Search Documents

By K. M. Mohamed, R. K. Zipf

The shear strength properties of generic cement foam material and cement foam/concrete interfaces were examined at three testing scales. In laboratory direct shear tests on specimens with average shearing area of 0.006 m2 (10 in.2), the cement foam material had average peak and residual shear strengths of 0.88 MPa (128 psi) and 0.39 MPa (56 psi), respectively. Depending on the concrete strength, the cement foam/concrete interfaces had peak and residual shear strengths ranging from 0.71 to 0.81 MPa (103 to 117 psi) and from 0.27 to 0.29 MPa (39 to 42 psi), respectively. In laboratory direct double shear tests on specimens with average shearing area of 0.084 m2 (130 in.2), the cement foam/concrete interfaces had average peak and residual shear strengths of 0.17 to 0.30 MPa (25 to 44 psi) and of 0.11 to 0.23 MPa (16 to 33 psi), respectively. In large shear tests of simulated cement foam seals with the Mine Roof Simulator (MRS) test frame, cement foam/concrete interfaces with shearing area of 1.486 m2 (2,304 in.2) had average shear strengths of about 0.08 and 0.16 MPa (11 and 23 psi) along the roof and floor interfaces, respectively. The average shear strength through the cement foam material was 0.38 MPa (55.3 psi). Finite element analysis of the large seal tests and the back analysis of the shear strength of full-scale cement foam seals conducted at the NIOSH Lake Lynn Laboratory confirmed shear strength of about 0.14 MPa (20 psi) along the seal/rock interfaces. The study concluded that the structural analysis of cement foam seals should be based on their residual shear strength determined from small laboratoryscale tests of the cement foam/concrete or rock interface and not be based on their peak strength.

Jan 1, 2014

By D. I. Smith

Constructing tunnels in congested urban areas requires tunnels to be placed closer together and with less cover than was previously necessary. Contract CQ031 of New York?s East Side Access project will construct four six-meter diameter bored tunnels in a three-up one-down ?T? configuration, with less than three meters of soil between the tunnels. Mixed-face rock and glacial till conditions with a high ground water table will be encountered under active railroad yards. The tunnels will also pass beneath the busiest railroad interlocking in North America with cover as shallow as three meters. This paper discusses the challenges of designing segmentally lined tunnels for these conditions.

Jan 1, 2008

By B. A. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformation. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, timelapse point clouds of mine workings. In order to determine sloughage volumes and locations, two sets of laser scans were performed 42 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds. Volumetric changes of 2.3-2.6 m3 were detected on rib faces during the time-lapse study. In addition, displacement in the mine roof was, as expected, not detected, suggesting well surveyed scans and an appropriate scan resolution.

Nov 1, 2013

By R. L. Grayson, J. R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. Thus far environmental groups remain unconvinced, and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This paper presents a fresh and cogent perspective on coal’s role in sustaining society by anchoring the message in a transparent material flow analysis that links coal’s impacts across a broad range of social and environmental aspects.

Jan 1, 2006

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

By Ma. X.

Passive seismic imaging is applied in underground mining to analyze the stress redistribution after the occurrence of a major seismic event. The velocity model is established to be utilized in velocity inversion. By comparing the images from velocity tomography on two different time scales, the average velocity of a mining area decreases significantly after the major event. It is highly likely that the stored energy level drops due to the occurrence of a major event. Also, total energy stored in micro-seismic events for each day is summed up and the energy change trend is plotted to illustrate the correlation of energy with a major event.

Feb 27, 2013

By Beth Robinson

This first of two articles on the Second Mexican Mining Rail Excursion describes some of the more casual experiences participants enjoyed on last fall’s rail tour of major Mexican mining operations. In this article, Beth Robinson, a graduate student at Colorado School of Mines, describes trip organizers, participants, and some of the unique events occurring during the two-week excursion. Next month, part two of the series will highlight various Mexican mines and plants.

Jan 1, 1982

By Maurice A. Ponti

The D.C. Water and Sewer Authority is implementing the Anacostia River Projects component of its Long-Term CSO Control Plan, including 21 kilometers of 3.7- to 7-meter-diameter CSO near-surface diversion storage/conveyance structures and flood relief, pressurized-face, soft ground tunnels at a maximum depth of 65 meters. This paper describes a project-specific soil grouping system that is primarily based on soil characteristics for tunneling derived from tests including Atterberg limits, grain size, swelling, mineralogy, triaxial, pressure meter, and consolidation, which differentiates the project from past area tunnel projects using descriptive systems based primarily on area geology.

The Pogo Mine, near Delta Junction, Alaska is a 2500 TPD gold operation employing processes including grinding, gravity, rougher flotation, leach, CIP, and E/W. An OCS(Optimizing Control System) expert control system has been implemented on rougher flotation in early 2008. The OCS system communicates with the Plant DCS(Distributed Control System) through OPC(OLE for Process Control) communication. The initial strategy was to control the flotation cell froth level set points to achieve target froth velocities. This strategy was enhanced by controlling both level and air flow setpoints. The flotation cell air and level are adjusted to reach cell pulling rates (froth velocities). The pulling rate setpoints for each cell are determined based on downstream capacity (concentrate surge tank level). The effect of pH and upstream disturbances is also taken into account in adjusting the air and level setpoints. Feed forward compensation is employed down the flotation row to minimize disturbances.

Jan 1, 2009

By T. Arthur Palm, Stephen L. Bessinger

San Juan Coal Co. (SJCC) operates an underground coal mine near Farmington, NM. Continuous miners and a longwall produce 6.3 to 7.2 Mt/a (7 million to 8 million stpy). SJCC is owned and operated by BHP Billiton. The coal seam at SJCC has been shown to have a propensity for spontaneous combustion. As such, during the feasibility study for this project, it was elected to use a bleederless ventilation system on the longwall. Due to the combination of spontaneous combustion, methane liberation and, to a lesser extent, hydrogen sulfide, a typical wraparound ventilation system would not be appropriate. Three-entry gate roads are developed, and the longwall gob is sealed as mining progresses. SJCC uses a nitrogen injection system to continuously inertize the gob.

Jan 1, 2007

By John E. Tilton

During the past several years — much to the delight of producing firms and countries — copper prices have surged from under $1 to more than $3/lb. Anyone familiar with the industry also knows that since the early 1970s the long-run trend in real copper prices has been significantly downward. This sharp contrast between short-run and long-run trends raises the issue of the forces behind these developments. What has been driving short-run prices up and long-run prices down? Simple economics suggests that it is all a matter of supply and demand. When demand is rising faster than supply, prices will rise and vice versa.

Jan 1, 2006

By E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. This is especially true in surface and underground coal and stone mining where large, noisy equipment predominate. Workers in coal preparation and stone processing plants have also been found to be subject to high sound levels that could potentially cause NIHL over prolonged periods of exposure. National Institute for Occupational Safety and Health (NIOSH) researchers have been conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by river dredging. Little is known about the noise environment and worker exposures in these environments, where processing and mining equipment similar to coal and stone are employed. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to identify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges, in several surface mine sand and gravel operations and in the processing facilities. The locations where workers are likely to be overexposed and were found to be most susceptible to noise overexposures are reported. Results indicate that there are areas on the dredges (crane, suction pumps, and diesel engines) where sound levels greater than 90 dB(A) are present. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration (MSHA) Permissible Exposure Level (PEL) of 90 dB(A) TWA8, laborers, mechanics, oilers, helpers, pickers, and greasers are the workers likely to be exposed to hazardous sound levels and thus develop NIHL over time. Knowledge of the equipment noise, area sound levels, and worker dose levels is information that management and employees can use to reduce exposures. Exposures can be reduced in certain areas through administrative controls and through engineering controls applied to the noisiest equipment.

Jan 1, 2008

By M. Baumann

Introduction Gold Quarry is one of the largest gold deposits in Nevada, located along the Carlin Trend, approximately seven miles north of Carlin, NV. Owned and operated by Newmont Mining Corporation, as of December 31, 2005, Gold Quarry had produced over 13 million ounces of gold. Multiple simulations were constructed for gold and metallurgical variables using the Stepwise Conditional Transformation method. Analyses of these simulations have been used for a variety of purposes, including an assessment of uncertainty with various ore types. This assessment provides insight for improved modeling and reconciliation. Geological Framework Gold Quarry is a large, low-grade disseminated gold deposit hosted in Silurian-Devonian aged sediments at the Chukar/Alunite-Good Hope fault intersection. Gold bearing hydrothermal fluids appear to have migrated upwards along the Chukar/Alunite and Deep Sulfide Feeder faults and then moved outward along favorable stratigraphic horizons and structural intersections.

Jan 1, 2007

By G. Danko

MULTIFLUX, a new thermal, hydrologic, and airflow model and software is being developed to solve the flow of heat, moisture, and air in and around an underground opening. MULTIFLUX couples two distinct domains that are solved separately first and re-coupled as an iterative task: (1) the rockmass, and (2) the airway. The airway is solved with a lumped-parameter Computational Fluid Dynamic (CFD) module which is an embedded part of the MULTIFLUX code. The CFD model includes convection, conduction, and radiation for heat, as well as convection and diffusion for moisture transport in an air-filled opening. The CFD model also solves for the airflow field. The surrounding rockmass model may be from any analytical solution, or from a complex thermal-hydrologic numerical model such as NUFT or TOUGH2. The rockmass model is interfaced to MULTIFLUX using a novel technique called Numerical Transport Code Functionalization (NTCF). The method provides fast convergence on a personal computer platform. The paper reports the results of MULTIFLUX simulations for a mine drift, comparing calculations with a known mine climate software, CLIMSIM, and with measured data. Through this validation example, the performance of MULTIFLUX is demonstrated. The results show excellent agreement due to the use of realistic modeling assumptions and boundary conditions.

Jan 1, 2009

By J. L. Carr

Every year, severe injuries and fatalities occur when a miner is struck or pinned by a continuous mining machine, shuttle car, scoop or other piece of mobile mining equipment. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Although hundreds of these systems are installed and in use in operating coal mines, the influence that coal has on the electromagnetic fields associated with these systems has never been rigorously quantified. NIOSH researchers have conducted tests to measure whether the proximity of coal has a significant influence on a popular design of proximity detection system. The system tested utilizes a low frequency magnetic field generator that would be mounted on the mining machine. At the NIOSH Safety Research Coal Mine in Pittsburgh, researchers measured the performance of a simplified proximity detection system of this type first on the surface then underground at varying distances from a coal face. Analysis of these measurements shows that the presence of coal does not have a measurable impact. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By D. L. Ogonowski, J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m(36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached design capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM-800Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

Steady increases in longwall production have required operators to apply greater quantities of ventilating air in an effort to control and dilute respirable dust. Significant increases in shearer speeds necessitate that longwall supports also be advanced at a faster rate. Both of these factors may contribute to overall respirable dust levels on the longwall face because as supports are lowered and advanced, broken material falling from the top of the canopy is entrained directly into the air stream. To address this issue, the Pittsburgh Research Laboratory collected respirable dust samples from four longwall faces to characterize shield-generated dust. This paper investigates the influence of air velocity and shield advance rates on respirable dust levels. Also discussed are engineering controls currently used to reduce shield dust and alternative controls being investigated by the National Institute for Occupational Safety and Health (NIOSH).

Jan 4, 2010

By M. Buxton

Sensor derived data can add value across the mining operating chain ranging from resource definition, extraction, pre ? concentration, mineral process monitoring and assessment of product quality. Most documented studies on the use of sensors in mining focus on specific technologies for specific applications. These studies do not take into account different aims, objectives and operating conditions at different steps in the value chain. The first part of this contribution assesses key physical performance and discriminatory requirements of sensors applied in each portion of the mining value chain. The second part proposes a framework of methods for quantifying the value added by additional sensor information. Integrating the sensor based technology and the economic value quantification allows for both, designing an economically optimal sensor monitoring network along the whole mining value chain and optimizing efficiencies. Illustrative studies demonstrate the significant economic benefits, in particular in reduction of exploration expenditures, increase in extraction efficiencies, increase in ore product quality and improvement of processing efficiencies.

Feb 27, 2013

By Sakai Kunito, Nigel B. Sugden

If an Earth Pressure Balance (EPB) TBM is operated effectively tunneling can be carried out producing negligible ground movements. Using the methods given in this paper face losses of the order of 0.5% and less are generally obtainable using an EPB. Operating the EPB TBM in this manner reduces the requirement for the building protection measures used to protect surface structures. This can result in a considerable cost saving for the construction of a tunnel under built up areas. This paper to give guidance on the causes of ground movements around a TBM and the methods of running an EPB TBM that will minimize those movements. Details of how this was successfully done during the construction of the Bangkok Metro are given. The paper is split into three parts as below. 1.Causes of ground movements due to TBM tunneling 2.Methods of controlling those movements using an EPB TBM 3.Case history Bangkok Metro (water main)

Jan 1, 2001

By M. Schafer

The 20 foot diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT-3) has been completed. This paper will summarize aspects of liner design and address the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented.

Jan 1, 2008