Search Documents

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations. Key words: Mineral liberation, Flotation, Image analyzers

Jan 1, 2003

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1988

By Alban J. Lynch, Khairun Azizi

Education and research have always followed production in the mineral industry. Almost all of the leading mineral education and research units in the world today are in developed countries which had strong mining industries created during the 19th and 20th centuries to meet the demands for minerals due to the Indus- trial Revolution. It is in those countries where the main advances in mining and metallurgical technologies have occurred. But it is in the developing countries, often with traditions which have not favoured engineering initiatives, that the mineral industry is growing. Legislative changes and high exploration expenditures in many of those countries are of such a nature that many mineral discoveries will be made and mines and plants built in them during the next decades. Developments must be accompanied by increased activities in education, research and technology transfer in mining and processing, particularly those which are computer based. Malaysia is a developing country with the objective of achieving developed status by 2020. It has a short history of tertiary education and industrial research and a growing mineral industry. It is now building the education and research programs which will give strong support to its mineral industry. The progress which is being made in the computer based components of these pro- grams, and the factors which influence them, are discussed.

Jan 1, 1996

By H. Douglas Dahl

In order to provide a reference framework for discussing the applicability of drilling technology to shaft construction in coal mining ventures, it is meaningful to review the history and nature of United States coal mines relative to shafting. Coal mining in the United States is characterized by shallow depths relative to most of the coal mining world. While the trend is toward deeper and deeper mines, many new mines have shaft depth less than 800 feet, and a large number of operating mines are drift or outcrop mines utilizing shafts for ventilation and portals. In the past, shafts of 200-300 feet have been commonly constructed. The use of conventionally sunk shafts at present and in the past is due in part to the shallow shaft length required, favoring conventionally sunk shafts. Another factor is that large shafts are required for multipurpose and production shafts. A third has been the practice of utilizing shaft construction contractors who had been until recently very competitive with raise drilled shafts at shallow to moderate depths. Recently, however, the costs of conventionally sunk shafts have skyrocketed. Too, more shafts are being required. Several factors are responsible among which are: (1) The increasing depth of shaft required for new mines and for shafts in advance of old mines. This significantly affects unit costs, e.g. $/yd3,of conventionally sunk shafts. Moreover, more gas is encountered in the shaft sinking operation.

Jan 1, 1976

By Liu Cheng-si

The number of control plans for placing control devices in a ventilation network is surprisingly large, but the research result indicates that not all control plans are feasible. The feasibility of a ventilation network control plan depends on two factors. One is the influence of the network structure. The structure must contain one independent variable-flow airway in a non-controlled loop. Otherwise, the control plan is unfeasible. The other is the combination of the air resistance, quantity, pressure and other parameters. Under some conditions, the selected values of these parameters may result in an unfeasible plan. As to the influence of the network structure, when the network structure is simple, the feasibility of a control plan can be judged directly. However, for the influence of the parameters, the feasibility of a control plan must be examined through calculation. The control position has been extended into the natural-splitting subnetwork from the conventional constant-flow subnetwork. This technique is theoretically significant. The extension of control positions results in a great increment in control plans and variation in parameters. At present, the calculation methods of the ventilation network control plans are all available. They are quite useful in selecting desirable plans. However, among the plans found, some are impractical or even unfeasible. If the unfeasible ones can be eliminated at first, much time can be saved in design and calculation. This also facilitates management and decision making.

Jan 1, 1991

By L. Max Scott

[INTRODUCTION] The significance of gamma exposure to uranium miners has been recognized only in the last few years. Most ore deposits which have been underground mined, were 1% or less U308. Full-time mining of this grade ore can result in exposure exceeding 1 Rem per year. Several companies in Saskatchewan are planning to mine recently discovered ore bodies which contain ore pods in excess of 10% U308. The purpose of this paper is to present dose data which can be used to estimate gamma exposure from high-grade ore deposits, and to present mining techniques which will minimize miner exposure. [Dose Estimates] When one has a point source of radiation, the conventional laws of isotropic emission and the fall of dose with square of the distance, make dose calculations relatively easy. However, if one has an area source of infinite thickness, the assumption must be made that a uniform gamma flux is being emitted from all faces of the source (Figure 1). Dose from gamma emission would fall off only due to air attenuation up to such a distance at which the source can be considered to be a point source (usually 10 times the largest dimension of the source). For short distances, such as to the cab of ore-moving equipment, the dose reduction would be negligible. Assumptions: 1) Radium and gamma-emitting daughters are in secular equilibrium with uranium. 2) All gamma radiation is emitted from radium and its daughters. 3) Average gamma energy of 0.8 MeV. 4) Uranium ore has a linear attenuation coefficient of 0.212 cm-1, similar to that of Si02(sand). 5) Uranium ore density of 3.0 gm/cm3. 6) One curie of radium emits 6.84 x 1010 photon/sec(l). 7) One percent uranium ore contains 1 x 10-8 Ci/cm3 of radium. 8) Each MeV of 0.8 MeV photon results in a dose of 2.10[ ]10-3 mRem/hr. per MeV/cm2 -sec. 1) 9) Minimum ore depth 100 cm. 10) Linear attenuation coefficient instant for radium gamma of 0.374 cm -1 [ ] The photon flux from a radioactive slab is computed as follows: [Flux = photon/cm3 3(1) 2u S] [where, us is the linear absorption coefficient of s the source (uranium ore).] Thus, 1% uranium ore, in the form of an infinite slab, emits 1613 photon/cm2-sec, which results in a dose rate of 2.71 mRem/hr. Since the dose from an infinite slab is the same as a dose from an infinite radius right circular cylinder, the only correction needed from the above dose rate is for finite radius and point of dose above the end of the cylinder (Figure 2) [Dose = mRem/hr. {E2(bl) - E2(b3) - [(E2(b1sec[E] -E2(b3sec[E]]cos[O](1)]

Jan 1, 1981

By Herbert H. Einstein, Edward C. Tse, David B. Ashley

INTRODUCTION Decision-making in the design and construction of underground facilities must be made under conditions of varying geologic uncertainty, uncertainty which can have a major cost impact if not properly regarded. Of the two approaches for dealing with this variability, preparing for the "worst" anticipated conditions and optimizing design and construction in-situ, preparing for the "worst" conditions is the more if not solely conventionally practiced method in the United States. While the conventional approach is recognized at times to be extremely overconservative, it will remain preferred until a more adaptable method is shown to be economically superior. This paper presents research aimed at providing just such answers as to when and if an adaptable tunnel design and construction approach is more cost effective than a non-adaptable one. To fully understand the characteristics of this choice between adaptable and conventional tunneling alternatives a summary discussion of adaptable methods is presented. An acknowledgement of the importance of geologic and other factor uncertainties in making this decision leads to the adoption of decision analysis as a quantitative methodology for formalizing the problem. Exercising this methodology on three prototypical tunneling scenarios--urban deep, urban shallow, and transmountain--allows an isolation and ranking of the most crucial factors in making the basic approach decision. One scenario, a transmountain highway tunnel, is carried further through a detailed probabilistic analysis to show under what conditions of varying uncertainty adaptable approaches possess economic advantages.

Jan 1, 1979

By Louis W. Cope

Placer material, regardless of the value of gold, tin, titanium, diamonds or other value mineral it contains, remains worthless until the valuable constituent is separated from the bulk of the material. This separation is no mean task when considering that a gold placer containing 0.01 to 0.03 oz/yd3 of gold, which is the range of grade of typical placer deposits; yes, 1:3,000,000! It is a miracle that gold placer mining has ever been profitable. Added to the situation of minute quantities of gold are several other problems, such as the gold often being very finely divided, the association of boulders and clay, and running and/or ground water. As each placer deposit is individual and distinctive, many factors have to be considered in planning the method for gold recovery from the alluvial deposit. Previous chapters have shown that in the exploration and sampling stage, some knowledge of the amount of each size of coarse and fine material which occurs in the deposit as well as the size distribution of the discrete gold particles is determined. Unless informed to the contrary, as a general rule of thumb, plant designers will consider that 40 percent of the material will pass through a 5/8-inch screen or punched plate hole. Also that there may be an occasional nugget and normally considerable amounts of fine gold. The designer must

Jan 1, 1992

In the UK as existing face capacity is replaced, many of the new faces will have higher installed powers and be located in zones of higher strata temperature. These factors coupled with the need to increase production will result in more faces experiencing environmental difficulies, especially with respect to climatic conditions. In many cases these problems are unlikely to be solved, as in the past, by simply increasing the face air quantity. Therefore other techniques including refrigeration will be necessary, possibly requiring major capital and operational expenditure. It is easy to spend large capital sums and incur high operational expenditure without achieving the desired amount of climatic control. There is therefore a great need for reliable prediction techniques to aid in the making of sound, informed decisions which will have a significant influence in the long term on the level of production costs. A computer program able to predict the heat flows and resultant climatic conditions on a long¬wall coalfaces has been developed. Throughout it's development underground measurements have been used to validate the computer model and it has been shown that for an advancing coalface under normal production conditions that the program predicts the climate to within 1°C of the measured conditions. This paper outlines a number of methods available to improve climatic conditions on longwall faces. The coalface temperature prediction program is used to quantify the effects of these methods on the climatic conditions for a model coalface and a comparison is given. In conclusion a cool¬ing strategy for longwall faces is outlined.

Jan 1, 1991

By C. L. Schneider, R. P. King

The ability to predict the liberation spectra that will be produced by a closed-continuous grinding circuit is of fundamental importance for the design, optimization and control of most operations in an ore dressing plant. The only known approach through which such a calculation can be performed is the population-balance-model equation. The latest, and certainly most significant, advance made in this area is the solution proposed by King (1990), which requires one textural parameter measured directly from the ore being studied. The main advantage of King's solution is that, unlike the conventional solutions, it does not require the estimation of hundreds of arbitrary parameters that cannot be independently measured. However, King's solution relies heavily on a knowledge of the detailed internal structure of the Andrews-Mika diagram (Andrews and Mika, 1975), which has never been measured for any ore. The characterization of the internal structure if the Andrews-Mika diagram requires the measurement of the liberation spectra at several progeny sizes produced by the breakage of monosize-monograde particles at several different grades. In this paper, a procedure based on magnetic fluid fractionation for generating seven narrow-size, narrow-grade samples is presented. Each of these samples was then broken into six progeny size classes in an ultrasonic mill. The one- dimensional liberation spectra of each of the 42 progeny and seven parent particle samples were then measured by image analysis. The measured linear-grade distributions are presented in this paper. The calculation of the correspondent volumetric-grade distributions is discussed.

Jan 1, 1995

By P. Sanchez-Mejorada

Quimica del Rey, SA, a subsidiary of Industrias Peñoles, SA de CV, produces sodium sulfate from brines extracted from a playa of Laguna del Rey, located in the State of Coahuila in northern Mexico. The spent brine is used as raw material for the production of magnesium oxide. The brine, which contains ions of sodium, magnesium, sulfate, and chlorine, occurs filling intercrystalline voids of a lenticular evaporite deposit whose main constituents are glauberite (sodium-calcium sulfate) and blöedite (sodium-magnesium sulfate).

Jan 1, 1987

By W. Burger

For the development of deep hard rock mines fast access to the orebody is critical. In some cases the mineralized area is more than 1500 m (5000 ft) below surface. Excavation of shafts or declines is typically on the critical path of the project schedule. Saving time on those activities can significantly increase the net present value of the mining project. Mechanical excavation methods are a step-change in excavation performance and labor safety compared to drill and blast operations. In hard rock conditions roadheaders can not be used effectively, so disc cutting is the first choice. For excavation of declines tunnel boring machines (TBM) can be used in many cases. These provide in certain rock conditions considerably higher production rates compared to drill and blast excavation.

Jan 1, 2010

By N. T. Rempe

The underground voids that result from mining provide opportunities for deep geologic waste disposal (DGWD). Such disposal could solve many environmental problems. DGWD takes careful planning, technology transfer and true partnership between waste generators and mine/repository operators. The US government is now planning on using specially mined excavations to dispose of radiotoxic and mixed waste. Using the experience gained from the domestic projects that are now in preparation and from foreign repositories that are now in operation, US mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1998

By F. F. Aplan, V. Choudhry

This investigation is an exploratory study to evaluate a large number of potential pyrite depressants for use during coal flotation. Subsequently, the more promising reagents can be evaluated in detail. Several reagent categories (such as alkalis, lime, oxidizing agents, reducing agents, specific inorganic ions and dispersants) that were found to be effective pyrite depressants are discussed here. Other pyrite depressants will be discussed in Parts II and III.

Jan 1, 1993

By Giuseppe Bonifazi

This study examines the problems involved with the control of characteristics of the products resulting from comminution operations. A methodology of investigation based on texture analysis procedures by image processing techniques of the comminution product is proposed. Some examples of applications are considered with particular reference to comminution products of different textural, structural and mechanical characteristics. The advantages and the limites of this method of approach are, indicated, both as regards performance of the investigations and subsequent processing of results.

Jan 1, 1989

By Hidehiko Nakazaki, Sakuro Murayama, Mitsuo Miura, Masaaki Endo, Yoshiaki Hurukawa

This is a detailed report of construction experience of a tunnel built by a shield of rectangular cross section with reinforced concrete segments. In case of tunneling by a rectangular shield, there were the following problems to be overcom by technical developments; (1) structural joints between segments, (2) complexity in erector handling, (3) exact steering operation of shield and perfect filling of tail void left around the lining erected. Such rectangular shape of cross section has various advantages comparing the conventional circular shape as follows; (1) effective utilization of excavated space, (2) greater overburden depth, (3) stability of lining against unbalanced earth pressure caused by neighbouring construction.

Jan 1, 1979

By L. Laage, R. Greur, W. Pomroy

MFIRE is a mine ventilation and fire interaction computer simulation program. It allows transient state ventilation simulation and features mass based flow rates, natural ventilation, air recirculation, fan curve fitting, airflow reversal and product of combustion tracking. MFIRE was designed to accommodate the needs of the mining industry, for routine ventilation calculations and mine emergency planning. This paper describes recent work by the US Bureau of Mines and Michigan Technological University to improve MFIRE by incorporating humidity in the mass flow and heat exchange calculations, a data file preparation program, and variable reference density in the network calculations. Recent bug fixes are also discussed.

Jan 1, 1995

By K. Y. Haramy, B. T. Brady

A scale-invariant theory of the strength and deformability, of rock masses in static equilibrium and at incipient failure is proposed The theory provides a rationale, for designing structures in rock. This paper presents results of experiments conducted by the US Bureau of Mines and presents theoretical methods to determine and interpret the in situ strength of rock masses using the borehole shear tester.

Jan 1, 1996

By W. Douglas Gould, Mei-Lin K. Stichbury, Jeffrey G. Bain, Blowes David W.

The mechanisms of release of arsenic in gold mine tailings were investigated. The highest concentration of dissolved As (75 mg/L) was observed near the base of the tailings impoundment, in close association with a peat layer. Elevated concentrations of reduced iron and hydrogen sulfide were also measured at the base of the impoundment. High numbers of iron-reducing and sulfate-reducing bacteria were detected at depths within the impoundment which correlated with dissolved As, Fe and H2S. The data presented in this paper suggest that arsenic is released from the tailings by bacterially-mediated reductive dissolution of As-bearing iron minerals.

Jan 1, 2000

By Andrew J. Neale, Mark Franklin, Mike Cooper

Although recent advances have significantly improved our understanding of flotation fundamentals, disturbance variables combine to make it difficult to maintain steady state operating conditions over either the short or long term. One of the major concerns relates to knowing how much reagent to add to the flotation system, how to monitor the addition rate, and how to determine when to adjust the reagent addition rate in the presence of these disturbances. This paper will look at the development and installation of process control systems that address these issues. The economic benefits that accrued from the implementation of these strategies is described.

Jan 1, 1994