Search Documents

By Chuang Sun, Feng Luo, Guo‑dong Li, Xue‑qing Li, Tuan He

The mining-induced failure of the coal seam floor is essential for water inrush. The mining disturbance to the floor, especially in the thick coal seam, is severe, and the water inrush risk is also higher than that in regular thick coal seam excavation. The superposition of many stresses, including in situ stress, mining-induced stress, and confined water pressure, must be considered in the prediction of the floor failure depth. This study adopted the elasticity analysis, FLAC3D numerical simulation, and on-site acoustic wave test comprehensively. The thick coal seam working face of the Zhong-Yu coal mine affected by confined water was selected as the engineering background to study the characteristics of the floor failure. Based on elastic foundation theory and the superposition principle, the mechanical model and the failure depth criterion of the floor were established, respectively. The distribution and evolution of mining-induced stress and the plastic zone in surrounding rock during the mining process are obtained by FLAC3D. In addition, the changes in the P-wave wave velocity in the floor before and after mining were compared and studied by the acoustic wave test method. The range of floor damage depth is determined on the basis of the above research.

Jun 8, 2022

By Thomas D. Boyce

Minewater from many western U.S. uranium mines often contains radioisotopes in concentrations higher than permissible for discharge to unrestricted areas. .Radium 226 has the lowest permissible concentrations of all radioisotopes and usually greatly exceeds this limit in untreated effluents. This radionuclide is derived from the natural radioactive decay of uranium: [ ] The treating of minewater effluents has been studied previously (1) and the classical removal method for radium has been adsorption on barytes or freshly precipitated barium sulfate. This paper describes the removal of radium from minewater by utilizing a selective complexer based on a crosslinked organic polymer matrix.

Jan 1, 1982

By Barton G. Stone

"Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole," (Baxter and Parks, 1939)."An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence, the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence."The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling."Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive." (McKinstry, et al., 1948).In an actual orebody, the accuracy of sampling depends not only on the number of samples but also on their proper distribution throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore, it is important to select the places in such a way that all parts of the orebody will be represented."

Jan 1, 2014

By John Marsden

Despite the recent pullback in metal and mineral prices, and the associated market adjustments, the mining industry is still facing a serious issue with the declining availability of graduate expertise. This is due to a combination of an aging workforce, retirements and retrenchments, coupled with a lack of suitably qualified graduates entering the workforce. The issue has certainly improved since 2004 when the industry picked up the rates of hiring graduate engineers and mining/mineral school enrollments picked up in response. This hiring effort has helped to cover the ?gap? years from about 1985-2000, when industry demand for graduates was particularly poor. However, the recent market pullback is likely to set back this progress, as recruitment and hiring wavers as a result of cost cutting measures and economic uncertainty. A key issue for the mining industry is how to ensure the survival and growth of relevant ?core? degree programs. Such programs include mining, metallurgical, mineral processing and geological engineering. The mining industry needs a healthy, high-level education program to ensure an adequate supply of appropriately qualified graduates for the mining industry. Two-thirds of the professionals entering the minerals industry who graduated within the past 40 years graduated prior to 1985. Since 1985, we have been living off the legacy of graduation classes from the mid-1970s and early 1980s. It is estimated that we have been producing graduates at approximately 40 to 50 percent of the sustaining rate since about 1985. Further growth in the domestic industry would increase graduate requirements significantly, and the export of U.S.-graduates to other parts of the world (as is currently occurring) also impacts the total graduate requirements.

By Kewal K. Kohli, Richard E. Thill, Syd S. Peng

The results of unpublished investigations into surface subsidence from coal mining in the Northern Appalachian Coalfield are summarized. These investigations were carried out by various coal companies and the State of Pennsylvania in the sixties and seventies. Subsidence data were collected and analyzed from 10 room-and-pillar panels in 5 mines in the Pittsburgh coal seam. Results show that angle of draw ranges from 26° to 33° and subsidence factor from 0.42 to 0.72; surface heating generally occurs beyond the edges of the panel, the amount and extent of which vary; waviness occurs in the subsidence profile if a substantial number of pillar stumps are left in irregular patterns; interpanel effect is significant; time-dependent subsidence exists, but varies for different panels; and surface slope does not seem to affect the amount of subsidence.

Jan 1, 1982

By I. D. Lindley

The Wild Dog vein gold deposit in East New Britain Province, Papua New Guinea, forms part of a recently discovered 26 km zone of auriferous quartz vein mineralisation. The deposit, which was discovered in July 1983, has no silt anomaly, and a panned concentrate anomaly and float train restricted to within 500 m and 800 m respectively, of the discovery outcrop. Discovery of the Wild Dog deposit was a result of the methodical followup of regional panning which, as followup progressed, was replaced in importance by float sampling. Of the sampling methods used during the exploration leading to discovery, panning and float followup provided immediate indications of the presence of mineralisation. This high degree of spontaneity of followup is not provided by geochemical techniques, and has obvious advantages in high cost exploration for precious metal deposits in remote locations.

Jan 1, 1988

By W. K. Connor, O&apos

The Bureau of Mines is investigating the Co and Mn resource of the West-Central Arkansas District, including field investigations, mineralogical characterization, beneficiation, and hydrometallurgical tests. The deposits occur within the Ouachita Mountains and are con-trolled structurally, occurring along the axes of anticlines making up the mountain ridges. Brecciated novaculite is cemented with a mixture of Mn oxides, primarily cryptomelane and psilome-lane. Cobalt is concentrated within a particular Mn oxide phase, lithiophorite. Chemical analyses on head samples reported up to 25 pct Mn and 0.17 pct Co. Magnetic separation yielded products with up to 41 pct Mn and 0.22 pct Co at recoveries of 95 pct Mn and 93 pct Co.

Jan 1, 1991

By E. McCullough

"Fostering positive community relations is a principal tenet of sustainable development, but conflict can test even the strongest of relationships. While conflict surrounding resource development projects has the potential to be destructive, it may actually pose opportunities for partnership and collaboration when managed effectively. It is therefore not only important for mineral resource professionals to recognize the financial and social costs associated with legal disputes among project stakeholders, but also for them to prioritize resolving social conflict using alternative channels that allow for win-win outcomes. A variety of dispute prevention and resolution techniques do exist, but successful practice is not yet the norm. Here we review the sources and consequences of social conflict in the context of mining projects, and discuss typical and alternative approaches to conflict management in light of their respective benefits and drawbacks. We also suggest implementation of conflict resolution lessons into resource-related university curricula as a critical step in the continued shift of the mining industry towards sustainable development. INTRODUCTION Social conflict is a recurring phenomenon in the human experience and serves as a critical mechanism for change [1-5]. It occurs when two or more parties perceive that their needs and interests are in direct competition with each other and believe they cannot be reasonably accommodated. Conflict over mineral resource activities, particularly the distribution of benefit and risk, has become an omnipresent issue throughout the world [6-7]. Contrary to common perception, however, conflict can be a positive, transformative encounter in some instances [2, 8-11]. For this to be possible, society and its acting agents must reconsider how to address conflict. What if conflict were only a challenge to try something different? It is well-understood that the mineral industries must manage an increasingly significant volume of social conflict [12-13], which can be a costly externality impacting all of whom are involved. Conflict is commonly considered in a two-party sense, but this can deeply over-simplify the true number of stakeholders. Besides mining companies and community members, government policymakers and regulators, public interest groups, and judicial systems, to name a few, bear the social expenses of poorly-managed conflict [4, 6, 12, 14-22]. It is desirable for interested parties to participate actively in a constructive way to pursue their needs rather than contributing to adversarial relationships, operational problems, and legal costs [1, 4, 12]. Some mining companies are of course already working to develop more productive relationships with their stakeholders, but there is undoubtedly still a gap between ideal and common practices. This gap can inhibit collaboration and threaten the potential for mutually-beneficial resolutions to complex social issues [12]."

Jan 1, 2016

By E. McCullough

"Fostering positive community relations is a principal tenet of sustainable development, but conflict can test even the strongest of relationships. While conflict surrounding resource development projects has the potential to be destructive, it may actually pose opportunities for partnership and collaboration when managed effectively. It is therefore not only important for mineral resource professionals to recognize the financial and social costs associated with legal disputes among project stakeholders, but also for them to prioritize resolving social conflict using alternative channels that allow for win-win outcomes. A variety of dispute prevention and resolution techniques do exist, but successful practice is not yet the norm. Here we review the sources and consequences of social conflict in the context of mining projects, and discuss typical and alternative approaches to conflict management in light of their respective benefits and drawbacks. We also suggest implementation of conflict resolution lessons into resource-related university curricula as a critical step in the continued shift of the mining industry towards sustainable development. INTRODUCTION Social conflict is a recurring phenomenon in the human experience and serves as a critical mechanism for change [1-5]. It occurs when two or more parties perceive that their needs and interests are in direct competition with each other and believe they cannot be reasonably accommodated. Conflict over mineral resource activities, particularly the distribution of benefit and risk, has become an omnipresent issue throughout the world [6-7]. Contrary to common perception, however, conflict can be a positive, transformative encounter in some instances [2, 8-11]. For this to be possible, society and its acting agents must reconsider how to address conflict. What if conflict were only a challenge to try something different? It is well-understood that the mineral industries must manage an increasingly significant volume of social conflict [12-13], which can be a costly externality impacting all of whom are involved. We commonly consider conflict in a two-party sense, but this deeply over-simplifies the true number of stakeholders. Besides mining companies and community members, government policymakers and regulators, public interest groups, and judicial systems, to name a few, bear the social expenses of poorly-managed conflict [4, 6, 12, 14-22]. It is desirable for interested parties to participate actively in a constructive way to pursue their needs rather than contributing to adversarial relationships, operational problems, and legal costs [1, 4, 12]. Some mining companies are of course already working to develop more productive relationships with their stakeholders, but there is undoubtedly still a gap between ideal and common practices. This gap can inhibit collaboration and threaten the potential for mutually-beneficial resolutions to complex social issues [12]."

Jan 1, 2016

By Ben Roderds

The Waneta Expansion Project (WAX) is located near the existing Waneta Dam site at the confluence of the Pend d?Oreille and Columbia rivers, approximately 10 km (6.2 miles) south of Trail, BC, Canada. The WAX owners consist of a partnership between Fortis Inc., Columbia Basin Trust and the Columbia Power Corp. This design-build project was awarded to SNC-Lavalin in late 2010 and is expected to be operational in mid-2015. The WAX consists of a new 335-MW powerhouse, including two new Francis turbine units, each generating approximately 167 MW. The powerhouse is located downstream of the existing Waneta Dam, and will make use of excess water that would otherwise be spilled during the runoff season. Water will be funneled to the turbines through an intake structure and two 10.5- m (34.5-ft) diameter, concrete-lined Penstock Tunnels. A 10-km (6.2-mile) transmission line will connect the powerhouse to existing electrical grids. Redpath/FKCI Waneta Tunnelers (RFK) was subcontracted by the heavy civil contractor, the Aecon/SNC Lavalin (ASL) joint venture, to excavate the two penstock tunnels and install the cast-in-place concrete liner. RFK is a joint venture partnership between J.S. Redpath Ltd., an underground mine contractor located in North Bay, Ontario, and Frontier-Kemper Constructors ULC, a heavy civil tunneling contractor based in Nova Scotia, Canada. Since penstock tunnel excavation was planned using drill-and-blast methods with a significant grade of more than 17 percent, the combined experience of these two contractors was a perfect match.

Mar 1, 2014

By J. H. Kempton, D. Atkins

Predictions of delayed environmental impacts from mining—degradation that won’t begin for hundreds of years, but will then continue for thousands—present new permitting challenges. Examples include evaporative concentration in pit lakes, which can eventually cause metals concentrations to exceed human and wildlife toxicity standards, and delayed degradation of groundwater by slow moisture percolation through acid-generating tailings and waste rock. Given the time-value of money, the present worth of such delayed impacts is insignificant, yet they are unacceptable undercurrent laws and cultural values. Long-term financial set-asides offer a possible solution, first funding infrequent, long-term monitoring, followed by more expensive mitigation when the set-aside has matured.

Jan 1, 2000

By Leo R. Love

A comprehensive study of the environmental conditions of the area affected by the Colfax and Cheswick Power Stations is of extreme importance to Duquesne Light Company. The residents in the valley where the two plants are located have complained for many years about the emissions from the Colfax Plant which is of the 1920 to 1930 vintage and which has a capability of generating approxi¬mately 200 Mw. They were extremely happy to hear that the Company had plans for shutting it down, however, they were extremely unhappy to hear that we were planning to build another even larger one to take its place in the same vicinity, namely the Cheswick Plant with a capability of 570 Mw. They had visions of a plant twice the size of the Colfax Plant and belching out twice as much smoke. A few of the citizens from that area were most vehement at the public hearings that were held by the Allegheny County Air Pollution Bureau for obtaining an installation permit. With two power plants already existing in that area (Duquesne Light Company's Colfax Plant and West Penn Power's Springdale Plant), the primary concern of the Allegheny County Air Pollution Control Bureau was that the Cheswick Station might increase air pollution levels beyond what they considered to be dangerous limits. It became very evident that the Allegheny County Air Pollution Control Bureau would be extremely reluctant to grant installation and operating permits unless they were satisfied that the new plant would not increase local pollution levels and that we were taking sufficient steps to monitor the emissions from our plants and also the ambient air in the general area. We concluded that an extensive air pollution monitoring program must be conducted in the area to determine the effects of the operation of our plants. The program was conceived with our consultants, NUS Corporation of Rockville, Maryland, and was begun in June, 1968. It was designed to accomplish several things: 1. Determine the effect on the ambient air of the operation of each of

Jan 1, 1972

By C. Xiao, R. Chi

In recent years, the biosolubilization of rock phosphates by phosphate-solubilizing microorganisms has become a major topic of research studies. However, the microorganisms used in previous studies were mostly single and known species, and studies seldom focused on mixed communities of microorganisms or microbial consortia from natural environments. In this study, a microbial consortium from rhizospheric soil was used to solubilize two different compositions of medium- to low-grade rock phosphates — designated as ore samples 1 and 2 — in a laboratory-scale bioreactor. The microbial consortium showed good growth in the bioreactor, reduced the suspension pH and released soluble phosphates from the ores. Scanning electron microscopy with energy-dispersive X-ray spectroscopy showed the action of the microbial consortium on the ore surface. There was considerable corrosion on the ore surface, and 3.42 and 4.93 percent of the element phosphorus was removed from ore samples 1 and 2, respectively. Microorganisms were sampled from the bioreactor for the analysis of their community structures by Illumina MiSeq high-throughput sequencing. The analysis show that the suspensions added with different ore samples had different microbial diversities and richness. This study provides new insight into the biosolubilization of rock phosphates by a microbial consortium directly taken from rhizospheric soils.

By Martha Gross, Amanda Wachenfeld, Brian Keaney, Jean-Michel Charpentier, Frank Perrone

The Hampton Roads Bridge-Tunnel (HRBT) Expansion widens the existing four-lane bridgetunnel corridor to eight lanes through construction of two parallel tunnels, interstate widening, and bridge expansions. As part of the design-build contract, a supplemental geotechnical investigation was completed to support the design. The investigation for the subaqueous tunnel segment consisted of over 48,400 linear feet of drilling and 7,100 laboratory tests. This paper discusses the challenges of planning and executing a large-scale geotechnical investigation for underground works in a marine environment and the use of big data for effectively managing, interpreting, and transmitting data to the design-builder consistently throughout the investigation.

Jun 23, 2024

By Nasser Madani, Yerbol Tussupbekov, Sergei Sabanov, Zarina Mukhamedyarova

A case study was conducted on a metal mine operating in Kazakhstan, in which problems were associated with use of a complicated and outdated ventilation system and its high expenses. The mine needs to reconsider its existing ventilation system and identify the risks associated with operational losses when using this ventilation system. The aim of this study was to develop an efficient risk analysis method capable of estimating operational risks and financial benefits of the existing mine ventilation system. The developed risk analysismethod considers ventilationmodelling, riskmodelling, and financialmodelling.Ventilation modelling comprises ventilation simulation and ventilation financial simulation. In risk modelling, the number of risk events occurring with the use of existing ventilation system and the operational losses during these events is estimated. Financial modelling considers operational losses and ventilation financial simulation benefits and uses a dynamic cash flow model to estimate how cost variability influences the cash flow. As a result, the improved ventilation system attains an additional NPVa ranging from 3.2 to 8.5 million US$ at the corresponding defined probability of 90%. The results of this study reveal that the developed risk analysis method can efficiently estimate the financial benefits of ventilation modelling and consider risk events and their total operational losses associated with use of the existing ventilation system. This approach provides a range of possible outcomes and helps with deciding whether the ventilation system is appropriate or whether it should be updated to better suit the project financial benefits.

Jun 3, 2020

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology (Le. stratification, turnover, and development of anoxic conditions with depth) of the lake. Limnologic data collected from four existing pit lakes indicate that pit lakes develop a thermocline, or temperature stratification, in the upper 10m to 30 m of the water column. Two of the pit lakes (26 m and 55 m deep) undergo seasonal turnover of the entire water column, whereas two deeper pit lakes (110 m and 240 m) undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column and a distinct chemocline develops with depth.

Jan 1, 1996

By J. Christophe Niyonzima, Ekata Emmanuel Edo, Sayaf Mustafa, Liqun Luo

Iron and manganese both are important ferrous metals, and they usually need to be extracted separately for better usage. Ferromanganese ore from the Yunnan Province of China was investigated by subjecting it to reduction roasting, leaching, magnetic separation, hydrometallurgical separation process, X-ray diffraction (XRD), electron probe micro-analysis (EPMA) and scanning electron microscopy/energy-dispersive spectroscopy (SEM-EDS). It is noted that the ferromanganese ore contains valuable components or elements of 21.41 wt%Fe2O3 and 19.88 wt%MnO, which are 14.99% and 15.40% of the total of Fe and Mn, respectively, with a large amount of impurities comprising 33.00 wt% SiO2, 9.81%wt%Al2O3, etc. After roasting, microscopic examination showed the presence of haematite, magnetite, pyrolusite, psilomelane, hollandite, marcasite, pyrite, limonite, braunite and manganite, while XRD analysis showed that the magnetite content increases with the increase in roasting temperature, reflecting the increase in conversion of haematite to magnetite. Based on EPMAand SEM-EDS analysis, it was shown that the haematite and magnetite interface were the main Fe-bearing minerals; however, the dissemination of the two minerals, that is, haematite andmagnetite with the coexistence of Fe- and Mn-bearing minerals, will result in difficulty in effective separation of Fe and Mn. The effective roasting temperature and roasting time were 800 °C and 60 min, respectively, to avoid the formation of a composite oxide of MnxFe3-xO4 beyond 800 °C. The Fe recovery via roasting and magnetic separation only was 66.56%, whereas a combination of magnetic separation which ensued after the leaching process showed a recovery of 80.08% and 59.95% of Fe and Mn, respectively.

Mar 26, 2021

By Zhenzhong Bian, Ruiyang Zhang, Xiaofeng Zhong, Zhangxuan Ning, Yuanping Zhang, Jie Lu, Airan Zhang

This study addressed the separation and recovery of vanadium(IV), iron, and titanium from synthetic and real leach solutions of vanadium-bearing titanomagnetite using extractant P204 (di-(2-ethylhexyl) phosphate) and P507 (2-ethylhexyl hydrogen- 2-ethylhexyl phosphonate). Based on the speciation analysis of vanadium in sulfuric acid medium, the single-stage extraction efficiency of vanadium, iron, and titanium was 94.21%, 3.45%, and 5.32%, respectively, under the optimal extraction condition of P204-P507 concentration of 15% (v/v), P204 to P507 ratio of 3:1 (v/v), TBP (Tributyl phosphate) concentration of 5%, sulfonated kerosene concentration of 80%, initial pH of 1.8, contact time of 8 min, and phase ratio (O/A) of 2:1. By confirming the predictions of the McCabe-Thiele diagram, a five-stage countercurrent extraction was carried out and the desirable extraction efficiency for vanadium reached 98.13%. The maximum co-extraction coefficient and distribution ratio of vanadium were 2.58 and 26.23, respectively. The stripping efficiencies and concentrations of a vanadium-rich solution by three stages of countercurrent experiments with 20 vol.% sulfuric acid reached 99.14% and 0.58 g/L, respectively, while almost all of the titanium remained in the organic phase. The mechanism of synergistic extraction between hydrogen ions of P–O–H and VO2+ in acidic conditions was confirmed by ATR-FTIR spectroscopy and molecular structure derivation. Besides, the separated impurity ions ( Fe2+) after oxidation, precipitation, and roasting process form a qualified iron oxide pigment with a total iron content of 97.2%.

Apr 25, 2023

By J. W. Butwell

Anaconda has been active In the Bingham mining district near Tooele, Utah since 1914 when the company acquired International Smelting & Refining Co. Over the years both custom ores and complex Pb-Zn-Cu ores from the district were milled and smelted at International. In 1948 Anaconda acquired the property that covers the present Carr Fork ore body. Since that time active exploration took place in the 50's followed by detailed geological evaluation in the 60's. Convinced that high grade Cu deposits would be found at depth, a deep drilling program commenced in the late 60?s, with intersection of the ore zone in 1969. Following extensive deep drilling in the early 70?s, a feasibility study was conducted in 73-74 with board approval given Sept. 6, 1974. The 9,000 t/d mine-mill complex was budgeted at $217 MM over a 5 year schedule with start-up in Sept., 1979. The following discussion includes the concentrator and surface facility portion of the budget or approximately $60 MM of the scope. Special emphasis will be made on equipment selection and layout.

Jan 1, 1980

By J. J. Renton

The iron disulphide minerals, pyrite and to a lesser extent marcasite, are ubiquitous to coal and coal associated rocks and are the source of nearly all the environmental problems associated with the mining, processing and utilization of coal. The iron disulphides as well as the other minerals in coal exhibit systematic spatial pat- terns of distribution on both regional and local scales and show predictable associations, most of which are determined by the geochemical-sedimentological controls under which they form. It is the purpose of this paper to discuss the geochemical-sedimentological conditions responsible for the formation of coal minerals with special emphasis on the formation of iron disulphides, to illustrate the regional and local patterns of mineral occurrence within coal, to present the microscopic associations of the iron disulphides and finally, to discuss the most important single environmental aspect of the iron disulphide content of coal and coal associated rocks; the production of acid mine drainage.

Jan 1, 1986