Search Documents

By G. M. Riddle

As an important part of the concept validation phase of the MX Advanced ICBM development program, Air Force System Command's Intercontinental Ballistic Missiles (ICBM) Program Office developed and demonstrated large trenching and cast-in-place equipment for placing many miles of buried concrete tunnel rapidly and economically. A tunnel or "buried trench" containing a mobile ICBM is one of the candidate basing models for MX. Upon remote command, the cannister housing the missile would break out of its concrete tunnel and earth overburden by erecting itself to a suitable angle and then launching the missile. The ICBM Program Office developed two each trenchers, cast-in-place machines, and breakout mechanisms, as well as a mobile concrete truck unloader. The machines were demonstrated in varying soil conditions in the southwest US. The breakout mechanisms were demonstrated nearby as well. This chapter describes the development program, the machines, and the demonstrations. No manuscript received

Jan 1, 1979

By John E. Litz, Charles W. Kenney, Wayne Carter

Refractory gold ore pretreatment processes continue to receive much attention. This paper compares the relative economics of treating ores by oxygen pressure oxidation, roasting and bacterial oxidation with or without preconcentration by froth flotation. Capital and operating cost estimates for each method of pretreatment were prepared and these estimated costs and ore sulfide grades then are used to compare the process economics. The study indicates that the most significant item affecting the economics is the amenability of the ore to flotation. The cost benefits of flotation are $10-13 per tonne ore processed (2%-4% s=, 10:1 ratio of concentration). In most cases bacterial oxidation has the lowest overall cost, especially if less than complete oxidation of the sulfides will give acceptable recovery, however bacterial oxidation has yet to be practiced on a large scale. In all situations pressure oxidation shows the highest cost. However, the cost differences between the treatments are small, less than $7 per tonne.

Jan 1, 1990

By A. J. Douchane, J. M. Shirley

The high grade gold and silver Ken Snyder Mine is located in north-central Nevada, in Elko County, adjacent to the town of Midas, approximately 240 miles to the east­northeast of Reno and approximately 60 miles to the northeast of the town of Winnemucca. The Midas Joint Venture (MJV), an equal partnership between Franco-Nevada Mining Corporation, Inc. and Euro­Nevada Mining Corporation, Inc. with Franco-Nevada Mining Corporation, Inc. being the joint venture manager, owns the mine. In May 1997, Kilborn Denver, now SNC-Lavalin America, completed a bankable feasibility study and proceeded with detailed design, procurement and construction management. In mid December 1998, MJV not only poured their first gold several months ahead of schedule, but were already operating at full production. In addition, the construction of this US $84 million mine, mill and related facilities were completed on budget. Operating cash costs are US $78/oz. This paper describes how this was accomplished.

Jan 1, 1999

By Gregory A. Vaka

Robins Engineers & Constructors, Inc. as the exclusive U.S. licensee introduced the PIPE CONVEYOR to the North American marketplace early in 1984. The sale of the first PIPE CONVEYOR in 1985 was a difficult task since the conventional troughed belt conveyor was the accepted and the most widely used means of continuous transportation of bulk materials handling in the world. Initially our clients viewed the PIPE CONVEYOR as a departure from the normal and accepted form of material handling. Since then, the parent company of Robins Engineers merged with Krupp of Germany to form KRUPP ROBINS, INC. in the United States. To date there are over 462 PIPE CONVEYORS operating worldwide with the majority of the long overland systems designed and installed by Krupp Robins, Inc. The PIPE CONVEYOR is now becoming the norm, viewed by those who are familiar with its capabilities as the preferred method of transportation for all bulk solids.

Jan 1, 1997

By M. Misra, J. Nanor

The removal and stability of arsenic over a wide pH range (3.0-10.0) from synthetic solutions and industrial waste effluents (including mining waste tailing slurry) can be accomplished with addition of impure lanthanum chloride alone or in conjunction with ferric sulfate. The long term stability of these correspond­ing precipitated compounds is critical from the disposal stand­point. In this paper test results of this new process for arsenic removal and stabilization from the above mentioned systems are presented. Also, precipitated arsenic compounds (lanthanum arsenate, lanthanum-ferric arsenate, ferric-lanthanum arsenate and ferric arsenate) from synthetic solutions have been charac­terized. The characterization technique used was XRD. XRD patterns which shows that the lanthanum arsenate and lan­thanum-ferric arsenate formed in acidic and alkaline pH at room temperature are crystalline. On the contrary, ferric arsenate and ferric-lanthanum arsenate compounds formed under the same conditions as lanthanum arsenate were amorphous.

Jan 1, 1998

By Luis Tondo, Gary Johnson, Steve Morell

High pressure grinding rolls have been demonstrated by numerous researchers, and at a number of commercial installa­tions to be power efficient comminution devices. They have become almost "standard equipment" in the grinding of cement clinker. However, the technology has been relatively slow to catch on in the mineral processing industry. Part of this may be due to the fact that this relatively expensive machine has not been incorporated into the plant flowsheet so as to fully exploit its power efficiency, and therefore realise the maximum economic benefit. This paper describes the results of a pilot scale test program designed to evaluate the performance of the device with the aim of developing a circuit configuration that better exploits the inherent power efficiency of the machine. The results of the test program clearly show that power savings of about 50% over conventional technology are achievable when the machine is made to produce the final product grind size.

Jan 1, 1995

By S. Stewart

The topic of sustainability in the mining and minerals industries focusing on economic development, ecological integrity and responsible stewardship of the environment together with community well being are vital issues for our industries at a crucial time in our history. Many of the priorities of the Greek Presidency of the European Community ? Sharing the Future in a Community of Values ? encourage our industry to continue to innovate and develop many of the environmental and social initiatives already underway. Sustainable development is here to stay and has been placed strategically at the heart of all European public policy. The future of the minerals industry here in Europe as well as elsewhere depends on how well professional mining people, both as individuals and through their associations and others, have to present their case for a sustainable mining and minerals industry to a critical world. And, Greece with its strong and expanding mining, minerals and metals base has more to win or lose from this endeavor than many others.

Jan 1, 2003

By S. J. Porter, M. T. McRae

The new tunnel at Genting Sempah is part of a privately funded infrastructure projectthat involves duplicating the existing highway extending from the Gombok Toll Plaza near Kuala Lumpur to Karak, in Malaysia. The 60 km long tollway includes an 800 m long, two-lane highway tunnel with excavated dimensions of 10.5 m wide by 8 m high. The majority of the tunnel extends through slightly to moderately weathered, moderately to highly jointed quartz porphyry. Excavation of the tunnel was performed using drill and blast methods and the primary tunnel support consists of rock dowels and shotcrete except for short sections adjacent to the portals where steel sets were utilized. A portion of the tunnel encountered sheared and altered material that was successfully supported using rock dowels and shotcrete. The final lining for the tunnel consists of mesh and fiber reinforced shotcrete. The flexible nature of the primary support and shotcrete final lining resulted in considerable cost savings and expedient construction methods.

Jan 1, 1997

By David R. Wayman

This paper summarizes environmental compliance and related issues associated with underground construction and tunneling operations, whether new work or rehabilitation. Underground construction and tunneling operations have (in most cases) both an underground and surface component. Since many of the major tunneling projects occur in urban areas, often is areas inhabited for several decades or centuries, environmental problems may already exist in a project area, though that may not yet have been formally recognized. Large projects often attract more than their fair share of regulator attention. This paper addresses the issues with the greatest potential to be encountered by underground constructors, with the emphasis on minimizing contractor liabilities, both in the short- and long-term. Minimizing contractor liability begins with understanding bid documents, contract provisions and necessary means of protection, and carries through project execution by responsible control of hazardous materials, avoidance of media contamination, proper waste disposition, as well as compliance with other environmental requirements.

Jan 1, 1999

By Kambhampati C. Rao, Cecil Lue-Hing, Nabih P. Kelada, William B. Willborn

improvements in the analytical techniques for cyanide speciation can furnish useful information about the behavior of the different cyanide species in the receiving environment. This could be of help to the environmentally concerned public and the regulatory agencies in the assessment of cyanide limits for effluents, stream quality, and land disposal of cyanide bearing wastes. In addition the ability to distinguish the free cyanide and the weakly bound cyanide from the strong ULTRAVIOLET IRRADIATION UNIT (LAMP, COIU3' HOUSING) FIGURE 1 complexes, as well as transformation to thiocyanate is also needed by different industries, such as mining and metal finishing, etc., to evaluate the efficiency of several processes. Cyanide has been used for the recovery of gold since the late 19th century. Although cyanide leach solutions are mostly recovered and used again, a large quantity of cyanide bearing wastewater becomes unfit for use and has to be treated before it can be released into natural waterways.

Jan 1, 1992

By Brendan Parker, Joseph Skrypniuk

Boddington Gold Mine1 (BGM) commenced production in 1987 and is currently ranked as the second largest gold producer in Australia. In a strategy to improve plant efficiency, constraints to plant performance were identified and prioritised with a view to maximising benefit for minimal expenditure. After identifying that leach kinetics and circuit residence time were major constraints, the introduction of oxygen was identified as having the greatest potential for the delivery of sig­nificant cost benefits. The application of oxygen, initially by conventional tech­niques, and subsequently by installation of Atomaer's Filblast gas shear reactor, improved gold recovery, reduced the resi­dence time constraint and enabled higher mill throughput to be achieved. Additional benefits included operation at lower pulp densities and a reduction in reagent usage. A significant reduc­tion in unit operating cost resulted from these benefits. This paper quantifies the above benefits in a format accept­able to both metallurgists and accountants by integrating the findings in a techno-economic perspective.

Jan 1, 1996

By Michael G. Strominger, Anthony E. Gross

The development of precious metals ore agglomeration with a cement binder, by the U.S. Bureau of Mines, has allowed the economical heap leaching of low grade gold ores (<0,05 oz/ton) over the last decade, Even with the Bureau of Mines technology, numerous operations continue to experience channeling and blinding problems. A research project was undertaken at Nalco Chemical to address situations where improved agglomeration is needed, By increasing the incorporation of fines into the agglomerates,the segregation of ore by size which occurs from handling will be reduced and channeling minimized. A stronger agglomerate will reduce fines migration during leaching and prevent blinding of the heap, Both of these changes will give an even flow of barren solution throughout the heap and give solution contact with all of the ore. This paper presents the development of polymeric agglomeration aid, Nalco 9760 which has given a higher rate of and a higher total gold recovery in plant evaluations.

Jan 1, 1990

By Harry Holle, Gary Johnson

A plant trial was conducted at the Paddy's Flat plant of Dominion Mining Limited with the aim of comparing the ef evenness of oxygen and hydrogen peroxide as leaching oxidants. The Paddy's Flat plant is designed such that the leach train can be divided into two parallel streams, allowing the same or lurry to be eated in two identical trains. By effectively ehminatmg the influence of the ore variations on the results subtle differences in the performance of the two reagents hav been identified. . . The results of the plant trial indicate that the two reagents act m different ways, and that each may be more suitable than the other _for _the treatment of certain types of ore. In some cases a co bmation of the two reagents may be the most cost effective option. . or t e same chemical conditions in the leach pulp, including dissolved oxygen levels , the reagents achieve different gold leaching rates, and in some cases different ultimate leach extraction.

Jan 1, 1992

By S. Vukcevic, R. Winby, P. C. Miller

There is considerable interest in the bioleaching of chalcopyrite concentrate for the production of copper. The residue of bioleached chalcopyrite often contains gold that needs to be recovered. Despite the high efficiency of copper bioleaching, the residue may contain appreciable quantities of copper, and the difficulties of cyanidation of gold from copper bearing materials are well recognised. This paper reports the results of using different methods to recover the gold values from bioleached chalcopyrite concentrate. In particular, the behaviour of cyanide and cyanide in the presence of ammonium ions as gold lixiviants were studied. The ammonia was employed to reduce the impact of the copper on cyanide consumption. Thiosulphate as a gold lixiviant was also employed with the aim of achieveing rapid leaching rates and to reduce the impact of residual sulphur species on lixiviant consumption. Bromine solution was used to research acidic gold leaching. The paper describes the advantages and disadvantages of using different reagents with respect to reagent consumption, selectivity and kinetic efficiency.

Jan 1, 1997

By Frigyes Egerer, Pál Bárczy

Introduction Charles III, Holy Roman Emperor and King of the Austro-Hungarian Monarchy, established one of the first mining schools in Europe on June 22, 1735, in Selmecbanya (Schemnitz in German and Banska Stiavmica in Slovakian). The old city, built around the ancient gold mines, is shown in a contemporary engraving in Fig. 1. Charles&apos; historical decree consisted of 13 chapters and included: the deed of foundation, the definition of grants, instruction for educational policy and curriculum, disciplinary rules, and the appointment of personnel. The first professor of the school, Samuel Mikoviny, gave his first lecture the same year, in December 1735. The 250th anniversary of the establishment of the School of Mines was celebrated Sept. 2-4, 1985, in Miskolc. It was attended by representatives of other Hungarian and of several foreign technical universities. A silver medallion (Fig. 2) was issued to commemorate the occasion and a series of lectures

Jan 6, 1986

By Bernie W. Martin, Duncan MacLennan

Building a new tunnel to accommodate CN North America&apos;s needs for double stacked container traffic for the next 100 years presented new and unprecedented challenges. Innovative approaches to contracting, especially the Negotiated Compressed Process (NCP), TBM design, project management, and the regulatory and approval process, were all required to deliver a new tunnel to meet the needs of CN North America within the approved completion schedule of 39 months compared to a traditional approach of 45 to 48 months. The NCP resulted in trimming 6 to 9 months from the project schedule, at a great saving of direct and indirect costs. The Negotiated Compressed Process is an innovative formalized approach to risk sharing for complex infrastructure projects. Ads were placed in the international trade journals and a short list of "approved" contractors and suppliers was developed. The approval process for this international project involved contacts with over two hundred agencies, departments and interested stakeholders.

Jan 1, 1995

By Douglas C. Shumway

Mining in Cushenbury Canyon began in 1860 when John Cushenbury left his Holcomb Valley gold prospect and discovered a silver vein in the limestones of the present day Cushenbury Mine. Cushenbury Canyon is located along the western boundary of the Mojave Desert in southern California and on the north slope of the San Bernardino Mountains. The Holcomb Valley, immediately south of Cushenbury Canyon, was the most prolific gold producer in southern California. Gold mining dominated the area until World War II. Interest then turned to the Lucerne Valley limestone deposits when Kaiser Steel built a plant in Fontana, CA. The steel making process required large amounts of metallurgical grade limestone. In 1956, Kaiser Cement constructed a cement plant and limestone mine in Cushenbury Canyon. In 1982, Kaiser modernized the facility to a four-stage, preheater-precalciner system. Mitsubishi Cement Corp. purchased the property in April 1988. The company further modified the facility to create the most efficient and modem cement plant in the US.

Jan 1, 1992

By E. R. Slatick

The northern and central Appalachian coal basin in the eastern United States has been the source of about two-thirds of the nation&apos;s coal output during the 20th century. This region includes parts of Pennsylvania, Ohio, Maryland, West Virginia, Virginia and eastern Kentucky. It covers about 130,000 km2 (50,000 sq miles) of the Appalachian coal basin and ranks as one of the world&apos;s most important coal production regions (Fig. 1). The coal industry&apos;s heyday in northern and central Appalachia has passed. This was due to competition from other fuels and low-sulfur coal produced in the West and because of the declining use of coking coal for steelmaking. Nevertheless, the region still plays a vital role in US coal production. It currently produces about 40% by weight of the nation&apos;s coal (its share is about one-half when measured by the energy content of the coal), contributes substantially to electricity generation and serves as the mainstay of US coal exports.

Jan 1, 1995

By Nancy Bingham

The mining industry’s image is molded by what the public knows, or thinks it knows about mining. As Caterpillar prepared for the production of its educational video, Common Ground, the public’s perceptions about mining needed to be established. Before we could educate people about mining, we had to find out what they already thought. As those perceptions were analyzed, we were able to narrow the video’s focus to relevant, realistic approaches. We found out what people did not know about mining. And, most importantly, facts they should know were singled out - facts that could create more favorable attitudes. This research was instrumental in the final direction of the Common Ground project. What the public believes As these perceptions about mining were researched, it was found that the beliefs of the general public are dominated by four concepts. Quotations from interviewees are included with the discussion of each of these concepts. Figure 1 shows an overview of people’s beliefs before education.

Jan 1, 1994

By J. R. Weber, R. D. Haddenham, J. H. Bailey

Introduction The Vernal Phosphate Operation is located in northeastern Utah, about 18 km (11 miles) north of Vernal, about 280 km (175 miles) east of Salt Lake City, UT. The plant began initial operations in 1961 under the name of the San Francisco Chemical Co. In 1981, Chevron purchased the operation from Stauffer Chemical Co. In 1982, plant capacity was doubled to about 72.6 kt/a (800,000 stpy) of phosphate concentrate. From 1984 to May 1986, another expansion increased the capacity to 1.2 Mt/a (1.3 million stpy) of concentrate. It also incorporated a number of equipment and process changes designed to increase the overall plant phosphate recovery. A 150-km (94-mile) slurry pipeline, the world&apos;s longest phosphate pipeline, was also constructed from the Vernal plant to a new Chevron Chemical and Fertilizer plant near Rock Springs, WY. Over the past five years, plant expansions and the pipeline construction have been accomplished without missing a single concentrate shipment.

Jan 1, 1987