Search Documents

By Z. Jin, D. DePaoli, P. Zhang

"Phosphogypsum is a byproduct created during the production of industrial wet-process phosphoric acid. This study focused on recovering rare earth elements (REEs) from a Florida phosphogypsum sample and investigated the effects of removing detrimental impurities such as phosphorus pentoxide (P2O5 ), uranium (U) and fluorine (F) during the leaching process. Experimental results indicated that REE leaching efficiency increased rapidly, reached a maximum and then began to decrease with sulfuric acid concentrations ranging from 0 to 10 percent and temperatures ranging from 20 to 70 °C. At a sulfuric acid concentration of 5 percent and leaching temperature of 50 °C, REE leaching efficiency obtained a maximum value of approximately 43 percent. Increasing the leaching time or liquid/solid ratio increased the leaching efficiency. The leaching efficiencies of P2O5, U and F consistently increased with sulfuric acid concentration, temperature, leaching time and liquid/solid ratio within the testing ranges. A fine-grain gypsum concentrate, sized smaller than 40 µm, was separated from leached phosphogypsum through elutriation, in which the P2O5, U and F content levels were reduced by 99, 70 and 83 percent, respectively, from their content levels in fresh phosphogypsum. IntroductionPhosphogypsum is a byproduct generated during the industrial wet process of phosphoric acid production, in which sulfuric acid is used to digest phosphate rock. Gypsum (CaSO4·2H2O), the main component of phosphogypsum, usually accounts for 65 to 95 percent of phosphogypsum by weight.There are small quantities of impurities in phosphogypsum, such as phosphates (H3PO4, Ca(H2PO4)2·H2O, CaHPO4·2H2O and Ca3(PO4)2), fluorides (NaF, Na2SiF6, Na3AlF6, Na3FeF6 and CaF), sulfates, trace metals and radioactive elements (Rutherford, Dudas and Arocena, 1996). Global phosphogypsum generation is estimated at 200 Mt/a (Parreira, Kobayashi and Silvestre, 2003; Yang et al., 2009), but only about 15 percent is recycled as building materials, agricultural fertilizers or soil stabilization amendments (Tayibi Choura and Lopez, 2009)."

Jan 1, 2017

By J. Chai, Y. Qiang, D. D. Zhang

"In order to control Quaternary loose layer settlement in East China, there are monitoring results based on the 3 water level observation holes and 7 sand layer of fiber Bragg grating (FBG) strain sensor. Un-der the conditions of upper group water injecting to lower group of loose layer, the deformation characteristics of upper, middle and lower group of loose sandy soil layer changing with time and relationship with the water level are studied. The constitutive relation of stress-strain is also studied at different sand layers. Research results show that using water injecting from upper group into lower group of loose layer can ease the loose layer compression deformation. With the water level dropped, in East China soil creep deformation occurred, which accord with viscoelasto plastic model. The deformation of lower sand group has clear later effect and no direct relationship with water level. The results provide an important basis for the study East China stratum settlement model and water management. INTRODUCTION Ground-surface subsidence is a common geological disaster, which has the features of continuous, changing slowly, concealment (Y.P. Yin et al. 2005). Today, due to underground mining and constructions in formation compression, surface subsidence is wide-spread in the world, which is the environmental geological problems in the worldwide that cannot be ignored (Y.Q. Xu et al. 2006, D.L Gallo-way et al. 2000, Qiu, B. et al. 2011). The eastern region of China has generally geological disasters in coal mine geological caused by the thick loose layer settlement like as mine shaft failure. Stratum dehydration consolidation is a major cause of loose layer settlement (H.Y .Liu et al. 2007). A method of water injection using ground water to stable water level is proposed, which can effectively control the loose layer caused by compression settlement(J. Chai et al. 2012&.2013). Accurately knowledge the characteristics of strata deformation is the premise of settlement management (Q.C. He et al. 2006). Previous re-search (J.F. Miu et al. 1996, X.Y. Gu et al.1998, Y. Zhang et al. 2006), mainly studies are focused condition of the city pumping irrigation, de-formation characteristics of middle and up loose layers. On a group of aquifer in East China, the loose layer losing water is caused by coal mining, bottom water drainage and overlying strata water flowing fractured zone hydrophobic induced by mining, which the dehydration conditions have great difference from one to another. The Position of water loss is centralized in bottom aquifer, and the formers of ground subsidence geological environment and settlement mechanism are different. According to the study of stratum settlement, usually the de-formation of sand layer is ignored(C.H. Liu et al. 2004), but few studies show that the sand layer have the plastic deformation, and contains the creep deformation, water content of sand soil may become the main settlement layer (Z.X. Wei, 2002, C.H. Liu et al. 2004)."

Jan 1, 2015

By Alexander N. Winchell

"Location: The Menominee district has been described geologically in several units, because the known iron-bearing formations of the larger region are not a really connected. From the commercial and mining standpoint, however, the district em¬braces, all that territory extending from a point about five miles east of Vulcan to a point a few miles west of Iron River, an east-west distance of about fifty miles, and from a line about two miles south of Vulcan to one ten miles north of Crystal Falls, a north-south distance of about thirty-five miles. This area is largely in the State of Michigan, but includes more than two hundred square miles in Florence County, Wisconsin. The chief towns of the district are Vulcan, Iron Mountain, Iron River, and Crystal Falls, in Michigan, and . Florence in Wisconsin. The Wisconsin portion of the district has not produced a large portion of the output of the area.History: The earliest reports of iron ore in the Menominee district were made by J. W. Foster and S. W. Hill, who conducted a geological exploration from Lake Superior to Green Bay in the fall of 1848. It is a remarkable fact that in spite of their plain statements regarding their discoveries, these state¬ments were apparently forgotten for a period of nearly twenty years. Foster states that ""about two miles southeast of the lower falls (of the Twin Falls on the Menominee River) near Sec. 30, T. 40 N., R. 30 W. there is a large bed of specular iron ore associated with the talcose and argillaceous slates. It makes its appearance on the north side of the Lake and can be traced a mile and a half in length and in places is exposed one hundred feet in width."""

Jan 1, 1920

By Cloyd D. McDowell

The Federal coal Mine Health and Safety Act of 1969 has been criticized by those who say it goes too far in controlling the activity of private enterprise and by those who say it does not go far enough in eliminating fatalities and accidents in an accident prone industry. Possibly a better evaluation of this legislation lies somewhere in between. From the viewpoint of the coal industry it can be said that through the efforts of those engaged in mining, both the operator and the miner, the year 1969 marked a record year in mine safety with only 190 fatalities and a frequency of 0.84 per million man hours exposure. This outstanding achievement compared to any previous was the result of a determined effort on the part of a concerned industry to improve its reputation as being the most hazardous industry in the nation. After the effective date of the Act, March 31, 1970, the Bureau of Mines assumed complete control of all safety and health activities of the mining industry. Unfortunately, there was no improvement in the safety record of underground mines in 1970 with the total of 255 fatal injuries and a frequency of 1.04 for the year. The number of fatalities declined to 177 in 1971 but the number of underground coal mines had declined from 5,955 to 2,268 during the two year period. Meanwhile, surface mined coal increased from about 38% of total production in 1969 to over 50% in 1971, keeping the annual production of coal at a normal level but involving fewer men.

Jan 1, 1973

By S. K. Kawatra, J. E. D. McDonald, S. C. Roache

"The formation of geopolymers from mine tailings using cold-bonding processes is known to be possible. Numerous cold-bonding methods exist, but the hydrothermal processes involving high temperatures and pressures in the presence of steam have been found to be the most ideal. This paper presents the results of successful preliminary studies to apply hydrothermal bonding processes to mine tailings agglomerates. Particle-size analysis revealed the particle size of the tailings waste to be 80 percent passing at 35 µm. The compressive strengths of the tailings pellets were shown to increase with time in the curing vessel, closely approaching the 400 lbf of standard iron ore concentrate pellets. These strengths are sufficient to allow use of the tailings pellets as aggregate materials for asphalt and cement. Additional applications may be possible, including reprocessing to extract more valuable materials and usage as agglomerated road-bed materials, backfills for building foundations, and replacements for sand and lime in cement.IntroductionMine tailings are a waste byproduct of ore concentration and are available in large quantities across the world. Despite their abundance, they have received little attention or consideration for beneficial use. One reason is that the chemical nature of the material is not well known. Another factor that has hindered direct usage is the fine particle size. This raises the questions: what is the composition of the tailings, and how can such fine solids be beneficially used? Because the mining industry produces concentrates, the tailings may be treated as concentrates and processed in the same fashion, but it would be inefficient to consider full sintering or induration conditions for materials that have little ore content. To achieve sustainable operation, the development of technologies to use these tailings is necessary. Mine tailings should not be considered waste, and an “out of sight, out of mind” mentality does not represent a sustainable solution for the future.One iron ore mine in Michigan is estimated to have accumulated more than 400 million metric tons of tailings during its last 30 years of operation, with an additional 180 million metric tons accumulated before the ore body is depleted. These mine tailings currently have no practical use, largely due to a scarcity of knowledge of their true physiochemical nature. It is thought that lack of quality control of the waste material prevents its use, but variability in the unprocessed ore prevents a consistent waste stream composition. The fact that the tailings are available in such great quantities makes them an extremely attractive resource. However, developing a sustainable, low-cost means of repurposing the mine tailings waste as a construction material may only be completed once the tailings are physically and chemically understood. Due to the high silica content of the material studied, cold bonding was determined to be the most viable method for processing the tailings into a usable product."

Jan 1, 2016

By K. Bunney

A high-pressure laboratory elution rig was commissioned to simulate industrial Zadra and AARL elution conditions for the stripping of gold, silver and mercury from loaded activated carbon. It was found that cyanide was essential for the efficient elution of both mercury and silver, while gold was found to elute most effectively in hot, low-ionic strength solutions. Therefore, the standard AARL-type elution, which implements a cyanide soak and water elution, results in a lower recovery of mercury and silver from the carbon. No single set of conditions was found whereby gold, silver and mercury can all be effectively eluted in a single step. However, sequential elution conditions can efficiently recover all metals and provide a potential approach for separating these metals.

Jan 1, 2010

By J. D. Miller, C. L. Lin, J. Dong

Nano clay mineral particles such as kaolinite — with primary particles typically smaller than 2 μm in size — can cause significant problems in flotation processes and tailings disposal, including the processing of Florida phosphate rock and Canadian oil sands. In this study, the consolidated state of flocculated kaolinite sediment was examined, and high-resolution X-ray microtomography (HRXMT) was applied to describe the structure of the consolidated sediment. Using this tomographic information, the complex geometry of the channel network structure for the consolidated flocs was established for the first time. With the establishment of the experimental channel network structure, permeabilities were estimated by flow simulation using the Lattice Boltzmann method. Results for kaolinite sediment with and without polymer are compared and discussed. Results for flocculated kaolinite sediment in a gravitational field are also presented and discussed. The results show that as polymer dosage increases, the permeability of flocculated kaolinite sediment increases, and as suspension pH increases, the permeability of flocculated kaolinite sediment decreases.

By Godfred Amponsah, Mehrdad Razavi

Slope failures very commonly occur during a long period of heavy rainfall and groundwater rise. The failures pose a substantial risk to people, infrastructure, and equipment downslope. In the recent past, the mining industry has faced an increase in tailings dam failure due to several reasons including pore pressure increases in the dams. Many failures have been observed to occur during times of water level fluctuations but the critical factors that influence the initiation of slope failures still need to be adequately clarified. To investigate these factors, laboratory experiments were conducted on model sandy slopes to determine pore pressure-induced slope failure initiation. This study also presents a method to examine water seepage through soil slopes using an ultraviolet (UV) dye and a UV flashlight. The small-scale model test simulation demonstrated failures induced by either water percolation from the upslope tank at a constant level or by raising the water level at intervals. A bottom chamber fully filled with water to replicate groundwater rise was also simulated. The soil slope was monitored at every stage to study the deformations and behavior until failure occurred. Results gathered from the controlled laboratory conditions were useful for the verification of the numerical modeling method created in the computer program Slide. The analysis showed that slope failure always occurred when the toe was fully saturated. High pore pressures and seepage forces reduce the shear force at the toe to almost zero causing it to slide. A comparison of slope height to water level also indicated an average of 96% water level to cause a failure. At this point, the soil slope is fully saturated and has no matric suction. The findings in this study show that, by monitoring the moisture content of slopes, failures can be predicted.

Feb 1, 2024

By C. E. Golson

Modern concrete technology emphasizes the basic qualities required of an acceptable aggregate: it must be clean, sound, homogeneous, and of a size gradation resulting in a concrete of the desired physical qualities at a minimum cost. In the case of coarse aggregates, crushing, scrubbing, and screening will usually provide the required material, although beneficiation is often necessary in order to eliminate unsound or deleterious fractions. Beneficiation is also applicable to fine aggregates,( but the processes most often employed are washing, classification, and dewatering.

Jan 1, 1959

By David Harrison

Exxon Minerals Company uses geostatistical techniques for ore resource evaluation of its mineral projects. These techniques provide the most reliable estimates of recoverable tonnage and grade and uniform and realistic confidence limits. A schema has been developed which categorizes the company's successive evaluation phases. Clear separation is intended between geostatistical estimates and other factors in project evaluation such as mining, metallurgy, and economics. Company management seeks consistent and reliable estimates for investment decision-making and to meet growing demands for disclosure of mineral assets.

Jan 1, 1983

By B. Gorain

"INTRODUCTION The last few decades have seen some remarkable advancement in information technology, but recently various digital technologies have resulted in several synergies to deliver innovation in diverse applications. The mining industry has been relatively slow in adopting these technologies compared to the other industries, but this scenario is changing fast. Keywords: Digital Transformation, Operational Intelligence, Gold Recovery, Mine to Mill integration, Planning and Execution strategy, Theory of Constraints. Challenges Mining companies globally are going through a series of challenges such as declining ore grades with complex metallurgy, increasing depth of ore bodies, high capital and operating costs, lower productivity, shortage of technical resources, significant pressure from stake-holders to deliver, along with growing environmental and corporate social responsibility issues. Improvement in profitability would need significant improvements in operational performance. Consequently, over the last few years, there has been a major focus amongst some mining companies to imbibe Operational Excellence. This has been only possible because of the replacement of a silos based approach by an integrated view of the organization. Such an integrated view is now possible via the evolving digital technologies. Even so, such a transformation calls for a change in culture, which, for most organization is not trivial. Attempts in the past to integrate functions such as through Mine-to-Mill initiatives in the mining industry have demonstrated significant benefits to many operations (McKee, 2013). Still, sustaining these benefits has clearly been a challenge due to manpower turn over and lack of proper systems and structures that integrate information between business functions within an operation and between operations and the corporate.Opportunities The advent of digital technology has opened-up opportunities to integrate inter-departmental information for a unified understanding of, and across, an entire organization. The advances in instrumentation, equipment control systems, supervisory control systems (SCADA/Historian) and industrial networks have helped in the direction of enterprise wide integration. The availability of real time information across an enterprise has given rise to numerous possibilities to improve organization performance. As suggested by Seshan & Gorain (2016), some of the potential opportunities are as follows:"

Jan 1, 2018

By Josh Swank

Albert Einstein once said, ?the important thing is not to stop questioning.? In the mining industry, a lack of inquisitiveness may lead to a blissful ignorance but it certainly will not increase efficiencies. While one may claim necessity is the mother of invention, questioning and analyzing how methods and systems can be improved is the catalyst to discovering necessities. Understandably, when working in the middle of Canada?s oil sands, where trucks operate around the clock every day of the year, it is nearly impossible to pull the nose from the grindstone long enough to provide thorough analysis. But, fortunately, some manufacturers/inventors have assisted by examining the process and the ensuing headaches within this application.

Jan 1, 2013

By Robert L. (Original by) Llewellyn

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment.

Jan 1, 1981

By Paul D. Tomlingson

The difficult and often harsh working environment of the mining industry can stress both personnel and equipment to the extreme. Often, the unintended consequences of this environment lead to confrontations between departments, as each goes about its tasks of mining, maintaining or supporting these activities. On occasion, the confrontations may result in criticism of other departments for perceived or real sins or omissions. The offended department may not be able to change the circumstances, but can only complain while frustration persists. The most effective solutions are the actions of the mine manager. By establishing mutually supporting roles of each department and specifying conditions for the interactive conduct of maintenance, the mine manager can better assure that the inherent problems of the mining environment are neutralized.

Jan 1, 2011

By Robert Smith

Deposits are global, said Barrick Gold's Smith. This means that the mineral industry, by necessity, is global. "Manufacturers have considerable freedom to decide exactly where they wish to produce whatever it is that they sell," he said. "What we sell, on the other hand, must be produced where nature chose to lay it down. The question is not so much, whether to go global, as when to do it and how to go about it." The timing of international expansion depends on external factors, often political, Smith said, and on internal ones that relate to the company's size and stage of development. "In deciding how to expand, a company is largely deciding how to adapt its existing business strategy to activity on the world stage," he said Barrick entered 1997 with 1.58 kt (51 million oz) of reserves, Smith said, annual production of 93.3 t (3 mil- lion oz) and cash flow of $463 million. Reserves in- creased 40% in 1996 and production will begin to rise again significantly in 1999. "We believe our fundamental strategy is responsible for our early development and subsequent success," he said. Barrick entered the gold-mining industry in 1983. Its corporate mandate was to create shareholder value, Smith said. From the beginning, the company took a different approach - businesslike, entrepreneurial, strategic and focused. "Many mining companies start out with a technical team and develop business and financial expertise thereafter," Smith said. "In 1983, Barrick had the business people, and then moved into mining." First, it acquired part interest in two small operations, one in Alaska and one in Ontario. Then, in 1984, it merged with Camflo Mines, which operated a low-cost underground operation in Quebec.

Jan 1, 1997

By C. R. McKee

In-situ mining of hard rock deposits will only become successful as we understand the engineering parameters involved and the design limitations they impose. As recognized by Wadsworth1 the most critical area is the enhancement of permeability in a hard rock mass. Along with creating permeability, the appropriate flow and fragment size conditions must be generated to insure economic rates of mineral recovery. In this article our interest is confined to true in-situ processes in which boreholes are drilled from the ground surface or a mine drift to deeper strata. We assume that fractures and permeability enhancement will be due to explosives detonated in boreholes. Other techniques such as hydraulic fracturing do not produce the necessary size distribution to promote economic extract ion rates unless the medium is already highly fractured and interconnected. Notable exceptions where hydraulic fracturing is applicable are many oil, gas and salt deposits. For many in-situ processes, an array of explosive charges offers the opportunity of creating a distribution of many fractures not achievable by other techniques. Such a situation would be suitable, for example, to in-situ mine hard rock gold, uranium, copper or oil shale deposits and may enhance oil and gas recovery in certain situations. The purpose of our article is to review and extend the explosive permeability theory of McKee and Hanson 3,4,5 and to apply its results to derive design parameters suitable for in-situ mining.

Jan 1, 1981

By William A. Wallace

Common mineral resources (sand, gravel, crushed stone, etc.), which are so necessary for the construction of metropolitan areas, are rapidly being depleted or otherwise rendered unavailable in the very areas that need them most. However, the problem of planning for these resources involves a number of independent and dependent variables that must first be defined and related. Finally, a dollar value must be assigned where possible. Complex interrelationships between the variables and their dependence on outside factors has made mathematical "solution" of the problem of planning for non-renewable mineral resources difficult at the present time. Therefore, the use of computer simulation is suggested as a means by which this complex problem can be investigated. The purpose of this paper is to report on a continuing research program whose objectives are: (1) to delineate the factors involved in planning for the utilization of common mineral resources in urban-suburban environs; (2) to construct a planning model for these materials amenable to computer analysis, (3) evaluate the model by using test cases, and (4) perform a sensitivity analysis to determine the initial parameters in future planning for these materials.

Jan 1, 1968

By W. E. Bardelmeier

The high speed conveyor type self unloading bulk carrier concept has been around for about 70 years. Although the design was developed, refined and steadily improved in the Great Lakes, to date limited numbers of such vessels have emerged in the bulk ocean trades, and these have tended to concentrate within specific mineral trades. For example, North American gypsum companies have embraced conveyor self unloaders to the point where such vessels almost exclusively carry the gypsum requirements of this part of the world. One major aluminum company has developed an impressive fleet capability in self unloaders. Application of other ships tends to be fragmented through several mineral trades. A few years ago a new phenomonen began to appear on the Great Lakes. Whereas it had historically been accepted in that region that self unloaders were effective vessels for the minor bulk trades including limestone, coal, salt, gravel and sand; they had seldom been employed heavily in the big volume iron ore trades. Suddenly, however, the new generation of 60,000 ton Lakers which emerged were all designed as high speed self unloaders. The new vessels intended to trade especially in ore, or alternatively especially in coal, have somewhat different internal features, but the important point is that all are self unloaders.

Jan 1, 1979

By S. Klein, M. McLeod, K. Johnson

The East Bay Municipal Utility District (EBMUD) delivers water to the San Francisco Bay Area through an aqueduct system extending from the Sierra Nevada Mountains to the East Bay. This aqueduct system, the Mokelumne Aqueducts, are comprised of three 82-mile long steel pipelines. The portion of the aqueducts crossing the Sacramento-San Joaquin River Delta is recognized to be vulnerable to seismic and flooding hazards. Previous studies evaluated alternatives for mitigating these hazards and increasing the reliability of the aqueducts for the next 100 years. The preferred solution involves construction of a 16.5-mile tunnel across the Delta and re-routing the existing aqueducts through this tunnel

Dec 1, 2022

By L. Alagha, J. L. Corchado-Albelo

To address the U.S. Department of Energy’s critical minerals strategies regarding rare earth elements (REE) in the U.S.A. This study evaluated apatite-rich mine tailing from the historic Pea Ridge Iron Mine (PR) for possible enrichment of REE by the froth flotation process. Comprehensive characterization studies were performed on the tailing samples to quantify the REE content, identify the REEbearing minerals and their liberation behavior. The aforementioned characterization studies were: x-ray fluorescence analysis (XRF), inductively coupled plasma mass spectrometry (ICP-MS), and TESCAN’s Integrated Mineral Analysis (TIMA). The ICP-MS analysis showed that the concentrations of heavy-REE and light-REE were 8000 ppm and 3000 ppm, respectively. TIMA showed that monazite was the major REE-bearing mineral. Additionally, it was shown that monazite and other REE-bearing minerals were strongly locked within larger apatite grains. Findings from the characterization studies suggested that REE could be enriched using phosphate minerals’ direct froth flotation process. Flotation feasibility tests were performed using selected organic and inorganic iron oxides’ depressants, including polyacrylamide (PAM), in-house synthesized hybrid polyacrylamide (HyPAM), chitosan, sodium silicates, and corn starch. Results showed that the depressant’s efficiency at pH 9 was in the following order: HyPAM > chitosan > PAM > sodium metasilicate > corn starch. Zeta potential studies on the selected depressants indicated that chitosan had the highest adsorption on magnetite’s surface at pH 7. Therefore, additional batch flotation experiments using chitosan as an iron oxides depressant were conducted as a function of chitosan dosage. Results indicated that the highest P2O5 recovery of 55% and grade of 28 wt.% were obtained at 150g/t of chitosan. However, the concentrate’s highest total REE enrichment of 1.07% was achieved at a 200 g/t dosage of chitosan. The low enrichment of REE highlighted the complex mineralogy of the PR tailings and the need to implement additional beneficiation strategies before and after the froth flotation process.

Mar 2, 2022