Search Documents

By P. R. A. Andrews, G. Heinrlch, V. I. Lakshmanan

The paper describes a simplified method to chemically modify the surface of industrial mineral fillers. Four industrial mineral samples were taken from feedstock of commercial fine grinding operations. These samples were ground in bench scale ball mills and in the presence of various organic solvents. The ground products were measured for particle size distribution, surface area, surface chemistry by oil absorption and degree of organicJminera1 bonding. Where appropriate, the ground products were compared to commercially available surface modified, industrial mineral fillers.

Jan 1, 1990

By Edward S. Plotkin, Thames F. Peyton, Gary A. Almeraris

This paper describes high speed tunneling by drilling and blasting in a heavily populated urban area. The project consists primarily of mining 2500 m (8237 ft.) of tunnel through mica schist, excavating three shafts approximately 200 m (650 ft.) each and concreting lining 5300 m (17,400 ft.) of 7.34 m (24 ft.) inside diameter tunnel. The techniques developed and equipment utilized to ensure a high rate of tunneling advance are described. Extensive planning and good communications were especially essential in maintaining production on this project since tunnel mining, tunnel concreting, and shaft excavation all proceeded simultaneously from one common work shaft and a single heading.

Jan 1, 1985

By Joe Maloney, Steve Shadow

Mining conditions at Cyprus Amax's Twentymile Coal Company (TCC) require the use of regenerative conveyors. Regenerative conveyors were first used in the Southwest Mine District and then in the challenging East Mine District. This paper will discuss the development and refinement of the equipment used to brake the regenerative conveyors.

Jan 1, 1998

By S. Formby, J. Avraamides

Transportation of sodium cyanide from factory to minesite often attracts adverse comment from both the community and government agencies. In Western Australia the transportation of 30% w/w aqueous sodium cyanide solution raised fears in the community concerning the safety of such material in the event of spillage. The Chemistry Centre of Western Australia initiated a study of the effects of such a spill, to determine appropriate short and long term response strategies. Factors which were considered included the rate of hydrogen cyanide gas release under various climatic and soil conditions and the effect of alternative treatments in reducing such emissions. The data collected have been used to plan emergency response procedures.

Jan 1, 1989

By Glenn P. Jones

Laterization of syenite and other rocks in north Alabama produced material which was picked up and carried by streams to southeast Alabama. These streams deposited the aluminum rich material in the sinkholes of a karst topography developed on the Clayton Limestone. Measurement of the bearing of the long axis of each deposit in the Screamer area, along with plotting the location of these deposits on a map, indicate a depositional pattern controlled by local fractures or solution zones in the Clayton Limestone. The sinkholes and channels dictated the original structure of the deposits. Additional structure changes have resulted since compaction of the deposits by continued solution of the underlying limestone. The original material in these deposits was enriched by the removal of silica to form bausite and bauxitic kaolin during deposition and compaction. Subsequent ground water action has reintroduced silica into the deposit leaving a core of bauxite.

Jan 1, 1972

By R. D. Hagni, R. T. Brandom

An ore microscopic study of the Boss-Bixby, Missouri, copper-iron deposit has shown that the mineralization formed as a simple sequence of oxides followed by cobaltian sulfides, copper-iron sulfides, and then oxides. The hypogene ore minerals found by this study are magnetite, hematite, ilmenite, rutile, chalcopyrite, bornite, covellite, cobaltian pyrite, carrollite, sphalerite, clausthalite, galena, electrum, scheelite, wolframite, and a Pb-Bi-Se-Te mineral. Textural evidence indicates that some of the early oxides were original constituents of the host syenites and oxidized during cooling. The remainder of the mineralization formed as breccia fillings and replacements. Subsequent partial oxidation has formed martite, covellite, rutile, and anatase.

Jan 1, 1987

By M. J. Klishis

This paper presents the findings of a study on roof bolter's hazard exposure. A "microanalysis" of accident data was combined with ergonomic observations of roof bolter operators to categorize bolting-related injuries, and, from this, a checklist was constructed. Bolting-related problems were identified as situations that could expose bolter operators to hazards. Approaches to avoid these situations were applied at six mining operations to evaluate specific problems in root bolting operations. The research emphasized the importance of analyzing worker behaviors in the context of mining situations and equipment-design problems that lead to human-error accidents.

Jan 1, 1996

By Rilung Xu, Jerry C. Tien, Jian Liu

As underground mines become deeper and ventilation networs more complex, ventilation data becomes more complicated and voluminous, making timely ventilation planning and necessary changes more difficult. Oftentimes, ventilation engineers have to rely on special techques using graphs and schematic maps to carry out necessary ventilation planning [1, 4, 5, 6, 9, 10, 11, 12]. A different graphical method, similar to that reported by Taminago and Isobe [10], has been developed in China [13]. This method uses a two-dimensional diagram drawn from available ventilation survey results. It combines both the customary pressure-quantity diagram and ventilation schematic map, and can greatly expedite the interpretation of survey results, facilitate ventilation system design, short and long-range planning, and emergency planning.

Jan 1, 1993

By W. V. Harper

The travel path of a freed radioactive particle in an aquifer must be estimated from a limited number of available samples. This paper discusses geostatistical methods that minimize the 'uncertainty' associated with the predicted hydrologic surfaces and the predicted travel path. However, any estimation method will produce a single smooth predicted path. This 'sensitivity' will he evaluated using a geostatistical simulation method. The techniques will be illustrated using published data from the Wolfcamp and Pennsylvanian aquifers in the northern Texas Panhandle.

Jan 1, 1990

By R. A. Metz, Isaac Vera, Hans Ruge

The El Soldado copper mineralization occurs as relatively high-grade irregular ore bodies with assay contacts and with frequent inclusions of barren rock. The sampling methods must be timely for production grade control purposes, as well as accurate and inexpensive. Sampling techniques evolved from sampling dump cars at the haulage level to sampling Scooptrams at the loading pockets. These methods were abandoned in favor of sampling production blastholes. Several sampling alternatives are discussed. These involve the selection of optimum volumes and sampling frequencies while taking into consideration geological parameters and statistical analyses of sampling data.

Jan 1, 1992

By David R. Shaddrick

Ore reserves are based on sampling developed by drilling programs. Correct choices concerning the type of drill to be used, depth of drilling, hole orientation and sample spacing are not only critical to the accuracy of the ore reserve but to the cost in time and money of the project. Appropriate interpretation and use of geologic information can significantly enhance the ability to make these decisions effectively. Geologic characteristics of mineralized rock that affect drilling and sample quality include: rock quality, openness, water content, mode of gold occurrence, internal gold distribution and grain of mineralization. Each of these characteristics and sources of data about them are revuewed, then related to the various drill program options. Finally, some procedures for checking the validity and appropriateness of the selected options are reviewed.

Jan 1, 1987

By Birger Schmidt

The design of underground nuclear waste disposal facilities poses new problems related to the requirement of long term safety against radionuclide migration. The degree and effects of rock disturbance caused by construction and by the long term thermal effects from the hot waste must be predicted with confidence. Computer modeling can, to an extent, be verified by accelerated near-surface tests. Credible extrapolation to deep, long-term conditions requires successful near-surface modeling verification, proper characterization of near-surface and deep rocks, and successful determination of in-situ stresses. Excavation induced disturbance may be assessed primarily by empirical evidence.

Jan 1, 1981

By G. W. Rhodes, B. P. Cavan, F. K. Mussger

The New Austrian Tunneling Method (NATM) has been successfully applied to two very different tunneling projects in the U.S.. In the case of Pittsburgh's Mt. Lebanon Tunnels, two original design alternatives were prepared. The NATM alternative incorporating a reinforced shotcrete final lining was successfully bid and constructed. At Washington Metro's (WMATA) Section B-10 Glenmont Route, Wheaton Station and tunnels, a NATM value engineering redesign was prepared for the low bidder. The design incorporating a waterproofing system based on a PVC membrane between the initial and final linings was accepted by WMATA. In both cases, European experience and standards were meshed with U.S. standard practice. Examples of NATM flexibility as an original design and as a value engineering proposal are presented.

Jan 1, 1985

By P. R. McOllough

The Colorado Department of Highways awarded a contract to construct the Second Bore of the Eisenhower Tunnel in August, 1975. The contract was completed June 29, 1979, nine days ahead of schedule, with¬out major claims or delays. The tunneling involved complex construction through difficult ground conditions. The contract, plans and specifications were specifically planned to more equitably share the risks involved and to minimize adversary relationships. The Department produced a detailed tunnel design and maintained responsibility for the design. The contract employed some new provisions; e.g., a review board for settlement of claims and disputes; escrow documents (contractor's bid documents) to determine the contractor's basis of bid when determining adjustments. The tunnel contract, plans and administrative efforts employed by the owner and contractor were very successful in this project.

Jan 1, 1981

By Les T. Zoschke

Over ten years ago, Modular began development and implementation of its DISPATCH System for haulage optimization in open pit mines and now has over two dozen systems in operation worldwide. The so-called 'top down' approach used in system design and implementation was deliberate. This foresight now allows addition of features which would otherwise prove infeasible - without complete system redesign. Until recently, truck and shovel operator input provided timing data needed for optimal allocation. Now, addition of a high-speed, general purpose token ring loop controller and infrared (IR) transponders to each piece of mining equipment automates these important functions. Here, we discuss new devices, systems, and subsystems comprising mining's future.

Jan 1, 1992

By A. Unal, R. L. Grayson

The use of radio frequency identification (RFID) technology to solve informational needs in isolated and restricted underground mining environments are reviewed, and the specifications of some of the past and currently available systems are presented. The advantages and disadvantages of using various frequencies, system configurations and specific components, including their construction standards and capability, are also discussed. The remaining challenges to the more widespread use of RFID systems for personnel and vehicle tracking are identified, and recommendations concerning the operating environment capabilities are detailed. Finally, the ultimate requirements for maintaining system integrity during and following a coal mine emergency are discussed.

Jan 1, 1999

By A. D. Trujillo, R. D. Wunder

The Chino Mines Co., a Kennecott- Mitsubishi partnership, located in Hurley, NM, recently completed a $405 million modernization of its mine, concentrator, and smelter facilities. The mine/concentrator modernization commenced in 1980, and the smelter modernization began during 1982. Modernization of the mine and concentrator facilities involved increasing the mining rate from 98 kt/d (108,000 stpd) to 152.2 kt/d (167,800 stpd). Ore mining was designed to increase production from 20.2 kt/d (22,300 stpd) to 34 kt/d (37,500 stpd). A new concentrator was con- structed near the mine using semiautogenous grinding. The new smelter uses the INCO flash smelting process, increasing capacity by 40.8 kt/a (45,000 stpy) to 99.8 kt/a (110,000 stpy) of saleable copper.

Jan 1, 1988

By Eduard Hamm

The main reasons for the development of higher heat levels in German coal mines are the increasing depth of working with the con- sequent higher rock temperatures, increased use of electrical equipment, and increasing coal output due to concentration and mechanisation of workings. In place of the normal decentralised underground cooling plants, schemes and pilot plants have been developed to produce the required cooling capacities in central air cooling units, which then supply the cold air to the underground working points where needed.

Jan 1, 1980

By David S. Yantek, Paul Jurovcik, Eric R. Bauer

Workers in coal preparation plants, where vibrating screens are significant noise sources, are often exposed to sound levels exceeding 90 dB(A). The National Institute for Occupational Safety and Health, a major coal company, and a vibrating screen manufacturer conducted a cooperative study of vibrating screen noise. Rubber isolators reduced sound levels by 1 dB. Urethane screen panels did not reduce sound levels in this case. Drive noise was determined to be the dominant noise source on the screen. Damped side plates reduced vibration levels on the screen sides by 1 to 7 dB(A). Detailed results of the study are presented.

Jan 1, 2005

By J. M. Mutmansky

The objective of this study was to produce coal dusts for laboratory research that are similar to mine airborne dusts in chemical, mineral, and physical characteristics. In this investigation, dusts produced in laboratory comminution equipment were compared with continuous-miner-generated dust for similarity in physical characteristics. Mining-generated dust (MGD) and bulk coal samples were first collected from an underground mining operation. The bulk samples were then processed in the laboratory for size reduction in various comminution devices. These laboratory-generated dust (LGD) samples were subjected to size and microscopic analyses. Physical properties of the dust particles were studied on a scanning electron microscope (SEM). A numerical shape coordinate system (SCS) was also developed and applied to 300 particles from each sample. Statistical analysis was then performed on the collected data and characteristics of the MGD and LGD samples were compared.

Jan 1, 1995