buddhist principles on mining. In the third part, the core Buddhist teachings are integrated into the sustainable mining framework. This is followed by conclusions in the last part. THAILAND, BUDDHISM, AND MINING Thailand is a constitutional monarchy state in Southeastern Asia with a population size of around 65 million [1]. Its GDP in 2013 was 391 billion USD [2], predominantly deriving from manufacturing (38%), trade, transport and communication (24%), agriculture (8%) and mining and construction (4%). Still the largest part of the Thai workforce (39%) is working in the agricultural sector. The remaining part of the workforce is equally distributed across services, manufacturing, and mining and construction sectors. [3]"

Jan 1, 2015

By Z. Henderson, J. R. Saylor, L. Rojas-Mendoza

"Diesel particulate matter (DPM) is a major occupational health hazard in underground mine environments, even with available abatement technologies. Prior work has demonstrated that micrometer-scale water droplets, or “fog,” may be effective in removing significant number fractions of DPM from a conditioned exhaust stream. Here, a series of laboratory experiments are described which demonstrate that such a treatment can remove significant DPM mass from an unconditioned stream. The removal mechanism involved coagulation of the DPM and drops. The fog treatment removed about 45 percent more DPM mass on average than no treatment. Varying engine load, flow rate and fog droplet number density did not significantly affect the results under the range of conditions tested. IntroductionDiesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy (Heywood, 1988). Recently, however, the adverse health risks of diesel exhaust have become increasingly clear. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are an ultrafine mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash (Kittelson, 1997). DPM is generally considered to occur almost entirely in the submicrometer range. It is classified as a carcinogen (Occupational Safety and Health Administration, 2013), and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustionrelated fine particulates and increased cardiovascular and pulmonary diseases (Pope et al., 2002; McDonald et al., 2011). Many of the risks of diesel exhaust are associated with the physical and chemical properties of exhaust components (Heywood, 1988; El-Shobokshy, 1994; Kittelson, 1997). Exposures are generally measured and regulated on the basis of mass concentration. However, DPM number density and particle size are increasingly recognized as critical factors in terms of health outcomes (Bugarski et al., 2012; Kittelson, 1997; Occupational Safety and Health Administration, 2013; Pope et al., 2002)."

Jan 11, 2017

By Curt Swanson, David C. Mathy, Dru R. Nielson, Kent VonAspern

In 1997, Central Contra Costa Sanitary District undertook the design of the Martinez East Side Trunk Sewer Improvements Project. Microtunneling was specified for approximately 1,035 meters (3,400 feet) of 600-mm (24-inch)diameter pipeline to be installed through estuarine soil deposits (San Francisco Bay Mud) and alluvium beneath the congested city streets of downtown Martinez, California. Directional drilling was specified for approximately 275 meters (900feet) of 200-mm (8-inch) diameter pipeline in four separate segments to be drilled through bedrock within narrow utility easements between residential properties. This paper presents a case history for the design and construction of themicrotunneling and directional drilling aspects of the project.

Jan 1, 1999