Search Documents

Traction of mining vehicles is well understood for a variety of unfrozen road surfaces, allowing optimal design of mine access and haulage roads. However, no such characterizations exist for the frozen or partially frozen surfaces typically encountered in Northern regions. Recent work by U. S. Army researchers suggests methods for characterizing roadway traction for any vehicle on the basis of test measurements made with a standard test vehicle. Such a test vehicle was designed, and several sets of test data were recorded at the onset of winter in Fairbanks, Alaska. This work suggests methods for future research and possibilities for the use of such research in designing drive systems, tires, and mine roads for Arctic and sub-Arctic mines.

Jan 1, 1995

By ?. ?ivkovic

The silicate slag and copper matte that are the byproducts of smelting copper in a reverberatory furnace contain SiO2, FeO, Fe3O4, CaO and Al2O3, and Cu, Fe and S, respectively. These components influence the oxide (Cuox), sulfide (Cusul) and total (Cutotal) copper content lost in the waste slag. This paper uses multiple linear regression analysis (MLRA) to determine the degree of influence. The results of calculations obtained using MLRA were compared to actual measured results and found to have a large degree of correspondence, with the coefficient of determination R2 = 0.975. These results indicate that slag composition and copper content in the matte influence the copper losses in the waste slag with a probability of above 97%. It was determined that, of the total copper content of the slag, 74% is in sulfide and 26% in oxide form, and that this ratio is not dependent on the slag or matte composition.

Jan 1, 2010

By R. R. Klimpel

This paper describes a series of mechanical flotation cell results run with various chemical reagent schemes designed to economically improve the flotation performance associated with selected industrially available coals. The emphasis is on the identification of practical flotation methods of processing coals containing unusually coarse and/or fine feed sizes, of increasing the recovery of oxidized and/or difficult to float coal, and of increasing the selectivity of coal over pyrite in high sulfur coals.

Jan 1, 1991

By Robert E. Blackett

To help local governments plan for long-term supplies of sand and gravel for buildings and infrastructure, the Utah Geological Survey is assessing natural aggregate resources (mainly sand and gravel) in the St. George, Utah area. Whereas much of the aggregate in the study area is adequate for road-base construction, high-quality aggregate for Port- land cement concrete is limited due to geology, and also due to land administration and environmental issues. Virgin River alluvial gravels southwest of St. George are generally poor sources of aggregate because they contain clasts of soft sediments and soluble minerals derived from Mesozoic rocks. Elsewhere, widespread secondary calcium carbonate (caliche), as rinds and matrix in gravel, lower the quality of material. Young river-terrace deposits in Fort Pearce Wash, and along the Virgin River above St. George are the primary sources of sand and gravel for the area. Alluvial fans on the east side of the Beaver Dam Mountains, and on the west side of the Hurricane Cliffs are also sources of aggregate. Stream-channel deposits associated with "inverted valleys" north of the towns of St. George and Hurricane, Utah, and older pediment gravels on the west flank of the Beaver Dam Mountains may be future sources of high-quality aggregate. Accelerated urban development during the 1980s and early 1990s has caused St. George and other communities in Washington County to encroach upon sand and gravel pits originally located in rural, undeveloped areas. Urban residents often view nearby sand and gravel operations as undesirable neighbors and pressure elected officials to close the pits. Pit closures effectively eliminate the remaining reserve from the sand and gravel resource base of the area. More- over, resources may also be lost as new homes are built upon undeveloped sand and gravel deposits. The St. George area is particularly susceptible to loss of aggregate resources because high-quality natural aggregate for construction is already in short supply. Moreover, most of the land in the study area is administered by the U.S. Bureau of Land Management and subject to various land-use restrictions. Much of this public land cannot be developed for mineral materials, such as sand and gravel, because of federal regulations protecting rare plants and animals, archaeological sites, and important watershed areas. Of particular concern to resource development are areas designated as Areas of Critical Environmental Concern, Wilderness Areas, and Wilderness Study Areas. Protection for Endangered Species is a critical element in all planning efforts. Those species present in the St. George area or in areas near- by include: the desert tortoise, southwestern willow flycatcher, Virgin River chub, and dwarf bearclaw poppy. As the St. George area is depleted and/or deprived of sand and gravel resources through extraction and urbanization respectively, construction costs will rise unless conservation measures are instituted. To avoid the loss of aggregate resources, the UGS is pursuing a program of data gathering and field surveying of surficial deposits to determine tonnage and quality of the remaining sand and gravel resources. The resource information from this program will help land planners, developers, and government officials make informed decisions concerning urban development throughout the region.

Jan 1, 2001

By J. P. Kennedy

Process data managers or historians are recognized as essential for reengineering projects in industrial plants. With increasing automatic data collection, the knowledge of how to use these data profitably grows as well. This paper is a summary of the data historian and its components plus examples of benefits including environmental reporting, performance monitoring, and exception reporting to management.

Jan 1, 1994

By Yuting Xue, Mark Van Dyke, Joe Wickline

The understanding of coal mine roof lithology is a critical component in the determination of engineering solutions for roof control. Coreholes were the first technology available to determine lithology of the roof in reserve areas, but coreholes are typically drilled 500–2,500 ft apart due to their cost and sometimes reach more than $125,000 dollars per hole, depending on mine conditions. The next method developed to bridge this gap was the fiber-optic scope which is utilized in the roof at the faces of underground development. High-end fiber-optic scopes can also be costly (20,000–40,000 dollars) but are more affordable than drilling a corehole, and the information can be processed immediately to make quick roof support determinations. The fiberscope can be operated wherever a roof bolter can drill a hole, and there are no restrictions related to property owners, proximity to streams, elevation changes, etc. The latest borescoping method utilized by mining companies is the use of videoscopes. Videoscopes and all borescopes in general are limited by the lengths of the scope and the length of the borehole drilled in the mine. Videoscopes have the advantage of being able to record video while examining the roof lithology. The information can be recorded quickly underground and then be examined on the surface which allows anyone to capture the video so that a geologist can make lithology descriptions without ever going underground. In the past, videoscopes had limited resolution, a short battery life, were fragile and were relatively costly. As technology progresses, videoscopes have become more affordable, have increased battery life, and offer enhanced 1080p resolution. With the broader availability of affordable videoscopes, videoscopes can be more readily used in various mine environments at every active section underground. This paper will discuss the types of videoscopes available, the features that will aid in lithology description/identification, the deployment methods pertaining to supplemental roof support recommendations, and an advanced methodology to enhance accuracy in understanding roof lithology.

Feb 1, 2025

By D. S. Flett

Abstract. The commercial importance of hydroxyoximes as extractants for copper has given impetus to basic studies on the chemistry of metal extraction by these compounds. The discovery of accelerator compounds which produce catalytic effects on hydroxyoxime extraction rates has led to mechanistic studies of these rate processes. While these studies have highlighted the importance of interfacial chemical reactions in the extraction process, it is not yet possible to unambiguously describe the mechanisms of metal extraction in these systems or the associated catalytic effects. This paper reviews progress in understanding the mechanism of metal extraction by hydroxyoximes.

Jan 1, 1979

By S. P. Fleming

An acid mine drainage sludge containing 0.26% nickel, 0.21 % cobalt and 4.5% manganese was leached in a one-liter reactor with sulfuric acid in the absence and presence of sodium sulfite. The effects of temperature (25°C and 52°C) and sodium sulfite concentration (up to 0.03 molar) on the leaching rate were particularly investigated. The leaching rates of nickel and cobalt with sulfuric acid have been determined to be controlled by diffusion through product layer. It has been found that effective leaching conditions to give more than 90% extraction of nickel, cobalt and manganese while keeping the iron extraction below 10% come with an elevated temperature and a low sodium sulfite concentration at pH 3; for example, 52°C and 0.01 molar sodium sulfite.

Jan 1, 1992

By P. J. Ryan

Phelps Dodge’s Candelaria copper-gold mine is located 20 km (12miles) south of Copiapó in northern Chile’s Atacama province (Region III) (Fig. 1). The Candelaria Mine is about 800 km (500miles) north of Santiago and 75 km (47 miles) east of the Pacific Ocean. Its elevation is 600 m (1,970 ft) above sea level. The Copiapó River Valley is 6 km (4 miles) northeast of the mine site. It is the only major source of water in this arid region. The average rainfall is 14mm/a (0.5 in./year). During 1995, the mine produced 521.4 kt (574,800 st) of copper concentrate containing 150 kt (165,000 st) of salable copper and 3 t (98,800 oz) of gold. The 1995 unit cash cost was less than 50 cents/lb of copper. This makes Candelaria one the world’s lowest cost copper producers.

Jan 1, 1996

By R. B. Tippin

Great Salt Lake Minerals & Chemicals Corporation (GSL), a subsidiary of Gulf Resources & Chemical Corporation, is located on the east side of the Great Salt Lake, approximately 20 miles from Ogden, Utah. GSL processes brine from the north arm of the lake to produce potash, salt cake, salt and magnesium chloride brine. Potash fertilizer, in the form of K2SO4 is GSL's primary product. The GSL Sulfate of Potash Complex The GSL potash complex (depicted in Figure I) is divided into a solar evaporation pond system and the process plants. The solar,evaporation system consists of a 17,000-acre (68.8 Km2) ponding operation where the various salts deposit during the summer evaporation season, and a harvesting operation which recovers the deposits during the remainder of the year. The harvest is either preconcentrated in the flotation plant or processed directly in the chemical plant where sulfate of potash (SOP) is produced. The chemistry of the lake brine results in a solar deposit con¬taining primarily kainite (KCl-MgSO4.3H20), schoenite (K2SO4?MgSO4^ 6H2O), and halite (NaCI), with some carnallite (KCl.MgCl2.6H20) and epsomite (MgSO4.7H20). Other minor minerals may be deposited, depending upon the weather during the evaporation season. Each year, the solar deposit in the evaporation ponds will greatly depend upon the summer weather conditions, which have in the past proven to be quite unpredictable. Weather may alter both the quantity of the solar deposit and the composition of this deposit. During, a "short" evaporation season, the tonnage deposited decreases, but depending upon the short-term weather, the potash mineral content

Jan 1, 1977

By Lawrence L. Davis

This paper describes current research by the Bureau of Mines to develop technology for improving efficiency and productivity in metal/ nonmetal mines. The research program addresses a wide variety of problems associated with each of the major categories of mining: underground mining, surface mining, in situ mining, and premining investigations. An overview of the Bureau's research activities is given with emphasis on underground mining. In particular, two innovative and promising concepts currently under development are described: a unique shaft sinking system that uses an impact hammer for rock fragmentation, and a low-profile, portable crusher for underground hard-rock applications.

Jan 1, 1979

By K. Avarmaa, P. Taskinen

"The solubilities of rhodium (Rh) in a molten silver alloy in doré-smelting conditions for treating copper refinery slime at temperatures of 1,000 to 1,300 °C were measured using a high-temperature equilibration-quenching technique and direct phase analysis by electron probe X-ray microanalysis. The results obtained indicate that the solubility of rhodium in molten silver is very limited: only 0.04 to 0.26 weight percent at 1,000 and 1,300 °C, respectively. The thermodynamic properties of rhodium in molten silver were estimated from the solubility data. The compositions of the solid rhodium alloys in equilibrium with molten silver-rich doré metal were also measured in this study. The excess rhodium in the doré alloy will precipitate during the refining as solid, greater than 99 weight percent Rh.IntroductionSilver refining is a core step of the processes of anode slime treatment and precious metals recovery in copper refineries (Hait, Jana and Sanyal, 2009; Ludvigsson and Larsson, 2003). It separates the oxidic materials, such as nickel oxide (NiO) and barium sulfate (BaSO4), from metallics after the de-coppering and de-selenation steps of the anode slime, and refines the silver bullion from the undesired elements present (Cooper, 1990; Hyvärinen, Lindroos and Yllö, 1989). Doré metal is a silver-rich alloy which after the smelting step will be refined electrolytically, and the remaining constituents of gold as well as the platinum group metals (PGM) will be subsequently recovered in their own processing stages.Because of low concentrations of PGMs in copper, they are typically soluble in the doré metal in anode slime treatment. This can be concluded from their binary phase diagram data with silver (Massalski et al., 2007). One exception is sometimes encountered in the anode slime smelting operations if the smelter feedstock is rich in rhodium, as may be the case if the raw materials contain secondary raw materials such as e-scrap. The solubility of rhodium in solid silver is less than 0.04 weight percent (Królas and Sternik, 1995), and its solubility in molten silver is highly uncertain. The only experimental information in the literature (Królas et al., 1993; Elliott, 1985) suggests that the silver-rhodium alloy system at 960 °C forms a eutectic, which locates less than 2 °C below the melting point of pure silver (Arblaster, 2015). Early observations (Rössler, 1900) propose that rhodium is insoluble in molten silver even if solid silver-rhodium solutions have been recently produced on a nanoscale (Kusada et al., 2010).The aim of this study is to measure experimentally the solubility of rhodium in molten silver at doré metal smelting and refining temperatures. The silver alloy used to mimic the doré alloy contained silver and about 1 weight percent of the alloying elements copper, gold, palladium, rhodium and tellurium. The experiments were carried out in metal-slag equilibria with nitrogen-oxygen mixtures as the atmosphere, employing an equilibration-quenching technique and using direct phase composition analysis by electron probe X-ray microanalysis (EPMA) (Jak, Hayes and Lee, 1995)."

Jan 1, 2017

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

By Kwangmin Kim, Junnhyeok Park

In the hard-rock mining industry, the generation of fines during blasting is an important issue because it has a significant effect on production processes. Although various approaches have been used to estimate fines generation in recent decades, as a practical matter, measuring the amount of fines is nearly impossible given the technical limitations and the scale of mine blasts. In this study, a dynamic PPV damagemodel was developed and applied to predict fines generation as a result of blasting. This modified version of the crushed zone model (CZM) considers dynamic rock properties and peak particle velocity (PPV), which represents the induced stress in blasting. Dynamic rock-fracturing tests were conducted using a split Hopkinson pressure bar (SHPB) to determine the parameters that represent the relationships between rock strength and strain rate as well as the relationships between fines amount and strain rate in the model. A case study was conducted that entailed determining the radius of the crushed zone for given blast designs and rock properties and then measuring the fines amount within this crushed zone. This case study indicated that the dynamic PPV model can provide a rough estimate of fines generation for given dynamic rock properties and blast design parameters and that this method has the potential to be a useful indicator, or index, of fines generation.

May 16, 2020

By Michael J. Beus, Jan G. Patricio

INTRODUCTION The U.S. Bureau of Mines, Spokane Mining Research Center, has been conducting and documenting rock mechanics research in the Coeur d’Alene mining district for the past ten years (1, 2, 3, 4, 14, 15). A current project combines the information gathered from rock mechanics instrumentation, geologic structure, and analytic techniques to improve shaft and support design for the deep mines of the district (3). This project required knowledge of the anticipated loads and the physical properties of the rock mass to provide accurate input data for computer design models. Several techniques have been utilized to determine the physical parameters including the USGS (U.S. Geological Survey) solid inclusion probe, the CSIR (Council for Scientific and Industrial Research) biaxial and triaxial strain cells, and the CSM (Colorado School of Mines) dilatometer. This paper describes the determination of the in situ modulus of deformation in three mines over a period of three years and the evaluation of these results as they applied to this project. The need for in-situ rock mass properties such as the modulus of deformation has stimulated research and development of a large number of instrumentation techniques. One area of continuing interest involves various methods of radial borehole dilation. This concept was pursued by Menard (9) with an apparatus known as the pressure meter, which is used frequently in soil mechanics. Other developments in rock mechanics include the CPC (cylindrical pressure cell) by Panek (11) and the dilatometer by Rocha et.al. (13) in Portugal. The CSM dilatometer, which also utilizes this technique, was chosen for this project because it required a small amount of background study, was inexpensive, and could easily be combined with other experiments being planned for the test locations. Although no previous field applications to hard rock (compressive strengths greater than 20,000 psi) has been documented, the instrument was selected since good results have been achieved in granite, oil shale, and several coal measure rocks (11, 12).

Jan 1, 1977

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents the preliminary test results obtained using a 0.38-kg/s (3,000-lb/hr) beta prototype MagMill. In processing Upper Freeport coal, the beta prototype recovered 82 % of the weight of the feed and 91 % of the heat content while reducing the potential emissions of sulfur by 61%. Pyritic sulfur in the MagMill product was reduced by 78% compared with that in the feed. For all runs, the mill product particle size was controlled to between 70% and 80% -741m (200 mesh). Recoveries of mercury, arsenic and selenium ranged from 35% to 45% of the amounts found in the feed. Power draw was reduced by 26%, and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2002

By B. V. Cooper

The word "research" has been used in the title of my presentation somewhat against my better judgement. There are many definitions of the word. But the one I like best comes from Webster's New World Dictionary. It reads: "Careful, systematic, patient study and investigation in some field of knowledge, undertaken to discover or establish facts or principles. ..." I like that. In only 9 words, the definition conveys to me the very essence of what should be going on either in or for the coal industry. Unfortunately, not enough coal-related research is going on. And much of what is being done is, in my view, not really as effective as it might be.

Jan 1, 1983

By Andrea B. Baldwin

In recent years, federal and state regulatory agencies have tightened air emission standards. Two of the acid gases, hydrochloric acid (HCI) and sulfur dioxide (SO2), are under heavy scrutiny for reduction. . Most traditional scrubbing systems, i.e. wet scrubbers and spray dryers, meet the standards but they typically are high in capital cost, have significant space requirements for equipment, and are difficult to maintain. Dry sodium injection (DSI) is a alternative technology that has been shown to be effective in HCl and SO2 removal while being the inverse to the problems listed with traditional systems. This paper covers the mechanics of dry injection scrubbing using the most effective sorbents, sodium bicarbonate and mechanically-refined trona (natural sodium sesquicarbonate). It presents DSI performance data for Chambers Medical located in Hampton, SC. This facility incinerates local medical and municipal solid waste. Chambers Medical has used mechanically-fined trona for HCl and SO2 removal since late 1991.

Jan 1, 1995

By E. Bakhtavar

It is considered that the most economical method for the exploitation of Gol-e-Gohar Area 3 iron ore mine is to combine open-pit and underground methods. In this regard, the most critical problem is the determination of optimal final pit depth. In this paper, a method which was recently introduced on the basis of economical block models of open-pit and underground is used to determine optimal final open-pit depth of Gol-e-Gohar Area 3 mine with due regards to the future underground mining option. Considering a low cost and productive underground method as a feasible alternative for extraction of the lower part of this deposit, room and pillar was selected. It is concluded that after the assessment and comparison of different values for depth, optimal final open-pit depth was determined to be equal to 285 m.

Jan 1, 2010

By V. Dentoni

The paper deals with the assessment of the visual impact generated by surface mining and quarrying. Previous research works proved the applicability of an indirect method based on the elaboration of digital images through which the extent of the visible altered area and the chromatic contrast with the surrounding environment is calculated. The resulting level of visual impact allows an objective comparison among different cases as far as the evaluation procedure is univocally defined. The article illustrates the application of the method to a number of selected quarries located within the Sardinian territory; different issues are discussed such as the choice of the viewpoints from which the pictures are taken, the influence of the distance from the quarry to the selected viewpoints, the light condition and the orientation of the quarry faces. Moreover, the visual impact level obtained from pictures taken at the same time with five digital cameras are compared in order to evaluate the contribution on the overall uncertainty.

Jan 1, 2008