Search Documents

By Gordon Hubbard, John D'Acierno

The Randgold Resources Ltd. mine operation in Syama Mali performs whole ore roasting followed by CIL gold recovery to produce gold. The roaster has operated continuously since the plant was first commissioned in 1994. The roaster design throughput is 216 tons per hour (5,184 TPD). Roasting provides for the oxidation of the· refractory components, organic carbon and sulfides. The energy balance for the system requires auxiliary fuel oil to be burned in the Circulating Fluid Bed (CFB) reactor. Energy from the 1200-1350 degree F roasted product stream is recovered and recycled back into the CFB using two fluidized bed coolers; one to directly heat the secondary air and the other to indirectly heat the primary fluidizing air. The basis of the design for the roaster was an extensive pilot plant test program, the results of which were scaled up to the full scale plant design. Due to variation in the feed at the mine a number of roaster modifications were necessary following the initial plant start up. During 1998 ore flotation capability was added to reduce the operating cost for the roaster and increase plant throughput.

Jan 1, 1999

By David Marsh, Mark W. Johns

Carbon-in-pulp (CIP) is a preferred method of gold recovery from cyanided pulp. However, the resin-in-pulp (RIP) process is considered to have several advantages for the recovery of gold. Mintek therefore undertook a research programme to develop a commercially-viable RIP process. The MINRIP RIP process and a novel gold­selective strong-base resin, Minix, were developed. The process has been successfully demonstrated at a scale of 100 000 t/month. Continuous countercurrent tests using synthetic solutions indicate that the relative performance of an adsorbent depends on the composition of the solution. Minix resin yielded a higher gold loading than that of carbon, while maintaining an acceptable barren value. Batch tests on a number of gold-bearing materials indicated that Minix has potentially a higher capacity than carbon, and loads gold faster than carbon. An economic appraisal that consolidated the countercurrent results and the economic study indicated that the capital and operating costs of the Minrip process are considerably lower than those of CIP. The amount of the cost advantage depends on the gold content of the feed and the throughput.

Jan 1, 1993

By David J. Gurtler

In early 1988, Chino Mines Co. began using a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction electrowinning plant feed, and non-ore material, to determine its disposition. Results thus far indicate a significant increase in financial returns on material mined compared with the copper cutoff grade previously in use. Chino Mines is a partnership between Phelps Dodge Corp. (two-thirds ownership) and Mitsubishi Corp. (one-third ownership). The company produces copper and byproduct metals from the historic Santa Rita del Cobre mining district in southwestern New Mexico. The history of copper production in the district began with the use of surface native copper by native Americans before 1800. Spanish soldiers from Mexico later became aware of this district and mining began in 1801. The district was worked intermittently until 1909 when the Chino Copper Co. was formed, with Daniel C. Jackling as vice president and managing director. Concentrator operations were started in 1911. Kennecott purchased the company in 1933 and built a smelter in 1939. Chino Mines Co. was formed in 1980 when Mitsubishi purchased one-third of Kennecott's holding at the property.

Jan 1, 1990

By Richard Lovat

INTRODUCTION Soft ground tunnels may be above the ground water table or they may be subaqueous. The ground may be clays, silts, sands, gravels, glacial deposits, boulder tills, and any of these in any combination. Because of the relatively low strength and deformability of soils, difficulties often arise in soft ground tunnelling. These soil characteristics and resultant tunnelling difficulties, have had a direct influence on the development of "Lovat" Tunnel Boring Machines. We have been required to recognize and adapt to unusual ground conditions and to follow through with design, fabrication, and field maintenance to ensure dependable, trouble-free operation. The basic "Lovat" machine is a fully shielded, wheel-type with the cuttinghead driven by a monorace type bearing with gear drive incorporated in the bearing. Mechanical innovations have been added to the basic machine which complement the resources of manpower, equipment, and materials available to the contractor for a specific operation. FULL FACE SUPPORT The installation of hydraulically operated closure doors or flood control doors, at the cuttinghead, is one of the early "Lovat" technical innovations. Flood control doors provide full face support in running or flowing ground. In water bearing sands and silts the excavated material can

Jan 1, 1981

By Kenneth R. Miller

ThunderBasin Coal Co. has two mines located in the southern portion of Wyoming's Powder River Basin - the Black Thunder Mine and the Coal Creek Mine. Both are located 60 to 90 kin (37 to 55 miles) southeast of Gillette. The mines are principally located on federal coal leases acquired in the late-1960s. Development plans for the Black Thunder Mine focused on dragline stripping. Environmental considerations, however, made truck-shovel stripping the method of choice when the mine opened in 1976. In 1981, the Coal Creek Mine opened as the first dragline mine in the Gillette area of the Powder River Basin. The regional terrain is flat-lyimg with occasional clinker-capped hills. The mines are located on the Wasatch and Fort Union Formation contact. The coals are Paleocene in age. The deposits are structurally simple, dipping gently to the west. The seams are thick and are classified as sub-bituminous-C. The Black Thunder Mine, with its 21-m (70-ft) 'hick seam, is strategically located in the center of the highest heat value mining area of the southern Powder River Basin.

Jan 1, 1993

By G. E. McKelvey

A group of gold deposits in southeastern Ecuador, near the town of Zamora, have become the focus of intensive mining activity, due to their extremely high gold grade (unconfirmed reports of about 50 g/t or 1.4 oz per st, or more). The deposits at Nambija and other prospects in the district are hosted by a sequence of sedimentary and volcanic rocks that are present within a large xenolith orpendant within alkalic phases of the Jurassic Zamora Batholith. The xenolith, unknown in size, is composed of various island arc lithologies (limestones, shales, sandstones, tuffs and flows). All have been altered to some degree by skarn-hornfelde alteration assemblages. Mineralized areas appear to be localized within a linear zone containing tectonic and intrusion breccias that cross-cut a complex calcic skarn assemblage developed within the xenolith. Although the nature of the host rocks appears to have exerted some control on mineralization, the high-grade ore is concentrated along north-northeast trending breccias, faults and dikes that crosscut the flat-lying stratigraphy and skarn alteration as suggested by the strong linear trend of workings in the district.

Jan 1, 1991

By Stuart Hammer

The mining industry has seen a flurry of merger and acquisition activity of late. Rising metal prices, increased spending on infrastructure in developing nations and the growing demand for companies to diversify have helped fuel M&A activity in this industry. Many analysts believe that the robust M&A activity will continue, particularly if the demand for mineral resources in India and China remains strong. Because prospective purchasers need to evaluate the various risks confronting target companies, acquiring mining companies requires a considerable amount of due diligence. Of these risks, environmental risk is critical and warrants significant analysis. The failure to properly assess environmental risks associated with remediation, reclamation, compliance or litigation can undermine the transaction. Such assessment is a difficult endeavor, however, due to several challenges that companies face when assessing environmental risks. To make matters more complicated, despite these challenges, many sellers ask buyers to assume all environmental risks with limited post-closing indemnification rights. This article addresses the most significant issues that commonly arise when conducting environmental due diligence and allocating environmental risk in connection with M&A transactions in the mining industry.

Jan 1, 2008

By E. J. McGuire, E. W. Brickle

INTRODUCTION Several recent technological improvements - largely by the convey-or industry - have increased the importance of inclined shaft construction for developing mines where ore deposits are relatively shallow. With these newer systems, long conveyor haulages are economically feasible, allowing mine owners to justify the expense of the inclined shaft or slope. What this actually means is that they can now take advantage of the versatility this construction offers. For example, haulage capacity can be changed by conveyor additions or replacements; equipment can be trammed to and from the surface quickly without costly breakdown and re-assembly; and a walkway is available for workers in the event of an emergency. Now, another innovation may accelerate this type of construction, the use of tunnel boring machines or "Mechanical Moles" to dig the slopes. While conventional. drill and blast methods have been used previously to build inclined shafts, the tunnel boring machine technique offers greater production rates, higher safety and a better, much cleaner bore. McGuire Shaft & Tunnel Corporation of Ft. Smith, Arkansas recently started such a slope project - the first ever bid by a contractor based on the use of a "Mechanical Mole".

Jan 1, 1997

By Russell K. McFarland, Eugene L. Foster

INTRODUCTION The U. S. Department of Transportation has underway an important new program which will have a major impact on rapid excavation technology. The Transportation Tunneling Program, as it is called, is a coordinated, multi-modal research and development effort. Its goals, if realized, will significantly improve our ability to build the underground structures needed for transportation. This, in turn, will improve transport efficiency, environmental impact, and the energy consumption associated with the movement of people and goods. Tunneling technology research and development had its beginning at the Department of Transportation in the Office of High Speed Ground Transportation (OHSGT). The OHSGT developed and implemented a program in 1965 to provide the technology for underground construction needed to support future high speed ground transportation. In 1967, when the OHSGT was transferred from the Department of Commerce to the Federal Railroad Administration (FRA), the program accompanied that office. The thrust of the FRA program has been cost reduction through the development of new materials, innovative designs, and better construction methods. During the late 1960's and early 1970's, other developments were underway which would influence the future of tunneling research at the Department of Transportation. An ad hoc

Jan 1, 1974

By Gerald G. Griswold, James O. Greenslade, Cherie Tilley, Richard Reseigh

INTRODUCTION The Harrison Western Corporation, a leading Denver based mine contracting and engineering concern, is presently engaged in sinking two 1,006 m (3,300 ft) shafts for the Phillips Uranium Corporation at their Nose Rock Project, approximately 13 miles northeast of the small community of Crownpoint in McKinley County, New Mexico. The Nose Rock Project is the first attempt by the Phillips Uranium Corporation to tap the deep uranium reserves in what has become known as the Grants Mineral Belt. (See Figure 1) Project Description Phillips Uranium Corporation's plan for the large 2700 metric ton per day (2950 tons/day) mining facility calls for a series of deep access and ventilation shafts ranging from 4.27 m (14 ft) to 5.49 m (18 ft) in diameter to approximate depths of 1,006 m (3,300 ft). The initial pair of shafts consists of one production shaft and one ventilation shaft separated by a distance of 91 m (300 ft). The interbedded layers of sedimentary sandstones and shales to be penetrated by the shafts contain several major water producing aquifers, the deepest being the mineralized zone called the Westwater Canyon Member of the Morrison Formation.

Jan 1, 1981

By E. Topuz

Productivity is the most important determinant in the economics of underground coal mining operations. Lower labor productivity increases labor requirements per ton. This, in turn, increases the unit cost of production. Intensive labor requirements may also affect miner injuries and fatalities by increasing man-hours of exposure necessary to produce a given amount of coal.

Jan 1, 1988

By Hisakazu Matsushita, Yoshio Yamaguchi

INTRODUCTION Shinkansen, operating 1,176km between Tokyo and Hakata, transports 340,000 passengers a day. Presently, the 466km Tohoku Shinkansen linking Tokyo and Morioka and the 270km Jyoetsu Shinkansen linking Omiya and Niigata are under construction. It is progressing smoothly and 95% of the civil and architectural construction has already been completed.

Jan 1, 1981

By J. J. Moore, I. Iwasaki, L. A. Lindeke

Correlation of scale-up from small-scale batch laboratory mills to large-diameter industrial mills was established by performing two series of laboratory and pilot plant grinding tests using a magnetic taconite ore and a siliceous sulfide ore. In one series, controlled batch grinding tests in 203-, 508-, and 914-mm (8-, 20-, and 36-in.) diameter mills were carried out followed by a second series involving continuous grinding tests using 305-mm (12-in.) and then 1067-mm (42-in.) diameter pilot plant ball mills in open circuits. The effects of ball diameter on wear and of mill diameter on grinding power and ball wear are illustrated.

Jan 1, 1988

By L. Borsch

Geochemical laboratories are commonly criticized by geologists about poor analytical reproducibility and erratic anomaly patterns, especially when gold and trace metals from resistant minerals are reported. Geochemical analysis in mineral exploration is a compromise between high productivity on the one hand, imposed by large numbers of samples, and analytical precision and accuracy on the other. However, the physical properties of resistant minerals, such as cassiterite, gold, beryl, chromite, zircon and others, interfere with both of these requirements. Therefore, the degree of sample homogeneity that can reasonably be achieved in sampling and sample preparation must be considered. Subsequently, the understanding of its effects on analytical data quality and the consequences on data interpretation will provide a basis for understanding the problems common to exploration as an interdisciplinary science. Complaints about poor and inadequate analytical performance are not confined to exploration geochemistry. They are a common feature in mining and metallurgy and wherever sampling and analysis of "grains" are concerned - the "nugget" or "grain size effect." The "grain size" effect Poor analytical reproducibility is normal for gold and a well-defined group of other elements usually found in resistant placer minerals. Those who use and interpret geochemical data must realize and appreciate the chemical, the physicochemical, the physical and the mineralogical properties of the elements and their minerals. Especially for the "placer" minerals and their elements, such comprehensive interpretation is crucial. The most important factor to consider is the behavior of a mineral and its metal component(s) during weathering and their integration into the sampled medium, in exploration mostly sediments and soils. (Data interpretation for samples of water, gas, to a certain extent rock, follows different patterns.) A mineral may be chemically and physically stable or it may easily disintegrate physically or decompose chemically, or any combination of such processes, at varying degrees. The breakdown products, in turn, may or may not, interreact with the environment. If the nature of an element or a mineral predestines it for a heterogenous distribution in the sample medium, then nature, size and number of grains likely to occur should be considered in relation to the sample portion taken for analysis. This allows the estimation of their effect on analytical precision and accuracy. Elaborate and sophisticated statistical calculations exist on this subject. But these approaches do not cope with the complexity of the natural surface environment. The miner alogical, chemical and environmental behavior of elements and minerals can be estimated but not calculated. However, the mineral grain sizes and their influence on analytical precision can be precisely calculated if certain conditions, assumptions and idealizations are made. If the geochemical and mineralogical characteristics of minerals and elements are understood, such calculations demonstrate the grain (or nugget) effects that mineral properties and (geo)chemical behavior of minerals and elements cause on the precision and accuracy of geochemical analysis through their influence on sample homogeneity. Two other factors that influence the sample homogeneity and the nugget effect are the efficiency of sample preparation and the sample portion taken for analysis. In this way, certain element- or mineral-specific parameters can be established as a guide for the sampling program. The information, for example, may assist in determining sampling procedures in the field, especially the sample weight to be taken for "representative samples." Also, it may help assess whether analytical data, as provided by the laboratory, are acceptable. Finally, it may help determine the approach in data interpretation. However, all such simplified calculations are based on idealized, that is, unreal assumptions and conditions. As such, they represent one extreme end on the scale of probabilities. The reality is found somewhere away from this extreme, towards homogeneity. An example from a study of an eluvial gold prospect may be given for illustration: •Original sample weight: 20 kg (44 lbs) of rock gravel, crushed and ground to -0.18 mm (-80 mesh). •Au content: 20 grains of Au, average size of about 0.5 mm3 (0.03 cu in.) each = 7.5 mg each, making a total of about 150 mg Au in the sample = 7.5 ppm Au. Assumptions •Au occurs in the sample as free, discrete grains only. •Not more than one grain, if any, goes into each sample split (analyte) portion (20 grains of 7.5 mg Au each). •Analysis of original rock sample: 100 g sample for analysis, 20 kg/100 g = 200 samples 20 samples with 1 grain each: result, - 75 ppm Au. 180 samples with no grain: result, 0 ppm Au chances 1:9 •10 g sample for analysis:

Jan 1, 1996

By John O. Marsden

Process selection is the systematic development of the optun.m metal extraction route for a particular feed matenal and has two main objectives: (1) to optimize project economics, principally a function of gold recovery, throughput rate and processing costs, and to develop a process that satisfies all of the proct requirements including, for example, political and environmental considerations.

Jan 1, 1992

By Thomas E. Weyand, Wolfgang Baum

PMET is engaged in the development of reuse operations for process wastes from the natural resources industry. Most of the current remediation practices with mining wastes are concentrated on stabilization techniques. Once stabilized, valuable resources are no longer readily available for recovery and reuse. Additionally, stabilized materials, unless protected from weathering influences, pose lingering liability for the generator.

Jan 1, 1992

By D. A. Bulled

• "What does it look like?" - describes the appearance. • "How does it work?" - outlines the operation. e "Why does it work?"- explains the principles. • "What about controls?" - indicates possible automatic systems. • "How is it sized?" - discusses the necessary testwork and evaluation. • "What are the results?" - demonstrates test and operating results. • "What's the benefit?" - concludes with gains for the user.

Jan 1, 1999

By H. Z. Kuyumcu

In order to ensure a sustainable development in the mineral industries it is very important to reduce the process water consumption in mineral processing. Based on a systems analytical approach this paper deals with the most important parameters of process water management during plant operation and indicates strategies for reducing the water consumption in mineral processing.

Jan 1, 2003

By M. Phillip Jameson, Paul Sennett

The beneficiation of kaolin by flotation has been practiced on an industrial level since 1961. A brief history of industrial kaolin flotation is given, with a description of the various processing schemes used by the companies that practice kaolin flotation. Some of the areas where improvements could be made in the beneficiation of kaolin are given.

Jan 1, 1989

By Tim Avery, Steve Klein, Mark Schmoll

Tunnel boring machine (TBM) performance in hard rock is highly dependent on the geologic conditions, including the type of rock and hysical properties like the rock strength, hardness, and the spacing of the fractures. This paper examines TBM performance relative to the geologic conditions and rock mass properties at four recent TBM-bored tunnels in California.

Jan 1, 1995