Search Documents

By D. S. Holmes

Biological processes for metal solubilization and ore beneficiation are in widespread use today. There are also some promising new applications of biotechnology in the areas of metal concentration and toxic metal cleanup. Recent progress in genetic engineering promises both to revolutionize the existing biological process and to expedite the adoption of the new biological applications. But before it can do so effectively, progress must be made in many areas of fundamental research and in biochemical engineering. These issues are addressed with special reference to the biotechnology of semi-enclosed containers (bioreactors), dumps, heaps, in situ and under- ground leaching, and with respect to the biotechnology of metal concentration. Finally, certain biological considerations for bacterial strain improvement are discussed.

Jan 1, 1987

By D. H. Carlson, J. H. Johnson, C. F. Renders

Research was conducted at a western coal mine on a wide variety of underground mining vehicles to develop testing procedures for portable instrumentation monitoring of tailpipe concentrations of diesel particulate matter (DPM), carbon dioxide (CO2) carbon monoxide (CO) and nitric oxide (NO). DPM was measured using the Emissions Measurement Appa¬ratus (EMA) developed by Michigan Technological University (MTU), and an ECOM-KL five-gas analyzer was used to measure gaseous tailpipe concentrations. Baseline concentrations of the tailpipe pollutants were measured using vehicle systems to load the engine. Concentrations before and after the water scrubber were measured and water scrubber efficiencies were estimated by calculation. Field measurement procedures were established. Heavy-duty vehicles with automatic transmissions were loaded using the torque converter to stall the engine. Consistent engine loading for light-duty vehicles with manual transmissions involved placing the transmission in neutral and adjusting the throttle to maintain a constant engine speed of 2,500 rpm. Tailpipe CO2 concentrations for Caterpillar 3306 and 3304 engines were compared to laboratory CO2 data from Caterpillar and MSHA to help determine if engine settings were correctly adjusted for operation at high altitudes. (Perfect agreement between the mine vehicle tailpipe and laboratory measurements would not be expected because of the differences in the test conditions.) DPM concentrations for light-duty vehicles ranged from about 20 to 160 mg/m3, and one light-duty vehicle averaged near 1,000 mg/m3. DPM concentrations for heavy-duty vehicles ranged from about 55 to 200 mg/m3. Widely ranging DPM concentrations for a particular vehicle type reflect the state of maintenance, fuel rate settings and different engine loading procedures as well as differences between samples collected upstream and downstream of the waterscrubber. The calculated DPM removal efficiencies due to the water scrubber varied considerably between vehicles, ranging from 13% to 51%. Calculations indicate that, under worst-case conditions, very large reductions in DPM may be required to meet the proposed DPM PEL of 0.15 mg/m3, even on vehicles with water scrubbers. In-mine ambient air studies, which are needed to actually measure the impact of the tailpipe concentrations on the work environment and the effect of mine ventilation on the dilution of DPM were not done in this first set of tests.

Jan 1, 2000

By Frank R. Cappuccitti

This paper will deal with current market trends for sulfide mineral collectors in three distinct parts; the global market for sulfide collectors, collectors as tools to solve mineral processing problems and new collector Research in the 1990's. The global market and manufacturing of sulfide collectors will be detailed as well as the trend towards using increasing amounts of specialty products. The use of Total Quality Concepts for laboratory and plant evaluations of new products will also be discussed. Research in the 1990's for sulfide collectors will need to focus not on the development of new chemical species but on the application of the new technologies that have already been developed.

Jan 1, 1994

By S. Subbarayan, S. Chander, M. S. Klima

A laboratory study was conducted to investigate the potential for recovering anthracite from coal preparation-plant tailings. The study included washability analyses, cyclone simulations and froth flotation testing Samples were collected from either the tailings streams or the slurry ponds of five anthracite-cleaning plants. From each sample, a washability analysis was conducted on the 28x100 and 100x200-mesh fractions. Using the above data, along with published partition data, simulations were performed with various cyclone-staging arrangements for both water-only and dense-medium cyclones treating the 28x200-mesh fractions. Separate froth -flotation tests were conducted on the 28x100- and 100x200-mesh fractions from three of the plant samples. The washability, simulation and flotation results are presented as grade-yield curves.

Jan 1, 1996

By Liguang Wang, Roe-Hoan Yoon

The thin film balance (TFB) technique was used to measure the equilibrium film thicknesses (H3 between two air bubbles in sodium dodecyl sulfate (SDS) and electrolyte (NaCl) solutions. The results were used to determine the magnitudes of the hydrophobic forces (K232) using the extended DLVO theory. The Km values determined from He measurement allowed us to predict disjoining pressure isotherms, which were found to be in excellent agreement with those obtained experimentally using a bike-wheel film holder. The rate of film thinning was measured at low SDS concentrations with varying amounts of electrolyte (NaCl) added. In general film thinning was controlled by the capillary pressure during the initial stages, while it was controlled by the surfaces forces during the later stages. At low NaCl concentrations, it was possible to predict the rate of film thinning using the Reynolds equation, provided that the driving force was corrected for the contributions from the hydrophobic force, which in turn were determined from the KZ32 values obtained from the He values measured experimentally. At high NaCl concentrations, where it was difficult to measure the equilibrium film thicknesses, the contributions from the hydrophobic forces were determined by fitting the film thinning data to the Reynolds equation. The K232 values obtained using both the equilibrium film thickness and the film thinning measurements showed that hydrophobic force deceased with increasing surfactant and salt concentrations. It was found that the hydrophobic force in foam films was very sensitive to the added electrolyte concentration.

Jan 1, 2005

By Jean-Luc Cornet

Advances in conveyor technology over the past decade have enabled the design and erection of very long overland belt conveyors. Such conveyors usually require head and tail drives to lower the belt tension and belt strength required. This paper provides an overview of the problems encountered in controlling the head and tail drives on such conveyors and some of the solutions developed by CDI for several such projects.

Jan 1, 2002

By M. P. Hardy, C. J. H. Brest van Kempen, H. N. Maleki

To evaluate the influence of uniformly tensioned roof bolts on roof stability, mechanically anchored roof bolts were installed using the conventional bolter and a specially developed thrust and torque controlled retrofitable box mounted on a bolting machine. Thirteen thousand bolts were installed over 19 crosscuts in a 4 heading development in an operating coal mine. Geological , bolt and mine parameters were recorded at bolt installation, and bolt tension histories, roof sag and other changes evident in the rooms, crosscuts and intersections were recorded over a 2 month period. In all, 24 variables and 11 responses were quantified at 67 bolt clusters. These data were analyzed statistically to determine the significant variables influencing roof stability. As the mine development was safe and stable during the monitoring period, roof sag after two months was used as an index to quantify "stability." The variables of significance were shown to be coefficient of variation of bolt tension, bolt anchorage capacity, roof lithology, roof shape, standard deviation of bolt tension, and dip of roof lithologies. It was concluded that of the variables with which the mine operator has control, bolt tension uniformity was the most significant parameter at this mine. Other variables, such as intersection type and time between mining and bolting , were not significant, whereas, some other potentially significant variables such as horizontal stress or roof joint frequency did not vary sufficiently for their influence on stability to be evaluated.

Jan 1, 1986

By J. Engesser

A research project was undertaken to determine if coal addition tofluxed-magnetite pre-fired pellets would reduce nitrogen oxide (NOx)emissions during pellet induration. Iron oxidation rate tests, coal oxidation rate tests and calcination rate tests were conducted in a laboratory furnace to determine the amount of coal necessary to provide adequate heat for limestone calcination without producing detrimental effects to magnetite oxidation. Pilot scale pot-grate tests were then performed with and without coal in the pre-fired pellets to verify pellet quality parameters and nitrogen oxide emissions. The off-gas during each pot-grate test was analyzed for NOx, CO2, CO, SOx, and O2. There was approximately a ten percent reduction in NOx emissions with coal addition during the normal pot-grate firing cycle. There was a 75% reduction in NOx emissions during firing cycles that used 25% to 75% excess air during firing rather than the normal 300% excess air.

Jan 1, 2003

By James L. Parks

This paper describes improvements in SAG and AG mill liner designs and their cumulative effect on wear life and mill availability. Routine procedures used by many SAG and AG mill operators to improve liner life are reviewed. Guidelines are provided for estimating the time required to replace worn liners along with practical methods to reduce downtime for liner replacement. Finally, the effects of mill operating conditions on liner wear life and breakage are considered.

Jan 1, 1998

By J. J. Carlson

Studies were carried out to determine whether filtration rate changes observed in an iron ore concentrator were due to variations in particle shape. It was confirmed that ores mined from different locations differed in filtration rates by as much as 60%. However, when image analysis was used to quantify the shapes of the individual particles in the filtration feed, it was found that the particle shapes showed almost no variation, and the shapes did not correlate with the filtration rate. It was also determined that the filtration rate variations were not caused by changes in particle size distribution. These results suggest that the differences in filtration rate are due to factors other than size and shape, such as surface chemistry.

Jan 1, 2008

By W. Lin, E. Heuze

This paper focuses on tests performed on sandstones and shales from four gas wells in the Mesaverde formation. A previous document showed a comparison of the static and dynamic laboratory moduli. This publication describes how field velocity logs were used to derive field dynamic moduli. A 3-way comparison was then performed for these stiffness properties; the results show no agreement between the three sets of values. Differences between dynamic stiffness coefficients from the field and the laboratory exceed 200%; differences between static and dynamic coefficients range up to 600%. In turn, this indicates that a reliable method of estimating mechanical rock properties for hydraulic fracturing design has not been established, and that such a task should be pursued.

Jan 1, 1986

In 1988, at the request of members of the Society for Mining, Metallurgy, and Exploration (SME) Inc., the president of SME formed Working Party No. 79, Ore Reserve Definition. Its mission was to develop guidelines for the public reporting of exploration information, resources and reserves. These guidelines were published in the April 1991 issue of Mining Engineering,(pp. 379-384), and as a document entitled "A Guide for Reporting Exploration Information, continued on an ad-hoc basis until 1996. Working Party No. 79 was then renamed the SME Committee on Re¬sources and Reserves and became a standing committee. Since 1994, the Council of Mining and Metallurgical

Jan 1, 1999

By J. A. Brierley, C. L. Brierley, K. A. Prisbrey, R. W. Bartlett, J. G. Harrington

Bacterial oxidation of gold-encapsulating sulfide minerals in low-grade refractory ores was investigated over a period of one year. Crushed ore samples were held in wet, bacteria-inoculated, aerated columns. Sulfide mineral oxidation data were correlated with subsequent gold cyanide extractabilities. Experimental results for both sulfide conversion and gold extraction were compared with a biooxidation kinetics model that incorporates rock size, mineral grain size, and heterogeneous pyrite reaction kinetics. Using the model, extrapolations were made over three years for biooxidation of ore in large stockpiles. Ferric ion (oxidant) diffusion in the solution-filled pores of the rock matrix does not control the biooxidation kinetics of ore crushed to -25 mm.

Jan 1, 1993

By R. L. McNearny, K. A. Barker

Four numerical models written with the "PFC2D " program were compared against four similar physical models. The numerical models were constrained numerically to closely follow the caving behavior of the physical models. Results from the numerical analyses closely simulated both the granular and blocky behaviors of the physical models, including bridging and interlocking of the simulated orebody during draw. The drawdown patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. The same assumptions and governing parameters used in analyzing the first four models were applied to an additional model. The fifth model employed a completely different, uneven, draw sequence than the other four models, allowing the material to flow in a more granular manner with a demonstrated instability of the undercut sections between each drawpoint opening. Drawdown patterns and behavior of the numerical material of the first four models progressed at uneven and inconsistent rates, similar to those seen in the physical models. By inspection, the overall shape and flow lines of both the numerical and physical models were close in the area removed and in the flow characteristics. The fifth model proved to be the most unstable of all the models tested, with poor correlation to the physical models. The uneven draw sequence, coupled with an additional frictionless wall condition and an added drawpoint, caused the material to flow in a very granular manner. Information generated by this study can be used as a first approach in determining the proper draw rate, drawpoint spacing and undercut thickness for a block-caving operation. Numerical models are often difficult to predict and interpret. However, this study should increase the confidence level for use of the PFC2D program in the future.

Jan 1, 2000

By L. Shwydiuk, A. Chrzanowski, W. Newcomen, G. Bastin, R. Wilkins

Automated monitoring of steep embankments allows the early detection of instability and can be used to avoid or mitigate possible slope failures. A system that uses multiple and different types of sensors has been created and successfully tested at the Highland Valley Copper mine in British Columbia. The system uses robotic total stations (RTSs) as the primary measurement sensor, with surveys repeated at predefined intervals selected to optimize operational efficiency. A methodology has been developed to improve the system’s accuracy and reliability by reducing the effects of systematic errors created by atmospheric refraction and unstable instrument and reference point positions. The inclusion of GPS sensors to monitor the RTS positions creates additional operational flexibility and maintains system integrity when insufficient reference stations are available.

Jan 1, 2003

By Louis W. Cope

The various types of placer deposits will be described as an introduction to the subject. The several methods and machines used for sample taking and processing will be discussed. The advantages and disadvantages of each will be covered. Included will be mistakes and pitfalls of placer sampling and sample reduction.

Jan 1, 1987

By J. A. Herbst, Y. C. Lo

An attempt has been made to parameterize the population balance model for a ball mill based on measurements of the elementary breakage process obtained using an ultrafast load cell device. Detailed insight obtained concerning the fragmentation of particle assemblies with the ultrafast load cell leads to a better understanding of ball mill grinding. The ball mill breakage function and specific selection function are derived from an average single event representing the multiple breakage events which occur in ball mill grinding. Since both the breakage function and the specific selection function depend on the loading mode in the mill, predictions of breakage mechanisms in ball mills are possible by using data obtained in various elementary loading modes. The application of this model to the description of batch ball milling behavior has resulted in reasonably accurate predictions of product size distributions for various energy inputs.

Jan 1, 1992

By B. R. Reddy, P. V. R. Bhaskara Sarma

A process for the separation and recovery of cobalt and nickel was optimized for a sulfate leach solution of Indian Ocean sea nodules containing 80 g/m3 cobalt and 730 g/m3 nickel using the sodium salt of Cyanex 272 as the extractant. Extraction of both cobalt and nickel increased with an increase in equilibrium pH and extractant concentration. The extracted species with respect to cobalt appears to be CoA2.3HA. More than 99.6% extraction of cobalt was achieved using 0.04M solvent in a three-stage counter current simulation at the A:O phase ratio of 3:2. The co-extraction of nickel was about 0.6% only. Two-stage countercurrent stripping of cobalt from the loaded organic at an A:O ratio of 1: 7 resulted in a pregnant electrolyte enriched by 0.8 kg/m3, thus enabling a ten times overall enrichment of cobalt. From the cobalt free raffinate, nickel extraction was carried out using 0.25M solvent in two countercurrent stages, and the extraction showed a 99.8% recovery. Stripping of nickel from the loaded solvent was carried out at an equal phase ratio with the advance electrolyte of pH 1.75 in two countercurrent stages. The nickel stripping efficiency was found to be 98.8%. The present studies indicated that complete recovery of cobalt and nickel was possible using nine counter-current stages.

Jan 1, 2002

By Michael J. Shulman

During-all phases of exploration limited resources must be allocated among exploration methods and among exploration prospects. This problem,, an exercise in optimization, can be treated mathematically. For three objective functions - maximizing return, return to cost and return minus weighted cost - theoretical results exist which enable the exploration planner not only to gain valuable insight into the problem, but also to estimate the resources necessary and to allocate these resources for' at least-two stages of exploration prior to initial field work. A two-stage exploration strategy for volcanogenic-sedimentary iron in northern Egypt illustrates, how the results can be used. Stage 1 consists of an aeromagnetic survey to map the structure of five areas;" stage 2 consists of field reconnaissance work. For the three objectives, lower bounds are calculated as a function of exploration expenditures for each stage in order to facilitate the choice of an-optimal exploration budget. Nomograms are then presented which, based on the Kuhn-Tucker Conditions', enable the incremental allocation of airborne and reconnaissance effort among the five areas.

Jan 1, 1989

By J. D. Miller, J. Hupka

Environmental applications of the air-sparged hydrocyclone (ASH) technology are presented. The original ASH design used porous sintered steel or porous polyethylene tubes as spargers. To diminish/prevent plugging and to reduce pressure head loss in the gas path a wire screen sparger and new hydrocyclone design have been developed, which allows for wide application of the technology to solve environmental problems and to be used as a chemical reactor. Field and laboratory trials have shown that the ASH technology might be preferred for the stripping of volatile organic compounds WOC) from contaminated water. The ASH has also been developed for absorption of SO2, toluene vapors, and for the recovery of cyanide.

Jan 1, 2005