Search Documents

By K. Hansson, A. Jedborn

Background In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore, from a system's point of view, slurry transporta¬tion would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alterna¬tive examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasi¬biliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. l . The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then tempo¬rarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situ¬ations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe¬line, and personnel are needed. In a first phase (Fig. 2), a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1989

By Richard M. Crowell, Laurie M. Tahija, Keith D. Dagel

Echo Bay Mines Ltd. operates a gold heap leach in Round Mountain, Nevada, U.S.A. In the past two years, the mine has expanded operations from 13.5 kt/d (15 kst/d) to 41.0 kt/d (45 kst/d), making it the world's largest gold heap leach operation. The expansion is a separate system from the previous 12 year old plant, yet very similar. The flowsheet contains open circuit primary, secondary, and tertiary crushing with interstage screening. A leach pad stacker loads reusable asphalt leach pads. The process plant features carbon adsorption, pressure strip, electrowinning, and electrorefining.

Jan 1, 1990

By N. Edmonson

Frasch sulfur production/pricing decisions are based on market demand, less nondiscretionary sulfur supply. Price covers the cost of Frasch production and byproduct sellers accept the Frasch price structure. Large stocks have led Canadian byproduct producers to price aggressively at times, but their near-term drawdown suggests more passive price policies in the 1990s. Expanding continental nondiscretionary supply is combining with sizable Frasch supply increments to weaken prices. Simulations using a market model embodying these structural characteristics indicate that expanding demand may not result in substantial recovery from 1992 price lows before 1996.

Jan 1, 1995

By Anders Sellgren, K. Hansson, A. Jedborn

In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore. from a system's point of view, slurry transportation would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alternative examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasibiliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. 1. The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then temporarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe- line, and personnel are needed. In a first phase (Fig. 2). a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1990

By Y. C. Kim

This paper describes the implementational aspects of a blast hole kriging system that has been developedfor the purpose of daily ore/waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore/waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBMIPC AT or XT computers, using the Fortran language and supplemented by a few assembly language routines for the bit- map manipulation. This paper emphasizes the practical implementation requirements of the system and discusses system design considerations.

Jan 1, 1991

By John Turney, John Gathje, Donald Gale

The Eskay Creek deposit, located in northern British Columbia, is a high-grade gold/silver ore associated with complex polymetallic sulfides. Process development began in 1989 and continued through 1993. Because of the refractory nature of the ore, options including roasting and smelting were investigated. The selected process of pressure oxidation was the basis for basic engineering design until a re-evaluation of economics and risk indicated a preference for toll smelting. Although well proven in many industrial applications, pressure oxidation of the Eskay Creek ore dictated several innovations to solve problems associated with silver jarosite formation, preg-robbing, and high soluble copper and zinc concentrations.

Jan 1, 1995

By Jan K. Wolski

The PC computer program PCVENT, version 3.3, for the ventilation network analysis now incorporates a real-time fire simulator. Position of the fire or a source of contamination and the character of the event are input from the keyboard. There are several options of type of fire: heat only, contaminant only, or both with a constant burning rate or with oxygen as the only limiting factor. Airway resistances or fan characteristics can be modified during a fire simulation. This allows testing of various fire suppression strategies. Program application in the analysis of a real mine fire is presented.

Jan 1, 1991

By Prasannarao Dontula, Kal V. S. Sastry

Advances are made in the field of mineral processing on a continuing basis both in the industry and the academia. These advances do not always get used fully because of the inherent difficulties in the transfer of knowledge and reduction to practice. In recent years, knowledge engineering is being increasingly employed in other fields to overcome some of these difficulties. This paper presents a vision of how knowledge engineering can be applied to the benefit of the mineral processing industry and includes a discussion of associated principles, techniques, and advantages.

Jan 1, 1993

By K. L. Branham, D. W. Steeples

Surface collapse over abandoned sub- surface coal mines continues to be a problem in many parts of the world. High-resolution P-wave reflection seismology was successfully used to locate water-filled cavities in a 1-m (3-ft) thick coal seam at depths of 9 m (29 ft) in southeastern Kansas. A dominant frequency of 275 Hz was attained enabling us to delineate the top of the coal seam. To our knowledge, this study is one of the first to locate water-filled coal mine cavities at depths of less than 30 m (100 ft) wing high-resolution P-wave seismic reflection techniques.

Jan 1, 1987

By K. E. Kolm, W. H. Langer

Developing natural aggregate resources (sand, gravel and stone) creates environmental impacts. A systems analysis method was designed to characterize the components of the environmental system, identify potential impacts to those systems and evaluate the extent of those impacts. The stepwise method consists of problem definition, data collection, preliminary conceptualization and characterization, additional data collection, data analysis and refinement. The method requires analyzes of various systems making up the environment, including land surface, geomorphic, subsurface and groundwater systems. After system characterization is complete, the method focuses on identifying and evaluating potential environmental impacts to determine acceptable mining strategies.

Jan 1, 2003

Diesel engines are used in underground mining 1 throughout the world. Exhaust gases from those engines contain toxic components. To protect quality in underground mines, diesel emission control was introduced decades ago, many years before the first surface applications. Today, emission controls, such as catalytic converters, are standard on underground diesel engines in countries concerned with occupational safety and health. Nett Technologies manufactures a range of diesel emission-control devices for underground mining. Emission problems are not the same at each mining operation. And there is no universal control technology. The selection of exhaust aftertreatment technology depends on raw exhaust emissions, particular emission problems, fuel quality and economics. Some of the technologies that have been used in underground mining to control diesel emissions include catalytic converters, diesel filters, fume diluters and water scrubbers. Table 1 compares the effectiveness of these technologies to control the particular components or aspects of diesel emissions.

Jan 1, 1997

By J. Mark Richardson

Steady-state flowsheet simulators for mineral processing plants have evolved to a current high level of utility and accuracy. Reliable, general-purpose, semi-empirical models now exist in nearly all unit operations categories particularly in the areas of comminution and classification. .These models, installed as user-selectable functions within the integrated frame- work of flowsheet balance-solver software systems, can be strung together to represent any plant configuration. In addition, CAD-like graphics, data reconciliation and model parameterization functions have become standard features of the current generation of integrated plant simulators. These advances have given engineers the capability to investigate many different plant scenarios while requiring a minimum of actual plant testwork. This paper describes a methodology and an integrated software package which are being successfully applied in a number of operating plants worldwide to predict plant performance under changing conditions. Those conditions which can be changed include effect-of ore type, feed size, water addition rates, equipment geometries and flowsheet modifications. By using data from actual plant optimization exercises in real mills, the paper illustrates and out- lines a technique which includes plant data collection, ore breakage testing, flowsheet simulation, model-fitting (parameterization), data adjustment and model experimentation. Brief descriptions of some unit operations models, such as autogenous mills and cyclones, are provided as examples of the current state of such models. Ore breakage testing and its relation to certain models is also discussed. Computer- generated size-distribution graphs, along with tabular data generated by the simulator, round out the presentation and serve to demonstrate the real- ism and accuracy of the models. The paper concludes with a partial list of cases where this technology has been successfully applied.

Jan 1, 1992

By Wallace Jarman

Introduction As with many gravity concentration processes, pneumatic concen¬tration traces its origin in antiquity. The use of winnowing to separate chaff from grain has long been known, and such procedures were undoubtedly practiced in ancient civilizations for the concentration of ores and the separation of slag from metal whenever specific gravity, size, and shape differences were favorable. Taggart142 has reported on the use of dry rockers and dry panning techniques for use with gold ores in arid regions such as Western Australia. The present day air table was developed in the last century for this purpose. Devices and Processes Classification. All classifiers make a separation on the basis of size, shape, and specific gravity. In addition to specific gravity and size, particle shape factor is often particularly important to pneumatic processes, and advantage is taken of the fact that both flat and fibrous particles settle at velocities substantially lower than that of their equiv¬alent spheres. Another factor of importance in this process is the bulk density of the material since substances such as exfoliated ver¬miculite or partially opened fibrils of asbestos have bulk densities significantly lower than those of the pure in situ mineral. Winnowing takes advantage of all of these physical factors to affect a separation starting with a closely sized feed, and vermiculite has been separated from rock by this process.142 When air classifiers are used to size minerals, the separation will often not be perfect because heavy particles will respond similarly to somewhat coarser light particles while flat, elongated, and low bulk density particles will act as would particles finer than the cut size. An example of a classification process that also results in concentration is the zig-zag classifier"' used to separate paper from glass, metal bottles, and cans during the recycle of municipal solid waste. Application of this process to minerals showing the proper specific gravity, size, and shape differ¬ences is obvious. An important device of this type is an air-aspirated screen used to remove asbestos from its associated rock during the dry processing of that mineral.144 The raw ore is crushed and screened and the asbes¬tos removed by aspiration from the surface of the screen by virtue of its shape and low bulk density. Hindered Settling. Based on the discussion in the section on "Hindered Settling Concentration and Jigging," the use of air devices could be anticipated in desert areas or where moisture may be deleteri¬ous to the product to be separated. Such processes have three major defects: (1) dust may be difficult to contain, (2) fines are difficult to process, and (3) the process is inherently less efficient than are wet processes as may be seen from Eqs. 3 and 4 in the section on "Hindered Settling Concentration and Jigging p. 4-47." Taggart142 has reported on the use of both dry panning and a dry rocker for gold separation in and regions. The dry panning makes use of winnowing, defection on the basis of specific gravity and shape during fall, and hindered settling. Prescreened placer material is poured from one pan to another as air blows across the falling stream. The process is repeated many times with hand picking to produce a rough concentrate. Magnetic minerals are then removed, and the residue, one grain deep in the pan, is air blown. In dry rocking the gravel is sized on a steeply inclined screen with the undersize fed to a riffle box with a porous bottom which is blown from underneath."' This device was the forerunner of the present-day air table. Air Tables and Jigs.145. 146 At least nine types of these devices have been developed, all but two of them for coal. While the devices used for coal may be characterized as pneumatic jigs, pneumatic tables, and pneumatic landers,145 only pneumatic jigs survive today. The same is true for ores.'" In these devices presized particles are fed to the separator which consists of an inclined vibrating conveyor with a porous surface through which air is carefully introduced to form a fluid bed. The lighter particles are lifted by the air out of uphill conveyance and float downhill, while the heavier particles in contact with the surface are conveyed uphill by the vibrator. Typically both transverse and longitudinal slopes are used. A plan view of a Triple S air table and the type of separation made is shown in Fig. 44.147 Because of its external appearance, the device has been called an air table, although it functions essentially as a jig. However, some of the asymetrical acceleration conveying function of a standard shak¬ing table is also performed by the eccentric vibrator incorporated into this device. Low pressure air is admitted below the vibrating table surface consisting of cloth (e.g., canvas), porous plastic, woven wire, or punched metal supported on a wire mesh or grid. As with a shaking table, the device produces a concentrate, middlings, and tailings. The middlings are recycled or are subsequently treated on another concentrating device. As with many wet separations, presizing by screening is necessary. The oft-repeated admonition of Professor Richards, "Separation without classification is damnation," is cer¬tainly true here. In this way a small heavy particle which might weigh the same as a large light particle and thus report to the same place on the air table has already been removed in the sizing step. Air tables are almost universally encased with a canopy to remove dust by aspiration. Some concentration may also be achieved in this step when favorable specific gravity, size, and shape differences are present. Applications Ore Separations. Air tables were originally developed for ore separations, and they find application in and regions or where water is deleterious or inconvenient to use or remove (e.g., small tonnage materials already dried). They have been used for asbestos, bauxite, calcite, cassiterite, columbite-tentalite, diatomaceous earth, fluorite, gilsonite, graphite, kyanite, manganese minerals, mica, managite, perlite, pyrite, pyrrhotite, vermiculite, and uraninite ores. More recently, air tables have found favor in separating a wide variety of secondary materials such as abrasive grains, bone char, catalysts, fiberglass, scrap glass, scrap wire from its insulation, prills from slag, dross and coke from metal or from each other, metal from crushed crucibles, lead from plastic in old batteries, and cubic particles from flat ones. The devices also finds considerable application in the preparation of food¬stuffs. As stated before close sizing before separation is desirable, and if the specific gravity difference is slight, very tight

Jan 1, 1985

By E. Steel, V. S. Znamensky, A. Wylie

The asbestiform habit is most commonly developed in certain amphiboles and chrysotile, but other minerals also may crystallize with this unusual habit. The habit may be characterized by (1) a fibril structure, single or twinned crystals of very small widths (generally less than 0.5 pm), which have grown with a common fiber axis direction, but are disoriented in the other crystallographic directions; (2) anomalous optical properties, primarily parallel extinction; (3) unusual tensile strength; (4) high aspect ratio; and (51 flexibility. In addition, there is evidence to indicate that some amphibole asbestos may have unusual surface properties. ASBESTOS AND THE ASBESTIFORM HABIT Asbestos is defined as a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven, are heat resistant and chemically inert, and possess a high electric insulation, and therefore are suitable for uses where in- combustible, nonconducting, or chemically resistant material is required (Gary, et al., 1974). The most common minerals that may occur with the asbestiform habit are chrysotile, grunerite (amosite], riebeckite (crocidolite), actinolite, anthophyllite, and tremolite; although the development of this habit among these minerals is rare. Other minerals, most notably other amphiboles, can occur in this habit, but no others have been mined commercially as asbestos. All asbestos is confined to metamorphic rocks, even though other habits of the amphiboles are common in igneous rocks. Slip fiber veins are the most common deposits (South African amosite, Canadian chrysotile, etc.), but mass fiber deposits also may occur such as California chrysotile or mountain leather. Field relations and experimental data support the hypothesis that metasomatism is the dominant process in the formation of asbestos fibers, amphibole as well as serpentine. The crystal habit of a mineral is the shape or form a crystal or aggregate of crystals take on during crystallization. The asbestiform habit has a number of characteristics that differentiate it from other habits. Chief among these is the fibril structure.Afibri1 is a single or twinned crystal with a very small width, generally less than 0.5 pm, and an extremely high aspect ratio; bundles of fibrils may have lengths reaching into the cm. Fibrils share a common crystal growth direction along the long axis of the fiber, but appear to be disoriented with respect to one another in the other crystallographic directions. The structure of the individual fibrils, and the organization of fibrils within a fiber may differ among the various types of asbestos. The fibril structure of asbestos is probably a factor in controlling a number of secondary properties that include high tensile strength, flexibility sufficient for weaving, and anomalous optical properties. The high tensile strength of asbestos is quite remarkable, exceeding that of the ordinary varieties by a thousand fold (Zoltai, 1978). In part, this may be attributed to the lack of defect on the fibril surfaces (Zoltai, 19781, but some contribution also must come from the existance of bundles and the nature of the ordering of and forces among the fibrils. The flexibility is not only enhanced by the fact that the fibrils may slip past one another, but by their small widths and extreme aspect ratios. However, structural defects parallel to the fiber axis also may contribute to this property. Among the common commercial asbestos types, the greatest flexibility is found in chrysotile and the least in grunerite asbestos (amosite), varying inversely with fibril thick- ness. In addition, at least for chrysotile, composition also may affect the flexibility of the fibers. Finally, most asbestos minerals are mono- clinic, but optically display parallel extinction (Heinrich, 1965, and Wylie, 1978). This also must be due, in part, to the ordering or lack of ordering of the fibrils. The fibril structure is probably a random

Jan 1, 1986

By Julian Boldy

The discovery of the Delbridge massive sulfide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage haloas a lithochemical pathfinder to blind ore, coupled to its location relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy. Systematic sampling of microfractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulfide deposit was subsequently found to be blind and topped at the 107-m (350-ft) level. This case history is presented in the context of its time and was the first volcanogenic ore deposit to be discovered utilizing mercury as a pathfinder in the Canadian Precambrian. The case history also illustrates that the practical application of an innovative technique coupled to a new geological interpretation can result in success, even on a property that was centrally located in a mining district and had undergone intensive exploration efforts over a 38-year period.

Jan 1, 1991

By Shibo Zheng, Zhengxing Gu, Zhizhong Gao

In recent years, beneficiation tests were conducted on high dolomite phosphate samples from Florida by the authors from China Lianyungang Design and Research Institute (CLDRI). The research results indicated that flotation is the most effective process for recovering phosphate from Florida high dolomitic pebble. Other operations like scrubbing, desliming and selective grinding might work to some extent, but they could only be applied as supplementary approaches in some cases. Heavy media separation and calcination-digestion technologies are hard to produce satisfactory performance. This paper presents the results of both lab scale and pilot plant tests on Florida high dolomite phosphate pebble using the fine particle flotation technology developed by CLDRI. Some discussions are made on the concerns of Florida phosphate industry and further research.

Jan 1, 2002

By Fred N. Kissell

INTRODUCTION During the last few years, several new ventilation developments have attracted the interest of mining engi¬neers. Some of these developments are applicable pri¬marily to hard-rock mining, while others are more applicable to coal mining. STOPPINGS Parachute Stopping The parachute stopping is a new type of quick-erect stopping that is intended for temporary use in hard-rock mines (Kissell, Thimons, and Vinson, 1975). As shown in Fig. 1, the stopping is shaped very much like an ordinary parachute, with a canopy of impermeable fabric that is sewn to regularly spaced straps running to a common point. To erect the stopping, the straps are attached to a fixed anchor point such as a roof bolt, and the edge of the canopy is lifted into the moving air¬stream. The airstream pops the parachute canopy into place, and the differential air pressure across the stop¬ping holds it in place, forcing the fabric against the walls, roof, and floor of the mine opening. The principal advantage of the parachute stopping is that it requires only a few minutes to install, making it a great time-saver for emergency use or for day-to¬day changes in ventilation during the production cycle. However, the parachute stopping does require some minimum air velocity to lift it and some minimum differential pressure to hold it in place. For a fabric weighing 0.27 kg/ m2 (8.0 oz per sq yd), the minimum air velocity is about 0.5 m/s (100 fpm), and the mini¬mum differential pressure is about 0.05 kPa [0.2 in. water gage (WG) ]. There is always some air leakage around the stop¬ping, mainly depending upon the extent to which pipes or other obstructions encumber the airway and prevent good sealing. Leakage of a few cubic meters per second (a few thousand cubic feet per minute) can be expected, unless foam is used to improve the seal at the edges of the canopy. Quick-Fix Blowout Stopping The quick-fix blowout stopping is a variation of the parachute stopping (Thimons and Kissell, 1976), and it is used in the proximity of blasting operations. This type of stopping is designed to be blown out easily by the blast forces, and it may be reinstalled quickly and easily. The long high-strength straps of the parachute stopping are replaced by groups of short straps that tear easily. These straps are attached at six equally spaced locations around the perimeter of the canopy. To erect the stopping, one strap of each of the six groups is fastened to the mine wall, roof, and floor by using spads, by setting pins with a powder-actuated gun, or by tying the straps to some firm anchor point. Once the straps have been attached, the differential air pressure across the stopping, which must be at least 0.025 kPa (0.1 in. WG), forces the stopping perimeter against the mine walls, thus creating the air seal. It is the self-sealing feature of this stopping that makes it a significant time-saver. Only a few attachment points are needed; in many cases, four attachment points are sufficient, since the stopping naturally tends to form a seal with the airway surfaces. When nearby produc¬tion blasting exerts excessive forces on the stopping, one or more of the straps tears away from its attachment point, protecting the stronger canopy from damage. Damage-Resistant Brattice The damage-resistant brattice is a stopping that is designed for use in mines such as salt and limestone mines where the differential pressures are low and the roof is relatively flat. As shown in Fig. 2, the damage-resistant brattice consists of a series of brattice panels that are hung vertically and joined by Velcro® connections. When the brattice is subjected to strong blast forces, the Velcro® connection peels apart and allows the panels to open without incurring damage. The Velcro® connections can be resealed by hand within a matter of minutes. Such damage-resistant brattices have withstood the blast effects of 318 kg (700 lb) of ammonium nitrate-fuel oil (ANFO) explosive detonated as close as 91 m (300 ft) from the brattice. Ordinary brattice cloth is used for the panels, with a 51-mm (2-in.) wide strip of Velcro® hooks sewn along one edge of the length, and a 51-mm (2-in.) wide strip of Velcro® pile sewn along the other edge. Both the hooks and the pile are sewn onto the same side of the brattice cloth. The resulting Velcro® seal formed be¬tween adjacent panels is perpendicular to the brattice itself, and the leading edge of the seal can be directed either toward or away from the blast forces; the brattice works equally well in either case. To hang the brattice, panels of brattice cloth about 0.9 m (3 ft) longer than the height of the airway are cut from a 1.8-m (6-ft) wide roll. The additional 0.9 m (3 ft) of brattice cloth allows 0.3 m (1 ft) for attachment to the roof by means of a board, with 0.6 m (2 ft) for forming a good air seal at the floor. Each brattice panel is wrapped once or twice around a 51 X 102 mm (2 X 4 in.) or 25 X 76 mm (1 X 3 in.) mounting board that is 254 to 305 mm (10 to 12 in.) shorter than the width of the panel. For convenience in

Jan 1, 1982

By Kenneth N. Han, Jianshe Liu

Various techniques used in the removal of metal ions from effluent streams have been reviewed. These techniques include recovery of metals by biological treatment, chelating agents, adsorption, ion- exchange and chemical precipitation. The main thrust of this paper however, is concerned with the removal of cadmium and zinc ions from the solution by adsorption utilizing liquid fluidized beds. The bed particles used were silica of 150x200 mesh. The range of the concentration of these ions studied was 10-3 to 10-5 M. Important variables examined included flow rate, concentration of metal ions and amount of bed particles. A mathematical model describing the concentration profile of metal ions in the axial direction in liquid fluidized beds has been developed. The equation of continuity was solved numerically and the results were used to predict the recovery of metal ions in fluidized beds.

Jan 1, 1992

By E. R. Braer, C. J. Bise

The trend in underground room-and-pillar coal mining is to employ remote-controlled, continuous-mining machines and extended cuts to depths of 12 m (40 ft) or more. This system of coal extraction, adopted by more than 435 mines, can create additional worker safety hazards. To address the ground-control-related safety hazards, a combination of statistical analysis and numerical modeling was used. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the coal mine roof rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling was completed to predict roof displacements during extended-cut mining. This paper describes the results of these studies and their impacts on the safety of extended-cut mining.

Jan 1, 2000

By H. O. Seigel, John C. Robbins

Luminex is a new method of prospecting for mineral deposits based on time-resolved mineral luminescence created by an ultra-violet light source. Developed by Scintrex Ltd., Luminex detects and resolves a group of key minerals - either ore minerals themselves or, more often, accessory or pathfinder minerals for certain types of economic ore deposits. These minerals are commonly found on the earth's surface, even in areas of considerable weathering. The method extends the range of mineral deposits that are remotely detectable from the air. Tungsten, tin, molybdenum, gold, and bedded lead-zinc deposits are included. Therefore, Luminex is a natural supplement to the three classical methods of airborne geophysics. The luminescence of minerals has been known and used qualitatively in mineral exploration for many years. But there are more than 500 minerals known to be at least sometimes luminescent. Luminescence of most is unpredictable and the colors they emit may vary from locale to locale. It is, perhaps, this apparent complexity of the field that has discouraged its proper scientific scale until now. There are two basic types of luminescent minerals - intrinsic and impurity activated. In the first type, luminescence is an inherent property of the mineral in its purest form. In the latter, luminescence is due to the introduction of foreign trace elements, often in very modest amounts (ppm), into the crystal lattice. These trace elements are known as activators. There are very few intrinsic luminescent minerals commonly found in nature. Chief among these are the calcium tungstatemolybdate family, more commonly known as the scheelite-powellite family, and the uranyl minerals such as autunite and saleeite. The vast majority of other known fluorescent minerals such as fluorite, hydrozincite, and many calcites, are impurity activated - that is, they will not fluoresce in purest form. In addition to the many minerals likely to luminesce at the earth's surface under ultraviolet excitation, any prospector who has ventured out at night with a mercury lamp will know that much organic matter luminesces - for example lichens and even scorpions. Just as the eye finds difficulty in resolving the luminescence of minerals from that of organic materials, it also has its limitations at sorting out minerals from one another by their luminescent colors. Figure 1 shows, in part, the photoluminescent emission spectra of scheelite, hydrozincite, and autunite. It is clear that there is a considerable similarity in spectrum between scheelite and hydrozincite and a great deal of overlap. In fact, a small amount of molybdenum in the scheelite lattice can almost bring these two spectra into coincidence. On the other hand, the autunite emission spectrum is clearly resolved from the other two. Basis of the Method The right-hand side of Fig. 1 shows the time waveforms of decay of the photoluminescence of the same three minerals. It is apparent that the lifetimes of photoluminescence of scheelite and hydrozincite are radically different and that these two minerals, therefore, may be readily resolved through their emission lifetime characteristics. It is in the realm of time-resolved measurements (lifetime characteristics) that Scintrex has made its major advance in the Luminex method. With the exception of some work by Exxon confined to uranyl minerals, to the best of our knowledge, no systematic scientific investigation has been carried out in the field of time-resolved mineral luminescence studies other than the work of Scintrex. Scintrex's findings are that all organic materials and most commonly activated luminescent minerals have lifetimes shorter than one microsecond. In addition, only a relatively small number of minerals - among them those called key minerals, or certain ore and pathfinder minerals - have lifetimes greater than one micro-second. Scintrex is able to characterize these minerals primarily by their emission lifetimes and secondarily by their emission spectral characteristics. By a combination of these factors a mineral index is arrived at. From that, photoluminescent minerals can be resolved from one another with a high degree of probability. At least two spectral channels and two time channels - of which one can be common - are required to apply this mineral index. Ground System A portable hand-held Luminex analyzer based on a modulated mercury lamp has been used to date in Canada, the US, and Australia. The current production model of this device is the LG-2. It has two spectral channels and two time channels for each spectral channel. Figure 2 shows a ground Luminex traverse over the Texas-Arizona zinc prospect in Arizona. The instrument was set so the channel read was hydrozincite-specific insofar as possible. The mineralization in this prospect is known to be hydrozincite and other zinc secondary minerals in limestone. Figure 3 shows a ground Luminex traverse over the AAA uranium prospect in Nevada. The instrument was set to optimize the uranyl response. For comparative purposes, broadband scintillation counter readings were made on the same stations (also shown in Fig. 3). It is apparent that both the Luminex and the scintillation counter results reflect a near-surface distribution of uranyl minerals. It is interesting that no visible uranyl secondary minerals

Jan 7, 1983