Search Documents

By D. Men, R. Q. Honaker, J. C. Hower

"Maceral separation is one possible technique to expand coking coal resources, either by increasing the blending ratio of non- or slightly caking coal or rationally utilizing the coking coal according to the different behaviors of macerals in coking. The success of maceral enrichment for a given coal using flotation is dependent on the differences in flotation kinetic rate among macerals. This paper presents the flotation rates and zeta potentials of the vitrinite-rich and inertiniterich maceral concentrates obtained from six coal samples of different ranks – from high-volatile B bituminous coal with mean random vitrinite reflectance (Rrandom) of 0.64 percent to low-volatile bituminous coal with Rrandom of 1.73 percent – using a float-sink procedure. The flotation results show that vitrinite-rich concentrates can be produced in tap water using froth flotation only with frother for the high-volatile B and A bituminous coal samples, but there was no good performance for the high-volatile C bituminous and medium- to low-volatile bituminous coal samples. The zeta potential results show that froth flotation could probably separate the high-volatile C bituminous coal samples well by adjusting pH, but there was no good performance for the higher-rank coal samples. IntroductionMetallurgical coke is used in blast furnaces for steel production and is produced by the carbonization of coking coal. Because caking coals are rare and expensive, they are often blended with non- or slightly caking coals. Considering the tight supply-demand situation for coking coal in China, it is important and urgent to develop highly efficient technologies for rationally utilizing and expanding coking coal resources (Mochizuki et al., 2013)."

Jan 1, 2015

By R. Zins

During the past few years, a completely new concept has been applied to the design of drives for operating at very low speeds. In this, the motor is supplied by a variable-frequency thyristor cyclo-converter. Today, frequency converters with practically unlimited power ratings can be constructed. The system frequency of 50 or 60 Hz is reduced to about 10 % of these values. This makes it possible to operate the synchronous motor, which has a correspondingly high number of poles, at the extremely low speed of the driven mill, i.e, without interposed gearing. The first motors of this type were built to drive ball mills in the cement industry, which are very similar to those employed for ore processing. Here, too, the tendency is to build units of ever increasing capacity. In the case of conventional drives with mechanical gearing, this involves correspondingly increasing difficulties. These difficulties have prompted various studies of the possibility of applying the new type of drive to ore mills as well, but a gearless drive has not yet been built for this application. However, gearless drives for ore mills will certainly materialize soon and it was therefore considered a logical step to report at the A.I.M.E. Conference on the experience gained with these drives in the cement industry, and on the present state of development.

Jan 1, 1973

By R. E. Hamilton

It is more than ten years since the first fully automated process using a computer started operation. Computer control has become common in a number of process industries, yet in spite of the tremendous incentives which ere present, there are only a few computer installations in the mining industry and none of these has announced successful control of a process. Recognizing that one of the reasons for this slow progress is the lack of adequate mathematical models of the various processes involved, the author's company started a project in the summer of 1966 to develop such models. It was early recognized that the existence of a major disturbance input, in the form of the mineral composition of the feed prevents most flotation plants from attaining a steady state condition. This makes the custom¬ary method of developing correlations from steady state plant data inapplicable and requires a more fundamental approach.

Jan 1, 1968

By Dirk van Zvl

The design of cover systems for reclamation schemes in tailings requires estimation or determination of tailings materials properties such as compressibility, shear strength and consolidation characteristics. It is very difficult and expensive to obtain truly undisturbed tailings samples for laboratory testing. In situ testing methods have been developed for economically obtaining large amounts of information. Two of these methods are described, the piezocone and the flat plate dilatometer. Both of these methods provide a rapid means of detailed material identification in a nearly continuous fashion for the entire depth investigated. The equipment is described and typical data from a uranium tailings impoundment is presented. The results are compared and the advantages and disadvantages of these methods are discussed.

Jan 1, 1984

By David Cronan

"Most of the recent renewed interest in manganese nodule mining has been focused in the Clarion-Clipperton Zone (CCZ) in the NE tropical Pacific where nodules are rich in Mn, Ni and Cu. However, equally interesting, but compositionally different, nodules occur in the tropical central South Pacific (CSP). The CC Zone deposits lie in the International Seabed Area whereas those in the South Pacific lie mainly in the Exclusive Economic Zones of Island States, principally the Cook Islands and Kiribati. The CSP nodules should not be regarded as an alternative resource to CCZ nodules, as they are enriched in different elements. Rather, the CCZ nodules should be thought of as a source of one group of metals (Mn, Ni and Cu) and the CSP nodules the source of another group (see below), mutually complementing each other and to be mined in parallel for their different metals.Manganese nodule mining in the South Pacific has been mooted since the 1970s. However, new data on manganese nodule composition and abundance there have recently appeared. Also, a recently developed interest in 'rare', 'green' and 'technology' elements has necessitated a re-examination of old South Pacific nodule data for information on these elements (previously thought to be economically unimportant), and the re-analysis of the deposits to obtain new data on them. Additionally, current and possibly future applications to the UN to extend island 'continental shelf' areas necessitates an appraisal of the manganese nodules in these areas. These developments have prompted recent work that has helped to refine our understanding of the distribution and abundance of metals of traditional interest in South Pacific nodules, namely Mn, Co, Ni and Cu, but has also drawn attention to other elements of possible economic interest including titanium (Ti), vanadium (V) and the rare earth elements (REE)."

Sep 1, 2014

By Elisa Comis, Jeffrey Peterson, Yama Ebrahimi

Construction of the Northeast Boundary Tunnel (NEBT), the last leg of the Anacostia River Tunnel System on DC Water’s Clean Rivers Project, started in September 2018 and was completed in April 2021. The 26-foot-bore earth pressure balance (EPB) tunnel boring machine (TBM) mined 26,737 feet at elevations between 80 to 160 feet belowground. Approximately 55% of the tunnel was cut through lower predominantly coarse-grained facies identified as the Cretaceous Patuxent Formation (undifferentiated) (PTX), and the remainder was cut through upper predominantly overconsolidated fine-grained plastic material facies identified as the Cretaceous Patapsco/Arundel Formation (P/A). Mixed face conditions were encountered in the transition from the P/A to the PTX and vice versa. This paper reviews the performance of the TBM that mined the NEBT through several unique challenges, including 8,000 feet of tunneling under the heavily developed Rhode Island Avenue corridor, major sensitive structures, cast iron water distribution mains, and other sensitive utilities.

Dec 1, 2022

By C. R. DeGennaro, M. R. Girman, J. Bickson, J. P. Homer, C. C. Jobes

Between 2005 and 2021, a NIOSH internal review showed that haul trucks were involved in 54 incidents at surface mines in the United States. Haul truck collision warning and avoidance systems (CXS) can assist in preventing accidents at surface mines. CXS use technologies to detect people or objects and alarm to alert haul truck operators. Robust testing can help ensure that they detect objects without excessive false positive alarms. Testing and validation would increase confidence in and encourage implementation of a CXS. Researchers from the National Institute for Occupational Safety and Health (NIOSH) reviewed documents related to the evaluation and validation of CXS with two objectives: (1) to identify methods and parameters used to evaluate detection performance and (2) to identify gaps in CXS test methods and in detection performance. Stakeholders can use the findings from this research to guide implementation of CXS to improve safety at surface mines.

Mar 2, 2022

Nearly as impressive as the machines that will be on display at MINExpo are the massive engines and tires that keep the machines moving. As you can imagine, it takes a special tire and special engine to run these machines. The following is a look at some of the exhibitors that will be at MINExpo displaying engines and tires. Cummins Inc. Cummins Inc. will display a lineup engines from 37kW to 2,983 kW (49 hp to 4000 hp) at MINExpo, representing the most extensive ?smallest to largest? range the company has ever put on display.

Jan 1, 2012

By Wayne W. Murdy

Peru is a mineral hot spot in the world today. Newmont is in the exploratory phase of this mining cycle, a phase full of optimism and expectations. But exploration is high risk. There will be successes but also failures. Many foreign companies will come and go. But it is the responsibility of the mining industry leadership of Peru and the government to continue to foster an environment conducive to investment. This is the time of year companies begin planning their next annual report. Last year, Newmont’s was called “new horizons.” It highlighted the company’s global expansion into Peru, Uzbekistan and Indonesia. Now, projects that were only on the horizon a year ago are moving into production. So “turning opportunity into gold” may be this year’s theme.

Jan 1, 1996

By Gy. Deák Deák

The ECOMINING platform aims to develop a scientific and technical organization in order to promote within the natural resources industry a framework for environment-friendly exploitation technologies (on Best Available Technologies principle) and also to develop a solid basis for performing Research and Development projects. The ground of this project is the success of the First International Seminar: ECOMIN-ING - Europe in 21st Century1, organized by the Research and Development National Institute for Metals and Radioactive Resources Bucharest in co-operation with ITASCA Consultants GmbH Germany, the University of Petrosani and supported by the National Society of Salt Bucharest & Praid salt mine branch and the Ministry of Economy and Commerce. The platform provides a complex data base, for partners? selection and researchers? team structure. This can provide the scientific results with a high level of confidence for the projects of interest in the field of exploitation of mineral resources and for the participation on national and international project proposals competitions (i.e., target the 7th Framework Programme or any European / national programme, which can provide funds for the ECOMINING platform field of interest). The next step is the affiliation of the ECOMINING platform to the European ones, and to be compatible with them. The ECOMINING platform represents itself a 7th Framework Programme (FP) project idea.

Jan 1, 2007

By F. P. Jung

This presentation will be a general overview of the Cerrejon Coal Project being developed jointly by Carbocol, an entity of the Colombian government, and Intercor, an Exxon affiliate. The word "Cerrajon", by the way, is simply Spanish for a small hill. There is a distinctive hill near the mine site, and it's the only landmark of any significance. It's shown in Figure 1. So the locals call this area "El Cerrejon", "the little hill." Let me start with some of the highlights of the project, summarized in Figure 2, and then go into more detail later. A four-year feasibility study covered the geology, quality, engineering, construction operation and marketing of coal from this region. This study led Exxon to declare the project as commercial in July of 1980. Then in September of 1980 the president of Colombia gave the government's okay to proceed.

Jan 1, 1982

By V. R. Degner

The trend in both the metallic and non-metallic mining industry is toward processing increasing y higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This paper reviews the R&D approach used in translating smaller flotation machine experience to establish the configuration of a 1000 cu ft (2B.3 cu m) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1978

By H. J. van Antwerpen

AngloGold Ashanti operates the world`s deepest mine, Mponeng gold mine, in South Africa. A vast refrigeration and ventilation system provides acceptable working conditions 3800m below surface at 60°C rock temperature. In such a system, optimisation and assessment of modifications becomes very difficult. With that in mind, a research project was launched to determine whether recently developed system simulation technology can be applied to a mine as vast and complex as Mponeng. Using the techniques and methods as implemented in FLOWNEX software, it was indeed proven to be possible to do a mine-wide combined simulation of compressed air flow, ventilation air psychrometry and refrigeration water systems. Interactions between the various streams included heat transfer, pressure drop, evaporation and condensation. The simulation model was used in a parametric study to test various water flow and temperature operating points for the refrigeration system. It was found that, given current limitations, the mine refrigeration system is running fairly close to optimal but with some opportunities for improvement. The simulation model also provided useful insight for future changes or extensions to the system.

Feb 23, 2014

By Mathew Cook

Technological developments in Distributed Fiber Optic Sensing and improvements in both hardware and software have allowed fiber optic sensing systems to be deployed in a variety of applications such as pipeline leak detection, perimeter security monitoring, and power cable real time thermal rating. Recently, there has been a larger adoption of monitoring of conveyor belts in so called Conveyor Health Monitiring Systems (CHMS) within the mining and bulk material handling industries to identify idler conditions on an ongoing basis. Several attempts have been made to institute sensing capabilities into conveyors with mixed success. However, recent breakthroughs in modeling, installation methodology, and technology, as well as increased understanding of application and industry requirements, have allowed the technology to be deployed at both experimental and commercial scales. This paper summarizes the application conditions and requirements, design considerations, methodologies used, the outcomes achieved, the logistical and field considerations, and the future possibilities of the use of this technology in CHMS using Distributed Fiber Optic Sensing.

Feb 22, 2026

By F. D. Fox

Abandoned mill tailings deposits can be found scattered throughout the Northern Black Hills of South Dakota, indicative of past mining activities that originated during the great gold [ERRATA SHEET RESTORATION OF GOLD MILL TAILINGS, BLACK HILL, SOUTH DAKOTA 84-119 F. D. Fox Under subtitle Prospects Related to Present and Future Tailings Disposal Practices, include reference No. 12 in paragraph seven after "construction of the Grizzly Gulch tailings disposal project,"12 Reference 12 should read: Jeffries, Lawrence F. and Tczap, Andrew, "Homestake's Grizzly Gulch Tailings Disposal Project," paper presented at 1978 International Mining Show, October 11, 1978.]

Jan 1, 1984

By Shakuntala Tudu, Indrajit Paul, Surajit Sinha, Pulibandla Basaveswara Rao, Shaik Mahaboob Basha, Srinivas Dwarapudi

The iron and steel manufacturing sector directly accounts for 7–9% of global CO2 emissions. Raw material preparation, such as iron ore sintering, pelletizing, and cock making, is the major CO2 emitter. As climate change becomes a bigger concern, steel manufacturers need to lower CO2 emissions without hindering efficiency or increasing costs. In recent years, the percentage of iron ore pellets in blast furnaces has increased due to its uniform size, good reducibility, and high tumbler index. Pelletizing is energy-intensive and emits considerable CO2. Around 20% of CO2 emissions during pellet making come from fluxes. In the present work, the authors established a novel CO2- free flux called wollastonite (CaO.SiO2) for sustainable palletization. Pellets with varying percentages of wollastonite (0–6%) are prepared and tested for chemical, physical, and metallurgical properties. Image analysis through an optical microscope is carried out to quantify the phases of fired pellets. SEM–EDS is performed to evaluate the chemical composition of the melt and slag phases. The results showed that the reducibility index (RI) and swelling index (SI) of pellets decreased with an increase in wollastonite dosage. Pellet strength increases with an increase in wollastonite addition up to 1.2% CaO (2.27% wollastonite), and a decrease in strength is observed thereafter. The increase in strength is attributed to the increase in slag bonds. The decrease in strength beyond 1.2% CaO is mainly because of an increase in low melting eutectics and more magnetite content. Pellets with 2.27% wollastonite to get 1.2% CaO showed good physical and metallurgical properties.

Mar 4, 2024

By Pratt Rogers, Aaron Young

Digital transformation (DT) is the process by which entities adapt themselves to modern technology. As digital technology becomes more prevalent (automation, cameras, sensors, touchscreens, artificial intelligence, etc.), there will be increased pressure on companies to leverage it for additional gains. For many companies in the mining industry, this will involve overcoming a steep learning curve. Furthermore, as the long-term success of the mining industry is dependent on a labor force with new skills (data management, analytics, digital literacy, etc.), new curriculum will need to be appended to the mining engineering discipline. This paper considers the mining industry’s need for DT. Then, it presents a three-part review of the foundational components of the DT process–ubiquitous data, connectivity, and decision making. Finally, it provides a discussion on the future of DT in mining as well as a research direction, which identifies the need of academia to provide support for mining companies in the form of both research and the education of digitally literate, dynamically capable mining engineers into the coming decades.

By M. L. Harris

Coal dust produced during the mining process is a prime explosion hazard in underground coal mines. To inert the coal dust and prevent a catastrophic propagating dust explosion, rock dust is applied to the roof, ribs, and floor surfaces of mine entries. Currently, one determination of whether a mine is adequately protected from the coal dust explosion hazard is made by analyzing collected mine dust samples for percent total incombustible content (% TIC). A minimum of 80% TIC is required per 30 CFR 75.403. The as-received moisture of the dust sample is included in the % TIC. Moisture and humidity within a coal mine vary greatly with the seasons, with explosions occurring more frequently during dry winter months. This paper will discuss the fluctuations of the as-received moisture content of the mine dust samples collected by U.S. Mine Safety and Health Administration inspectors in 2010 and the observed fluctuations of the moisture content of rock dust within the U.S. National Institute for Occupational Safety and Health Office of Mining Safety and Health Research Bruceton Experimental Mine and the Safety Research Coal Mine over a one-year period.

By David L. Brostrom, William C. Brice, Perry A. Canton

The business of mineral exploration and development has become much more than simply a problem of locating orebodies and designing mines. Favorable economic analysis of mining and processing feasibility is no longer sufficient to justify the development of a mine. New laws, enacted by virtually every level of government, require comprehensive land use planning, environmental analysis, mineland reclamation, mine safety studies, and many other considerations. This profusion of new laws says in effect, that the mining company is no longer responsible only to its stockholders. Mineral development today can be compared to a partnership. As in all partnerships, the risks and liabilities as well as the benefits are held jointly by all the participants. In addition to the mining operator, this partnership consists of the public, through its many levels of government, interest groups, and individual citizens. Therefore, you'd better know your partner very well - his responsibilities and capabilities. Mining is considered a high risk venture. The risk on the part of the operator and the lending institutions has long been recognized. The risk that the public and its government take in these mining ventures has now been recognized also. The people and their government have learned that they inherit, through abandonment or forfeiture, the mistakes and problems of individuals and companies regarding these natural resources. In looking through the "Mining Engineering Handbook" recently published by the Society of Mining Engineers, I noted that in their discussion of liability for excavations, the authors quoted from the book of Exodus, 20th chap., where Moses said to his people: "When a man leaves a pit open, or when a man digs a pit and does not cover it, and an ox or an ass falls into it, the owner of the pit shall make it good; he shall give money to its owner, and the dead beast

Jan 1, 1974

The past four years since the 2008 MINExpo have been a roller coaster ride for the mining industry, with highs and lows and everything in between. One of the natural consequences of this uncertainty has been a number of significant consolidations and mergers, and this trend has trickled down into the crushing industry. And while there have been some significant changes to this sector of the mining industry, many of the big players have weathered the storm. The following is a look at some of the mineral processing companies that will be at MINExpo. McLanahan Corp. McLanahan Corp. is an example of the changes in the sector. The crushing and grinding stalwart acquired Universal Engineering, expanding its traditional focus on soft mineral crushing to hard rock crushing. At MINExpo, it will be showing off three new pieces of equipment, the LabMill Crusher, the Rocker Tooth Crusher and the Recessed Filter Press.

Jan 1, 2012