Search Documents

By Kurt Egger, Emily A. Baker

Rehabilitation work at the Cameron Run Tunnels entailed the restoration of seven heavily deformed, approximately 69 m long, steel liner plate supported culverts through a CSX Railroad embankment near Alexandria, Virginia. A custom fabricated expander, equipped with four 200-ton hydraulic jacks on two expansion arms was used to push back the liner plates encroaching into the proposed tunnel profile and install the steel set support. In a second phase the tunnels were then lined with 16 cm of fiber reinforced shotcrete. Geotechnical instruments both in the tunnels and on the railroad embankment were used to monitor the effects of the rehabilitation work on the two CSX Railroad tracks above the tunnels. Freight and passenger trains were required to run uninterrupted and at maximum speeds throughout construction.

Jan 1, 2003

By John A. Herbst

Mathematical models of mineral processing unit operations have been developed and used for a variety of purposes. Models, defined as equations which mathematically approximate the behavior of process units, are being employed in simulators to evaluate proposed flowsheets, to investigate flowsheet modifications, to study the effect of variables on circuit behavior, to optimize the performance of circuits off-line, and to compare alternate control strategies (Mular and Herbst, 1978). Models developed for mineral processing operations may be placed in one of two general categories: phenomenological (based on mechanism) and. empirical (based on experimental data only). Dynamic models (including time as a variable) .are useful for control studies, while steady-state models (independent of time) are employed in flowsheet evaluations. Phenomenological models are potentially more flexible and accurate than empirical models. However, models constructed from theoretical knowledge are less easily developed compared to empirical expressions fitted statistically to experimental data. The latter apply only over the range of data acquired. Most often, models used in practice are the result of a combination of theoretical and empirical approaches.

Jan 1, 1979

By Palmer C. Sweet

By-products from mining and processing plants and coal-fired power plants are being utilized more as valuable resources in Virginia. Mining-related by- products are divided into two categories: those generated from mineral extraction and beneficiation, and those generated from mineral processing or from industrial plants. Materials from both categories are produced in Virginia, where by-products have been exploited for various uses in the past and/or present. These materials include coal- combustion products (fly ash and bottom ash), lime-kiln dust, flue-gas-desulfurization residue, rock fines, magnetite, Cold Spring clay (kaolin), Austinville tailings, soapstone rock, and calcium-carbonate paste. Some of these by-products have never been utilized, although several ideas have been investigated over the years.

Jan 1, 1999

By Sara J. Heinlein, George Malkos, James E. Lindell, Tony Pestonatto

The 79th Street Water Tunnel Extension Project was initially designed by the City of Chicago, Department of Public Works, to increase the capacity of the City’s south side water distribution system. MWH preformed a design review, prepared the final design and provided construction management for the City of Chicago Department of Water. Construction commenced in September 1995 and was completed in October 1999. The Project connected two existing water tunnels with a new 5.8 km (19,044 ft.) long, 4.9 m (16.08 ft.) finished diameter concrete lined rock tunnel utilizing TBM, drill-blast and mechanical hoe-ramming methods. In addition, approximately 61 meters(200 feet) of concrete lined variable cross section tunnel, a new gate shaft and a temporary construction shaft were constructed. This paper describes the construction of these features and the geological conditions encountered.

Jan 1, 2003

By Martin Knights, Geoff Featherstone, John Flanagan, David Lawrence

The proposed paper will address specific transport, engineering, environmental and community related issues concerning the current construction and future operation of Europe’s biggest urban road tunnel project—the US$500m Dublin Port Tunnel. Situated in Ireland’s capital, the three mile long, 40 ft diameter twin tunnel project encounters a range of ground conditions using TBM, Shield, Cut & Cover with diaphragm walling and major slope stabilisation and Multi-jacked pipe techniques. Where possible units of measurement are given in feet and inches.

Jan 1, 2003

By V. R. Degner

Given: the process tonnage, performance objectives, and plant floor area, the paper will outline the metallurgical and machine hydrodynamic scale-up procedures for translating the lab flotation test results to the design of a full size flotation machine installation, including the machine number, size, and arrangement. Machine selection considerations for rougher, scavenger and cleaner duty, and special considerations relative to specific applications, will be summarized where appropriate. The value of kinetic modeling in quantitative metallurgical (lab to full size machine) scale-up will be reviewed considering a coal installation, and design information for additional applications such as copper, molybdenum, iron, phosphate, and potash will be discussed.

Jan 1, 1986

By Y. Topkaya, Lloyd Petrie, Dianne Marozas, R. E. Johnson, Steven Paulson, J. H. Canterford, B. R. Palmer, R. B. Bhappu, Lorin Redden

This paper describes a fundamental approach to in situ leach mining (ISLM) lixiviant development which emphasizes leaching selectivity through detailed characterization of mineral-solution interfacial chemistry and post-leach geochemistry. This experimentation and modeling approach consists of: (1) petrographic identification of reactive ore and gangue minerals; (2) determination of leaching kinetics of individual minerals through batch leaching tests; (3) evaluation of bulk solution geochemistry through column leaching tests; and (4) ISLM simulation of element species transport and geochemistry through core leaching tests. Recent results confirm good leaching selectivity for manganese, but reveal post- leach precipitation and permeability loss during core leaching experiments.

Jan 1, 1993

By Carl E. Nelson

Shallow epithermal stockworks hosted by maar eruption craters contain over ninety percent of the bulk mineable gold identified to date in the Circum-Caribbean region. Pueblo Viejo (Dominican Republic) and Santa Rosa (Panama) contain combined gold reserves of over 600 tonnes. Bulk mineable gold deposits are also being discovered in and around veins that were formerly mined underground. Bellavista, El Recio and San Martin (Costa Rica) contain combined announced gold reserves of over 50 tonnes. Representative rock suites collected at 8 bulk mineable gold deposits include 291 samples of veins and vein stockworks, hydrothermal eruption breccias, sinter, variably altered host, unaltered host, nearby intrusive rocks and basement. Analyses completed to date show that Circum-Caribbean epithermal ores are enriched in arsenic, mercury and antimony as well as gold and silver. Exploration efforts in the region naturally focus on districts with past production. However, an order of magnitude more bulk mineable gold has been discovered in shallow epithermal stockworks outside of the old bonanza vein camps. Exploration guides include basal island arc volcanic sequences, hydrothermal and hydrovolcanic (maar) eruption breccias, thinly-bedded carbonaceous maar sediments, and hot spring-related silicification and argillic alteration.

Jan 1, 1990

By Randy Sandrik

Sampling has evolved at two large underground limestone mines as conditions and product requirements have grown tougher over 100 years of mine life, requiring innovative techniques to insure delivery of high purity limestone. Sampling insures delivery of consistent product to customers at the lowest possible cost. Statistical considerations have evolved from simple data collection to predictive and process capability analysis. Sample methods include borehole samples, face (using a proprietary face-sampling device), and total plant feed automatic, process, and final product sampling. Lessons learned, while keeping costs at historically low numbers, include the importance of geological models, exploration drilling density, face sampling, and blending of ore.

Jan 1, 2005

By Charles H. Jacoby

In 1960 the management of International Salt Company made the decision that all waste material from the Watkins Glen plant would be stored in underground salt cavities. The cavities which they contemplated using had been depleted of salt to a point where continued operation would have impaired their structural stability. Originally, the waste to be disposed of included vacuum pan bleeds, cinders, contaminated salt and sewage. It was proposed that this material, in a slurry form, was to be injected into the salt cavity through one of the abandoned wells. Brine, displaced from the cavity, was to be recovered from an adjacent well and subsequently injected into the Cherry Valley limestone, This Cherry Valley limestone which underlies a large portion of north central New York contains a connate water with high concentrations of ammonia, hydrogen sulphide and the chlorides of calcium, magnesium and sodium. A number of questions were immediately raised on various aspects of the technical feasibility of the project. Of major concern was the buildup of insolubles adjacent to the bore of the injection well. Another pertinent question was the carryover in the displaced liquor of finely-divided, mechanically-suspended particles. Criticism was leveled at the inclusion of sewage. Engineering studies were started by the company's Mineral & Mines Development Department and on April 3, 1961 a preliminary feasibility report was issued.

Jan 1, 1973

By J. H. Rowland

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on the effectiveness to extinguish conveyor belt fires. The four different types of suppression systems were water sprinkler, deluge type water spray, and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 72-in-wide fire resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 500-550 feet per minute (fpm) and 1350-1500 fpm. Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to extinguish any smoldering belting was greater than the current MSHA regulations require. MSHA regulations only require 10 minutes of water supply to the suppression system. In the test set up neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 500 fpm air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test set-up, arrangement of the fire suppression systems, and conclusions regarding the effect of air velocity on fire suppression system design and performance. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009

By Paul Grisley

Air-supported belt conveyors-conveying systems that replace troughing idlers with a film of air-were a revolutionary concept when introduced in the 1970s. But high installation and operating costs limited their application. Now, system refinements have led to successful applications, even under the challenging conditions of mines and process plants. In this presentation the author will discuss the latest developments in the engineering of these systems, including the ability to retrofit existing transfer points with modular air conveyor components. Air conveyor applications and limitations in mineral-handling operations will also be examined.

Jan 1, 2002

By H. Nakazawa, A. S. Malicsi, K. J. Reid, P. J. Ryan, I. Iwasaki, P. W. Weiblen

Precious metals are commonly believed to be recovered along with sulfide minerals in flotation, but a few neutron activation analyses showed that the recoveries of gold and silver were unexpectedly low. Reasons for low recoveries of platinum group metals remained unresolved due to interferences in the analyses. Electron microprobe, scanning electron microscope, and scanning Auger microprobe analyses have identified nickel arsenide minerals in the ore and confirmed a close association of platinum group metals with the arsenide minerals as minute inclusions. These results indicated a need for re-evaluation of flotation procedures that have so far ignored special problems related to arsenide minerals. The electrochemical and flotation behaviors of nickel arsenide and their application to the flotation recoveries of precious metals from copper-nickel bearing Duluth gabbro are presented.

Jan 1, 1987

By Robert Mullen, Patrick K. Sollars

In 1994, Cyprus Twentymile Coal Company and Scandura formed a joint task force charged with the purpose of developing the highest rated fabric belt for underground longwall coal mining. This paper details the development efforts and concepts utilized by Cyprus and Scandura to meet the challenging demands of Twentymile Coal's East Mine District (EMD). The finished panel consisted of a 5,500 meter (18,000 feet) conveyor with 245 meter (800 feet) of drop over the first 3,660 meters (12,000 feet) and 245 meters (800 feet) of lift out-by over 1,830 meters (6,000 feet). The panel was designed with an operating capacity of 4,500 tph (5,000 stph) and 4.1 m/s (800 fpm) belt speed.

Jan 1, 1998

By B. J. Arnold, B. W. Parker

Rosebud Mining Company added a classifying cyclone/spiral concentrator circuit addition to its McVille Preparation Plant, Freeport, PA, in mid-2002. This paper will describe the plant addition, which was implemented fully by plant staff, and review improvements in cleaning plant performance and economics.

Jan 1, 2003

By R. B. Steele

The paper contains the results of the physical and mathematical simulations (based on the finite elements simulation) of the length and shape influence on the mechanical strength of the brex. Key words: Stiff extrusion, extruded briquettes, BREX, mechanical strength, cold strength, compressive strength, tensile splitting strength, oval shape, finite elements simulation. INTRODUCTION Extruded briquettes (BREX) exhibit a set of unique properties when compared with briquettes formed by alternative methods. Brex generally have sufficient integrity right after extrusion to withstand the necessary handling and stockpiling and does not require any special means and tools for the green briquettes strength conservation. In a typical die without an ancillary cutting device green brex tend to have very high length to diameter (L/D) or length to section area ratios. For round hole dies the brex are typically 5to 6 times the diameters and even longer. Stiff-extrusion allows also for the very easy changing of the forming dies. Dies with different cross-sectional shapes of the brex (round, ovals, square, hollow structures and many other two dimensional shapes) are possible, and common. The results of our investigations show how these geometrical shape factors contribute to overall quality of the brex both in terms of strength and as new charge components in metallurgical furnaces and processes [2-4]

Feb 27, 2013

By D. W. Fuerstenau

In mineral processing, the last century of the current millenium has been the century of froth flotation. The process did not result from fundamental research, but was developed over the years by empirical methods. In more recent years, our understanding of the fundamental principles of the flotation process have made significant strides. This paper reviews some of the historical perspectives of developments in flotation reagents, the development and application of experimental tools for delineating flotability and interfactial phenomena, advances in flotation fundamentals, and the development of flotation kinetics, both macroscopic and microscopic subprocesses. Through the application of surface chemistry, the flotation process has permitted economic utilization of a vast array of complex ores.

Jan 1, 1999

By J. A. Brierley, C. L. Brierley

The history, current applications and future of biotechnical developments in the metals' extraction industry are reviewed. Bioleaching of copper minerals continues to be the most significant application. Uranium bioleaching was successfully demonstrated at industrial scale. Developments are now being made in biooxidative pretreatment of refractory gold concentrates, ores and low-grade materials. Advancements are forthcoming in water and solid mine waste bioreclamation, including metals' biosorption, wetland treatment of acid mine drainage, and biodegradation of cyanide in spent, heap-leach operations. Better understanding of the types and functions of microorganisms involved in metal interactions could advance genetic engineering applications in bioleaching and bioreclamation.

Jan 1, 1993

By Henry N. McCarl

From the earliest use of crushed and broken stone as landfill for eroded gullies in trails and roads, to the mixing of sand and gravel with cement to make concrete, men and women have found mineral aggregates to be useful materials in satisfying human wants. Crushed stone, sand and gravel, volcanic cinders, pumice, manufactured lightweight aggregates, slag, cinders, expanded perlite and vermiculite, and a great array of recycled materials such as grog (broken or crushed brick) and fly ash have served as mineral aggregates. These materials have provided bulk and strength in portland cement concrete, bituminous concrete, road base, fill, concrete block, and plaster and stucco finishes. Mineral aggregates provide many special characteristics such as compressive and tensile strength, surface textures, weight and density, thermal and acoustical insulation, abrasion resistance, and impermeability to various concrete products and mixes. While most materials used as mineral aggregates are consumed on the basis of their low unit values, the large volumes extracted in the United States each year make them one of the most valuable mineral resources in current production. In 1960, US production of construction aggregate was just over a billion tons per year (Meyer and Zelnick, 1991). Two decades of accelerated interstate highway, residential, and commercial construction brought the total annual production of mineral aggregates to roughly 1.4 Gtpy by 1970 and just over 1.6 Gtpy by the late 1970s. General economic and related construction slowdowns in the early 1980s saw annual US production of aggregates fall to below 1.1 Gt in 1982, and then rise to just over 1.7 Gtpy in 1990, a new peak in mineral aggregate production and use. Per capita annual consumption of mineral aggregates was approximately 5.68 t/capita in 1960, 6.89 t/capita in 1970, rose to a high of 7.25 t/capita in 1979, and has since settled to just under 7 tpy for every man, woman, and child counted in the United States Census of 1990. The value of these materials came to approximately $9 billion in 1990. During the period 1960-1990, roughly half of all mineral aggregates were used in the construction of residential, commercial, and industrial structures, and the remainder was consumed in highways, bridges, and other transportation facilities such as railway roadbeds, airports, and water-related projects (Meyer and Zelnick, 1991). During the period 1988-1992, public works (highways, waterway projects, road maintenance, etc.) represented closer to 60% of annual mineral aggregate demand with residential and non-residential construction approximately 40%. The growing market share of public works projects has been mostly due to the dramatic slowdown in residential, commercial, and industrial construction during the 1988-1992 period.

Jan 1, 1994

By Joel Nonnweiler, David Young, John Hawley

The Sacramento Regional County Sanitation District has implemented a billion-dollar interceptor system master plan, including the 31 km (19 mile) long Lower Northwest Interceptor (LNWI). For the two LNWI Sacramento River crossings, pipe-jack/micro tunnel drives in excess of 300 meters (1,000 ft) from 30 meter (100 ft) deep shafts in mixed soil conditions below the water table were considered, as were600 meter (2,000 ft) tunnel drives utilizing pressurized-face tunnel boring machines. Operation and maintenance concerns, predicted flood scour, and levee concerns are discussed. A risk assessment process was used to select both profile and construction method. Construction will begin in mid 2004.

Jan 1, 2003