Search Documents

By Ralph A. MacMillan

Electronic systems introduced for haulage equipment in recent years probably exceed what mine management is prepared to use. Haulpak trucks alone are equipped with General Electric's Statex III drive system controls, Detroit Diesel's DDEC, Cummins' Centry engine management system and the Haulpak Management System (HMS). The future holds promising developments of even more sophisticated electronics that will lead to unmanned truck operation and control. Trolley-assist will finally come into its own due to the importance of environmental issues, as well as the high potential for increased productivity with dramatically lowerfuel consumption. All of these high technology systems do not mean much unless they add value to mining operations. Some of the benefits that can be expected from these systems are reviewed. In the near future, haul truck control and monitoring systems will be fully linked by telemetry to a mine's dispatch system, as well as to its maintenance management information system. The manufacturer and distributor can also be kept in the communications loop, so that they can better serve customer needs. Portable computers will allow technicians to talk to machine systems to quickly locate a problem, look up service information, check what parts are required and electronically order them.

Jan 1, 1994

By A. Giblett, J. Shuttleworth, R. Dunne

In a previous paper (Dunne, Martins, Goulsbra, Chittenden 1997), the new gravity circuits at Telfer Gold Mine, which incor­porate Knelson centrifugal separators in both the sulphide and oxides, are described. The advantages of the new circuits over the replaced spiral ( oxide circuit) and jig (sulphide circuit) were discussed, as were the improvements in gravity gold recovety. It is of note that the installation of the centrifugal separators in themselves did not result in increased gold recovery. The realisa­tion that changes in gold room practices are required to take advan­tage of the increased fine gold recovery from the Knelson concen­trator was an important step towards improved gravity gold recov­ery. This was achieved by increasing the time taken to treat the Knelson concentrate on the shaking table in the gold room. Although this increased gold recove1y, it was found that the table tailings, especially from the sulphide circuit, still contained high values of gold. In an effort to ascertain ways in which gravity gold recovery could be fu1iher improved, a sample of the sulphide table tailings was sent to the Oretest Laboratory in Perth for testwork. The results from this program are discussed in this paper.

Jan 1, 1998

By Jeffrey M. Christian

Gold prices are rising, in what is coming to be seen as the beginning of a longer term upward trend. After languishing between $325/oz and $364/ oz from early 1991 into early 1993, prices began rising in the first half of 1993. Gold rose from a low of $326/oz in March 1993 to $414/oz on an intraday basis in early August. There was a speculative sell-off at that point, which took gold prices quickly back down to $350/oz briefly in October 1993. At that time, there still was a fair degree of skepticism about gold's price prospects. Many banks believed that gold prices could not mount a sustained rally. As prices dropped in August and September of last year, these suspicions seemed to be confirmed. Gold prices quickly rebounded, however, reaching $395/oz by early January 1994. The strength of this renewed increase led many banks, investors and others that had held negative views of gold to grow more positive. They began buying gold and trading it from the long side of the market. The result was that gold prices remained strong during the first quarter of 1994, trading between $375/oz and $390/oz.

Jan 1, 1994

By William A. Kneller

A considerable range of composition exists in rocks that have been described as chert, jasper, or flint. Their composition may be opaline, chalcedonic, quartzose, or mixed. Certain cherts, when incorporated in concrete, are known to possess nondesirable thermal and chemical properties. The inability of chert to withstand thermal shock above the freezing temperature of water is an example of such a property. Cryothermal reactions may cause disintegration of concrete, due to repeated cycles of freeze and thaw. Thermal properties are significant because small temperature changes may cause inordinate expansion and resultant fissuring of concrete. Freezing of entrained water in chert may cause excessive physical failure in concrete. Some cherts react chemically with alkalies liberated during the hydration of the cement, with resultant cracking and deterioration. Sources of concrete aggregate in Ohio have been viewed with suspicion because they contain considerable chert derived from Middle Devonian and Pennsylvanian carbonate rocks. Light-colored porous cherts from the Middle-Devonian Colum- bus Limestone exhibit the least freeze-thaw durability of the samples studied. Denser cherts may also yield to freeze-thaw stresses, but tend to be more susceptible to thermal shock. Cherts rich in opaline and chalcedonic silica usually exhibit alkali-aggregate reactivity.

Jan 1, 1966

By Charles Rubin

Mining is a capital- and labor-intensive business, and profitability often depends on the ability to squeeze maximum efficiency out of every piece of equipment to achieve safe production. This means keeping every mechanized drill, loader, truck and bulldozer operating at all times, and having a system to coordinate the movements of people and personnel. Mines often use wireless radios to connect equipment with management systems. But growth and changes in a mine?s profile over time can require upgrades to the wireless network. In its openpit gold mine near Carlin, NV, Newmont Mining Corp. has recently upgraded to microwave radio systems to increase bandwidth while maintaining round-the-clock uptime on its wireless network. For many of its operations around the world, Newmont uses Minestar, an operational control software system that allows administrators to dispatch equipment operators and use GPS to track the precise position of every piece of equipment in an operation. Each of the approximately 150 pieces of equipment at the mine has a radio on board. These radios connect to a network backbone that carries information between the equipment and the mine?s operations center. When traffic began to bog down on this network, Newmont upgraded to Exalt microwave backhaul systems to carry dispatch, inventory and control information throughout its operation.

Jan 4, 2010

By D. M. Wyslouzil

Conditioning, in the conventional sense, means providing sufficient agitation and contact time for the reagents to react with the minerals in the ground ore. High intensity conditioning (HIC) on the other hand, as described in this paper, recognizes the need to exceed this minimum power input over a suitable length of time to induce aggregation of the finest size fraction. Time alone is not sufficient to achieve aggregation. The threshold minimum power input, kW/m3, depends on many surface properties of the fine particles and can vary considerably. In addition, the mechanical aspects and the chemical conditions must be matched to achieve good aggregation. Treatment of complex sulphide ores, requiring fine grinding for liberation, offers a large field for the application of HIC. Improved flotation rates and enhanced selectivity are some of the benefits that can be expected. This unit operation has now reached the level of commercial application. Lakefield Research considered HIC not from a fundamental point of view but as a means of solving difficult mineral processing situations arising in actual operating plants. This paper summarizes the effects of the various chemical reagent combinations that had been applied to promote faster, more selective flotation, higher mineral recoveries and cleaner separations, using HIC.

Jan 1, 1995

By E. Forssberg, T. Nordquist

Introduction In this technical note, pilot-scale tests with two types of gravity concentrators, the Knelson separator (Anon., 1983; Forssberg and Johansson, 1984) and the Mark VIIA Reichert spiral concentrator (Balderson, 1982; Forssberg and Johansson, 1984), are described. The experimental work was concentrated on the relatively untried Knelson separator. The materials tested have different concentration characteristics: one was an artificial ore with excellent liberation characteristics and with a wide difference in density between valuable and gangue minerals; the others include a spiral concentrate containing gold from the gravity circuit of Boliden, Sweden, an old scheelite tailing from Yxsjöberg, Sweden, and an auriferous ore, containing gold, that had not been crushed to full liberation. The latter three materials contained other heavy minerals, e.g. pyrite, that can interfere with concentration. Knelson separator The Knelson separator is a compact centrifugal separator with an active fluidized bed to capture heavy minerals. A centrifugal force equal to or exceeding 50 times the force of gravity acts on the particles. The strong centrifugal force traps the heavier particles in a series of rings located in the concentrator while gangue particles are flushed out (Fig. 1). The particular separator used in the tests has a 15-cm (6-in.) diam bowl and can process between ~70 and ~250 kg/h.

Jan 1, 1988

By Richard A. Bideaux

In mid-1975, the United States Borax & Chemical Corp., a member of the RTZ group, engaged Computing Associates, Inc. (CAI) in a continuing project to model their operating property at Boron, CA, with the goal of computerized assistance in medium- and long-range open-pit mine planning. Their property, 161 km (100 miles) northeast of Los Angeles, is the largest producer of borate minerals in the world. Because of unusual geological complexity, this unique deposit presents interesting problems in computer modeling, compared with the coal, uranium, and other metallic deposits with which CAI ordinary deals. Mine planning for Boron has historically been based on manually plotted contour plan maps and cross sections, with geological reserves derived from manual triangularization of the drilling pattern. Standardization and reproducibility of log interpretation, contouring, and reserve calculation were principal goals of using the computer. Additionally, it was desired to shorten both the time and cost of a planning cycle, while at least equalling the accuracy of the manual planning. The present recovery plant processes only water-soluble borates; at some time in the future it will be necessary to recover acid-soluble borate minerals as well. With computer assistance the economics of this changeover point can be more thoroughly evaluated.

Jan 1, 1979

By S. P. Banerjee

Injection of inert gases to combat mine fires has been practiced in various parts of the world for a long time. Of late, nitrogen has become the preferred inert gas for control of mine fires and safe salvage of longwall equipment as compared to carbon dioxide or fuel gases produced from burning of fuel. In India, carbon dioxide has been used for fire fighting in a number of mines during the 1960s and 1970s. More recently inert gas produced from burning of fuel oil in surface plants has been used in controlling the atmosphere in fire areas in two mines. In yet other cases, liquid nitrogen has either been poured directly into fire areas in liquid form or injected in gaseous form to keep the fire in check. Nitrogen produced in liquid form in an oxygen plant is more costly than nitrogen produced from PSA (pressure swing adsorption) based plants. A PSA-based plant has been installed in one of the Indian mines in 1986 and more are in the offing. This paper reviews the application of various inert gases in Indian mines and discusses the likely trend of inert gas application in Indian mines in the future.

Jan 1, 1987

By J. D. Morgan

Introduction In 1987, the US economy continued to grow steadily, reaching an annual rate of $4.6 trillion in the last quarter. The value of domestically processed mineralbased materials rose slightly to $250 billion. The value of US metals rose sharply to more than $7 billion. Industrial minerals rose slightly to $18 billion recycled scrap was valued at $4 billion. Metal prices rose sharply toward year-end. A number of mining and metal companies experienced increased profitability, fostering more optimism about the future. Consumer demand strongly affects mining because the US economy is relatively saturated with long-lived products. Consumer, mortgage, and federal debt continue to rise. 244 million citizens already possess 170 million licensed motor vehicles and 100 million dwelling units. New car production fell 9% to 7.1 million units, but truck and bus production rose 9% to 3.8 million units. New housing starts fell 10% to 1.6 million units. Excess productive capacity exists not only in the US, but also in many other countries. Consequently, the US mineral industry is encountering stiff competition from others, as well as increasing competition from newer engi¬neered materials. Domestic production of plastics rose 9% to 25 Mt (27 million st) - on a volume basis, double all metals. Some 7% of petroleum goes to make petrochemicals including plastics. Imports of nonfuel mineral-based materials in 1987 were valued at $37 billion and exports at $24 billion. Imports supplied a significant proportion of total US consumption of several important mineral materials, including many classified as strategic and critical. In December, the Congress mandated that any major changes in stockpile goals be made only by law, and that the Department of Defense submit annually detailed stockpile supply/demand analyses. Concern about apartheid in South Africa continued, resulting in increasing interest about chromium, manganese, platinum-group metals, cobalt, vanadium, and gold. The National Critical Materials Council continued to monitor the US materials position. The Defense Production Act, authorizing priorities and allocations, supply expansions, voluntary agreements, and the National Defense Executive Reserve continues in effect through Sept. 30, 1989. Under the DPA, the US Bureau of Mines maintains the Emergency Minerals Administration. Further consultations were held with Canada to strengthen the North American defense industrial base. Coal production, 60% from open pits, rose 2% to 825 Mt (910 million st) valued at $21 billion. Nearly four-fifths was burned to generate 56% of US electricity. Exports included 42 Mt (51 million st) of metallurgical coal and 24 Mt (27 million st) of steam coal, with a total value of $3.3 billion. Domestic petroleum production fell 5% to 480 Mm' (3 billion bbl). Uranium mining, including recovery from phosphates, fell 4% to 5.9 kt (6500 st). Nonfuel minerals Major metals: Raw steel production - a major consumer of many minerals - rose 7% to 79 Mt (87 million st). Domestic iron ore production rose 11% to 44 Mt (48 million st), about 96% pelletized. Net imports, though, fell 8% to 11 Mt (10 million st). Raw steelmaking capacity fell 6% to 102 Mt (112 mil-

Jan 5, 1988

By Jon J. Kellar

The adsorption of oleate at the surface of a fluorite single-crystal internal reflection element has been investigated using Fourier transform infra-red/internal reflection spectroscopy (FTIR/IRS). The application of this innovative experimental technique has added a new dimension to the investigation and understanding of collector adsorption phenomena. It is now possible, for the first time, to measure in-situ and in real time the adsorption density and bonding nature of collector species adsorbed at mineral surfaces. In this regard, oleate adsorption densities were calculated from spectral data, and the equilibrium adsorption isotherms were found to agree quite well with other adsorption isotherms reported in the literature. At low equilibrium oleate concentrations(<10-5 M), monolayer-type cover-age was observed in the chemisorbed region. It was found that in this region the adsorption density increases with an increase in temperature, which sup-ports experimental results from previous ex-situ FTIR studies and thermochemical studies in which it was shown that the chemisorption reaction was endothermic. At higher equilibrium oleate concentrations (>10-5 M), the adsorption density increases dramatically at the point of surface precipitation. The oleate adsorbed in the chemisorbed region has a distinctly different spectrum than the oleate adsorbed in the surface precipitation region of the adsorption isotherm. In the chemisorbed region, the oleate appears to be mono-coordinated at the fluorite surface.

Jan 1, 1989

By Norbert Patzelt, Johann Knecht, Wolfgang Baum

The principle of high-pressure interparticulate comminution has been used very successfully since the mid 1980's for grinding a wide range of different materials. A number of reports about operating experience have already been published. High-pressure grinding rolls (HPGRs) are currently making their debut in the mining industry. Experience is being gained with test machines, particularly for the comminution of hard rock. In the grinding of diamond-bearing ore, (Fig 1) interparticulate comminution has already become the standard for liberating the diamonds from the matrix. The advantages of interparticulate comminution are also recognized for the grinding of concentrates (chrome ore, iron ore). Numerous HPGRs are being used very successfully in this field. A testing plant for first-time industrial grinding of coarse, very hard and highly abrasive copper ore was built at Cyprus Amax's plant in Sieretta, Arizona (Fig. 2). The operating experience gained here showed that the grinding of very hard ores places particularly high mechanical demands on the mill. While the machine itself meets the high availability requirements, the wear-protection system proves to be the most sensitive point. Naturally, the properties of the ore to be ground exert a considerable influence on the lifetime of the grinding rolls. This paper describes the wear mechanisms and the wear­protection systems designed to combat these.

Jan 1, 1997

By Kathleen A. Altman

INTRODUCTION The basic premise of the ideas presented in this paper are as follows: Engineers believe that "theoretically" it will work. Operators ask what they must do to make it work. And, people can screw it up. r Today the challenges conf onted during the engineering, startup and operation of mines are becoming more complex. As mining and processing professionals, we are called upon to trav­el all over the world, are subjected to a wide variety of climates and must deal with a numerous cultures and people. Historically, for the majority of the people working in the mining industry, the primary challenges related to projects have focused on the differing perspectives of the disciplines involved. For example, geologists focus on resources and reserves, mining engineers relate to tons or tonnes, metallurgists count ounces or pounds or kilograms of product, mechanics emphasize availabil­ity, human resources personnel deal with absentee rates and turnover and accountants watch the bottom line ($$'s). As the world has become "smaller" and the mining industry has become more globalized, the puzzle is becoming increasingly difficult. Even the most experienced in the crowd of mining profes­sionals are oftentimes surprised by the types of problems that are encountered. Try as we may, we cannot anticipate the complex­ity of dealing with the human side of an operation.

Jan 1, 1998

By David C. Sanders, Rodney H. Sergent, Victor C. Storhok, Batric Pesic

In the past, considerable work has been done on the applica­bility of bromine chemistry in the extractive metallurgy of gold. While the research in this area spanned from the understanding of fundamental dissolution chemistry to the demonstration on a pilot plant scale, no work was done on the fate of discarded leach residues with respect to the stability of accompanied heavy met­als. Because the leach residues were the discharge products of halide/halogen systems, the general perception was that the con­tained heavy metals would be more susceptible to dissolution than in typical sulfate systems, thus causing increased environ­mental problems. A long-term study was performed to obtain the information on the stability of heavy metals contained in the leaching residues after bromination. The study involved the leach residues of three different ores, as well the precipitates prepared from the synthetic solutions (not presented here). The conclusion of this study is that the stability of solid residues produced by bromination leaching was same as the sta­bility of leach residues produced by leaching in the sulfate sys­tems. Also, contrary to the past expectations, the presence of bromide ions in the test solutions (up to 1 g/L NaBr) did not enhance the solubility of heavy metals (Cu, Zn, Pb, As) beyond the solubilities found in the sulfate systems.

Jan 1, 1998

By Barry A. Hillman

The rapid evolution of computer and field sensor technology is now providing the ability to integrate mine and office opera­tions. Digital maps and mine plans as well as CAD and GIS can be transferred to ruggcdized field computers for development of real-time mine surveys and real-time GPS machine navigation and monitoring. Surveyors can insure that their surveys arc accu­rate before returning to the office. Engineers and surveyors are also able to upload field computer-based surveys to mine plan­ning software and directly to mine equipment including shovels, drills, and dozers providing the operator of the equipment with a real-time view of their work space. Production information can be transmitted through dispatch and/or centralized mine servers to update mine plans with mining progress and production data. Static mine models then become a dynamic element of opera­tions, providing greater use of information that emphasizes the spatial aspects of the mine by providing real-time maps, produc­tivity charts, and graphs. This information can be disseminated through various mine communication systems to provide opera­tors and management with real-time feedback as well as daily and weekly reports. Integrated systems now being used in exten­sive trials arc reporting productivity increases of 4 - 7% or more thereby providing rapid payback to the mine.

Jan 1, 1998

By S. Healey, P. Jean, G. Deschenes, M. Fulton

Three years ago, the New Britannia Mine started a project to improve productivity of its cyanidation plant. Results indicated that gold dissolution was strongly influenced by sulphide minerals and that the slower gold dissolution rate had a detrimental effect on overall gold recovery. The leaching strategy had to be modified to address this issue. Changes to the leaching circuit proved to be very successful. The first action was to introduce lead nitrate in the leaching circuit. The strategy of addition of lead nitrate was upgraded in three steps. An on-line free cyanide analyser was installed and the strategy of cyanide addition automated. The enhancement of the leaching kinetics have resulted: an 4% increase of gold recovery, from 87.8% in 1996 to 91.9% in 1999, which represents a reduction of 0.17 git Au in the leach residue; an average of 1330 additional extracted gold ounces per year from 1997 to 1999; a 21 % reduction in the cyanide consumption; the shut down of the cyanide destruction plant; and finally a contribution to the 27% reduction in the overall production cost per tonne of ore.($ 3 per ton). The significant increase of the throughput was instrumental in the reduction of the processing cost. In 1999, the improvement of gold recovery represented an additional gross revenue of $c""l.9 Million. The project is discussed in details in this paper.

Jan 1, 2000

By A. Sfougaris

A study on fauna distribution and abundance is being conducted in the Giona Mountain, in central Greece, area of bauxite mining. The specific aims of the study are: a) to estimate and map the distribution of mammals, and especially of the Balkan chamois, b) to estimate and map the distribution and abundance of breeding birds, c) to count the bird species using the area during spring and autumn migration and winter, d) to update the list of mammal and bird species of the mountain, with emphasis on rare and endangered ones, according to 79/409, 92/43 EU Directives and other relevant conventions, e) to compare the bauxite mining areas and species distribution and assess the possible overlap and compatibility of mining activities - species conservation, f) to assess the possible habitat loss due to planned mining activities. All estimations of mammal species distribution and abundance are being carried out by fieldwork using spotlight during the night along selected routes. Especially for chamois, line transects and vantage points with the aid of telescopes and binoculars are being used. Birds are being counted with the point count method in randomly selected plots distributed in all available habitat types and altitudes. The species distribution and mining areas will appear on thematic maps with the aid of a geographical information system (GIS). Finally, solutions for environmentally compatible mining activity in the area will be proposed.

Jan 1, 2007

By Donald E. Dickie

At Sifto Canada&apos;s Goderich salt mine near Goderich, Ontario, the stress control method of mining was introduced to overcome increasing roof failure problems. After successful testing, the conventional room-and-pillar mining method was converted entirely to the stress control method. This conversion has successfully stabilized the ground, increasing the extracton ratio from 38% to 50%. At the same time, it reduced the ground control and rehabilitation cost by more than 80%. The success of the conversion is due to the quantitative technique of mine analysis that was developed to ensure that the conversion was safe and reliable. A finite element model of the ground was constructed to predict and validate the safety of the stress controlled mine opening. A system of in situ stress-property measurement instruments was developed to obtain input data for the computer model as well as to evaluate its output quantitatively with regard to time and location. History of roof problems Severe roof safety problems have been encountered at Goderich Mine since it opened in 1959. These problems continued into the 1980s. Following excavation, the roof strata started to deteriorate by slabbing. Even after roof rehabilitation, deterioration continued to progressively higher roof elevations, requiring repeated rehabilitation. The operational impact of these roof failures was severe, ranging from a considerable safety hazard to major production interruptions.

Jan 1, 1993

By J. S. Hattrup

INTRODUCTION Tunnel boring machines in non-abrasive competent rock with little or no water have set new performance standards in the driving of tunnels. However, when the machines have hit blocky or running ground, they have encountered difficulties. The success of a tunnelling machine is usually due to a thorough geological investigation which accurately describes the rock conditions, a well designed tunnel support system, and a tunnel boring machine designed to cope with these conditions. In some cases machines have had to be modified in the tunnel after the machine had commenced boring, because geological conditions were not correctly anticipated before tunnelling began. The features described herein are not a panacea for all conditons, and some of them, like an auxiliary thrust system that thrusts off a precast invert segment requires pre-planning of work on the part of the contractor. CUTTERHEAD DESIGN Figure 1 shows typical cutterheads of ten to fifteen years ago. Note the large buckets and large openings between the buckets. These large openings were considered necessary to gain easier access through the cutterhead for cutter changes. The standard cutter in those days was an 11 inch or 12 inch cutter with small bearings, and was generally a delicate tool for the duty it was to perform. These large buckets would clog up if a formation with clay seams was

Jan 1, 1981

By C. Timothy Shaw, Michael Karmis, Hans de Ruiter

The Society of Mining Professors/Societät der Bergbaukunde was established during a meeting hosted by the Montanuniversität, Leoben, Austria, in 1990. Since then, the Society has primarily functioned as a European entity of senior academics in the mining engineering discipline. The Society is considered the natural successor of the historic Societät der Bergbaukunde, formed in the early 18th century and recognized as the world’s first international scientific society. At the 14th Annual General Meeting of the Society, in Milos, Greece, 2003, a decision was made to examine the role of the Society in global minerals education, to reassess its vision and membership guidelines and to develop the future direction of the organization. A special Planning Subcommittee developed a plan of action to allow the Society to transform and position itself as the premier global voice of the academic minerals disciplines and to lead the effort of restructuring minerals education. The new vision calls for reconstituting the Society as a vibrant global society, representing the majority of minerals academics and making a significant contribution to the future of the minerals disciplines. This paper will present the history, vision, goals and action plans of the Society to help ensure that the necessary scientific, technical, academic and professional skills are available for the sustainable supply of minerals to mankind.

Jan 1, 2005