Search Documents

By Neal Rackstraw, Mamo Meaza

Washington Metropolitan Transit Authority Section E8a consists principally of twin tunnels 1,713 meters (5,620 ft) long, excavated to a diameter of 6.35 meters (20.83 ft) using an open face shield, with a primary lining of four unbolted precast concrete segments expanded at the crown, and a full circle unreinforced concrete final lining with a finished tunnel diameter of 5.08 meters (16.67 ft). The tunnels, constructed in Cretaceous age sediments, are mostly in stiff to hard clay except for a few areas along the alignment that contain dense to very dense fine sand in the upper portion of the tunnel that created a mixed face condition. At two locations unexpected heavy water inflows produced very serious problems in both tunnels. Water flows in the interface area were generally more than 378.5 1pm (100 gpm) and reached as high as 2,649.5 1pm (700 gpm) in the mixed face ground. The nature of the tunnel inflows, the consequences, and the corrective measures adopted will be the subject of this paper.

Jan 1, 1991

By Lynn B. Hales, Randy Ynchausti, Jeffrey D. Mckay

Many consider rougher flotation control to be more of an art than a science. Some have even thought it impossible to make process control decisions and changes without human interaction. Controlling flotation bank pulp levels to maintain consistent pulling rates in the face of changing feed slurry flow rates, varying mineral types, and inconsistent reagent additions can be daunting. However, an advanced supervisory control strategy was installed on the plant floor to control an industrial rougher flotation circuit with little or no operator interaction. Plant staff monitored the flotation circuit under supervisory control and reported benefits of up to 4% improvement in copper recovery above that achieved with an older supervisory control strategy. To accomplish this work, a novel use of instrumentation to solve a flotation bank pulp level control problem was employed, a new implementation approach was used to correct some flaws in the older approach, and careful attention was paid to a few key process control principles. This paper discusses important aspects of these activities.

Jan 1, 2000

By William J. Francart, Edward J. Miller

The utilization of computer based monitoring systems for fire detection in underground coal mines has grown significantly in the past seven years. In 1984, an annual MSHA survey identified a total of 38 systems being used in U.S. underground coal mines, while a 1990 survey indicated the number has risen to 112. The applications for mine monitoring have also changed according to the annual surveys. From April 24 to June 21, 1990, investigations were conducted by personnel of the Ventilation Division, Pittsburgh Health Technology Center, in cooperation with Coal Mine Safety and Health, concerning the installation and operation of Atmospheric Monitoring Systems in underground coal mines. These investigations were conducted to gather information concerning the ability of the AMS to detect fires and heatings, false and nuisance alarm frequencies, information related to system maintenance, and information related to employee training on system operations. This paper addresses current applications of the systems, fire and heating identification rates, application of systems in dieselized coal mines, system maintenance, and employee training requirements. While deficiencies were identified in some applications, results of the studies and survey indicate the use of atmospheric monitoring systems can be effective in identifying mine fires and heatings.

Jan 1, 1991

By Richard R. Klimpel

This article introduces the basic definitions and philosophy behind process hazard evaluation procedures and the determination of risk as being a function of accident probabi1ity and accident consequence. The general concepts of good engineering practice and predictive hazard evaluation are discussed. The most commonly employed methods used in the processing industries are reviewed with an eye towards briefly presenting what each method offers as far as information, time and resources required, etc. Some initial references on the actual practical use of each technique in the processing industries are also given.

Jan 1, 1991

By Michel Grenier, Gopal Kunchur, Stephen Hardcastle

This paper presents the findings of a dust study in a typical fluorspar processing plant. The primary purpose of this study was to identify employees and occupational groups exposed to high dust levels and determine compliance with personnel regulations for regular and extended work shifts. The range of airborne concentration of respirable silica and fluoride compounds in specific areas and on personnel was determined. State of the art dust monitoring equipment and tracer gas techniques were used to measure dust concentration, pinpoint dust sources and map major airflow trends in the mill. Results of the survey indicated silica dust concentrations in excess of permissible limits being produced mainly by crushers at the south end of the building. Tracer gas releases and gas chromatographic analysis further showed that prevailing south to north air currents tended to carry and spread dust produced by the crushing operations throughout the process plant. Airborne concentrations of fluoride compounds measured during the study were always well below the prescribed threshold limit value (TLV) for the contaminant. Recommendations, including a mechanical exhaust ventilation system on crushers and transfer points, scheduled preventive maintenance on existing bar sprays and wearing of personal protective equipment were made which significantly improved the work environment. Further testing conducted after Installation of the dust extraction system revealed significant improvements in most areas of the mill.

Jan 1, 1991

By Steven A. Tesdahl

Maintenance means keeping equipment running or restoring it to operating condition. However, the 21st century will usher in a broader need for equipment management, a cradle-to-grave strategy to preserve equipment functions, avoid the consequences of failure and ensure the productive capacity of equipment. Profitable future mining operations will have reduced the 35% of operating costs typically spent on maintenance and the unfavorable impact of downtime that often multiplied these costs by 300%. They will survive those operations that tried to carry outdated "maintenance" thinking beyond the year 2000. These surviving operations will have applied modern management techniques, technology and information to align the efforts of people with the needs of equipment. Future managers will use equipment management as an integral part of an overall production strategy. They will see it as a means of raising productivity, improving performance and minimizing downtime to maximize profitability. This global thinking will characterize all operations planning to survive in the competitive world of mining of the next century.

Jan 1, 1998

By J. A. McKeown, B. M. Sanders, A. Dadgar, R. H. Sergent

This paper describes the leaching of gold with Geobrom® 3400 from a very rich (6.2 kg/tonne) black sand concentrate and its subsequent recovery by ion exchange resins and solvent extraction. The dissolution of gold from black sand ranged from 94 to 96%. Gold loadings and recoveries of nearly 100% were achieved by both ion exchange and solvent extraction methods. The kinetics and equilibrium of loading gold onto ion exchange resins and its elution from the resin were studied. The commercial ion exchange resins PAZ®- 4, DOVEX®- 21K, and Amberlite® XAD- 7, and Great Lakes Chemical experimental GLR-30 were evaluated in this work. Diethylene glycol dibutyl ether was used in all the solvent extraction work for gold recovery from Geobrom leach solution. The consumption of Geobrom was about 130 kg per tonne of the concentrate processed. Therefore, the cost of lixiviant to extract 3.11 x l0-2 kg of gold from the black sand was only about $1.00. Based on the electrochemical regeneration of bromine, the economics of bromine process vs. cyanidation were investigated.

Jan 1, 1990

By T. N. Moore, E. M. De Souza

Because jackleg rock drills are a potential source of hand vibration exposure, they can effectively produce Hand Arm Vibration (HAV) Syndrome in their operators. This will affect operator efficiency and mine productivity. As a result, a significant amount of work has focused on redesigning rock drill handles using new materials to minimize hand-transmitted vibration. In previous work developed by the authors (1991), a detailed study was undertaken to determine the effectiveness of using elastomer covered handles in place of the standard steel design. The results indicated that, for an elastomer-based handle design, the overall acceleration level experienced by the hand can be reduced by as much as a factor of three, relative to the steel handle. It was also shown that this reduction takes place predominantly in the frequency range above 500 Hz. This paper presents an investigation of the long-term effectiveness of an elastomer-cushioned handle under different conditions underground. In this study, sponsored by the Mining Industry Research Organization of Canada (MIROC), a number of cushioned handles were quantitatively and qualitatively tested in five operating mines. The vibration testing program has indicated that the cushioned handle can reduce overall vibration levels by as much as a factor of three. The qualitative assessment program of the cushioned handles by the drill operators has indicated some degree of preference for the cushioned handles over the steel handles, if certain design modifications are performed. This research program indicated that cushioned handles have the potential to become the dominant method with regard to vibration reduction and operator performance.

Jan 1, 1994

By Eduardo Poltronieri Trés, Anderson Denadai Thomazini, Rodrigo Boyer Fernandes, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Maycon Athayde, Rossano Augusto Pilon Nunes

The earliest industrial application of high pressure grinding rolls (HPGR) at comminution was in 1984 in the cement industry. Since then, the equipment has been widely applied in mining activities. Despite the rapid spread across the industry, several challenges are still present in the equipment’s application, especially considering the complex ore breakage behaviour reported for this process. The pellet feed’s HPGR comminution was recognized as fundamental to efficiently increase the particle surface area (e.g., blaine specific area, BSA) at a lower energy and water consumption level (Chapman et al. in J Southern Afr Instit Mining Metall 113:407–413, 2013). The present study considers a novel milling process applying only HPGR as a re-regrind stage after concentration. The amount of successive ground product recirculation into the machine to achieve the required particle size for the pelletizing process was investigated. The study compared the ball wet milling process with the innovative processing technology for hematite–goethite ores. Green pellet balling and induration processes were simulated in bench and pilot scale. The milling results showed a considerably steep increase in BSA after each recirculation step into the HPGR, although compared with the ball-milled product the size fraction <45 μm% increased a modest five percentage points after three recirculation cycles, remaining steady until the last recirculation step. As a result, the green pellet generated presented higher concentration of pellets between 10 and 16 mm (%10-16 mm), with a higher drop number than typically observed when produced with ball-milled feedstock. Consequently, on the induration process, a higher pellet deformation was observed during the pot grate loading. Despite that, the fired pellets still presented an outstanding performance in cold crush strength (CSS) considered suitable to an industrial application.

By John H. N. Yen, James M. Marquardt, Larry H. Heflin

INTRODUCTION On February 17, 1995, WMATA Contractor J.F. Shea holed through the last segment of rock tunnels of the planned 103-Mile Rapid Transit System for the Washington Metropolitan Area Transit Authority. Through the joined efforts and cooperation between the owner and the contractor, the project was completed on time and within budget. The Glenmont extension is on schedule to open in Mid-1998. The complete 103-mile system is scheduled to open in 2001. WMATA’s earlier 19 miles of rock tunnels had been done since 1976 ? By drill and blast with heavy horseshoe steel sets, sets with shotcreting over wire-fabric by TBM and NATM. All rock tunnels were primarily in metamorphic gneiss and schist, part of an east coast lithology that outcrops in a band running from below Richmond, Va. To above New York City. The 5,400 ft. long twin six meter tunnels of the Glenmont line had been earlier de-signed in 1979 by URS of NYC using Jenny Engineering of Pittsburgh, Pa., as a tunnel design specialist sub consultant. Jenny had provided two alternative designs, one conventional drill and blast horseshoe and one for Tunnel Boring Machine. Funding considerations had put the design on the shelf and it was clear that the state of the art had led to improved design methods in the intervening years. Before URS was tasked to update their design in1992, the Authority reviewed its earlier hard-rock experiences in light of the funding mandate to complete each segment on a limited budget and an expedited schedule. Many factors considered and many opinions were in leading to a final decision to drop the earlier designs and redesign for a single designated means of tunneling. That method was the New Austrian Tunneling Method. The NATM had been used earlier on WMATA for both soft-ground and rock tunnels. In the public’s eyes the NATM had become inextricably linked with the use of PVC’s and filter material enveloping or partially enveloping the underground structures to give the holy grail of tunnels, a water-tight structure. Although this link of waterproofing methods with excavation and support methods was essentially severed, a general feeling of their interdependence no doubt helped lead to acceptance of the NATM decision because of the waterproofing design that accompanied it. The Authority decided to drop the TBM and conventional options and provide bid documents for NATM only. URS asked LAW Engineering of Atlanta to provide the NATM design of the tunnels and associated shafts.

Jan 1, 1997

By Joseph A. Dos Santos

Developed in 1983, high angle conveyors - HAC®s are proven versatile systems for elevating materials continuously from a lower to an upper level. Such systems may also be used to lower materials continuously. HAC®s have found commer­cial application in widely varying materials (including coal, refuse, coarse ores [-250 mm], hot clinker, municipal sludge, wood chips, gypsum, slag, excavated earth, various grains and RDF), at widely varying throughput rates from 0.27 to 4250 t/h. The conveying profiles have varied widely and elevating heights range from 3.66 m to 175 m. HAC®s have found application in coal, copper and iron mining, and preparation, in municipal waste treatment, rapid transit projects, pulp and paper mills, cement plants and in gold mining. While noting a wide variety of applications in general, the present writing focuses on Newmont Gold's HAC®, near Carlin, Nevada, which elevates very coarse gold ore to the screening plant. Additionally, upcoming HAC® applications in gold mining are discussed and a proposed multi-flight vertical HAC® system from a deep underground mine is described.

Jan 1, 1996

By Roger Nendick

The recent developments in refractory precious metal ore processing (Bio-oxidation, Autoclaving), and the revitalization of the more traditional roasting processes have attracted great attention in recent years and are indeed the focus of todays symposium. It must always be remembered, however, that the term refractory ore by definition means that the material 'must be capable of being treated at a profit". Given the high cost of the refractory processes, the requirement to be treated at a profit requires very close scrutiny during the evaluation phase of the property development. The M.G.M. film company has the latin motto Ars Gratia Artis meaning Art for Arts Sake. Ingeniatore Gratia Ingeniatoris (a very crude attempt at saying Engineering for Engineerings Sake) should not be the motto for mining companies intent on exploiting refractory gold deposits, but rather the wittily tilted heading for this paper "Take the money and run like a thief". The following hypothetical case studies show that the high technology solution is not always the best financial solution.

Jan 1, 1990

By John T. Crawford

Open pit limit analysis techniques of various types have been utilized for many years to design ultimate pit surfaces. In the last 15 years there have been many advances in the development of sophisticated computer methods to aid this process. The extensive capability of the computer has led to multiple alternative approaches to problem solving. Computerized open pit limit analysis methods can be applied to a broad scope of long-range and intermediate-range mine planning and design questions. A single computer run develops a pit design from a set of data. A set of nonsequential runs is used to evaluate changes in pit slopes, property restraints, and mineral model variables. Ore reserve economic sensitivity and intermediate-range mining plans can be developed using sequential computer runs. Present value methods are incorporated by using iterative sequential techniques. Multiple ore processes, dump leaching credits, and the trade-off between open pit and underground mining can also be handled. Many of the applications described are representative of current practice. The remainder are suggested extensions.

Jan 1, 1979

By T. O. Price

In 1969 Holosonics designed and developed a portable system for conducting acoustical surveys in metal mines, with lead-silver veins as the principal targets. Recently this system has been proven useful in describing rock structures for advance geologic information in civil engineering application and underground construction applications. This paper discusses a case history of acoustical surveying from a series of pilot drill holes in an advancing tunnel. In acoustical surveying a pulsed acoustic signal is used to generate reflected signals from the rock formation. Arrival time, amplitude and phase of the returned signals can be determined. These data became the basis for a signal correlation program designed to relate the signals to their respected pseudo-planar reflecting interfaces. An application of acoustical surveying has recently been conducted in a portion of the excavation for the Washington Metro Area Transit Subway. The data results and conclusions of the program are discussed in the paper. Acoustical surveying was successful in predicting the occurrence of major jointing and foliation plane shearing ahead of the tunnel advancement.

Jan 1, 1974

By Alan Fricker, Bill Owers

Cyprus Gold NZ Ltd will be recovering residual cyanide from their CIT, operation in New Zealand. The process will use air to strip the cyanide from the acidified barren pulp. DSffi. Industrial Development, who were involved in the bench and pilot studies for Cyprus, have extended the concept to pregnant pulp. The stripping of pregnant pulp eliminates the substantial loss of cyanide through carbon catalysed oxidation during the adsorption stage. A 50% increase in cyanide recovery was obtained from an extensive laboratory investigation. The presence of a cyanide recovery circuit enables leaching to be conducted, without detriment, at pHs at least as low as 9, with consequential 50% reductions in the consumption of lime and sulphuric acid. There should be a small reduction in carbon consumption, and a significant improvement in the quality of the final effiuent, at least in terms of cyanide, cyanates, copper, zinc and sulphur. A small but significant increase in gold recovery can be expected too. There is a net economic advantage of NZ$1.20/tonne of ore by stripping pregnant rather than barren pulp.

Jan 1, 1990

By Malcolm Wills

Boddington Gold Mine commenced operation in 1987 with an initial production of 3.0 Mt/y at a grade of 3.5 git. Head grade has reduced over the life of the mine and the major response to the drop in grade has been to increase mining rates and increase plant throughput. A capital expansion was carried out in 1996 increasing the throughput to 6.0 Mt/y and since that date tonnage has been increased without major capital expenditure. BGM's current mill throughput is 8.77 Mt/y ( 1999). In 1999 the combined basement plant and direct leach plant processed 8,770,055 tonnes to produce 233,507 ozs or 7.262882 tonnes of gold at an average head grade of 0.83 git. With grades of 0.83 git, and gold price at record lows, $US251.95loz in August 1999 or $A393.67loz it has been necessary to make and maintain major cost savings to remain profitable. Boddington Gold Mine has achieved this by a number of steps including a productivity study by outside consultants.

Jan 1, 2000

By Michael J. Virnig, Murdoch W. MacKenzie, Michael R. Davis

The objective of this paper is to present preliminary capital and operating cost estimates (±25%) comparing conventional carbon-in-solution (CIS) with resin-in­solution (RIS) using AuRIX® 100 for the recovery of gold and silver from typical heap leach solutions. Preliminary testwork was carried out with AuRIX® 100 using real and synthetic leach solutions to determine the technical viability of the resin for gold/silver recovery and to provide process design parameters for the preliminary RIS circuit. The scope of the resin testwork was sufficient to support the level of accuracy applied in the capital and operating cost estimates. No parallel testwork was carried out with activated carbon. Industry standard design data and operating data from existing CIS operations were used as a basis for the comparison. Both the capital and operating cost comparisons indicate a substantial savings for a RIS circuit using AuRIX® 100 (- 14 to 18% in terms of capital and 25 to 35% in terms of operating costs) over a conventional CIS circuit depending upon solution flows and grade.

Jan 1, 1999

By Lynn E. Bowman

Efficient filtration of fine kaolin particles plays a crucial role in the processing of raw kaolin to a marketable product. Filtration can often be the rate-controlling step of the whole process. Consequently, plant production depends on the rates being achieved in filtration. To alleviate the bottleneck in production, Nalco Chemical Co. initiated a reagent development program to chemically enhance the performance of the filtration units. Filter aids of different classes were assembled and evaluated in bench simulations. These included reagents whose primary mode of functionality were coagulation, flocculation, thickening and combinations of each. This article discusses the development and application of a new reagent that improves the filter production rate with minimal impact on filter cake percent solids. Plant data indicate that this reagent can increase production rates by as much as 35% on clays of varying particle size, as well as clays that are calcined. The reagent&apos;s impact on solids content, re-slurrying characteristics, Brookfield and Hercules viscosity and drying is within the standards set by plants that evaluated and now use this product.

Jan 1, 1993

By Suresh K. Bhatt

Appalachian coalfields have been the predominant source of quality coals since the inception of commercial mining in the United States. In a broad sense, Appalachian coalfields can be considered those east of the Mississippi River, representing about 55% of total US coal production. In this special feature on Appalachia in MINING ENGINEERING, emphasis is given to the four coal-producing states of Pennsylvania, West Virginia, Virginia and (eastern) Kentucky. These four states produce more than 90% of the coal from the total Appalachian region, or about 40% of the total US coal production. Historically, Appalachia has been the principal source of coal for domestic industries and for export. There have been numerous fluctuations in the Appalachian coal industry during the past 20 years. Appalachia was affected by cyclical and structural changes in various industries, particularly the US steel industry, and changing world coal markets. It was also the region of more mine worker labor stoppages than other parts of the country. In general, the factors that affected Appalachian coal production over time are identical to those that determined changes in coal production nationally.

Jan 1, 1995

By Robert F. Jones

INTRODUCTION Upflow Solids Contact Clarification is a process long employed in the treatment of potable water, wastewater and municipal sewage. This process incorporated in a fiberglass conical structure seems to offer an economical solution to problems encountered in reduction of particulates in uranium effuents. CONCEPT OF UPFLOW CLARIFICATION Use of suspended solids contact units date back to the 1930&apos;s. These types of units produced by Infilco and the Permutit Company, among others, were used in the Lime-Soda softening process to precipitate calcium and magnesium salts from hard water. In general, the process operated as follows: (a) Raw water entered a central chamber where it was mixed with chemicals. The chamber had provisions for agitating and circulating the chemicals so that mixing and reaction zones were formed. (b) The water, precipitated chemicals, floc and turbidity flows to a clarification chamber (the Permutit precipitator used a truncated cone). In most cases the influent then passes upward through a blanket of suspended floc and other solids before it leaves the chamber at effluent weirs or launders.

Jan 1, 1984