Search Documents

By B. Rao Pothini, Julio H. Thaler, W. L. Finlay

The White Pine room-and-pillar mine started in 1955 from a suboutcrop, down gentle dips, and with a competent sandstone roof. As mining depths increased, extraction decreased 1% every 35 feet. Moreover, roofs became shaly and less competent, and regions of high fault and joint densities, sometimes with and some- times without high lateral stresses, increased the tendencies towards roof falls. Instinctive reactions towards narrower openings did not alleviate the problem. Careful consideration of rock mechanics principles culminated in the development of two variants to the conventional room-and-pillar mining system based on the concept of stress relief through load deflection. The two systems-EquiAdvance Cave, and PressureArch Panel Mining-are complementary. The objective of the former system is to provide relief from lateral stresses through advance caving and in the process also to achieve higher extraction at depth. Where surface subsidence cannot be allowed, the alternative PressureArch Panel concept is utilized to provide stress relief and moderately high extraction ratio. Both systems have been under trial for over three years and, together, produced over three million tons of copper ore. These two systems, and their production test results to date, are described.

Jan 1, 1977

By J. F. Stenebråten, W. P. Johnson, D. R. Brosnahan

Carbonaceous materials (CM) from ores of varying preg¬robbing activity from Barrick Goldstrike Mines Inc. (BGMI), Nevada, were characterized in terms of their functional group contents, hydrocarbon contents, elemental composi¬tions and humic acid contents. Fourier transform infrared (FT-IR) analyses did not show the presence of hydrocarbons or carboxylic, phenolic or sulfhydrolfunctionalities. The FT¬IR bands present included C=C stretching in aromatic rings and C-O-C stretching, indicating the presence of oxygen as ether linkages or thiocarbonyl functionality in the carbon matrix. Calculated atomic oxygen to carbon (O/C) ratios did not reveal a trend between the maturity of the CM and the preg-robbing behavior, possibly due to the low resolution inherent in electron microprobe analyses. However, the atomic O/C ratios agree with other chemical analyses, indi¬cating that the organic carbon is very mature, similar to or higher than anthracite grade coal. Gas chromatography¬mass spectrometry and nuclear magnetic resonance analy¬ses corroborated the relatively featureless character of the carbon, indicating that the carbon structure is virtually completely aromatic (graphitic).

Jan 1, 2000

By W. M. Shaver, W. R. Dengler

INTRODUCTION In Canada, most of the rock being broken in underground metal mines is being carried out using traditional drilling and blasting methods. Despite advances being made in hard rock boring and other, more exotic techniques, it is Dynatec's belief that the traditional methods will continue to prevail for many years to come. It is also our belief that modest research efforts expended on the traditional methods will result in substantial financial benefits to the mining and rock tunnelling businesses. Dynatec has pursued productivity improvements through the use of long rounds in both shaft sinking and lateral development. The concept of longer rounds was developed by Dynatec on the Craig Shaft Sinking Project (RETC 1991). This paper reviews the Craig Shaft Long Round success. This technology was subsequently utilized to sink the two shafts at Aur Resources with great success. The development of a Long Round Jumbo for tunnelling is a natural progression of the long round technology developed for the Craig Shaft. RECENT HISTORY OF SHAFT SINKING Shaft sinking is one of the oldest and most difficult mining methods. Due to the relatively small amount of shaft sinking in proportion to tunnelling and

Jan 1, 1993

By Stephen J. Reynolds

Arizona's geologic history is complex, resulting in a diversity of rock types and earth materials, including those of commercial interest. Regional variations in geologic history gave rise to three geologic provinces and an inequitable distribution of both metallic and nonmetallic mineral wealth. The Colorado Plateau is largely composed of flat-lying Paleozoic and Mesozoic sedimentary rocks and late Cenozoic volcanic fields and sedimentary deposits. Associated resources include gypsum, halite, sylvite, clays, specialty sand, flagstone, volcanic products, and aggregate. The adjacent Transition Zone features a large expanse of Proterozoic rocks, economically important Devonian and Mississippian carbonate rocks, and Tertiary volcanic and sedimentary materials. Nonmetallic resources in this province include facing and dimension stone, aggregate, decomposed granite, chrysotile asbestos, gypsum, clay, barite, fluorspar, zeolites, and limestone used for lime, cement, and railroad ballast. The Basin and Range Province has the most complex geologic history and, therefore, the most diverse assemblage of industrial mineral occurrences. These include halite, gypsum, clay, aggregate, decomposed granite, diatomite, zeolites, perlite, pumice, kyanite, limestone, marble, stone, and others. In addition, young stream deposits yield vast quantities of sand and gravel, Arizona's most economically important nonmetallic mineral commodity.

Jan 1, 1987

By G. Ansong, P. K. Achireko

The authors present a new mineral price model, compare it with time series and naive models, and analyze the effects of the forecasting models on mineral project evaluation. Mineral commodity prices are volatile, which means that the results of evaluation tools that do not treat the stochasticity of metal prices rigorously may be misleading. But, in mine valuation, commodity price forecasts are required to assess the economic viability of a project. In this study, a new mineral forecasting method, called the MNDRVG-MFNN-RM model, which incorporates randomness, neural networks and regression models, is introduced. The MNDRVG-MFNN-RM model, a naive method and time series model were used to forecast gold prices for two successive years for the evaluation of a proposed open-pit mine. The MNDRVG-MFNN-RM model yielded the best results among the three methods. It produced the true optimum pit limits and an optimum pit value slightly less than the true optimum value. The main novelty of the methodology is the simulation and rigorous analysis of the randomness property associated with mineral prices to reduce the estimation and forecast errors, an important contribution to mineral venture evaluation, mine planning and design.

Jan 1, 2000

By W. J. Kogelmann

Roadheaders, also called Boom Miners or Boom-type Tunneling Machines have been in North America since 1968, when first introduced by Willy Kogelmann, the founder of Alpine Equipment Corp. (?Alpine?). Roadheaders were invented in Europe in the late 1940s. Machines with in-line, axial cutter heads were developed in the former Soviet Union. The British Dosco DRCL is based on the Russian PK-3 roadheader. Roadheaders with transverse ?ripper? cutter heads were invented in Hungary (1). The Austrian-made Alpine Miners of VOEST-Alpine, purchased by Sandvik AB, are based on a 1965 Hungarian license. Roadheaders are widely used in the mining and tunneling industries because they can excavate drifts, entries and tunnels with cross sections of any shape and size, can handle mixed faces, work on steep grades, and negotiate tight curves and cross-cuts. A roadheader?s only major limitation is the strength and abrasiveness of rock and minerals to be excavated. This paper covers roadheader selection criteria, improvements in reliability, attachments for flexibility (Multi-Tool Miner), and automated support systems for increased cutting time for increased shift production.

Jan 1, 2008

By V. Anthony Cammarota

MINERALS INFORMATION PROGRAM Mineral data collection by the Federal Government actually began in 1882 with an appropriation by Congress to the U.S. Geological Survey (USGS). Although the Bureau of Mines was instituted in 1910, it was not until 1924 that the collection, interpretation, and dissemination of worldwide information on production, consumption, and availability of minerals became the responsibility of the Bureau. The objective of the Bureau's minerals information program is to maintain and provide reliable, timely, and comprehensive data for analysis of national minerals problems. This program is implemented by a staff of specialists who cover about 100 mineral commodities and the mineral industries of 168 countries. Data are also provided on the minerals industry on the State and county level. The specialists analyze information to identify trends and problems, forecast future U.S. and world supply and demand for the nonfuel minerals, and relate trends and developments to their impact on the domestic minerals industry. Data Sources and Publications The primary sources of data concerning the domestic minerals industry are the companies that produce, use, and trade in these minerals. Approximately 60,000 survey forms are sent to industry, on a monthly, quarterly, semiannual, or annual basis, to obtain the data. Domestic trade data are provided by the Bureau of the Census, U.S. Department of Commerce. Information on mineral developments abroad is developed by Bureau specialists from mineral reports supplied by U.S. embassies worldwide, from primary source documents, from a review of the technical mining literature, and from onsite mine and plant visits in foreign countries. The information is disseminated through a number of Bureau publications: "Mineral Industry Surveys" provide aggregated data on a monthly. quarterly, or semiannual basis to give timely information on the most important mineral commodities. "Mineral Commodity Summaries," published each January, provides preliminary annual data on supply and demand and discusses significant events of the previous year. The final data are published later in the "Minerals Yearbook," which is the definitive historical record for mineral statistics. "Mineral Facts and Problems," an encyclopedic work issued every 5 years, covers industry structure, technology, supply-demand analysis. economic factors, reserves, and forecasts of U.S. and world demand for individual commodities. "Mineral Perspectives" and "Mineral Issues" cover important international mineral developments and significant issues of current U.S. policy as they relate to minerals. Discussions and analyses of mineral trends and developments also appear in other Bureau publications, such as "Minerals and Materials" and "Information Circulars." These publications provide the basis for analysis and policy determinations by the Bureau and by virtually every Federal agency concerned with minerals, defense issues, the national economy, and foreign relations. The data are also used by industry in planning capital investments in mines and processing plants, by financial analysts, by U.S. delegations in their work with international commodity groups, and by a host of other minerals related organizations. Data Bases The data bases used by the specialists for preparing publications or in response to a continuous stream of inquiries include both those that contain individual commodity data from respondents, and those that are summary data bases on production, trade, capacity, employment and a number of other minerals-related items, not all of which are derived from data reported to the Bureau of Mines. The data bases maintained on the mainframes are not accessible by non- Bureau users. A 10-year data base of supply- demand data, published each year as an update of tables that appear for each commodity in Mineral Facts and Problems, is available on a floppy

Jan 1, 1987

By V. Kontogianni

The underground extraction of coal is associated with ground movements extending from the mining area to the ground surface, which result in bowls of ground subsidence, with amplitude exceeding the amount of several meters and occasionally with important tilt and curvature of ground surface. Such changes at both the underground environment and surface topography lead to destruction of buildings, failure of utilities and transportation networks, and occasionally formation of areas vulnerable to flooding, or even small pools. Based on geodetic surface measurements of ground elevation changes, various theories and empirical models relating surface subsidence with the geometry of underground voids formed have been proposed, and predictions of expected subsidence in the form of contours have been estimated. In this study a case study of planning of a new highway network through areas in which coal extraction was also planned is discussed. This work is partly funded by EU. The optimum solution selected was a modification of the initial highway planning, so that the road is increased in length and by-passes the richest coal-field, where maximum post-exploitation subsidence was predicted, and only crosses either minor coalfields, which are not to be exploited, or even margins of main coalfields, in which minor post-exploitation subsidence is expected.

Jan 1, 2006

By C. Steiakakis

Over recent years large construction projects have taken place and will be taking place in complex geological environments. In order to reduce costs and increase safety, a detailed geotechnical evaluation of local conditions is very important. This issue has been addressed in much detail for soils and hard rocks but there is a gap in intermediate geomaterials such as soft or altered rocks. In order to overcome this problem geotechnical engineers usually adopt principles and methods meant either for soil or hard rocks. The rock mass classification systems such as RMR, GSI etc. are the ones predominantly used. The users of these systems are of-ten unaware of the theory, limitations or the data behind these systems. The aim of this paper is to demonstrate problems or misuses of rock mass classification systems in intermediate geo-materials. The main focus is on the GSI classification system since it is widely used in Greece. Complex geological environments, altered, weathered or poor rock materials are addressed and suggestions on how they should be evaluated with the use of rock mass classification systems are discussed. Situations where the use of these systems produce erroneous results not due to their limitations but rather due to lack of experience and incorrect use are also discussed. Finally, recommendations are made for better use of these systems in practical problems

Jan 1, 2005

By F. F. Aplan

The material known as coal has a highly variable composition. As a consequence, coals show a great variation in their physical and chemical properties as a function of coal rank. The situation is further complicated because the preparation engineer must deal with raw coal, as mined. This is an assemblage of coal, upwards of 30% mineral matter and, typically, several percent pyrite. The kind and amount of the mineral constituents is also highly variable from source to source. A knowledge of coal rank and source location, and the kind and amount of associated impurities, is the first step in evaluating the response of a raw coal to preparation procedures. The raw coal must first be characterized before information from one source can be extrapolated to that of another.

Jan 1, 1988

By Karel SPIRKO

The one-dimensional mathematical model of unsteady-state heat conduct ion through multilayer (wall and floor of airway consist of several layers of material and rock) and two-surface (dry and wet surfaces) airway wall and airway floor with convective heat and moisture transfer between their surfaces and mine air with time dependent changes of temperature and humidity has been developed on the basis of introduction of acceptable simplifications of description of heat and moisture transfer between rock mass and mine air. The analytical solutions for calculation of the surface temperature of any type of surface of airway wall/floor and for calculation of water vapour pressure near the wet surfaces at given time are obtained by means of the model presented. These solutions are illustrated for the case of general harmonic course of air temperature and humidity. Balance of heat and moisture transfer between surfaces of airway wall and floor and mine air is solved by an iterative method in the partial sections of airway. The temperature and the humidity of mine air on the outlet of each partial section of airway at given time are its resolutions and they are the input data for following partial section. By this way it is possible to solve complicated dynamic changes of mine air temperature and humidity in an air way system by relatively simple mathematical apparat.

Jan 1, 1991

By R. A. Pond

Two 6.17 m (20 ft 3 in.) diameter raises, concrete-lined to 5.49 m (18 ft) inside diameter, were completed in 1978 at the Monterey Coal Company Number One Mine near Carlinville, Illinois, by Frontier-Kemper Constructors. These two raises are the largest in cross-section yet completed by full-face upreaming, and the success of this project is expected to increase the application of raise-boring to coal mine shaft construction. WHY 6.17 M (20 FT) DIAMETER ? Raise boring is well accepted in the metal mining industry for a variety of applications, and is gaining in acceptance in the civil works construction industry. The use of raise boring to construct vertical openings for coal mines has not been as widely accepted, even though coal mining requires, per mine, the greatest number of openings to the surface of any underground activity. Several factors have influenced the low utilization of raise boring in coal mining: 1. Coal mine shafts must often be of large diameter to pass the required high volumes of ventilation air at acceptably low water gage pressures. Cross-sectional areas of finished shafts exceeding 23.23 sq m (250 sq ft) are common. 2. The life of ventilation shafts is comparatively long, and the typical sedimentary strata overlying coal seams normally require that the shafts be lined. Shafts on the intake ventilation circuit must have permanent water-tight linings. 3. Unconsolidated overburden at the surface is often thick, and as reaming cannot be safely utilized in unconsolidated material,

Jan 1, 1979

By J. N. Adamson

The Alcan Smelter project at Lynemouth on the Northumbrian coast draws cooling water for the power station through shafts and tunnels from the North Sea. The sea at this part of the coast is frequently very rough and even in calm weather the coastal currents are strong. The adjacent coal mine makes use of these currents to disperse colliery waste and discharges into the sea some thirty thousand tons each week. In consequence the sea bed is continuously shifting and the sea is black and turbid. Construction of sea shafts under these conditions presents difficulties as drilling from a floating vessel is hazardous and sea bed activity of divers is greatly hindered by the entire absence of visibility. After considering several alternatives a method of construction was agreed with the Consultants in which the drilling and also the lining of the shaft would be completed in sequence from an eight legged work barge (GEM 126). Each shaft would be drilled to full depth and a steel cylinder, with its ends closed temporarily, would be lowered into the hole and grouted into the formation to form a full-length permanent lining. The bell mouth for each shaft would be constructed in advance to form part of the cylindrical casing. On interception of the shaft by its appropriate tunnel the lower end of the cylindrical casing would be cut away and the internal walling of the shaft installed from below. After completion of construction the shafts and tunnels would be flooded and the bell mouth sealing covers removed by divers.

Jan 1, 1997

In 1990, US mine production of barite increased 54.1 %. Barite consumption, sold or used by grinding plants, increased by 27.6%. Imports were about the same as 1989. World mine production in¬creased 12.3%, according to the US Bureau of Mines. The value of domestically produced barite, fob mine, decreased 12.7%, according to the Bureau. The declared value, cif US port, of all imported crude barite during the year 1990 increased from $40.27/t ($36.54 per st) in 1989 to $40.61/t ($36.84 per st). Nevada continued to be the leading producer of barite with 82% of the total, followed by Georgia and Missouri. It is estimated that 750/c, of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 25% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Tennessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 90% was used in drilling fluids and 10% in the non-oilfield sector. This includes barium chemicals and fillers in paper, plastics, and glass. Tonnage consumed in the drilling fluids market increased due to the higher average rig count during 1990. The average number of rotary rigs operating, (1010), was 16.2% more than the 1989 average of 869 in the US.

Jan 1, 1991

By P. Aparicio

The rheological properties of five kaolins, isostatically pressurized at 4 x10 Pa for 10 min in the presence/absence of water, was determined. Under dry conditions, measured viscosity values either decreased or remained the same. After treatment under wet conditions, measured viscosity values were 30-60% higher at high shear and 50-60% higher at low shear. These results correlate with variations in nanomorphology and structural order. Dry compaction degraded kaolinite crystals but wet-pressing appeared to cause an increase in the proportion of euhedral crystallites and a decrease in deformed crystals. Dry compaction decreased the low-defect phase proportion (ldp), but in contrast, the ldp in wet-treated kaolins remained constant or increased. Results show that hydrous pressure treatment produces a change in viscosity of kaolin suspensions, yielding the potential for improving paper coating performance, whereas anhydrous pressure treatment decreased or maintained the viscosity.

Jan 1, 2010

The transfer of Langmuir-Blodgett (LB) monolayers of collector molecules to the surface of mineral crystals is an excellent method for the study of collector adsorption phenomena and is of particular significance in the understanding and development of improved flotation separations. The fatty acid/fluorite and amine/sylvite potation systems were investigated by the Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS) examination of transferred LB monolayers of collector molecules at the surfaces of the mineral crystals. The [ir]-A isotherm study of fatty acid and amine, typical anionic and cationic collectors, showed the different packing trends dependent upon the pH and/or type of subphase. This result clearly reflects the effect of pH on compound formation and dissociation of the collector molecules. Identification of the collector adsorption state and confirmation of the validity of the FT-IR/IRS adsorption density equation were included in this research effort. This allowed for a detailed discussion of collector adsorption phenomena. As a result of these experiments, it is possible to relate the hydrophobic character of a surface to the nature of the adsorbed collector structure and thus describe flotation behavior in greater detail. For example, it appears that in the case of oleate/ fluorite the equivalent of an LB monolayer can form spontaneously during adsorption from solution, and this structure is known as a self-assembled monolayer (SAM). Such a state is significantly more hydrophobic than the oleate structure which forms on the calcite surface at an equivalent adsorption density.

Jan 1, 1996

By Ian J. Duckworth, Pierre F. X. Mousset-Jones

A detailed heat flow project was conducted at the Homestake Mine in Lead, South Dakota. This paper presents results obtained from a stope sensor system installed in the mine. The design and installation of the system are described in detail in a previous paper (Duckworth et al., 1992). The major project objective was the construction of a comprehensive heat flow data base to allow the design and testing of a new climate prediction model applicable to irregularly shaped underground excavations in non-homogeneous surrounding rock types. A mechanized cut-and-fill (MCF) stope contributes a substantial overall heat source in a mine, and the effect of this source on the working environment must be considered when planning future ventilation and refrigeration requirements. The relative magnitudes of the component heat sources encountered with the MCF mining technique are presented, having been computed from actual stope beat flow data collected over a one-month study period. The percentage of the overall heat load that is removed from the scope for each component heat sink is evaluated, and the overall energy balance is analyzed. A one-month study length was considered a sufficient period of time to allow stope monitoring for a complete range of mining conditions.

Jan 1, 1993

By T. Foster

The continuous operation of decanters in the mining industry relies heavily on the use of synthetic flocculants. Today, as plants seek to lower production costs by increasing throughput it is necessary to obtain optimum performance from the flocculant. Factors affecting such optimization include charge and molecular weight selection, and efficiency of mixing the highly viscous polymer solution with the feed slurry. Beyond maximizing dilution of the solution, the last factor is often ignored. This paper describes a series of calculations, based on fundamental transport theories, that have been used to describe flow conditions within decanter feed wells and to help select flocculant addition points. Examples are shown for the case of hydroxamated polyacrylamide flocculants in the Bayer Process, where proper selection of the addition points can result in lower flocculant dosage and better control of the decanters.

Jan 1, 1996

By George J. Dvorznak, Robert W. Waytulonis

The Bureau of Mines is conducting a research project in cooperation with the Mine Safety and Health Administration (MSHA). Mining companies, and equipment manufacturers are also participating through the Colorado Mining Association (CMA). The objectives of this cooperative research project are to determine the practicality of coupling a dry exhaust conditioning system (dry system) and diesel particulate filter (DPF) to make an integrated control system, and to determine the effectiveness and durability of the integrated system in an underground coal mine. Diesel-powered mining machines must be equipped with control devices to reduce surface and exhaust temperatures to safe levels and prevent flames and sparks from being emitted to the mine atmosphere. Diesel exhaust-gas water scrubbers have been successfully used for many years but they have several disadvantages; they are large, consume large quantities of water, and require frequent maintenance to remain functional. Additionally, diesel exhaust is a source of noxious gases and particulate matter. Particulate emissions are composed primarily of small carbon particles with absorbed hydrocarbons and they are almost entirely respirable in size. Even an engine in good mechanical condition can emit up to 400 mg/cu m of respirable particulate matter. A dry system for control of diesel fire and explosion hazards, coupled to a DPF, promises to be a complete control system for diesel engines. The dry system cools the exhaust and suppresses sparks and flame with a heat exchanger and flame and spark traps. The conditioner is smaller, consumes no water, and requires less maintenance than a comparable water scrubber. The DPF uses a ceramic substrate as a wall-flow filter and is very efficient at collecting exhaust particles. Average particulate mass collection efficiency is 90%. This report describes a cooperative research project to combine the dry system with the DPF, conduct performance tests on the integrated system at Bureau and MSHA 1aboratory facilities, and conduct field tests of the system on a production machine in an underground coal mine.

Jan 1, 1987

By P. Oghazi

It is possible to have traceability in the mining industry, by parameters and signatures like particle mineralogy, mineral association, texture and mineral liberation. The study is on an apatite-iron ore deposit at Malmberget, Sweden, and characterizes an ore body both mineralogically and texturally in a quantitative manner by using analytical methods like optical microscopy, microprobe (EMPA) and an automatic SEM based system, Particle Texture Analysis (PTA). The mineralogy was evaluated by PTA and characterized by modal mineralogy, mineral liberation and mineral associations. Magnetite has a simple outline and straight grain boundaries and the gangue minerals have a finer particle size with a more complicated texture. The PTA analysis also shows that apatite is associated to magnetite as mixed particles, while smaller grains of magnetite are inclusions in feldspar. Result from particle texture analysis shows that there is a connection which link to the mine-to-mill context, and it may be used to create traceability. This link is not the associations of the main ore mineral magnetite, nor the modal mineralogy. Instead, it is the mineral associations of contaminating minerals (apatite and feldspar) that appear to be most promising since they survive from mine to mill. The modal mineralogy may be used to understand how contaminated minerals break into or out of particles size fraction during grinding.

Jan 1, 2010