Search Documents

By Dennis Asmussen

The peatlands of the U.S. and Canadian parts of the Upper Great Lakes region have a long history of modest utilization in agriculture, forestry, horticulture, and as natural undisturbed areas. Only recently have they been assessed as potential sources of non-renewable or renewable energy. This new interest in peatlands, should current proposals be realized, might mean the commitment of millions of acres to energy production purposes. The magnitude alone of this potential utilization of peatland signals the possibility of substantial environmental disturbance, local resource shortages, resource use conflicts, and social and economic change. Peat- land resource managers in the region are just beginning to weigh the advantages and disadvantages of large-scale peatland utilization. The Minnesota Department of Natural Resources has made a considerable effort to study peat resource management issues and will shortly make recommendations to the state legislature regarding utilization alternatives. What follows is a general discussion of peatland utilization and management trends in the region with a focus on Minnesota and its peatland management efforts.

Jan 1, 1980

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

The understanding of the influence of the different types of apatite on the performance of mineral processing of igneous phosphate ores is still a challenge due to the difficulty to explain why some types of apatite floats in the froth flotation cell and others do not under the same conditions. Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão mine: predominantly blue apatite, followed by green apatite and less frequently yellow apatite. The chemical composition of these types of apatite was determined by electron microprobe analysis (EPMA) and LA-ICP-MS. Blue and green apatite respond well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite is the one bearing the lowest P2O5 content and the largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest P and Ca grades and lowest substitution level. A negative correlation of the amount of phosphorus with fluorine was observed. Furthermore, impregnation of iron oxide-hydroxides in the yellow apatite was also observed. Therefore, the low flotation behaviour is due to low crystallinity coupled with impregnation onto its surface.

Jan 31, 2022

By C. A. Rowland

The use of the Bond Work Index to size industrial grinding equipment is well known. Its use to measure grinding efficiency was presented by C.A. Rowland, Jr. at an AIME meeting in 1976. However, due to a bureaucratic error, the paper was never submitted for publication. This metric has nevertheless been adopted by industry as a widely used standard. The purpose of this paper is to re-present and update the application of this tool as a standard for measuring grinding circuit efficiency. Definition ?standard, n. something established for use as a rule or basis of comparison in measuring or judging capacity, content, extent, value, quality, etc.; as standards of weight and measure? (Webster, 1958).

Jan 1, 2008

By E. J. Garrison

A.C. Noble presents a clear and concise summary of the factors pertinent to a competent reserve evaluation of a mineral occurrence. However, I believe that he confuses the difference between a resource and a reserve. By definition, a reserve estimate includes all known economic, legal, mining, metallurgical and environmental factors impacting the recovery of the product(s) found in the deposit. A resource estimate, however, is an estimate of what is there - what is available for exploitation and should not include economic and other considerations. Only after defining the resource, its extent, location, physical and chemical properties, can an intelligent selection process begin of the extraction and processing technologies most appropriate to the circumstances encountered. The early and almost certainly inappropriate application of these often cookbook choices has probably lead many companies to walk away from good properties. (How many mines have been found in others rejects?) An example of the process is the early selection of metallurgical samples, after encouraging values are found in a few holes or surface samples, in an attempt to determine the economics of the prospect. Unfortunately, the sampler does not know how representative of the occurrence the sample is because he does not know what the deposit looks like. As a consequence, the property becomes saddled with a bad metallurgical sample that is often inappropriately used in evaluating the deposit which it does not represent.

Jan 1, 1994

By J. Best, K. Gallant

This paper explores the age-old concept of mine-mill reconciliation from a new perspective. Advances in reconciliation processes have been slow to materialize because in the quest for “rightness”, engineers, geologists and metallurgists have become entrenched in their viewpoints, dutifully performing to the metrics and expectations imposed upon them by the siloed organization. Moreover, reconciliation has not been viewed as a primary value creator, but an accounting non-value added task. In reality, the knowledge from reconciliation can significantly enhance yields. Critical review of the direct variables (tons, grade, etc.) and other less-obvious variables (incentives, communication, etc.) reveal a complex web of barriers to be cleared by management in order to realize benefits. Also, mineralogical reconciliation methods may offer renewed faith in the process.

Jan 1, 2004

By L. Shevenell, L. Stillings

The Acid Drainage Technology Initiative-Metal Mining Sector (ADTI-MMS) has established a Pit Lake Committee to enhance the science and understanding for the long-term management of pit lakes. Participation in this new committee is from members of federal and state agencies, industry, and academia, including numerous individuals representing 10 states. Work has begun on a pit lake literature search and review, database, classification, and sampling and monitoring procedures document. Coordination with the International Network for Acid Prevention (INAP) has been established. Future work will include preparing a prediction and assumption verification document, a report identifying variables upon which water quality is dependent, and an applied remediation technologies document, including an evaluation of the effects of backfilling.

Jan 1, 2002

By Erle I. Shobert

In the comparison and consideration of synthetic and natural materials, graphites represent a situation in which natural graphites amount to less than 10% of the total carbon and graphite production by weight, and less than 5% in dollar volume, There are few applications where it could not be re- placed by synthetic graphite. On the contrary, synthetic graphite materials can be engineered to cover an extremely wide range of applications. These include electrographite brushes for rotating machinery, pyrolytic graphite, graphite-impervious pipe, nuclear moderators, high purity spectrographic graphite, power tube anodes, graphite rotary shaft seals, and rocket nozzles. The special qualities of natural graphite and its limitations are delineated and the almost unlimited possibilities in artificial graphite materials are discussed.

Jan 1, 1964

By K. V. Raj, R. Jacksha

Conveyor systems persist in being a source of injuries and fatalities in the mining industry. To reduce these incidents, better methods are needed to enhance the monitoring of probable hazards and improve situational awareness during the normal operation and maintenance of conveyor systems. To address these issues, researchers from the National Institute for Occupational Safety and Health (NIOSH) continue to investigate emerging technologies that show the potential to improve miner safety around conveyors. This paper presents a feasibility assessment by NIOSH researchers of a fully integrated, commercially available wireless Internet of Things (IoT) system to improve situational awareness around conveyor systems. Included are discussions of a full-scale laboratory test bed that was designed to simulate a working conveyor system as well as the challenges and successes of integrating the IoT system with the test bed.

Oct 6, 2020

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining health and safety of miners. The authors evaluate potential real-time monitoring solutions for detecting and reducing diesel particulatematter, mine fires, and dust in situ, and examined the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limit. Authors review relevant documents, including research papers, trade publications, and manufacturers’ website-based information, to identify research gaps. The authors also evaluate contemporary sensors (airflow, gas, dust, silica), control system and software technologies, data transport systems, Industrial Internet of Things, ventilation network simulators, and control devices to identify potential health and safety research gaps. In this study, examples of some mines from Canada, Australia, and the USA are included where ventilation monitoring and controls have been applied. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

May 12, 2020

By Jordan Scheremeta, Sudhir Tripathi, Mahfooz Alam

Injection leaching can improve leach ore recovery by displacing retained solutions, enhancing ore wetting, and creating new flow paths for efficient solution collection. This paper presents a method to assess the feasibility of injection leaching in finer-grained, potentially contractive ores (from a geotechnical slope stability perspective) using limit-equilibrium (LE) slope stability analysis and static deformation modeling. LE models were carried out by assigning peak undrained strengths to the heap leach ore material, and modeling the excess pore pressure induced during the injection leaching process using spatial function in Slope/W. Static deformation modeling was completed using the software Fast Lagrangian Analysis of Continua (FLAC) to evaluate the potential for deformations due to the excess pore pressures induced during the injection leaching process. A constitutive model was used to represent the geomechanical behavior of the leached ore material, which enables the prediction of deformation and potential stability issues resulting from excess pore-pressure induced during injection leaching process. The two-pronged approach provides a practical method to assess geotechnical impacts and guide data-driven decisions in injection leaching operations.

Feb 22, 2026

By K. T. Brashear, N. Ripepi

"Over recent years, specifically following the MINER Act of 2006, an increasing number of manufacturers of underground mine seals in the United States have begun using a form of pumpable cement or shotcrete to create barriers separating the working and abandoned sections of underground coal mines. This seal material, while generally considered to be homogenous and solid, contains a network of microcracks, voids, and delaminations. Generally, it has been assumed that methane (CF4) leakage around these seals is a result of movement around the boundary interface between the seal and surrounding strata. Using a perfluorinated tracer compound, perfluoromethyl-cyclohexane (PMCH), the movement of gases can be monitored through seal material to observe how gases move though the material, both intact and with faulting in the material. This paper documents two large experiments where the movement of PMCH was monitored in the field, along with modeling confirmation using 3D visualization software. INTRODUCTION According to a report in 2007, there were over 14,000 active mine seals in underground U.S. coal mines alone (Zipf, Sapko, & Brune, 2007). These seals are used for both ventilation and safety purposes, to direct the flow of air away from the abandoned area of the mine and to help eliminate the propagation of explosions that can occur on the outby side of the mine seal. The atmosphere on the outby side of these seals typical consists of low levels of methane that have the potential of producing leakage along the face of the seal on the inby side. Methane leakage around mine seals has historically been attributed to the permeability between the seal and mine interface (McPherson, 1993). According to the United States Bureau of Labor Statistics (BLS) between 2003 and 2012 an average of 17 deaths occurred annually in underground bituminous coals mines. The only time during the ten-year period where the fatalities were higher than the average was in 2006 and 2010, years which had three major explosions occurring in underground coal mines in West Virginia and Kentucky. Two of the explosions were propagated through the mine by seal failure or methane leakage around newly poured seals (Light, et al., 2007) (Gates, et al., 2006). These recent events, and new regulations regarding seal strength (MINER Act), have created a need to monitor the condition of underground mine seals. BACKGROUND Measuring the permeability of solid materials, such as concrete or seal materials, can be a valuable tool in the field of non-destructible testing (NDT). By using an inert gas, such as nitrogen, injecting the gas into a solid structure, and measuring the resultant flow rate and pressure differential, this can provide valuable information about the structure. Studies have shown permeability can be affected by the stresses applied to the structure, as well as temperature and moisture (Choinska, Khelidj, Chatzigeorgious, & Pijaudier-Cabot, 2007) (Abbas, Carcasses, & Olliver, 1999)."

Jan 1, 2015

By Connor Langford, Murray Gant, Ken Massé

For public organizations, preparing accurate project cost estimates is a critical component in capital project planning. Project delivery methods provide a structured approach to moving projects through the design and construction lifecycle, and typically use cost estimates as key inputs at each stage to determine if the project will advance. As design stages can occur years or even decades before construction contracts are awarded, estimates need to make reasonable assumptions about how the work may be executed (means and methods) as well as potential future market trends so that appropriate values for material pricing, labour costs, escalation, and owner’s costs can be included. This process is challenging enough during stable markets, as historic trends can often be misleading and require a suitable understanding of economic factors to use appropriately. When you mix in the market volatility that has been observed since 2020, developing accurate project cost estimates becomes even more challenging. In cases such as this, having a structured approach to cost estimating that includes an adequate risk-based reserves cannot be overstated as it provides the basis for ongoing project decisions. This paper explores some of the historic and more recent market trends that have impacted key aspects of project cost estimates for capital project planning. It also provides recommendations on how to develop cost estimates for infrastructure projects, with examples from Metro Vancouver, which plans for and delivers regional-scale services to 2.6 million residents. A brief commentary on the use of escalation clauses in contracts is also presented.

Jun 13, 2023

By Atmesh K. Sinha

Death and injury rates in mining have been the highest of any industry; the injury severity rates in mines have also been the highest. Tentative figures reveal that 1971 was the best year yet for the bituminous coal indus¬try with the lowest number of fatal accidents. Nevertheless, 177 men were killed at a frequency rate of 0.76 per million man hours. Coal mine accident statistics have been described at various times as unacceptable and intolerable and recently resulted in the enactment of massive legislation. The 1969 Coal Mine Health and Safety Act was passed by Congress "to improve the working conditions and practices in coal mines and to prevent accidents and occupational diseases originating in the coal mining industry." The prevention of accidents in coal mines is the statutory responsibility of mining engineers and the moral responsibility of all who have any part to play in mining coal. The questions to be answered by these men may well be - What are the reasons for the high accident rate? Are the mines as safe as they can be? Are our mines sufficiently manned to insure proper supervision of production cycles and safety requirements? Are our plans for safety committees, safety campaigns, and safety inspections sufficient? Are they producing the results intended? If not, how can these be reorganized to have a greater impact? What is the real cost of an accident? What are the immediate and long-term plans for further improvements? These questions are in no way exhaustive, and the answers are not easy. There are many aspects of mine safety, and any one of them can be the subject of a lengthy discussion. The aim of this paper, therefore, is to limit the analysis to documented fatal electrical accidents in mines so that meaningful conclusions for improvement in electrical accident-experience statistics can be made. In doing this, it is also the intention to emphasize areas of missing information and propose a few suggestions for better hazard analysis.

Jan 1, 1972

By MATT RENAUD, Mustafa Kumral

As high-quality mineral deposits are thoroughly exploited, mines of the future will have to move towards more remote and lower quality projects. With these projects comes an increased business risk to the operator. Even now, mining companies often turn to foreign countries for new deposits to produce, introducing the concept of country risk into their portfolio. Furthermore, feasibility studies often fail to accurately quantify the risks associated with various projects, and as such, this study proposes a technique of risk quantification which can both aid mining companies to evaluate the viability of investment and assist in risk disclosure to public investors for the mining industry of the future. This paper aims to quantify the effects of country risk on the valuation of potential mining projects, using a combination of modular and risk-weighting techniques to evaluate the country risk premium (CRP) required to obtain capital for operation of risky foreign mining projects. The techniques proposed in this paper are demonstrated using fictional examples and then evaluated for accuracy against a recently developed debt-funded precious metal project in a country in the Americas.

Sep 30, 2021

By M. J. Virnig, B. D. Boley, G. A. Wolfe, J. M. W. Mackenzie

A flowsheet for the recovery of nickel and cobalt from laterite ores has been developed which involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-I and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent extraction plant and operating conditions are made.

Jan 1, 1999

By J. B. Hiskey

Of the halogens, the gold iodide complexes are the most stable in aqueous solutions. A series of experiments were performed to investigate the kinetics and mechanism of the leaching reaction between gold and iodide. Using a rotation disk technique, the effects of rotation speed, iodide and iodine concentration, temperature, pH and in the presence of different electrolytes were measured. Oxygen and hydrogen peroxide were also examined as oxidants in the iodide system. The first order reaction rate was found with respect to 13 and half order reaction rate with respect to 1-. The comparison of gold leaching between iodide and cyanide is also presented, in which a rate constant of about 2.6x10-9 mol/cm2? sec for 10-2 M I- and 5x10-3 M I2 was obtained. This value is close to that -for typical cyanidation. Cyclic voltammetry experiments were also performed to examine the electrochemical nature of the reaction which will be presented in part II of this study.

Jan 1, 1990

By Arif Emre Dursun, Ali Aras, Hakan Özşen

Specific energy (SE) is defined as the amount of work required to cut a unit volume of rock and is used to estimate the performance of excavation machines. Generally, the SE value is produced from full-scale or small-scale rock cutting tests. However, these tests require expensive equipment and experienced personnel, and the testing procedure is time consuming and impractical. Therefore, for estimation of SE, this study aimed to find a solution to estimate SE using rock mechanics test results and Bond work index values (BWi), which can be produced in a more practical, less time-consuming manner and with inexpensive test equipment. Small-scale rock cutting, rock mechanics and Bond work index tests were carried out on seven rock samples, which can be grouped into two different type of rocks: marble and travertine. In addition, the instantaneous cutting rates (ICR) of a selected roadheader were calculated using SE values. Rock mechanics tests performed in this study were uniaxial compressive strength (UCS), Brazilian tensile strength (BTS), ultrasonic velocity (Vp), Schmidt rebound hardness (RL), corrected point load index (Is(50)) and density (ρ). The simple regression method was used to estimate SE from rock properties and BWi. As a result of this simple regression, a significant and highest correlation was found between SE vs. UCS and Is(50). A good correlation was found between SE vs. BTS, RL and BWi values. A moderate correlation was found between SE vs. Vp and ρ.

Jul 28, 2021

By John C. Harkey

The paper shares programs that presently use the CDC PLATO System to train individuals in industry. A short history of PLATO development; as a training system is presented with reflection on the major training trends being used to improve training effectiveness. A discussion is offered to describe the benefits of using a system for individualizing instruction. An introduction; is offered showing how one can recognize' individual differences, with an explanation of how the strengths of a computer are used to deliver and manage the training. Simulations of hazardous processes are shown to be one of the most effective uses of the computer for training.

Jan 1, 1979

By R. G. Sinclair, E. Sangine, S. M. Fortier, J. Brainard, K. Stone

"The U.S. Geological Survey and Natural Resources Canada conducted a study on the net import reliance of each North American country, and the impact of North American trade on the net import reliance of 12 nonfuel mineral commodities that are associated with advanced technology products: cadmium, cobalt, gallium, germanium, graphite, indium, lithium, nickel, rare earth elements, selenium, silver and tellurium. The combined results for North America, using 2014 data, showed greatly reduced net import reliance for nearly all of the commodities evaluated, which is largely the result of pooling the resources of production and recovery in Canada and Mexico of materials that are consumed in the United States. This study highlights the mitigation of potential supply risk for critical materials that results from trade within the North American trade bloc. IntroductionMultiple metrics and definitions exist for what constitutes a critical material, but there is broad acknowledgment that a mineral commodity may be considered critical if, among other factors, its production is geographically concentrated, if it has few or no substitutes, or if the country of origin is politically unstable. Numerous governmental and independent researchers have proposed methods of investigating criticality, with differing priorities such as economic resilience or strategic military supplies (European Commission, 2014; Graedel et al., 2015; U.S. National Science and Technology Council Subcommittee on Critical and Strategic Mineral Supply Chains, 2016). While criticality really depends on who is asking the question, and despite the differing priorities, there are several commodities that are commonly found to be of concern. In particular, some critical or potentially critical materials are used increasingly in advanced technologies, or they have complicated supply chains because they are coproduced or are produced in controlled markets.Commodities for which imports are required to satisfy domestic demand are those for which the importing country is net import reliant. Net import reliance (NIR) in this study is calculated as the amount of imported material, including changes in stockpiles, minus exports and is expressed as a percentage of domestic consumption:"

Jan 7, 2018

By David H. Carlson

The paper presents background information including data on diesel exhaust pollutants, amounts produced and standards, a desscription of mine characteristics that affect air monitoring techniques and a review of portable measurement techniques and instruments for gas and particulate matter sampling. A general review of the laboratory and field research being conducted at Michigan Technological University in the area of diesel emissions is presented. The facilities involved with this research are also described. These are the Experimental Mine, the diesel dilution tunnel test cell, the Mine Air Monitoring Lab (MAML), the portable instruments and the production mines used.

Jan 1, 1979