Search Documents

By Gary L. Simmons

Noranda's Grey Eagle Mine and Mill, located in the Siskiyou Mountains of Northern California, began shakedown operations in the late fall and early winter of 1982. This paper describes some of the unique features in mining, milling and water treatment operation at Grey Eagle. In addition, major start-up problems in the mill and water treatment plant are discussed along with measures taken to correct these problems.

Jan 1, 1984

By R. D. Smith

The Bureau of Mines (BOM) evaluated the technology, capital investment, and annual operating costs of emission control for further reductions of lead in ambient air at the East Helena, Montana, smelter, and the Glover, Herculaneum, and Buick smelter-refineries in Missouri. This study seeks to analyze the technology available to the domestic primary lead industry for attempting to further reduce lead emissions below 1985 levels. Through enclosure of concentrate unloading and handling areas and all lead-processing buildings, followed by venting these enclosures to the atmosphere through baghouses and the application of appropriate local controls, emissions can theoretically be reduced by a total of 2,424 pounds of lead per day from 1985 levels at the three Missouri operations. Using conventional technology, aggregated additional capital costs of $250,014,000 and annual operating costs of $18,507,800 are estimated for the four operations, resulting in a total cost of $0.063 per pound of refined lead. Continuous drossing techniques would assist in meeting OSHA standards in process areas. Continuous drossing would change capital and operating costs to $258,344,800 and $16,104,700, respectively, for a total cost of $0.062 per pound of refined lead. First quarter, 1986 open market price for refined lead was $0.184 per pound.

Jan 1, 1986

By C. St. J. Lowe

Weir Minerals ? Linatex has developed a new approach to the dewatering of fine solids, particularly mine and process plant tailings and wastes. The Weir process, patented in 2009, uses standard process equipment in a standard flow sheet, but applies this approach to materials previously thought to be too fine to be dewatered with this type of equipment. The process can be applied to a wide range of materials, making lower moisture products that can be re-used elsewhere or sent to disposal. It has already been tested successfully on a small scale in Australia on coal fines, zinc mine tailings, red mud, iron ore tails, and copper/gold tailings. The principal factors affecting the solids recovery have been established as: 1. The % solids in the slurry feed to the process ? a higher % solids provides a higher recovery. 2. The particle size of the feed solids ? coarser feeds provide higher recoveries. The key factors affecting the % solids in the dewatered product have been determined to be: 1. The particle size of the dewatered product - coarser materials produce a higher % solids in the dewatered product. 2. The height of the discharge weir on the dewatering screen - a higher discharge weir on the dewatering screen also yields a higher % solids. 3. The angle of the dewatering screen. Setting the screen horizontal increases the travel rate, reduces the bed depth and reduces the % solids in the dewatered product. Back-sloping the screen up to 5° reduces the travel rate and increases the % solids in product. Eight plants ranging in size from 3 t/h to 40 t/h have been sold to a range of customers in China, for coal and iron ore tailings treatment. Australia has one plant, a small unit rated at 30 t/h of sand fines, and has recently completed test work on iron ore tailings for a dewatering plant rated at 135 t/h. Additional tests are under way with clients around Australia, to demonstrate the capabilities of this process on specific applications and to provide confirmation that materials can be processed successfully, before moving on to larger scale tests or full size plants. The advantages of the Weir process include - lower moisture in products, uses proven equipment, lower capital and operating costs, lower maintenance costs, reduced power consumption, compact footprint, can be used in parallel or in series with existing equipment, modular design to facilitate redundancy or expansion, efficient water recovery and simpler water management, reduced cement in backfill mixes, smaller tailings disposal footprint, reduced earthworks requirements, much lower seepage losses, more stable tailings mass, progressive site rehabilitation, reduced impact on local wildlife, reduced risk of dam wall failure, and reduced environmental monitoring and compliance costs.

Feb 23, 2014

By H. M. Brennecke

A new hydrometallurgical process has been developed to recover copper from sulfide ores. Copper is leached in a staged reactor system utilizing nitric and sulfuric acids at 105°C. Iron is removed from the pregnant liquor as a jarosite and cathode copper is electrowon directly from the purified pregnant liquor. The spent electrolyte is recycled. Nitrogen oxides evolved from the leach are reconverted to nitric acid and are also recycled. Sulfur is rejected as S°, jarosite and gypsum. The process is highly versatile and can recover precious metals, molybdenum and zinc, when these elements are present. Continuous, integrated, semi-pilot plant operations using chalcopyrite ores demonstrated 99% copper leaching and production of cathode grade copper. Economic evaluation shows that the process is competitive with pyrometallurgical and other hydrometallurgical processes.

Jan 1, 1978

By M. F. Werneke

Flotation of the carbonate, oxide and silicate minerals of copper (malachite, azurite, chrysocolla) has been the subject of much research in recent years, but few effective solutions to this problem have been found. With decreasing reserves of sulfide minerals, the economic recovery of these "oxides" appears to be an important source of copper for the future. Xanthates have been known for many years to be malachite collectors (1), but only at very high dosages, or at lower dosages following activation of the mineral by sulfide ion. Dewitt and Batchelder (2, 3) found that chelating agents such as certain oximes were collectors for malachite and azurite, but also required high reagent dosages. Fuerstenau (4) has suggested, for example, that potassium octylhydroxamate may be an effective collector for malachite, On the other hand, Balberyszski (5) has found that oxide minerals may be completely sulfidized at high temperatures with gaseous sulfur or H2S, and then floated with conventional collectors. None of the above approaches appear to offer an economically effective method for the direct flotation of these oxide minerals.

Jan 1, 1977

By D. Scott Scovira, Thomas Gustavsson

Exiting WW2, the potential of nitrates and hydrogen peroxide for application as industrial explosives both became known. The technology stream advanced the development and uptake of nitrate-based explosives to the point that they are the current global standard for blasting. Recently environmental issues are influencing the strategic agenda of extractive industries. The mid-2010s saw renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the 2020s provided additional impetus to investigate hydrogen peroxide-based explosives. Hypex Bio is at the forefront of developing and delivering bulk gas sensitized Hydrogen Peroxide Emulsion (HPE) for blasting. HPE consists of hydrogen peroxide along with smaller amounts of fuel and emulsifier. The consistency of HPE is similar to industry- standard nitrate-based emulsions. It is compatible with existing priming and initiation systems. HPE does not contain nitrates and thereby does not produce post blast nitrous oxide fumes nor discharge of nitrates or ammonia to mine water. Importantly, HPE contributes to reduction in total carbon emissions as compared to nitrate-based explosives.

Feb 1, 2025

By Minerals and Materials Analysis Section

During 1996, US mines produced 319 t (10.26 million or) of gold metal valued at $4 billion. At yearend, mine reserves were estimated to be 4.7 kt (151 million oz) of gold metal. Almost all of the production was from western states. Nevada accounted for about 68% of national production. Information for this article was obtained through annual reports of mining companies, US Geological Survey (USGS) databases and other public sources. Table 1 shows production and reserves by mine. It divides the mines into two categories. These are producing mines whose primary product is gold, and producing mines for which gold is a byproduct or coproduct. The mines listed in Table 1 accounted for more than 98% of US gold production during 1996. Except the Daisy Mine, the table does not include mines that produced less than 31 kg/a (1,000 oz/year). The Daisy Mine started production in December of 1996. Nor does it contain mines whose byproduct concentrate is

Jan 1, 1997

By Albert W. Deurbrouck

The coal reserves in the United States are estimated to be in excess of 300 billion recoverable tons, and current projections of energy requirements indicate our increased dependence upon these reserves. The Department of Energy's Energy Outlook for 1984 projects that coal consumption in the United States will increase from 737 million tons in 1983 to 958 million tons in 1990, and then to 1,110 million tons in 1995 (Table 1). As shown in this table, the future utilization of coal in the United States is closely tied to the electric utility market, a market that consumes about 85% of the coal produced. Be- cause of this dependence on the utility market, the uncertainties of new environmental regulations, particularly those concerning sulfur emissions, could have a significant adverse impact on future coal demands in the United States. SULFUR IN U.S. COALS Most of the Nation's coal reserves contain too much sulfur to be fired directly and meet existing emission control standards. In Table 2, the sulfur contents of the coals of the eastern United States are summarized by sulfur levels according to regions. While the coals of some of the eastern regions are predominantly high in sulfur content, it is important to recognize that large tonnages of coal with relatively lower sulfur content are available in these regions. Furthermore, an often significant portion of the sulfur occurs in the form of iron sulfide (Fes2 or pyrite). Because pyrite occurs as discrete particles of high specific gravity, it can often be removed by simple, inexpensive physical coal beneficiation techniques after being liberated by stage crushing. The potential for physical removal of pyrite by conventional specific gravity processes combined with stage crushing is summarized in Table 3 on a regional basis.

Jan 1, 1986

By J. Y. Lee, J. Kang

"A selective chlorination process using cuprous chloride (CuCl) was investigated for producing high-grade chalcocite (Cu2S) from chalcopyrite (CuFeS2) feed. The chalcopyrite feed was reacted with CuCl in the presence or absence of sulfur (S) at temperatures between 900 and 1,100 K for five hours under an argon gas atmosphere. The experimental results indicate that iron (Fe) was selectively removed from the chalcopyrite feed as ferrous chloride (FeCl2) at 1,100K and the mass percentage of Fe thus decreased from 31.5 percent in the feed to less than 0.05 percent in the residue, under certain conditions. As a result, high-grade Cu2S was obtained from chalcopyrite in a single step. This new selective chlorination of chalcopyrite using CuCl as a chlorinating agent is therefore feasible for producing high-grade Cu2S.IntroductionCurrently, blister copper (Cu) is commercially produced from sulfide ores by pyrometallurgical methods. These methods entail matte smelting and converting, with the removal of iron (Fe) and sulfur (S) as slag — mainly Fe2SiO4 — and sulfur dioxide (SO2) gas, respectively.In the pyrometallurgical method, as shown in Fig. 1 (Schlesinger et al., 2011), Fe is removed through two steps at high temperatures of around 1,500 K to reduce the loss of Cu during slag formation. However, the slag still contains 1 to 8 percent Cu. Therefore, Cu in the slag is recovered by slag treatment processes, after which the concentration of Cu in the slag decreases to around 0.4 to 1.3 percent. Although Cu is recovered, the slag that had undergone the treatment processes is difficult to use as a feedstock for ironmaking owing to the small amount of Cu remaining in the slag (Schlesinger et al., 2011).In addition, large amounts of SO2 gas are generated by the oxidation of S in the current Cu production process. The SO2 gas generated is captured and used to produce sulfuric acid (H2SO4). However, despite the development of SO2 gas-capture technologies, the emission of SO2 gas is still a problem in terms of environmental considerations.Several studies had been carried out in the past to overcome the drawbacks of the current process. The extraction of Cu from sulfide ores using a chlorination process is one alternative that had been investigated by several researchers. Most chlorination processes used chlorine gas (Cl2) as a chlorinating agent at temperatures between 573 and 1,023 K under an inert atmosphere (Donaldson and Kershner, 1962; Olsen et al., 1973; Kumar, Li and Warren, 1985, 1987; Kanari et al., 1999; Kanari, Gaballah and Allain, 2001)."

Jan 1, 2017

By J. Evans

INTRODUCTION Section 209(b) of the Federal Land Policy And Management Act of 1976 (FLPMA-43 U.S.C. 1719 b) authorizes the Secretary of the Interior to convey mineral interests owned by the United States where the surface is or will be in non-Federal ownership. The objective is to allow consolidation of surface and subsurface (mineral) ownership. Certain major conditions must prevail for a conveyance to occur. These are: 1) There are no known mineral values (KMV) or 2) Where the mineral reservation interferes with or precludes appropriate non-mineral surface development and that non-mineral development is a more beneficial use of the land than the mineral development. Remember that allegation, hypothesis or speculation that the conditions could or may exist in the future will not be a sufficient basis for conveyance. Convincing factual evidence for an applicant’s case for mineral conveyance must be made in order to achieve that conveyance. See 43 CFR 2720 0-1 to 0-3, and 0-6. CONCEPT OF KNOWN MINERAL VALUES Known mineral values means mineral rights in lands containing geologic formations that are valuable in the monetary sense for exploring, developing, or producing natural mineral deposits. The presence of such mineral deposits with potential for mineral development may be known because of previous exploration, or may be inferred based on geologic information (43-CFR 2720.0-5(b).

Jan 1, 2007

By V. A. Mironenko

The combined study of ground water regime and rock deformations has resulted in the theoretical substantiation of the common principles for analysis of the hydrodynamic and geomechanical processes Within the scope of unique scientific direction -hydrogeomechanics (Mironenko and Shestakov, 1974). The hydrogeomechanical models are widely used now for the analysis and forecasting the extremely important processes connected with the safe and efficient mining operations, as well as with the protection of geological medium. Among these processes are: -deformations of the open-pit slopes and spoil dumps; -consolidation of rocks due to the ground-water pressure drop; -water-end-rock material inrush into mine workings caused by deformations of the undermined rock mass; -geodynamical processes due to the changes in ground water regime; -artificial hydrofracturing in rocks; -transformations of clay linings under the tailing ponds and other technical water basins.

Jan 1, 1990

By R. S. Jurani

Sunshine Mining Company's Kellogg operation is the primary silver producer in the United States, and maintaining a comfortable working environment in this deep underground mine historically has been a complex and costly problem. To improve the ventilation and cooling systems at a time of declining and uncertain silver market, it was proposed to optimize the performance of existing facilities at minimum cost. This paper discusses a 2-year, $400 000 optimization program that resulted in increased total mine airflow, cooler ambient temperatures, reduced compressed air usage, and lower energy consumption by primary fans, air compressors, and refrigeration plants, thereby saving the company approximately $650 000 per year.

Jan 1, 1987

By Brent A. Elliott, J. Richard Kyle

Texas is a major producer of industrial mineral resources required by the state’s ever-growing population that now exceeds 28 million. Texas typically ranks in the top three states for the value of non-fuel mineral production with a total value of $5.2 billion in 2017, accounting for 6.9% of the total US mineral value. Almost 90% of current Texas industrial mineral value comes from the production of cement, crushed stone, industrial sand, and construction sand and gravel. Construction material consumption is focused in the 25 metropolitan areas of the state with populations of > 100,000 residents. Industrial mineral consumption is dominated by the four most populous regions of the state—Houston, Dallas-Fort Worth, San Antonio-New Braunfels, and Austin-Round Rock—with an aggregate population of more than 18 million. More than 11,000 employees work in Texas mining and processing operations. Texas produces more crushed stone than any other state from more than 200 quarries; a similar number of operations produce sand and gravel. Specialty industrial sand production for use as proppants in hydraulic fracturing for enhanced petroleum production serves as an excellent example of how developments in one industry sector can markedly affect another industry; the production of industrial sand in Texas has markedly increased over the past decade, reaching $1.3 billion in 2014. With Texas’ population projected to reach 50 million by 2050, continuing in-state development and production of industrial minerals will be required to supply its residential, commercial, and industrial users. Favorable geology and economic factors provide opportunities for identification and development of new industrial mineral production sites.

By George E. Edwards

Pacific Rim markets for export coal already represent a larger market than the total tonnage imported into the European Community countries and they will continue to expand. The largest importers will continue to be in the sector comprising Japan, Korea, Hong Kong and Tai- wan. It is likely that the total Pacific Rim markets will reach 206 m.t.p.a. by 1990 and 290 m.t.p.a. by 2000, with the major growth in steam coal demand. Australia has an efficient coal industry, represents a stable long term source of supply and is favourably situated geographically to continue to be the largest single supply source.

Jan 1, 1982

By William A. Gibson, Kenneth P. Neumann

In 1967, development of the Cyprus Thompson Creek molybdenum deposit began near Challis, ID. The first mining claims were staked on an intrusive rock out-crop. Exploration continued for 14 years. In 1978, the decision was made to develop the deposit. In Dec. 1980, approval was received for the environmental impact statement and facilities construction and waste rock removal began. By the middle of 1983, 126 Mt (139 million st) of rock had been removed and all facilities completed. Location The Thompson Creek project is located about 58 km (36 miles) southwest of Challis in Custer County, in south central Idaho. The mine and mill are situated between 2.2 and 2.6 km (7,217 and 8,530 ft) in elevation. The project is located in an isolated area. Surrounded by mountains, it is adjacent to the Sawtooth National Recreation Area. The Salmon river is 8 km (5 miles) south of the project. The project claim block is lo-

Jan 1, 1984

By William F. Riggs

Inspiration Consolidated Copper Company, located in a semi-arid climate in Arizona, continually struggles with a water problem. This applies to quality as well as quantity. When the EPA considered installing a new centralized sewage plant to handle the combined waste from the municipalities of Globe and Miami, Arizona, they automatically assumed that He could use the sewage effluent for process water in flotation. The treatment plant was to be a tertiary system producing 1600 gpm of sewage effluent. Inspiration decided that this could possibly be a source of additional process water. It was decided to test sewage effluent from Miami Treatment Plant at the rate of 400 gpm since it was only a primary treatment plant. The 400 gpm was combined with the 5000 gpm of process water going to the Concentrator. After one week the results were disastrous. The recovery and final grade had each dropped approximately 5%. With the results from this brief run, it was concluded that sewage effluent from a primary treatment plant could not be used. Research was then brought into the problem to begin an evaluation of sewage effluent in flotation.

Jan 1, 1977

By Duah Philip, Awuah-Offei Kwame

Regulatory pressure to mitigate the cement industry’s environmental impact has intensified recently, spurring innovation in low-carbon cement technologies. In the United States, cement production, consumption, and carbon emissions are accelerating. Despite this trend, the adoption of environmentally friendly dry clinker production technology with combined preheater-precalciner systems has surged from 53.3% in 2002 to 88.5% in 2019. Concurrently, reliance on wet technologies, known for their higher environmental impact, has dropped from 16.5% to 0.6% within the same period. This paper presents the results of our comprehensive study, utilizing over 100 years of industry data, to analyze these technological shifts and their environmental implications.

Feb 1, 2025

A comprehensive understanding of the effects of autoclave configuration (batch, semi-batch, continuous) on the residence time necessary to achieve a target conversion is a prerequisite for design of commercial scale autoclaves. Particle size distribution, mineral and reagent concentrations, temperature and mixing also influence the conversion. This paper outlines the bases of using test data to predict performance of commercial scale autoclaves. Recommendations for coordinating test program design with selection of scale-up method are provided. Examples are given to illustrate the different levels of engineering effort needed to meet corresponding levels of design optimization and accuracy.

Jan 1, 1998

By Stephanie Singarayer, Damodara Reddy Chinnasane, Mike Yao, Danielle Pelletier

Mining at Vale’s Creighton Mine has been active for nearly 120 years in Sudbury, Ontario, Canada. Being the deepest mine in the Sudbury region, mining induced seismicity is a common occurrence at Creighton Mine. Over the past five years, 26 large magnitude seismic events ranging from 2.5 Mn to 3.7 Mn (Nuttli) have occurred. Out of these large magnitude events, three 3.0+ Mn events occurred between April 2020 and January 2021. The majority of the 3.0+ Mn events are believed to be the fault-slip type that could be linked to the known major geological structures and/or long-term effect of mining over many years. The recent large magnitude events are believed to be triggered by high induced stresses while mining the first few stopes of a new lower horizon in the top-down centre out mining sequence.

Apr 26, 2022

By Gregory Rumbaugh, Christopher Mark

Recent pillar collapses have caused five large airblasts in underground U.S. limestone mines. One of these events injured three miners, but all of them put many other miners at risk. To better understand the hazards, Mine Safety and Health Administration (MSHA) conducted a comprehensive review of the international literature on airblasts. More than 40 airblast cases have been documented, in a wide variety of minerals. Experience shows that miners that are in the direct path of the air as it moves towards the mine exits are at the greatest risk. The paper describes a risk management methodology that can be used to evaluate the level of hazard throughout the mine and aid in the selection of controls to reduce the risk. The paper concludes with a detailed case history of an actual pillar collapse and airblast.