Search Documents

By H. Walqui

This paper describes operating gains resulting from standardizing operating and maintenance practices to improve the performance of the pebble crushing circuit at he Empire Concentrator. Past efforts have led to improved operating time but no additional throughput gains. New Operating standards and checklists were developed and introduced. The content and frequency of the review process indicators was then changed to take advantage of the new practices resulting in an increased feed rate and availability through the pebble crushing circuit.

Feb 27, 2013

By H. R. Manouchehri

"Pyrrhotite (Po) is one of the most abundant sulfide minerals in processing industry and must be rejected in most cases. Particularly, Po rejection and its selectivity against pentlandite (Pn) have long been a challenge due to similarities in the mineral composition of the two minerals and the collectorless flotation characteristics of Po. Xanthates have been widely used to promote sulfide mineral flotation; however, in the presence of xanthates, the redox potential established at the mineral/solution interface is most important, determining the flotation performance. In this paper, the importance of electrochemistry in Po and Pn flotation has been demonstrated and a comprehensive study was conducted on two different feed streams (i.e., magnetic concentrate and scavenger cleaner streams, containing magnetic and nonmagnetic forms of Po, respectively), from Vale’s Clarabelle Mill in Sudbury, Ontario, with an objective to determine if improvements in Po rejection and Pn recovery could be achieved by controlling pulp electrochemistry. By conducting a series of flotation tests under different Eh conditions and reagent usage schemes, it was revealed that higher Po content in the magnetic stream may protect Pn from being oxidized, improving Pn recovery. The results indicated that at low oxidizing pulp chemistry, the rest potential for the Pn is still high enough to allow the formation of dixanthogen to promote its flotation. Using a Pt electrode, it was found that by controlling pulp potential at -50<Eh< +50 mV, the Pn recovery and Po depression would be satisfactory. The results, using mineral electrodes (Outotec Chena analyzer), indicated that selective separation can be achieved if low-to-moderate oxidation potentials (0 to 100 mV) or reduction (0 to -100 mV) potentials are monitored using Pn and Po electrodes. Mixing two streams at 50:50 wt % would be possibly beneficial in selective separation.IntroductionPyrrhotite (Po), Fe1-xS, is one of the most abundant sulfide minerals in the processing industry. It is an iron-deficient sulfide that occurs either in monoclinic or hexagonal form. The monoclinic one is richer in sulfur and is ferromagnetic, whereas the hexagonal Po is poorer in sulfur and has no magnetic properties. In general, the ferromagnetic properties of natural Po increase with increasing sulfur content. Although Po holds significant iron content, it is not used as a feedstock for the iron and steel industry due to the difficulty in achieving complete removal of sulfur. The common availability of iron oxide ores makes the iron sulfides irrelevant for the steel industry."

Jan 1, 2015

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the U.S. National Institute for Occupational Safety and Health collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants revealed not having a systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. In this paper, we identify and describe three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication and specialized training, to increase awareness of imminent danger situations. IntroductionIn recent years, the metal and nonmetal mining sector, as categorized by the U.S. Mine Safety and Health Administration (MSHA), experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured, twice the number of fatalities in each of the previous two years (MSHA, 2015a). As a way to address this increase, MSHA issued its P15- IV-01 program policy letter, suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners” (MSHA, 2015b). The goal of these examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 9, 2018

By L. Alan Weakly

Global warming is a political reality in the United States today. The actual impact of the continued utilization of fossil fuels is not known and is open to debate. However, the growing concern about the continued use of these fuels is problematic. There are technologies available to us today that would permit America to meet its future energy demand and not contribute to global warming. The inconvenient reality is that fossil fuels cannot completely be replaced with energy conservation and the use of wind, solar, hydroelectric, geothermal and nuclear energy. The connection between the greenhouse effect and global climate change was first identified by physicist John Tyndall in the 1860s. To prove the greenhouse hypothesis, Roger Revelle and his research team started measuring carbon dioxide concentrations in the earth?s atmosphere in the early 1960s (Becker, 2007). With the rising concern about global warming, scientists throughout the world have been obtaining surface and air temperature data. Scientists have also been comparing CO2 concentrations found in glaciers throughout the world with theorized annual temperatures. Data for both dates back 1,000 years. Armed with this data, many nations of the world and the United Nations Intergovernmental Panel on Climate Change (IPCC) have concluded that climate change is a reality. The IPCC also concluded that this climate change is the result of mankind?s consumption of fossil fuels and that catastrophic consequences will occur on a

Jan 1, 2008

By Verya Nasri

The Silver Line Phase III Project is the final one mile underground segment of the new Bus Rapid Transit in downtown Boston. The project is expected to significantly reduce existing and anticipated traffic congestion. The twin one-lane tunnels and two station platforms will be built by NATM in Boston saturated soft clay, sand and till layers in proximity to several historical buildings, underpinning two existing cut and cover subway stations and several major utilities in densely built urban area. This paper presents the analysis and design of the NATM tunnels and stations detailing the excavation sequence and support system and various ground improvement and pre-support techniques used in the preliminary and final design of the project

By D. Lauriski

The recent spate of catastrophic events at U.S. mines raises the question as to whether or not the mine safety and health system in the U.S. is broken. The prescriptive regulatory regime in the U.S. is not a cure-all for a broken system. Without totally dismissing the contribution of a prescriptive regulatory approach, this paper argues that safety in the U.S. mining industry would be enhanced if the nation adopted a scheme that provides a balance between specification standards and two alternatives: performance and systems-based standards. This would allow effective and flexible means to continuous health and safety performance improvement. Mine operators, regulators and politicians could then go beyond thinking that compliance alone equals strong safety by creating a proactive system that emphasizes continuous improvement. By adopting performance and systems-based standards, exemplary safety and health performers can be recognized, allowing regulators to focus their efforts on those without sound occupational safety systems and who have substandard safety performance. Mining Engineering, 2011, Vol. 63, No. 7, pp. 77-82. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Andrea Koschinsky, Peter E. Halbach, Margret Halbach, Andreas Jahn

"Ferromanganese crusts contain hydrous Mn and Fe oxides as main metal compounds together with some economically interesting minor elements such as Co, Ni, Ti and Cu and trace metals such as Mo, W, Nb, Te, Ga, Pt, and REEs. Some of these metals or semimetals have a great future potential as innovative high-technology constituents. All of them are highly enriched in the crusts compared to seawater composition.The Mn in the crusts mainly originates from the O2 - minimum zone in the oceanic water column. The agent for Mn2+ oxidation is dissolved oxygen, transported upwards from colder deep water layers by turbulent eddy diffusion. The Mn itself descends from surface waters and is carried down to the O2-minimum zone by fecal pellet transport. In contrast, Fe is mainly supplied from carbonate dissolution of planktonic skeletons in the water column. These relationships result in the fact that the oceanic water depth strongly controls the metal composition of ferromanganese crusts: the Mn - group metals are more enriched in shallower water, whereas the concentration of the Fe - group metals increase with water depth. The REEs play a very important role with regard to the trace metal composition of the crusts: their concentrations increase with water depth mainly controlled by a decreasing Mn/Fe ratio.In seawater, REEs occur as carbonate complexes; preferably, the light rare earth elements (LREEs) form REECO3 +(aq) and the heavy Rare Earth Elements (HREEs) REE(CO3)2 (aq) complexes. The REEs are transition metals, their 6s orbital of the outermost shell is filled before the filling of lower 4f electron shells is completed, thus the configuration of the valence electrons is similar in all the REEs, and all REEs exhibit similar chemical behavior and exist, dominantly, as 3+ cations. The ionic radius decreases progressively from La3+ (1.18 Å) to Lu3+ (0.97 Å), this phenomenon is called "lanthanide contraction". Due to the fact that REEs in seawater form cationic and anionic carbonate complexes, the two main hydrogenetic constituents, hydrous !-MnO2 and Fe-oxyhydroxide, fractionate the group of REEs by surface absorption processes. According to the pHZPC-concept the ?- MnO2 phase has an electronegative surface, and Fe-oxyhydroxide a slightly positive surface charge at seawater pH. These relationships are the main reason for the observed REEs fractionation."

Sep 1, 2014

By D. Campos, J. M. Macedo, S. Chadwick

The incorporation of low cost technology transfer to increase the ability of locals to acquire and maintain long term employment are key ingredients for sustainable industrial development. Alcoa’s Alumar plant on the island of Sao Luis is the largest and most modern refinery/smelter complexes in northern Brazil. The plant has one of the most advanced Environmental, Health, and Safety management process in the aluminum industry. Technical assistance, training and financial support were made available to Alumar to address social sustainability issues. Through several programs led by employees on a voluntary basis and applying intensive and extensive training programs, Alumar has enabled local people to develop skills on agriculture and land management, wastes minimization, small business development and administration, all based on sustainable development and social responsibility concepts.

Jan 1, 2004

By J. B. Seymour

This paper provides an overview of the current use of backfill for ground support in underground metal mines in the United States and a summary of recent accident data reported for these mines by the Mine Safety and Health Administration (MSHA). Backfill mines comprise a major part of the underground metal mining industry and are particularly important in terms of the fatalities and injuries impacting this workforce. Ground falls are the leading cause of fatal accidents at these mines accounting for 50 percent of the total fatalities (4 out of the 8 fatalities that occurred from 2006 through second quarter of 2011). MSHA reported several different types of accidents involving backfill at these mines. While backfill ground falls do not occur frequently, these accidents result in a much higher proportion of fatalities than host rock ground falls. Backfill ground fall accidents are especially hazardous in underhand cut-and-fill mining operations where employees work directly beneath the backfill. An analysis of recent MSHA accident data supports the need for further cooperative research with the mining industry to identify and address ground control problems in underground metal mines using backfill.

Feb 27, 2013

By Hiroshi Soda, Atsumi Ohno, Hiroyuki Yamazaki, Alexander McLean

INTRODUCTION The method of heat removal during a casting process strongly influences the crystal morphology of the cast product and hence the metallurgical and mechanical properties of the solidified materials. In this paper, the Ohno Continuous Casting Process (OCC) is described in terms of the casting conditions and the type of structure observed in the cast product. Significant improvements are observed in workability, fatigue strength and corrosion resistance of castings produced by the OCC method, Ohno (1988). Applications of this technique to low melting point nonferrous metals and alloys are discussed. The feasibility of the application of this technology to high melting point materials is outlined. THE OCC PROCESS The OCC process involves delivering liquid metal into a heated mold, the temperature of which is held just above the solidification temperature of the metal to be cast. This is the key point which differentiates the OCC process from the conventional continuous casting method. A schematic illustration of the OCC process is shown in Figure 1. The Formation of a Single Crystal When the mold is heated above the solidification temperature of the metal to be cast, nucleation on the mold surface is prevented and solidification takes place only at the mold exit. The heat is extracted through the product being cast by a cooling device located near the mold outlet. Crystals are formed only at the tip of the dummy bar at the start of casting, and as the dummy bar travels away with a progressively increasing speed from the mold, the position of the solid liquid interface will align with the mold exit, producing a unidirectionally

Jan 1, 1990

By I. J. Duckworth

Due to improved, stringent safety regulations, many modern road tunnels are statistically safer, per kilometer, than above ground roadways. However, the public perception and reaction in the event of a serious tunnel fire is very different to that associated with a surface incident. Vehicle fires in road and rail tunnels are recognized to represent an immediate and extreme danger to the patrons of those systems. Unlike workers in the mining and civil construction industries, the general public are neither trained nor equipped to fight fires or evacuate under deteriorating smoke conditions. Accordingly, for the majority of modern transportation tunnels the ventilation infrastructure is sized on the requirement to control the combustion products from worst-case fire scenarios and to provide a tenable evacuation route for the tunnel users. It is common for these same emergency ventilation systems to be employed, often in a reduced capacity, for other operating modes such as the dilution of pollutants during congested traffic conditions. This is one of the fundamental differences to mine ventilation, where primary ventilation systems are not typically sized based on fire scenarios. This paper presents an overview of the subject of fires in vehicular tunnels. This includes a brief history of major transportation tunnel fires followed by a discussion on the resulting legislation and standards that govern the design and operation of tunnel emergency ventilation systems. A summary is provided on the common criteria, theory, and design techniques that are employed during tunnel emergency ventilation systems design. Information is provided on fire detection and suppression, with a discussion on the growing acceptance of wet suppression as a means to mitigate major fires in road tunnels worldwide.

Jan 1, 2009

By J. Hollow, D. Walsh

The Fort Knox Mine is located in Alaska’s interior, where the average ambient air temperatures range from -24oC in January to 16oC in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and a conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leach, carbon adsorption and cyanide destruction kinetics. Additionally, an energy balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post project plant performance that validates the model and shows the mine produced an additional 596 kg (19,155 ounces) of gold, while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By E. Carvajal I

Large diesel engines provide the mining industry the substantial power and torque needed to move large amounts of material efficiently. But the stresses generated by such power and torque necessitate complex maintenance programs to ensure the utmost operating capabilities are not compromised. Of all its available sensors, the Exhaust Temperature differential between the right and left banks can provide the most valuable indicator of the overall operating condition and potential degradation of a large diesel engine. BHP Billiton Escondida Mining has implemented real-time remote monitoring, diagnostics, reporting, and tracking of Exhaust Temperature differential using Modular® technology. As a result of the processes and procedures put into place surrounding their MineCare maintenance management system, Escondida has proactively replaced over 300 injectors, resulting in an increase of 4% in Engine availability.

Jan 1, 2011

Federal regulations require the use of methane monitors on all mining machines. All machine-mounted methane monitors currently used in underground coal mines rely on catalytic heat of combustion sensors. As a comparison, although not currently approved for use on underground mining equipment, instruments with infrared sensors are evaluated in this study. Potential advantages of using infrared sensors include faster response time, long-term stability, and reduced maintenance needs. Tests conducted in the laboratory and at a full-scale model mine compare the performance of catalytic heat of combustion and infrared sensors operating under test conditions designed to simulate airflow conditions underground.

Jan 1, 2009

The ventilation conditions at the underground coal mines are influenced; first: by the disturbances of the natural nature (barometric pressure, methane liberation, etc.), and second: by the disturbances caused by the production process. The major goal of this study was to determine the changes of the ventilation parameters, such as the flow, pressure and methane concentration around the longwall panel, particularly, along the longwall face due to the shearer operation (motion). It is well known from the practice, that the movement of the shearer influences the ventilation parameters around the longwall panel, including the gob area. Until now, these data were gathered in a single or multiple locations at the different time. However, only the simultaneous measurements of all of these values allow seeing the time dependent interrelationships between measured parameters. To be able to show these interrelationships, special experiments, described in this paper, were carried out by the author. These experiments were prepared and executed at the BUDRYK Coal Mine in Poland. During each experiment a simultaneous measurements and monitoring of the barometric pressure, air velocity and methane concentration at the different locations along the longwall face, were performed. The investigation was possible by using a special setup of instruments with a short sampling time, i.e., within 2 seconds. The monitoring of the absolute pressure was conducted by using the digital barometer µBar, developed by EMAG, based on the SETRA pressure transducer, model 470. The velocity of air was measured using the electronic vane-anemometers, developed by IMG-PAN. The methane concentrations were measured using methanometers as the part of the EMAG automatic gas monitoring system. The investigation data confirmed that disturbances due to the operation (motion) of the shearer at the longwall face have a local character. It could be also seen that a large diameter shearer (compared to the total cross-section area available for the air flow) is acting as the piston compressing the air (the overpressure) ahead of the shearer. This fact affects the methane mixing process and flow patterns in the vicinity.

Jan 1, 2009

By C. C. Hamilton, G. R. Lane

Traditionally, mineral sands are evaluated by preparing several mineral products using a combination of heavy liquid-, magnetic-, and electrostatic methods. Whole-rock assays (WRA) are then conducted on ilmenite, rutile and zircon products in order to determine trace element contents, which may affect project feasibility. Combined methods can be time consuming, expensive and even outdated due to the use of banned and toxic chemicals such as clerici solution. Coupled with large field-sample quantities, these procedures can potentially introduce unacceptable sampling and related errors. Modern mineralogical analysis techniques can provide complete mineralogical inventories on a single THM product, reducing the amount of processing involved in satisfactory characterization of early exploration samples. A small exploration sample can be processed to produce a small THM concentrate using readily available gravity/density methods. In turn, the THM product is submitted for Whole Rock Analysis (WRA) and mineralogical inspection by X-ray diffraction (XRD), and microscopic evaluation. Modal mineralogy and textural data can be determined using optical methods, automated image analysis, and scanning electron microscope (SEM) based systems. Benefits of automation are reproducibility and the capability of rapidly analysing thousands of particles as opposed to manual optical methods. Automated systems include the use of Automated Digital Image Analysis (ADIS), and SEM-based systems such as the Mineral Liberation Analyser (MLA) and QemSCAN. For detailed mineral chemistry, microanalysis techniques ranging from electron microprobe (EMPA) to Secondary Ion Mass Spectrometry and Laser Ablation Mass-Induced Coupled Plasma-Mass Spectrometry (LAM-ICP-MS) are used. Examples of these automated and analytical methods are presented. ADIS at SGS-Lakefield Research uses optical characteristics to identify and measure mineral species in THM samples; rutile, pseudorutile, ilmenite and leucoxene can be distinguished. Analysis of a single THM product provides bulk modal mineralogy and grain size distribution of particles and the individual mineral grains. Textural information is also obtained detailing mineral associations as well as degree of alteration. Where textural and chemical resolution renders mineral identification ambiguous, SEM-based methods offer better resolution. Examples of this ambiguity are shown in this paper, which leads to QemSCAN as the preferred method where within-grain variability is concerned. Sampling and measurement strategies are followed to meet study objectives, providing a value-added framework for a sequential, cost-effective strategy, which will meet due diligence and bankable accreditation criteria. Studying a THM product by electron microprobe and LAMICP-MS may reveal potential fatal flaws related to mineral chemistry. Low detection limits in the range of 200 to 500ppm are possible using electron microprobe analysis for suitable matrixes (U, Th in zircon). For the detection of ultra low level elemental contaminants, LAM ICPMS is the most accurate method of evaluation. Elements including U, Th, La, Ce, Nb, and V in Ti-minerals can be determined down to 50 ppm.

Jan 1, 2005

By W. Burger

Mechanical excavation methods can significantly improve excavation performance and labor safety compared to drill and blast operations. Herrenknecht has developed a mechanized shaft sinking method for soft and medium strength rock. This system combines innovative technologies which allow simultaneous excavation, removal of cut material and the installation of rock support. This Shaft Boring Roadheader ?SBR? is flexible in diameter and can be used in shafts with changing diameters and different shaft support requirements for depth up to 2,000 m. During regular excavation personnel are not required to access or work on the shaft bench. The boom used to cut the shaft profile is based on roadheader technology.

Jan 1, 2012

By K. Freytag

The extraction of lignite in open-cast mines has a severe impact on the landscape. Proper landscaping after the shut-down of the mines has always been the statutory responsibility of the mine operator. The large area of the land used for open-cast lignite mining requires special regional planning procedures well in advance of the permitting procedure stipulated in the mining law. The lignite plan determines, among other things, the objectives of land reclamation. These objectives will then be outlined in more detail in the mine operation plans and implemented accordingly. Apart from the actual mining laws and regulations, a large number of environmental laws also determine the process of land reclamation. The success achieved in the field of land reclamation in all mining regions during the recent decades has shown that the lignite mining industry creates new landscapes that do not leave any scars in the countryside and merge very well with it.

Jan 1, 2005

By J. V. Ghelarducci, M. A. Sharpe, D. G. Chedgy

This article presents a novel design, called the Climax, High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 ~ 660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax, magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Feb 24, 1997

By Chelsea Woodward

The Spokane Research Laboratory of the National Institute for Occupational Safety and Health has demonstrated a prototype hydrogen-fueled mining vehicle as an alternative to diesel equipment in underground mines. Safety and control systems were added to allow a 70-kW rubber-tired hydrogen vehicle, originally developed by the U. S. Bureau of Mines and Hydrogen Consultants, Inc. (now Hydrogen Components, Inc., of Littleton, CO), to be tested. This work began in late 2000 and culminated with a Mine Safety and Health Administration fire safety review and field tests at the Stillwater Mine in Nye, MT, in 2004.

Jan 1, 2006