Search Documents

By Harry Sutcliffe

THE PROBLEM Two and a half years have gone by since the December, 1976 Civil Engineering article on subway costs caused such a furore. What has happened in this interval? Even after discounting the crushing inflation rate, costs are still increasing, and there is no sign of a turndown, even in the rate of increase. Some steps outlined in the article have been taken. In April this year, the first D.O.T.-sponsored Peer Review Group, made up of managers of other transit properties, met in Boston to review MBTA's $500 million Red Line Extension-Northwest for cost effectiveness. While the impact of a review at the end of the design phase, with substantial segments under contract, cannot be as effective as a review early in the design phase, it is nevertheless a start. This first meeting will be followed by a review of Boston's Orange Line relocation, the final design for which is just underway. In the industry at large two facts are evident: 1. We are failing to reduce underground construction costs. 2. Underground construction is in danger of pricing itself out of the market place. It has always been a greater challenge to design a Chevvy than to design a Cadillac, but it is the Chevvy we need today. Much attention has been focussed in the past on engineering design in the narrow sense: areas such as ground loading conditions and concrete design. This paper will attempt to make the case that costs in urban underground construction are primarily outside the area of structural

Jan 1, 1979

By Edward M. Dowey

The concrete lining for a long 8.05 km (5 mi) section of New York City Water Tunnel No. 3 was cast in place. The contractor, Grow-Perini-Skanska, placed over76,841 m3 (100,505 cy) of concrete, pouring 24 hours per day, 5 days per week. The concrete was dropped 204 m (670 ft) to the tunnel level, transported by rail to a concrete remixer and pump, and placed in 146.3m (480 ft) of full circle forms. Some of the many challenges include the sheer magnitude of the job, navigating through drifts, a raise and curves, dealing with ground water inflows, and placing the concrete within time limits.

Jan 1, 2001

By Christopher J. Bise

INTRODUCTION Traditionally, the purpose of mine ventilation has been defined as diluting, rendering harmless, and sweeping away hazardous gases which may accumulate in the mine workings. In addition, the ventilation sys- tem must keep the mine air as close as possible to the composition of the outside air in order to provide a healthy environment for mineworkers and to prolong the useful life of mine equipment. When plans are being developed for opening a new mine, sound engineering dictates that a calculated estimate be made of both the maximum air quantity requirement and the accept- able mine pressure (head) loss related to the under- ground layout and projections. For efficient mine ventilation, the two problem areas that demand constant attention are (1) the control of fugitive air (through short circuiting or leakage) and (2) the provision of ample airway capacity. Fugitive air is that quantity of air which enters the mine but short-circuits the mine ventilation system through improperly constructed stoppings, doors, overcasts, etc.; it represents an investment in power consumption (to move the air by the fan) while providing little, if any, return on the investment. Typically, efficient mines are those that can deliver 50% of the air handled by their fans to the working faces. Paying close attention to a new mine's ventilation system at the outset can provide numerous benefits during the later stages of mine development. It has often been noted that the main cause of trouble in many mine ventilation systems can be found within a radius of 2500 ft from the fan installation. Ample airway capacity is essential to maintain the mine's head loss within manageable limits. Similar to an industrial ventilation setting, the mine's headings are the ductwork for the handling of air. The difference between normal industrial ventilation and mine ventilation is apparent when more capacity is needed; a plant can install new or larger ductwork, but it is difficult for a mine to install new entries or enlarge existing entries. Air velocities are usually maintained under 800 fpm to limit the stirring up of dust in the intakes. With this in mind, it is usually simple to estimate the number of entries required in the ventilation system. The problem that often arises, though, is when the system's capacity is overestimated and the required head loss to achieve the desired quantity is excessive. Experience has shown that problems are often encountered when the mine's condition requires much more than three inches of water gage to ventilate the mine on a day-to-day basis. Thus, if proper attention is not paid to these parameters in the preplanning and initial development of a new mine, it may take an extremely high water gage to achieve the ultimate quantity. This chapter will not delve deeply into the theory of mine ventilation; many other books have been writ- ten on that subject. Instead, the following sections will point out the important considerations that should take place before the development of a mine ventilation system, as they relate to normal industry practice. FUNDAMENTALS OF AIRFLOW Volume Versus Water Gage The common method of measuring ventilation pressure is in terms of inches of water gage (wg); one inch of water corresponds to a pressure of 5.2 psf (pounds per square foot). Further, airflow follows a square-law relationship between volumes and pressures where, as shown in the previous section, a doubling of quantity requires a quadrupling of pressure. Table 1 shows how heads and quantities are related. Using Table 1, it is readily apparent that, for the same mining conditions, an increase in pressure from one inch wg to three inches wg results in only 34,640 cfm when the initial quantity is 20,000 cfm. Pressure Losses Pressure losses in mine ventilation systems are caused by friction between the heading walls and the air stream and by shock losses due to abrupt changes of the air stream caused by obstructions. The common pressure-loss formula for mine ventilation is: [ ] where H is the pressure loss in inches of water gage, K is the coefficient of friction, L is the length of the airway in feet, 0 is the airway perimeter in feet, V is the air velocity in feet per minute, and A is the cross-sectional area of the airway in square feet. Table 2 lists the US Bureau of Mines schedule of friction factors (K) for mine airways. Recent research indicates that the values of K are slightly less for coal mines than those presented in the USBM Schedule, and Table 3 should be consulted in this instance. It should be

Jan 1, 1986

By Arthur D. Silber

The economic success and growth of any metropolitan region depends on mobility. Today, mobility between New Jersey and New York is threatened by a transportation system that cannot meet 21st century travel demands. The transportation bottleneck created by the Hudson River threatens the viability of one of the world?s great centers of commerce and culture. Fortunately, there is a solution: The Access to the Region?s Core Mass Transit Tunnel. The US$8.7-billion Mass Tran-sit Tunnel?s (MTT) new two-track line will double commuter rail capacity under the Hudson and create a new, state-of-the-art cavern station in Midtown Manhattan, with wide platforms, high-speed escalators and other features to improve riders? travel experience. The capacity and other benefits of the MTT project will launch a new era of prosperity for the region, just as the Pennsylvania Railroad did almost 100 years ago when it built the existing two, single-track rail tunnels that now form the sole commuter rail link between New Jersey and New York. The existing tunnels run from North Bergen, NJ, under the Hudson River to Pennsylvania Station at 33rd Street in Manhattan. Construction on the MTT, the largest public works project in the United States, is scheduled to start this year and continue through 2017. The MTT is ready to go to construction thanks to a major commitment of financial, engineering, project management and other resources from NJ TRAN-SIT, New Jersey?s statewide mass transit agency, and the Port Authority of New York and New Jersey, a bistate agency that operates the Holland and Lincoln tunnels, the George Washington Bridge and other major transportation facilities in New York and New Jersey. The project is also strongly supported by the state governments of New York and New Jersey, as well as that of New York City. The MTT is New Jersey Governor Jon Corzine?s number one transportation priority.

Jan 1, 2009

By Ramon LaRusso, Frank Wheby, Richard Acker

Field investigations and office studies were used to develop criteria and cost parameters related to the geologic aspects of the proposed project. These results were employed in optimization of layouts and comparison of alternative schemes, leading to selection of the recommended program. Study of project features included the development of subsurface shafts, tunnels, and mined storage areas, and the utilization of existing surface quarries. These project features were proposed for construction within the bedrock units underlying Chicago. Principal geologic considerations included bedrock structure, stratigraphic sequence of units, rock competence and uniformity, and requirements for aquifer protection. All geologic factors were interrelated with other project considerations such as surface hydrology, hydraulics, and urban setting. Data for analyses was acquired through an exploration program conducted intermittently between 1967 and 1971, in addition to that already available through numerous explorations and well constructions in the project area. The exploration program included seismic surveying, core drilling, geophysical borehole logging, and water pressure testing of boreholes, and water well drilling and testing. Extensive laboratory tests were conducted on core samples. The data formed the basis of studies enabling the formulation of preliminary design and siting criteria resulting in construction cost evaluation.

Jan 1, 1997

By Charles W. Daugherty

INTRODUCTION The Washington Metropolitan Area Transit Authority's (WMATA's) rapid transit system, Metro, ultimately will comprise 162.5 km (101 miles) of line divided among 10 routes. As shown in Figure 1, about 24 km (15 miles) of the system will consist of mined rock tunnels distributed along the A, B, C and K Routes. The structural construction contracts for all of the A, C and K Route rock tunnels are complete and trains are running in about one-third of them. A contract for construction of rock tunnel section B-9, the southernmost third of the B Route, was awarded on June 27, 1980. The final design of Sections B-10 and B-lla, the remainder of the rock tunnel portions of the B Route and the Metro system, are well advanced and should be under con¬struction by 1982. Of Metro's 87 stations, 11 will have been constructed by mining in solid rock, a not inconsiderable achievement, since each structure must be over 183 m (600 feet) long, wide enough to accommodate two trains and one or two passenger platforms, and high enough to achieve a stable arching action without encumbering columns. With the passage of years, some original priorities have been reordered, and ways have been sought to streamline and simplify this most complex of Metro structures without grossly violating the architectural standards that make it unique. This paper will summarize that search, and describe the design and construction aspects of the resulting product, the dual chamber rock tunnel station.

Jan 1, 1981

By F. W. DeVries, O. B. Mathre

Addition of Kastone® peroxygen compound and formaldehyde to cyanide gold extraction process effluents, containing at least 5 mg soluble copper per liter, will oxidize acid-dissociable cyanide to levels less than 0.2 mg per liter, without appreciable oxidation of thiocyanate. Most of the copper precipitates and is removed by filtration of the treated solutions. The treatment can be completed in less than 2 hours when the excess of hydrogen peroxide over the cyanide is about 75-100 mg per liter. The excess hydrogen peroxide destroys residual formaldehyde and then is catalytically decomposed by the copper-containing solids that separate, so it will not interfere with subsequent operation. A pilot plant using this technology has been operated for more than four months at rates from 1-2 gpm. Clear, filtered effluent containing less than 0.2 mg acid-dissociable cyanide per liter has been produced.

Jan 1, 1981

By J. R. Parga

In mineral processing, poor froth-flotation performance translates into both an enormous loss of revenue and an unnecessary waste of the ore reserve. In this context, Bacís Mining Company developed a versatile new, high-performance flotation-cell design that can be incorporated into various flotation circuits. The main feature of this circular cell is that it is comprised of two separate sections, namely, a flotation cell that uses wash water to minimize the entrainment of fine gangue particles into the froth product and an external bubble generator that produces small bubbles of relatively uniform size at a specified aeration-rate. The air/water mixture is blended with the pulp by gentle agitation, so as to enhance particle-bubble aggregate-stability. Comparative metallurgical performance with conventional flotation cells show that the power requirements and operating costs for precious metal flotation are three times lower, while the concentrate grade is 7% higher and the recoveries of precious metals are 5% higher.

Jan 1, 2009

By Paul Hewitt, Tim Smirnoff

Design and construction of the Epping to Chatswood Rail Line tunnels in Sydney, Australia required an innovative approach to define hydrogeological properties of the Sydney Hawkesbury Sandstone and provided an insight into the hydraulic behaviour of fractured sedimentary rocks. To meet restrictive water inflow and infiltration criteria both the pre-treatment of zones of fractured or highly jointed rock, and waterproofing using an interior spray on membrane for the finished drained tunnels and stations was required. Methods typically used to address the interaction of groundwater and tunnels in the Sydney Basin are demonstrated by case histories from major design-build tunnel projects.

Jan 1, 2005

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica surfaces immersed in solutions of hydrolysable cations and/or sodium oleate. Hydrophobic forces were observed at the pH range where the concentration of the singly-charged hydroxo-complexes (CaOH+ or MgOH+) in solution is the highest. In the absence of oleate, the adsorption of the hydroxo-complexes was indicated by the disappearance of the repulsive hydration force. These results suggest that the hydrolysable cations adsorb on silica as singly-charged hydroxo-complexes. Based on the results obtained in the present work, a model for the adsorption of hydrolysable cations has been developed.

Jan 1, 2009

By N. A. Abdel-Khalek

The amenability of carbonate separation from a sedimentary phosphate ore using a bioflotation process was studied. Two types of bacteria were chosen for this study. The experiments were performed using oleic acid as collector. The flotation experiments were carried out using statistical designs for optimizing the main operating parameters. A concentrate containing 0.78% MgO and 30.15% P2O5 with a recovery of 92.31% was obtained from a feed containing about 2.45% MgO and 27% P2O5. These specifications could not be obtained using conventional flotation experiments under similar conditions in the absence of bacteria. Measurements of zeta potential, adsorption of bacteria and collector, as well as froth power, were performed to explain the role of microorganisms in the surface modification of both dolomite and phosphate and in their interaction with the collector.

Jan 1, 2009

By Steven W. Hunt, Safdar A. Gill

Design and construction of temporary shafts for underground facilities often require evaluation of bottom stability due to rupture (blow-ins) caused by water pressure acting on a bottom plug. This paper provides an overview of shaft bottom stability evaluation methods for the case of a relatively watertight soil plug which overlies an artesian aquifer. Methods of considering plug perimeter shear, plug buckling and pressure relief are discussed. Minimum factors of safety are suggested. Future use of the shaft subgrade is also considered. Bottom plug failure case histories at several shafts are evaluated. This paper should be useful to project designers, ground support system design engineers and contractors involved with construction of shafts for underground facilities

Jan 1, 1997

By S. Asokan, D. Rathod, Ch. V. G. K. Murty

Tata Steel, a steel arm of Tata Group, is Asia's first and India's largest integrated private sector steel company. Tata Steel’s turnover in fiscal 2004-05 was nearly US$ 3.25 billion. As part of its vision to grow in related industries, Tata Steel is poised to enter the Titania businesses in the Indian state of Tamil Nadu. The Titania project will involve mining, separation of ilmenite & other co-minerals, beneficiation of ilmenite to synthetic Rutile and further maximum value addition to Titanium metal. This paper outlines the journey from the concept to current findings of the Bankable Feasibility Study in developing Sattankulam Heavy Mineral Sands Deposits in the State of Tamil Nadu, India by Tata Steel.

Jan 1, 2005

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009

Narrow vein mining, with enough challenge and also where the cutting edge technology can be applied, is still a very important and exciting portion of the mining industry. Based on the deposit characteristics, the most flexible mining method, cut and fill, has been being tested mining this high grade Northern Nevada property, Hollister, since the year of 2008. In the last three years, 254,000 tons of ore were hauled out of the portal and 23,000 feet of development were excavated underground with the winning of several safety and environmental awards. Together with mine geology, the essential segments include mining cycle, ground control, ventilation, grade control and backfill method in cut and fill stopes were covered in this paper.

Jan 1, 2012

By C. Treworgy, C. Chenoworth

Geologic and technical factors such as coal seam thickness, stripping ratios, roof conditions, partings, faults, and size and geometry of the reserve block greatly impact the availability of Illinois coal for mining. Residential and commercial developments also restrict access to coal reserves in some areas. Despite the collective effects of these factors, large blocks of bituminous coal reserves suitable for efficient, low-cost underground mining remain available in Illinois.

Feb 24, 1997

By N. Arbiter, C. C. Harris

The economic advantages of large diameter ball mills can be compromised by unexpected capacity limiting conditions. These arise because media rotational flow to ore axial flow ratios, and the number of mill revolutions that ore is subjected to during residence, are both inversely proportional to mill diameter. Because of this, mixing efficiency and grinding kinetics may decrease and become capacity limiting when mill diameters reach a critical range. There are two possible scale-up problems involved in the design and use of mineral processing machinery: • Selecting the size and operating conditions for available larger equipment, to insure that operating results will match those obtained with smaller units; or •Extending the size ranges of equipment beyond existing limits. Previous research at Columbia University into flotation machine hydrodynamics has demonstrated the importance in scale-up of internal flow relationships; these perform a similar role in grinding (Arbiter and Harris, 1980).

Jan 1, 1982

By C. G. Buttleman, W. C. Brice

In Minnesota, reclamation of active aggregate mining sites is primarily regulated through local permits issued at the county, township, or municipality. However, for abandoned or depleted aggregate mining sites, a responsible party for reclamation is often no longer available. Since 1995, the Minnesota Department of Natural Resources has reclaimed several abandoned aggregate sites using innovative public/private partnerships and emphasizing native plant materials. The purpose of these projects is to demonstrate cost effective reclamation methods that can be utilized by both aggregate operators and local government and to promote mine planning and resource identification as it relates to reclamation.

Jan 1, 2000

By V. G. Grechanyuk

The paper presents the mechanical properties of Cu-Mo composite materials depending on the molybdenum content. The influence of structural defects on the mechanical-physical properties of the condensates at stretching testing as well as of the lamellar grain dimensions upon the mechanical properties of Cu-Mo composite materials is also presented.

Jan 1, 2008

By Edward Skolnik

The concept of using fluid dense media to separate heavy ore constituents from the lighter gangue dates back to 1858, when it was patented by Sir Henry Bessemer. Its use in coal did not begin until after 1917, however, when Chance invented a process (which bears his name) in which lighter coal floats in a suspension of fine sand in water while heavier refuse sinks. Conklin used fine magnetite in suspension as a medium for floating anthracite in 1922, DuPont designed a plant employing organic liquids in 1936, and Belknap used a solution of calcium chloride (which Bessemer had suggested, among other media) in 1937. Separation of magnetic media by magnetic separators from the suspensions in which they were carried was introduced in a Butler Brothers ore concentrator pilot plant in 1937. The media first used were crushed steel and various grades of ferrosilicon. Since 1940, when American Cyanamid used magnetic separators to recover and clean magnetite in a coal washing circuit, virtually all heavy medium circuits have been of that type. As long as static baths are employed, as they are in the processes above, coal smaller than 9.5 mm or 6.4 mm cannot be cleaned economically in heavy medium. The settling velocities of the fine material are very low, and consequently the time required to separate the lighter coal from the heavier refuse becomes excessive. In addition, stray currents in the vessel and the upward velocities induced to keep media solids in suspension affect the finer solids to the degree that physical size becomes a more important factor than specific gravity.

Jan 8, 1980