Search Documents

By K. Biswas, H. C. Lee, S. J. Jung

Ore passes are circular openings excavated in rock for in-mine gravity-transportation of ore. It is a very important component of the overall load-haul system of an underground mine. The function of an ore pass is two-fold: first, gravity-transportation of ore from the extraction level to the haulage level and second, the loading operation at the haulage level utilizing the gate assembly. In reality, like any other system component, an ore pass breaks down either due to a hang-up within the ore pass or due to a failure in the gate structure. The failure of the gate assembly may be attributed to a greater extent to the impact load as experienced by the components of a gate structure as a result of the direct impacts of the rock fragments and to a lesser extent to the static or 'dead weight' loads of the accumulated materials in the ore pass. This paper uses simulations in Working Model® as an aid to investigate the effect of both the impact and static loading on the gate assembly and on the inner-walls of the ore pass. The paper also investigates the impact of ore pass inclination and the presence or absence of dogleg on the static and impact loading of the same.

Jan 1, 2002

By P. D. Roa, O. Noirot, H. Owens, D. E. Walsh, J. R. Mokka

Over a period of eight years (1989 through 1997) the Mineral Industry Research Laboratory (MIRL) at the University of Alaska, Fairbanks, AK, has investigated the effects of temperature, residence time and particle size on the degree of low-rank coal (LRC) upgrading for a nonevaporative, hydrothermal drying process, also known as hot water drying (HWD). The following three Alaskan LRCs were used in this study: Usibelli coal (Seam No. 4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10 to 20 min of residence time. Thereafter, the upgrading process slows down, and more than 100 min of additional residence time is required to produce percentage increases equivalent to what was achieved in the first 10 to 20 min. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove gindabilities all appear to change linearly with temperature within the 275°C to 325°C (525°F to 61 5 OF) range.

Jan 1, 2000

By T. J. Cox

The Red River is located within the Sangre De Cristo Mountain Range in northern New Mexico. An approximate 12-mile segment of the river from the town of Red River to the village of Questa (Questa) includes several hydrothermal alteration zones. Alteration ?scars? formed as a result of rapid chemical weathering and physical erosion of pyrite-rich hydrothermally altered rocks. Storm water runoff from the scar drainages contributes metal-laden, acidic water to the river and creates a visible plume of discolored water in the river. Acidic runoff reduces the river pH from 7 to the mid 3s for at least 2 hours during large storms and the low pH water continues downstream. Runoff from scar drainages increases some metal concentrations in the river from below chronic ecological criteria to as much as two orders of magnitude greater than acute ecological criteria, and results in acutely toxic conditions for macro-invertebrates. A general improvement in the river?s water quality occurs downstream due to dilution from tributary inflow from non-mineralized watersheds, the natural buffering capacity of the river, and storm water controls at the Chevron Mining Inc. Questa mine.

Jan 1, 2011

By A. Cordonnier, Ch. Obry, R. Evrard

In spite of the large annual expenditures and the vast field of activity covered, it cannot be said that many new grinding machines have actually come to light and modified the existing market for more than half a century. Manufacturers have mainly made advances in increasing machine sizes, efficiency and reliability, and in machine automation. The relatively recent emergence of roller presses is the only exception to this homogenisation of machine ranges. The development of roller presses in pregrinding has shown the advantages of compression grinding over the ball mill from the power consumption point of view. But classical roller presses still have maintenance problems due to the high grinding pressure. The FCB Research Centre has carried out much work in this field and in particular has studied the advantages of this process in pregrinding and integral grinding. These researches lead to the development of two new compression grinding machines. The first one, HOROMILL®, presented for the first time on the 8th European symposium on comminution at Stockholm, finds its application in the field of fine to very fine grinding in dry process. The second one, RHODAX®, presented at INTERMAT in Paris, covers the field of secondary and tertiary crushing and the first stage of grinding for most of the minerals in dry or wet process. Its high reduction factor permits to do with only one machine the work realised today with two or three crushing/milling stages. These two complementary machines offer a wide range of combination summarised on [Figure 1].

Jan 1, 1995

By S. A. Kupferman

Cement raw materials used in southern California and Arizona cement plants occur in a wide variety of geologic environments. Limestone, the primary material making up 75-80% of the raw materials mix used in cement manufacture, is mined solely from Paleozoic Era deposits. During this time, 570-245 million years ago, vastly more limestone was formed in California and Arizona than at any other time (continent was in southern latitudes). The general geology of each limestone deposit associated with the eight southern California and two Arizona cement plants will be reviewed. Many of these deposits are geologically complex, having been subjected to Mesozoic deformation, metamorphism and instrusive events, along with Cenozoic uplift and deformation. All of the cement plants in this region require the use of secondary additives in order to meet the chemical requirements for cement. The kinds of additives vary greatly, depending upon the chemistry of the limestone deposit, cement specifications, and the cement manufacturing process. In some cases, clay deposits with suitable chemistry on or near the limestone sources are utilized. Where alkali limitations or need for alumina-rich materials exist, then specialty clay deposits are used. Iron-rich sources in the region include iron ore deposits and slag or mill scale from local steel mills. The geologic setting and location of these additives, along with gypsum and silica-rich deposits presently in use, will be mentioned.

Jan 1, 1987

By W. S. Versluis, G. W. R. Kuzyk

Atomic Energy of Canada, Ltd. (AECL) is constructing an Underground Research Laboratory (URL), a major component of-the Canadian Nuclear Fuel Waste Management Program. In July 1988. AECL and the US Department of Energy commenced a cooperative research program that included extending the URL shaft by 190 m (623 ft) to the 443-m (1,453 ft) depth. The shaft extension, 4.6-m- diam (15-ft-diam), was excavated by full-face blasting using a burn cut. A Galloway stage accommodated the research activities and the sinking contractor's requirements. Blast designs incorporated controlled blasting techniques to minimize blast-induced damage on the shaft walls. The full-face method has been very effective, with 3.5-m (11.5-ft) rounds being advanced.

Jan 1, 1990

Stratabound uranium deposits consist generally of two comingled geologic and statistical populations. Barren zones, usually having radiometric assays too low for recording on digitized logs, comprise a large portion of a mineralized stratum. In between are mineralized zones; where the grades are distributed essentially lognormally. Estimation of open-pit ore reserves requires the prediction of the tonnages of selective mining units (the smallest mined volume which may be segregated as ore or waste) and their grades within panels of convenient size for open pit planning and economic analysis. The proportionate tonnage of mineralized selective mining units within each panel can be predicted by kriging an an indicator function assigned to each composite (1 if mineralized, 0 if barren). Next, using logarithms of mineralized assays, the conditional lognormal distribution of grades of mineralized selective mining units can be found. Using this distribution and the krigedestimate of the probability a selective mining unit is mineralized, the grade and tonnage of selective- mining units above any cutoff can be predicted. A case study illustrating this two- step procedure is presented for the Imouraren uranium deposit located in the Republic of Niger. Using cross validation, the estimation procedures were checked and were shown to be adequately accurate for mine planning purposes.

Jan 1, 1979

By Gerald L. Finfinger, Michael A. Trevits

Since 1964, the US Bureau of Mines has been conducting a comprehensive program of research on the origin and control of coal bed gas. Several extensive databases have been developed during the work representing information from every major coal producing region in the United States. Gas content measurements have been made on 885 coal samples from 15 states representing 221 coal beds. Records indicate that the range of gas content varies from zero to over 640 ft3 per ton (20 cm3 per gm). During the conduct of the research program, several drilling and completion techniques have been developed or refined to divert and collect coal bed gas before it enters the mine environment. Such techniques include horizontal, cross-measure and vertical boreholes. Samples of gas collected from boreholes drilled under the program indicate that the primary gas constituent is methane which comprises 97 pct, the remaining hydrocarbons make up approximately 0.2 pct. Nitrogen and carbon dioxide account for the majority of the remaining gases at average concentrations of 1 pct each. Surveys have been made on the total daily gas emissions from underground coal mines. In fact, the most recent survey indicates that 180 mines had emissions in excess of 100 Mft3 per day (2.8 Mm3 per day). Furthermore, total mine emissions were in excess of 300 MMft3 per day (8493 Mm3 per day). An analysis of the data showed that there appears to be no relationship between in-place gas content and coal bed gas composition. Furthermore, no correlation was observed between in- place gas content and daily mine emissions. In a general sense, the higher the gas content the higher the relative gas emissions. Perhaps a more direct relationship would be observed if more complete emissions information (including gob gas borehole production) was available.

Jan 1, 1989

By J. Linhart

In vertical airways, falling material - solids-or water - may cause undesirable disturbances in the ventilation in the airway itself and also in neig¬bouring airways unless precautions are taken to stabilize the air flow. Such cases can occur, for example, - in shaft sinking by drilling from a pilot hole, - during the filling up of shafts, and - during the introduction of water into shafts in the case of mine fires. In an airway with upward ventilation the falling material will reduce the air flow and may even re¬verse its direction. In an airway with downward ventilation the air flow can only increase, but a reversal of the direction of ventilation may result in a parallel airway. These disturbances in the normal ventilation are undesirable as it must be the aim to have ventilation that is stable in quantity and direction throughout a mine. In order to be able to prepare suitable stabilization measures one must know the pressure generated by the falling material; this pressure will henceforth be called "aeromotive" pressure. The main factors determining the influence of falling material on the ventilation are - the amount of falling material and its height of fall, - the cross sectional area of the airway, - the pressure. difference prevailing in it, - the-position of the. airway in the ventilation. network, - the air velocity, and - other parameters, e. g. the density and grain size of the falling material. To determine the aeromotive pressure-measurements have been made underground during the sinking and filling of shafts and systematic studies have been carried out during the supply of water into a staple shaft. The present paper deals first with some fundamental theoretical considerations and then describes the measuring arrangements and the results of the series of experiments that have been carried out.

Jan 1, 1980

By Angela Binder, Oliver Langefeld

"The future of mining will be characterized not only by the application of modern technology, but also by the harmonization of economic, environmental and social issues. These areas set major future challenges which are complex and demand extensive knowledge. As an example, mining of highly complex orebodies for the supply of often critical raw materials, needs to consider technically demanding and cost-intensive extraction issues. The amount of tailings, which need to be stored, increases with the amount of ore mined. Therefore, the negative impact on environment and society increases. Hence mining becomes expensive with regard to all three aspects: economy, environment and society. In view of a sustainable mining practice this challenge should be used as an opportunity. The positive impact should be maximized for present and future generations. The objective is to create and use the mining openings in an optimum way related to sustainability. The approach of Blue Mining, which focuses on energy and ergonomics in the field of Sustainable Development, enhances the closure planning by recommending subsequent usage of such openings for energy storage. The approach fosters among others the implementation of the 7th Goal for Sustainable Development defined by the United Nations with the assurance of access to affordable, reliable, sustainable and modern energy for all. The usage of underground storage increases the stability of solar and water power usage, which are otherwise unreliable. Blue Mining embeds these issues in the main planning effort long before groundbreaking. This approach involves experience from past and current projects. This paper introduces the concept of Blue Mining with respect to post-mining utilization of a mine for energy storage. Methods and perspectives are presented with examples covering best-practices and lessons-learned."

Jan 1, 2017

Stope width was controlled around 3.5 feet for the narrow high grade vein system at Hollister Gold Mine. Without top access, backfill material was pumped from bottom access up into stope through a series of pipes after ore had been slushed out in each mining cycle. Backfill material was changed from one layer of low strength concrete plus one layer of high strength concrete cap to one layer of low strength cellular concrete plus one layer of high strength concrete cap. Backfill cost was cut down to 30 percent during this process. To reduce the steel concrete pipe set up and tear down time which was about 2 to 3 shifts in each mining cycle, steel pipes were left in man-way between mining cycles. Cellular concrete was firstly introduced into backfilling stopes at Hollister mine in Nevada Mining. This process including concrete pump selection, pumping pipe selection, material mixing, material mechanics and quality control were fully covered in this paper. CUT AND FILL MINING CYCLE The most flexible mining method, cut and fill (Figure 1), was used to mine the high grade, narrow steep vein system on this Northern Nevada property which is located eighty miles north east of Winnemucca. Without top access, stopes were accessed through two man-ways on each end, in which people travel ladders and material transport slides were set up (Figure 2). Each mining cycle was called a cut, from 6 to 8 feet high. Overhand sequence was used. Mining cycle started with drill and blast the middle portion of the stope, then expanded towards both ends. Broken ore was slushed into mill hole located at middle of the stope and then mucked out through bottom access into main haulage. Stope length was about 300 feet, which was restricted by slushing distance. Timber man-ways and mill hole would be raised and established for backfill and ready for the next mining cycle.

Jan 1, 2011

By Charles G. Weakly, Alan M. Lander, Pamela B. Zohar, Robert W. Leonardson

The cluster of gold deposits at the Goldstrike property is located in the Northern Carlin Trend in northeastern Nevada (Fig. 1). At many mature mining camps like Goldstrike, exploration innovation and success may wane with time. In this regard, sufficient exploration drilling was conducted in the area immediately north of the ultimate pit crest and under the final planned pit wall to test for a major deposit. No indications of large deposits were found, however, the majority of drill holes did intercept mineralization. Mining along the northern pit wall exposed significant structurally controlled ore-grade mineralization that had been missed by exploration drilling. In 2002 and early 2003, the mine geology group added reserves to the pit and improved the definition of underground resources by targeting specific ore-controlling structures within favorable stratigraphic units by utilizing relatively inexpensive horizontal RC drilling from the pit wall. The widespread occurrence of mineralization to the north of the pit was re-interpreted to be an indication of continuity of these mineralized zones. In January 2003, 70 feet of 0.332 opt Au at a depth of 710 to 780 feet was intercepted in a dewatering well. This intercept was significantly thicker and higher-grade than average for the area, which confirmed the existence of high-grade structural continuity, and helped secure management support for additional exploration. A timely and cost effective solution was needed to confirm the potential of the area. Immediate follow-up drilling on tighter grid spacing was rejected in favor of improving the geology model. Exploration across the property would benefit from an improved geology model, but to provide results in a timely manner, the area to the north of the Betze pit was chosen as a starting point (Fig. 2).

Jan 1, 2005

By James Matlock

The announcement of a minable reserve of 13.6 Mt (16 million tons) averaging 0.9 g/t (0.027 oz per ton) Au and 2.4 g/t (0.71 oz per ton) Ag for the open pit-heap leach reserve at Red Mountain No. 3 in Ouray County, Colorado, by Cornucopia Resources in November 1985 brings another open pit-heap leach precious metal ore body to the production stage. With about 8.2 Mt (9 million tons) of waste and metallurgical studies showing acceptable recovery rates, low reagent consumption, and good final percentage recovery, Red Mountain is a discovery that will add to the precious metal inventory of the US. Frank Baumgaruler of Denver, CO, recognized the precious metal potential in Red Mountain No. 3 and acquired all of the old claims. James Matlock conducted a field reconnaissance over Red Mountain No. 3 independently of the Baumgartner activities and recognized epithermal alteration and mineralization in the Tertiary volcanics. He recommended acquisition of the ground and was able to obtain rights and drill six core holes for Amoco in 1982. Amoco drilled a further nine core holes in 1983, but then dropped the property. Cyrano Resources examined the data and through its consulting geologist, V.F. Hollister, acquired the rights dropped by Amoco. In 1984 Cyrano began further drilling of the ore zone demonstrated by Amoco but they were then acquired by Cornucopia Resources. Cornucopia completed development of the property and commenced the permitting process in 1986. The property was recognized as a disseminated gold deposit by both Baumgartner and Matlock, and both deserve credit for properly evaluating mineralized outcrop in the Tertiary volcanics. However, Cornucopia recognized the profit potential in the heap leach exploitation of the ores and de- serves credit for completion of premine feasibility studies. The discovery is clearly a geological one, but the premine engineering studies were essential to the conversion of the prospect to a commercial mining enterprise. The deposit lies on the circular bounding fault of the Silverton caldera. Two reprints follow that help understand the geologic setting of the ore controls.

Jan 1, 1990

By J. G. Groppo, S. M. Khandrika, B. K. Parekh

It is shown that dewatering of fine coal particles (D50 = 21 µm) is enhanced near the point-of-zero-charge. The coal surface is modified by the addition of copper ions and by adjusting the pH to precipitate surface-active metal hydroxy species, which promote agglomeration and produce low-moisture cakes. Filtration kinetics data are used in calculating filter cake parameters from an integrated form of Darcy's law. The influence of copper ions and pH on filter cake parameters and the correlations among them are presented.

Jan 1, 1995

By J. C. Stankus, S. Guo, S. S. Peng

In this paper, a model is developed for a resin anchor bolt system in which the smooth bar is modeled by using one-dimensional truss elements, and the resin annulus is modeled by using axisymmetric elements. These two submodels are combined and then incorporated into an existing computer code called Roofbolt. After this development, all of the components in the resin anchor bolt system, including smooth bar, bearing plate and resin annulus, can be correctly modeled.

Jan 1, 1997

By T. C. Rao

The quantum of coal fines below 6 mm in run-of-mine (ROM) coal has been increasing due to progressive mechanization of mining methods which has created a substantial incentive, worldwide, to develop suitable fine coal beneficiation techniques. The majority of the efforts have been directed toward reduction in ash/sulfur contents in clean coal. The beneficiation techniques may be broadly grouped as those based on specific gravity and surface property. The processes, which use heavy medium cyclone, water-only cyclone, concentrating tables, and spirals, belong to the former group while the latter group encompasses froth flotation, column flotation, oleo- flotation, and oil agglomeration. In almost all the gravity based techniques, it has been noted that a classification step prior to beneficiation is essential for effective treatment. In general, the effect of design and process variables on the performance of these units and also the quantification of the processes have been the main areas of research and development. In froth flotation, efforts throughout the world have been mainly to understand the effect of variables and to optimize the process. Quantification of the process has been attempted through kinetic studies and mathematical modeling. The efforts have led to the development of new reagents, machine designs, and flowsheets for a specified objective. The attempts so far with the column flotation and oleoflotation processes have indicated a great potential. Extensive R&D efforts are in progress to understand as well as to commercialize the processes. The efforts in the oil agglomeration process have been toward substantiating the inherent merits of the process by developing cheaper bridging liquids and technology to recover and reuse the oil to make the process commercially viable. Modeling of the process has also been attempted to predict the yield and size distribution of the agglomerates. This paper reviews and summarizes the recent developments in the science and technology of fine coal beneficiation processes. The current trends in R%D efforts for these processes are also highlighted.

Jan 1, 1987

By P. R. La Pointe, H. C. Ganow

The production of both over- and undersized coal fragments is a constant problem to open pit operators in the Powder River Basin. Operators strive to achieve production blasts that economically minimize the weight percentage of over- and undersize coal. However, natural fractures influence blast fragmentation, and can impose limits on the final fragment size distribution. ARCO&apos;s Anaconda Minerals Company studied the limits placed by natural fracturing as part of a wider geotechnical study of the Wyodak Coal in the eastern Powder River Basin, Campbell County, Wyoming. Measurements of fracture orientation, size and spacing were made at ARCO&apos;s Black Thunder Mine. These data were used to form statistical distributions for natural fracture size, spacing and orientation. An algorithm was created to select fracture properties at random from these distributions and to form hypothetical blocks. The blocks were then numerically "sieved" to derive pos- sible particle size distribution curves. These curves are compared to fragmentation results from samples taken from three test blasts. All test blasts yield very similar lognormal fragment size distributions. The median particle size varies from 1.25 to 2.0 in.(3.2 to 5.1 cm), the mean from 4.0 to 8.5 in. (10.2 to 21.6 cm). The standard deviation was about 1.6 in. (4.2 cm). Coal fines (fragments < 0.25 in. or 0.64 cm) are about 15%. Calculated fragment distributions for the natural fractures predict the median size well but underestimate the variance. Algorithm modifications to account for processes known to occur in the comminution zone near the blast hole significantly improve the match in the fine coal size range. The match suggests that spacing of fractures, rather than fracture length, controls the formation of fine- and medium-sized fragments. On the other hand, the oversize coal is controlled by the fracture lengths, rather than the spacing. Data from subsequent test blasts support this idea. By increasing delay times from 8 msec to 17 msec, engineers were able to reduce fines to 7% - 10% but could achieve no further improvement, despite changes in shot pattern geometry, decking and hole size. The hypothetical fragment distributions show that, even without blast enhancement, about 5% of the natural coal blocks are fine-sized.

Jan 1, 1986

By W. Everett Smith

Factors that have influenced mineralization in the Valley and Ridge and Piedmont provinces in Alabama are not clearly understood. Lithology and structure are recognizable factors in the Valley and Ridge province, where barite, lead, and zinc sulfides occur in structurally complex areas of Cambrian and Ordiovician carbonate rocks. Metal mineralization in the Piedmont province indicates a complex relationship with factors such as favorable host rock, proximity to intrusive or high-grade metamorphic rocks, several metamorphic events and separate or related structural events. Lineaments, as used herein, refer to naturally occurring linear features consisting of topographic, vegetative or soil tonal alignments that are at least partially continuous for distances greater than a mile (Lattman, 1958). Lineaments in Alabama were first recognized by J. G. Newton in 1970, using Apollo 9 series photographs. Subsequent studies delineated the features (Powell and others, 1970) and suggested relationships to structural and hydrologic factors. More recent work has explored relationships to mineralization, environmental geology and the tectonic framework of the Appalachians (Drahovzal and Copeland, 1970; Drahovzal and Neathery, in press). The lineaments recognizable on Apollo 9 photography probably represent fractures, some of which may reflect geofractures that bound major basement blocks. The lineaments defined in Alabama range from about 4 miles to nearly 200 miles in length. Most of the lineaments are straight, but some are arcuate; some appear to terminate at the intersections with other lineaments but most cross each other with no offset. Some lineaments pass through areas of structural disruption such as terminations, offsets and changes in structural style, but others show no such relationships. Most of the lineaments appear to cross topographic features with little or no obvious disruption. Orientation analyses of the lineaments divide them into three directional groupings

Jan 1, 1972

By Yongqin Zhang

A single bubble released into surfactant solution first accelerates, reaching a maximum velocity then decelerates to reach a terminal velocity. Modeling this "velocity profile" is fundamental to understanding the motion of bubbles in flotation systems. This contribution considers the terminal velocity. Modeling is by a combination of the Navier-Stokes equation for flow around the bubble and the Marangoni effect induced by surfactant on the bubble surface. Numerical simulation is shown to agree with experiment for bubbles in pure water and surfactant solutions.

Jan 1, 1999

By H. Sevim

This paper summarizes the research effort in simulating the operation of "Underground Coarse-Coal Hydrotransport Systems" (UCCHS). The equipment of the system to be simulated is already optimally selected by using an analytical optimization model. The purpose of the simulation model is to test the performance of the system and to obtain the distributions of operating parameters such as water and power consumption and amount of slurry delivered to the preparation plant. Knowledge of the distributions of these parameters is essential for the efficient operation of the system.

Jan 1, 1987