Search Documents

By Marvin Barnes

The Sacaton mine is a relatively new open¬pit copper mine owned by Asarco, Inc., which has been in production only a few years. The mineral deposits consist of two ore zones; a western, near-surface zone minable by open-pit methods, and a deeper eastern zone which will have to be mined underground, probably by block caving. The copper deposits are related to small quartz monzonite intrusives implaced into Precambrian granites. Both rock types act as hosts for the copper mineralization, which has been secondarily enriched sufficiently to constitute ore. In the western zone the enriched supergene chalcocite has been subjected to postenrichment oxidation processes with partial destruction of the chalcocite blanket. The deeper eastern chalcocite zone has not been as severely affected by later supergene processes. Several mineralogical populations are represented in the total copper deposit. Leached capping overlies the chalcocite enriched zone, and in the western ore body there is a very irregular interface between the leached and enriched zone, which is complicated by oxide copper minerals irregularly distributed. Primary lower-grade chalcopyrite mineralization occurs below the enriched zone. When mining commenced near the top of the enriched zone, considerable difficulty was encountered in correlating the actual grade of ore in place with the estimated grade of the mining blocks. The mineralogical complexity and fairly wide spacing of diamond drilling made reliable grade estimation of individual ore blocks a difficult procedure.

Jan 1, 1979

By M. S. Celik, A. Aslanbas, B. Pehlivanoglu, R. Asmatulu

The principal impurities in some feldspar ores are titanium and iron, which impart color and degrade the quality of the ore. Mineralogical investigations indicate that, while titanium originates mainly from rutile with small amounts of sphene, iron originates mainly from mica minerals. Fatty acids, particularly oleic acid, are extensively used, with reasonable success, in the flotation of colored minerals from feldspar ores. In this study, potassium oleate, oleoyl sarcosine and hydroxamate were used to float colored impurities both before and after magnetic separation. Oleoyl sarcosine is found to exhibit better results compared to other reagents. Magnetic separation followed by flotation is found to produce a feldspar concentrate of superior grade.

Jan 1, 2002

By J. Kern, M. Cain, T. Torries

Until recently, the generation of electricity was regulated in all states, and the value of generation assets in a regulatory environment for ad valorem taxation were based largely on the book value of the plant plus the rate of return on capital allowed by the state regulatory agency. This method of appraising utility generation assets is inappropriate in a competitive environment because past capital expenditures are not relevant in a competitive environment. However, it is not clear what valuation methods are appropriate after restructuring. This paper identifies important problems and advantages of other appraisal methodologies and makes comments on various valuation and taxation methods.

Jan 1, 2003

By Priscilla P. Nelson, Yousof Abd Al-Jalil, Christopher Laughton

Prediction of excavation rates is a critical element in the pre-planning of a tunnel boring machine (TBM) project. A realistic evaluation of performance expectations is needed that reflects both the knowns and unknowns of the excavation process and geologic conditions. Current planning procedures are often based on deterministic “best guess” estimations. In this paper, a probabilistic approach to performance simulation is presented that will permit rational consideration of general and project-specific uncertainties in establishing realistic performance estimates. Companion to the simulation software is a database of over 600 public-domain case histories.

Jan 1, 1999

By John C. Braithwaite

Gold production commenced in New Zealand during the gold rush of 1861, and recovery to date is over 900 tonnes, almost 60% of which was alluvial. New Zealand pioneered development of bucket line dredges during the 1880's. The advent of the modern hydraulic excavator and increased gold price led to a resurgence in alluvial production with about one hundred plants in operation in 1988. The processing plants are mainly floating, with throughputs of 50-100m3/hr fed by backhoes of 20-40 tonne operating weight. Some larger plants with more sophisticated recovery systems have commenced over the last few years, with the largest using a 180 tonne backhoe.

Jan 1, 1989

By Fred W. Stuart

Microprocessor technology has revolutionized the business community by placing tremendous computing power in the hands of the end-user for a very inexpensive price tag. The range of applications covers process control, to office automation, to personal computing capabilities. With the influx of this new technology, which these systems have to offer, also comes some unique operational and control considerations. But before we address these items, let us lay a foundation of common terms to be used throughout this presentation. Due to the rapid advances in microprocessor technology, where a new generation of computers is announced every two or three years, it becomes difficult to define a microprocessor system and have it valid for an extended period of time! Therefore, for this presentation, we will be dealing with a subset of microprocessors called Personal Computers or PC's. At the heart of a PC is a Central Processing Unit or CPU. The CPU performs the actual program and command execution. The programs dealing with driving the various peripheral equipment is referred to as the Operating System (for example: DOS : Disk Operating System, CP/M - Control Program/Microcomputers, etc.). The CPU is normally housed in an enclosure which contains power regulators, peripheral equipment interfacing 'cards', and expansion 'slots' to enlarge the capabilities of the PC system.

Jan 1, 1989

By David Caiden, Petros Fortsakis, Alan Hodgkinson

"1. INTRODUCTIONDo contractual practices affect project outcome? Can better contractual practices improve the likelihood of project success? The consensus amongst experts is that better contractual practices really do improve project outcomes. With this in mind the members of the International Tunnelling Association (ITA) Working Group 3 on Contractual Practices (WG3) pooled their collective knowledge to publish in 2011 the document entitled The ITA Contractual Framework Checklist for Subsurface Construction Contracts (ITA Working Group 3, 2011). Written for projects involving significant subsurface works, e.g. tunnels and caverns, the ITA Framework Checklist explains the major contractual issues that must be considered to ensure a successful project. Its goal is not to specify how each issue should be resolved, but rather to highlight the issues and give recommendations on how they should be addressed. The Checklist is compatible with, and provides guidance for reviewing, standard contracts such as FIDIC and NEC. One of the authors is a co-author of the Checklist and has contributed to previous papers describing the Checklist and its applicability to hydropower projects (Hodgkinson & Wilson 2014, Hodgkinson & Wilson 2015). The Checklist identifies a series of issues that should be contractually defined, which can be summarized as follows: •,Methods for dealing with geotechnical uncertainties should be defined in the contract •,There should be an appropriate level of geotechnical/geological investigation •,Sufficient mobilization periods should be allowed •,Sufficient time should be allowed for testing and commissioning •,Procedures for timely dispute resolution should clearly defined •,Quality and performance requirements should be clearly defined and measurable •,Provision should exist for cost consequences of unforeseen circumstances •,Dispute resolution processes should be clearly defined •,Payment processes should be fair and clearly defined •,Risk should be clearly allocated and parties should be able to bear the risks they carry •,There should be a mechanism for adjusting payments according to conditions •,The risk management approach should be clearly defined •,Admeasurement or unit price approaches are recommended •,The responsibilities of each party must be clearly defined •,The consequences of non-performance should be clearly defined •,The construction programme (schedule) should be realistic."

Jan 1, 2016

By Omar A. Muhtadi

8.1 INTRODUCTION Several methods currently exist by which gold may be recovered from a pregnant leach liquor. Two of these methods are discussed in this chapter, the Merrill-Crowe (zinc cementation) process and the carbon adsorption process. These two methods represent the most frequently used techniques for gold extraction and are, -in fact, used almost exclusively in U.S. heap leaching operations. Because of the efficiency and ease of use of these two methods, it is extremely likely they will continue to be quite prevalent within the gold mining industry in years to come. The remainder of this chapter includes information on the history of the two processes, descriptions of the actual processes, criteria to consider in selecting a recovery process, and commercial design and construction considerations for both of the gold recovery methods. As with other chapters in this book, some fairly technical information is presented for the benefit of those readers needing a greater level of detail. However, the overall intent of the chapter is to provide an overview of the processes likely to be used in gold extraction, thus giving the reader a firm basis for more technical research into the topic, should this be needed. 8.1.1 History of Zinc Cementation During the late 18901s, zinc cementation was introduced for the precipitation of gold and silver from cyanide solutions. This occurred at about the same time as the introduction of the cyanidation process, the history of which is recapped in Chapter 1. The initial cementation process involved introduction of a gold-bearing cyanide solution onto a bed of zinc shavings. It proved to be quite inefficient because the reaction rate was very slow. The zinc quickly became "passive", inhibiting further gold deposition. Shortly after this first introduction, zinc precipitation was improved by adding a lead salt (usually lead nitrate) to the zinc. This allowed a zinc-lead couple to form on the surface of the shavings, eliminating passivation of zinc surfaces and thereby allowing continued deposition of gold. Further improvements were shortly forthcoming. The first of these involved the use of zinc dust rather than zinc shavings. This provided a much

Jan 1, 1988

By Chen Bingchen, Zhang Jian, Liu Jiaxiang

The influence of various installation angles of hydrocyclone on its operation indexes was investigated, and the correspondent mathematical models were established in this paper. The models developed in this paper can be used to the optimizing control of hydrocyclone and make the hydrocyclone as a particle size sensor.

Jan 1, 1995

By Douglas Owen

Two case studies describe the introduction of technology new to an organisation. The lessons learnt from these Case studies contribute to Our general understanding of the management of technological change.

Jan 1, 1989

By William F. Riggs

The characteristics of frothers can often be determined by the proper selection of various chemical groups. There are three basic groups utilized in the application of frothers. These are alcohols, polyglycol ethers, and polyglycols. Some of the chemical groups are separated in subgroups. Each chemical group provides particular characteristics which affect load support, bubble diameter, water retention, air dispersion, and kinetics of froth formation. These chemical groups may be preblended in various percentages to optimize frother characteristics for a particular ore deposit.

Jan 1, 1986

By V. P. Keran, K. Leung

Two 32 foot x 14% foot, 6.4 MW autogenous mills have been installed in the Mount Isa Mines Copper Concentrator to replace the fine crushing plant, fine ore bin, rod mills and primary ball mills. This paper describes the reasons for the change, the rationale for the new circuit design and configuration, the design and scale-up processes used to size the mills, considerations for the installation of large mills inside an operating concentrator and some early operating data.

Jan 1, 1992

By J. Steven Whisler

Corporate managers are facing increasingly demanding challenges as they seek to ensure compliance with environmental laws. Management also must deal with new liabilities created by environmental laws. These laws provide both private groups and governmental agencies with access to the courts to seek penalties, compliance orders, cleanups, or to forestall developments that could affect ecosystems. Environmental laws and liabilities are also affecting commercial transactions, including the availability of financing. Corporate managers must develop new and innovative methods to address these challenges in order to assure both sustainable industrial growth and stewardship of the environment.

Jan 1, 1991

By Xu Xiaohe, Zhou Jiandong, Luo Shihui, Zhang Liqun

Recently, the research and applications of ES (Expert Systern) have been put forward actively in many mining fields in China. After various ES applications or instances are introduced, the paper has especially focused on the exclusive properties of a mining system different from any other system and the problems of the existing mining ES applications. And a synthesis methodology has been introduced in order to develop a applicable ES application

Jan 1, 1996

By D. E. Hart, A. R. Walsh, Derek Maishman

In order to safely construct a ventilation and escape shaft through saturated overburden into an operating mine, artificial ground freezing and raise boring were combined for the first time on a project in the U.S.A. at Georgia-Pacific's Kentwood Mine in Grand Rapids, Michigan. Previous to drilling a pilot hole 206 feet deep into the mine, a 20 foot diameter cylinder of soil 140 feet deep was totally frozen. Before termination of the freezing operation, the pilot hole was reamed to 9 foot diameter and a 7 foot inside diameter hydrostatic steel liner was grouted in place.

Jan 1, 1991

By Dirk Timmerman, Klaus Schönert

This paper reports on the results of research on counter flow classification of - 10 µm particles. Two classifiers were designed and constructed, the first semicontinuous and the second fully continuous. The latest version operates continuously with recoveries of fines up to 90% at feed loads of 30 vol.%, separation sharpness X25/x75 up to 0.83, without bypass and cut sizes down to 1.4 µm (x50 from separation efficiency curve).

Jan 1, 1995

By G. D. Bates

INTRODUCTION The Magmont mine is a joint venture of Cominco American Inc. (operator) and Dresser Minerals, Inc. The mine-mill operation is located approximately 160 km (100 miles) southwest of St. Louis, MO, in what is commonly referred to as the "Viburnum Trend.” The Magmont mine is designed for a production rate of 3810.2 t/d (4200 stpd) on a 5-day week, three shifts per day basis. Initial production began in 1968. The mine is open stope, room-and-pillar, and essentially horizontal along the trend of the ore body. Briefly, the main geological structure can be described as a brecciated graben bounded by reverse faults. The ore body in cross section is shaped like a bell curve with some lateral extension at the lower part. Presently outlined ore is 609.6 to 762 m (2000 to 2500 ft) in width and 2133.6 m (7000 ft) in length. The ore varies in thickness from 4.87 m (16 ft) on the fringes to an average of 27 m (90 ft) in the high ore areas bounded by the reverse faults. Lead is the primary metal with zinc and copper secondary. MINE DESIGN The basic design of open stope, room-and-pillar mines has been described by several writers and need not be repeated here. (Anon., 1970; Bullock, 1973; Casteel, 1972; Christiansen et a]., 1970; and Lane, 1964) This discussion covers the mining sequence as applied to the particular problems at the Magmont mine, the use of equipment, and deployment of the work force. In the upper portion of the Magmont ore body is a layer locally called the False Davis shale. This layer lies below the true Davis shale, is normally interbedded with dolomite, is of varying thickness, and if mineralized, is included in the top pass of the mining sequence. In thick ore areas this layer will be 2.13 to 2.43 m (7 to 8 ft) in thickness and will occur in the upper portion of the pillars. Due to its incompetency the presence of this False Davis layer is of primary concern in mine planning and operation. Mining areas are divided into three basic groups by ore thickness. First are areas of ore up to 6.09 m (20 ft) in thickness. These areas are below the False Davis shale and are mined single pass with drill jumbo. Second are those areas up 13.71 to 15.24 m (45 to 50 ft) in height. The first 4.87-111 (16-ft) Pass is taken at the top of the ore and the back and pillars secured. Benching the lower portion(s) in 4.57 to 4.87-m (15 to 16-ft) passes is then done with either a drill jumbo drilling horizontally or a crawler drill drilling vertically. Normally these areas are below the Table 1. Productivities per Manshift False Davis shale. These areas may also be mined by back slashing, or overhand benching, where the first 4.87-m (16-ft) pass is taken at the base of the ore and successive 4.87- m (16-ft) passes are taken upward. A minimum amount of back slashing is done at Magmont since it requires repetition of roof control on each pass and roof control is the single largest stoping cost at Magmont. Ore left to provide a working platform oxidizes and is coated by oil spills thus reducing metallurgical recoveries. The third mining area is over 15.24 m (50 ft) in height UP to a maximum of 40.23 m (132 ft) and will encompass the False Davis shale. These areas are mined by first driving +15% inclines to the top of the ore body. The top pass is mined and the back is bolted and roof mats installed as a matter of standard practice to minimize roof problems as mining progresses downward. Once the back and pillars on the top pass are secured, benching begins on successive passes with either the drill jumbo or crawler drill. Pillars on all successive passes below the top pass are secured as necessary. While benching progresses below the top pass, the pass at the base of the ore body is mined leaving a sill of 4.57 to 7.62 m (15 to 25 ft) in thickness to be removed with the crawler drill in a retreating manner. Rooms are mined on a 1.57 rad (90") grid pattern to insure alignment of pillars where multiple passes are taken. Pillars are designed on a 17.98-m (59-ft) spacing with rooms up to 10.66 m (35 ft) in width. Heading widths are wide enough for the mobile equipment to turn without additional allowance for curves. The result is a flexible layout which provides a maximum number of headings available for high extraction rates and grade control. PRODUCTION Incentive Bonus Incentive bonuses play an important part in the mine production at Magmont. Production crews are trained to perform only one of the mining functions of drilling, blasting, mucking. or roof bolting. This specialization, or functionalization, is augmented by development to open all possible stoping areas as early as possible in the life of the mine. This insures that each crew will have enough headings to perform its specialty. The incentive bonuses increase exponentially as output increases. The lucrative incentive bonus coupled with the specialization of the production crews and proper mine development have combined to give the high productivities shown in Table 1. Development crews perform all mining functions in their area. The incentive bonus is paid on a per foot basis, Crews on different shifts working the same heading share equally in the bonus proportional to their contract hours worked.

Jan 1, 1982

By A. Mai, J. S. Wakeman

The progress results of a pilot plant study on the effects of ball top size and other mill operating parameters are reported. Test series on taconite and quartzite crude ores using a 1.7-m diam primary mill in closed circuit with a vibrating screen indicate clear trends on the improvements of mill throughput and power consumption when using larger diameter balls. Possible effects on mill liner and ball consumption as well as future research plans are discussed.

Jan 1, 1987

By L. G. Austin

Development of an equation for tumbling charge and balls plus comparison to plant data suggests that the net mill power for cylindrical semiautogenous mills can be calculated from

Jan 1, 1991

By Persio de Souza Santos, Ayres Ferrelra Morgado

In this work, a sample (of about 100kg) of an ore considered as smectitic, not yet industrialized, from Lages-SC-Brazil, was tested for evaluation of its industrial applications. First, we characterize them by XRD, DTA, FRX, and CEC analysis. After this, the smectitic clay was changed to sodium form by treatment with sodium carbonate. Then, the homoionic sodium clay was tested for iron ore pelletizing agent, as binder of foundry sands, and drilling mud with good results.

Jan 1, 1998