Search Documents

By A. D. Paul, Yoon R. H., C. I. Basilio

Considerable amounts of Fe3+ ions are released into solution when coal is exposed to 1-3 M acid solutions. These ions superficially oxidize the coal surface, and are reduced to Fe2+ ions. When provisions are made to generate the Fe3+ ions in solution, e.g., by inserting an anode whose potential is above the reversible potential for the Fe3+/Fe2+ couple, considerable amounts of mineral matter are liberated from the coal matrix. With many eastern U.S. bituminous coals, this mineral liberation is achieved selectively without significant breakage of the coal. It is believed that this process is induced by the osmotic pressure set-up in the crevices between the mineral matter and coal that are exposed to the solution. A theoretical model predicting the osmotic pressure is presented in this work, along with some results obtained with different coal samples.

Jan 1, 1992

By Britta Schoesser, Zdenek Zizka, Markus Thewes

"The support pressure of a slurry shield corresponds to the in situ earth and groundwater pressure to ensure the stability of the tunnel face. The support fluid (bentonite suspension) penetrates from the excavation chamber into the pore space and transfers the support pressure to the granular structure of the soil within this zone. At the same time, the cutting tools rotate periodically with the cutting wheel and remove the penetrated soil up to a certain cutting depth at the face. Shortly after the tool passing, the penetration process starts again. Both, the support pressure and the soil excavation, act in the same direction at the tunnel face, but they are subject to different cyclic intervals. This relationship between the time needed for the transient penetration process and the interval of the cyclic passage of the cutting tools at a local point at the face is examined and the impact onto the global face stability is discussed. INTRODUCTION Slurry shields are usually deployed for excavations in soft ground. The main application range is in non-cohesive soils (DAUB Recommendations 2010). In non-cohesive granular soils, the tunnel face stability is one of the key design issues. The slurry shields make use of pressurized bentonite suspension (slurry) to support the unstable tunnel face. To support the tunnel face effectively, the slurry pressure has not only to counter the groundwater pressure, but also has to be transferred into an effective stress to support the soil grains. In general, the pressure transfer can be achieved in two ways: (1) with a thin flexible membrane or (2) a penetration zone. The membrane (1), called filter cake, creates a thin impermeable layer from bentonite particles directly on the tunnel face, and enables a transformation of excess slurry pressure into effective stress. In case of penetration zone formation (2), the excess slurry pressure is transferred onto the soil skeleton along the entire penetration depth by shear stresses between slurry and soil grains. These theories, presently applied to assess the pressure transfer on the grains within slurry shield tunnelling, are originating from diaphragm wall technology, e.g. Müller-Kirchenbauer (1977), Kilchert and Karstedt (1984). They assume that the support pressure transfer mechanism is built-up instantaneously on the whole tunnel face and is not damaged or influenced by the interaction with excavation tools. These assumptions are valid for conditions during the excavation of diaphragm wall trenches whose bottom is excavated and the walls of the trench are supported. At the tunnel face of a slurry shield, the support suspension acts on the same area as the soil excavation. Hence, the conditions on the tunnel face are transient (time dependent) due to the time period needed for the penetration process of the slurry and the periodical damage of the pressure transfer mechanism by excavation tools (Fig. 1a)."

Jan 1, 2016

By Wenhua Li, Tsuyoshi Adachi

Resource nationalism is essentially mandatory government intervention in natural resources businesses by political or economic means in order to benefit the nation and the people. It is attacking the mining industry more and more rampantly by all kinds of means since the twenty-first century. Poor countries who count on a resource-led economic growth usually find themselves trapped into “resource curse”. The harmfulness of resource nationalism for investors is that one event can quickly escalate and lead to a chain of events which make projects commercially unavailable. In spite of historical and theoretical social investigations in the causes of resource nationalism, rare studies engaged in quantification of dominant parameters of it. The objective of this study is to find significant factors that dominate the occurrence of resource nationalism for important metal and energy resources producing countries and quantify their marginal effects. The study applies binary choice logit model for panel data using pooled method. One feature of the research is that binary data set of occurrence of resource nationalism are sorted out by authors referencing U.S. Geological Survey’s reports. The results indicate that high-technology export (% manufactured export), ores and metals exports (% merchandise exports), rule of law (world governance indicator), trade (% GDP), and natural resource rent except forest (% GDP ) dominant the occurrence of resource nationalism for high and upper middle income group countries; government effectiveness (world governance indicator), policy perception index (The Fraser Institute), high-technology export (% manufactured export), and mineral rent (% GDP) dominant the occurrence of resource nationalism for lower middle and low income countries. According to our model, probability of occurrence of resource nationalism in 90 countries are predicted. Top 10 risky countries in 2012 are estimated to be North Korea, India, Honduras, Indonesia, Kazakhstan, Burkina Faso, Mongolia, Cuba, Bolivia, and Peru. The study is a primary trial of researching on resource nationalism and provides some insights for theoretical building and simulation on the issue.

Jan 1, 2017

By Patrick J. Ryan, Johann F. Kerl, Angelos N. Findikakis

Introduction Tailings disposal methods used by the mining industry include the use of on-land impoundments, surface and underground mine backfill and marine disposal. The latter method, where applicable and under certain circumstances, can be the most economical and best environmental option. The term marine disposal is used to describe deposition of tailings in the open ocean, coastal waters, fjords and inland lakes. A major element in planning and designing a marine outfall is the assessment of its potential environmental impacts. The nature of the disposed tailings, and the physical, chemical, and biological characteristics of the receiving water body must be carefully assessed prior to deciding whether marine disposal is an acceptable option for a particular project. During the last decade, the North American mining industry has demonstrated a commitment to studying potential adverse environmental impacts of marine tailings disposal and to continue monitoring of the receiving waters. Extensive monitoring programs have been undertaken by Canadian mines. Marine tailings disposal is not used in the United States today. One of the largest U.S. mines proposing to use this option is the Quartz Hill mine of U.S. Borax in Southeastern Alaska. To assure the regulatory agencies and the public of the viability and acceptability of this option, U.S. Borax undertook an extensive program of environmental studies aimed at assessing the impact of marine tailings disposal. This program was part of the feasibility and environmental permitting studies conducted by Bechtel Civil & Minerals, Inc, on behalf of U.S. Borax. Due to the unique nature of the proposed tailings disposal system, a Board of Consultants was established. The Board assisted in planning the modeling and field program and reviewed ongoing work. This paper outlines the basic elements of the marine tailings disposal study program which can be viewed as a prototype for similar studies elsewhere. Background The Quartz Hill molybdenum deposit is located on a knoll in an elevated valley in a mountainous region of southeast Alaska, about 45 miles east of Ketchikan (Figure 1).

Jan 1, 1986

By R. Y. Wan, Corby G. Anderson, L. Ernest Krys, M. C. Fuerstenau

Since 1942, refractory precious metal concentrates at the Sunshine mine have been processed for antimony metal recovery using a novel leach-electrowin method. This is counter to most antimony production facilities where pyrometallurgical techniques are usually relied upon. The key step for removal of the antimony has been an ambient pressure alkaline sulfide leach. In 1990, a comprehensive laboratory study was undertaken to better understand this process. Factors studied included temperature, agitation, concentrate regrind, alkaline species concentrations, sulfur species concentrations and solids concentration. Details of these studies, as well as a brief description of Sunshine metallurgical processes, will be presented.

Jan 1, 1993

By M. U. Khan

"Underground mine diesel equipment generally offers more flexibility as compared to electric powered systems. Diesel exhaust is an adverse agent which affects the health of underground miners. The National Institute of Occupational Safety and Health (NIOSH) regard diesel exhaust as carcinogenic. The NIOSH 5040 method is an established technique for measuring Diesel Particulate Matter (DPM). This process inherently involve a lag time before an accurate exposure determination can be made during which miners are potentially overexposed to DPM. This issue can be addressed by using realtime DPM monitors. This paper presents underground mine shift average based and realtime monitored DPM values monitored in US mines. A FLIR Airtec instrument has been used for realtime measurement whereas shift average based DPM has been determined by the use of NIOSH 5040 method. A log of diesel equipment movement was kept. DPM concentrations versus time were plotted and analyzed. High DPM sources were identified and the FLIR Airtec was demonstrated to be satisfactory for realtime DPM measurements. INTRODUCTION The use of diesel equipment in mines is an attractive option due to its ability to convert a large fraction of available energy into useable work. Diesel engines are rugged, dependable and fuel efficient. It is very common for diesel engines in heavy duty trucks to have a life of 1,600,000 km [Anon, 1999]. Generally in underground mines compared to electric powered equipment, diesel equipment provides more maneuverability. It can be assumed that the underground mining industry will maintain its reliance on diesel powered equipment keeping in mind the recent developments in other energy alternatives [Anon, 2001a]. A harmful aspect to the use of diesel as a fuel is its resultant emission as an adverse environmental exposure agent. Generally diesel particles are approximately one order of magnitude smaller than respirable dust aerosols in underground mines (typically less than one micron in size) [Kittelson, 1998]. Force of gravity has less effect on DPM due to its small particle size. The phenomenon of less gravitational attraction increases the settling and residence time of DPM in the mine atmosphere. High residence time of DPM as compared to other mechanically generated particles increases the chances of diesel particles deposition in the human respiratory tract. The small sized diesel aerosols penetrate deeply into regions of the human lung [Morawska. et al. 2005], which increase the health risks associated with long term exposure to diesel aerosols. Published studies documented the adverse health effects of DPM exposure [Walsh M.P., 1999]. Continuous and long term DPM exposure can result in respiratory disease, lung cancer, reduced lung capacity, and heart disease. NIOSH has declared that the reductions in DPM exposure would reduce cancer risks. In underground mines DPM determination is a challenging task and it is becoming a matter of serious concern due to the harmful health effects associated with the exposure of DPM. The current study involves the determination of realtime and shift averaged based DPM in underground mines of United States of America (USA). Realtime DPM was measured using FLIR Airtec monitors and shift averaged based measurement was performed by the MSHA approved NIOSH 5040 method. FLIR Airtec uses laser scattering approach to measures the Elemental Carbon (EC) component of the DPM. The results from the FLIR Airtec were compared with the results of NIOSH 5040 method and its performance was found satisfactory."

Jan 1, 2015

By Gerald H. Luttrell, Roe-Hoan Yoon

Flotation columns are becoming increasingly popular due to their ability to improve selectivity and to reduce operating costs. Unfortunately, these advantages are not often realized because of poor operating practices and difficulties associated with design and maintenance. This article provides guidelines for the operation and design of columns. The discussion will focus on designing proper wash water systems for improved selectivity, maximizing throughput by increasing the bubble surface area rate, and minimizing operating and maintenance costs. It is suggested that the design of the air sparging system is the most critical element in column flotation.

Jan 1, 1993

By S. Painter

The effects of forced ventilation and thermal radiation in open drifts are included in three-dimensional thermal hydrology simulations of a potential waste repository at Yucca Mountain, Nevada. A semi-analytical model is used to calculate the amount of waste heat removed by ventilation air during each time step of the multiphase thermal-hydrology simulator. The model accounts for thermal radiation and changes in air temperature and humidity along the emplacement drifts. The fraction of heat removed by ventilation is time and position dependent.

Jan 1, 2004

By Ditend Tesh, Godfrey Dzinomwa, Harmony K. Musiyarira

Namibia is known as water stressed country with a limited amount of fresh water. Therefore, the use of water is an important topic in the country’s development agenda. Water is a shared and finite resource, with high social, cultural, environmental and economic value. However, freshwater resources are under pressure from ore processing, industrialization, urbanization and the demands of a growing population. In Namibia, ore processing, coupled with the anticipated increase in water demand for human consumption and other uses, has created significant stress on the limited water resources of the country. This is critical in the mining industry as water remains typically the prime environmental medium (besides air) that is affected by mining activities. This study sought to investigate the strides made in water management in mining, especially in environmentally sensitive areas of Namibia. Most mining companies operate next or alongside farms, national parks and fishing areas. The overall objective of this research was to highlight the current practices in Namibia’s mineral industry operating in environmentally sensitive areas especially in areas where uranium is being mined and processed. The methodology consisted of comprehensive literature review, field visits to the case study areas, and comparative studies with best practices. This study shows that over a ten-year period, freshwater consumption was reduced by over 55% per tonne of milled ore in uranium mines, resulting in substantive financial savings as well as the delay in water augmentation through desalination. The strategies employed by the Namibian companies involve inclusive stakeholders’ engagement, recycling and reuse, and the minimization of water losses. The realization that the water challenge cannot be solved by any one party acting alone has been fundamental in ensuring environmental compliance within the mining industry in Namibia. Namibia’s industrial leaders have increasingly recognized that reducing the water footprint of mining activities must be one of the key performance indicators for management. The major finding of this study was that Namibia with its unique ecosystems, mineral reserves, and emerging industries can harness a wide range of resources both to improve the welfare of its citizens and to protect the integrity of its environment.

Jan 1, 2017

By Jean-Marie Deschamps

In an approach to the complicated study of bauxite from Les Baux de Provence it is necessary to consider the paleogeographical context of all the bauxites in southern France. These bauxites are of Karstic type, belonging to a metallogenic area extending from the Pyrenees Mountains to the Alpine Massif. Within this area each deposit does not always correspond to the same geological period. There are differing opinions regarding the origin of Karstic-type bauxite and a discussion of these various theories is beyond the scope of this paper. Bauxite of Les Baux, in Provence, was discovered in 1821 by the chemist, Berthier, near this picturesque village located in the region of Arles. It is Les Baux from which the name of bauxite originates. For a long time this bauxite was of no interest because of high silica 'and mediocre alumina content. Besides, the calcium carbonate content is somewhat high and is one of the main characteristics of Les Baux bauxite. The problem of exploration of the Les Baux deposit has been to prospect minable zones according to traditional norms where silica and carbonate are low.

Jan 1, 1977

By Khaled Morsy

Cementitious seals are made of foamed cements with strength ranging from 100 to 600 psi. These cementitious seals are usually used at locations where the seal will be subjected to some convergence, assuming that this material can absorb entry closure without compromising the structural integrity of the seal. Prior to 2006, Lake Lynn Experimental Mine (LLEM) conducted full-scale tests on various cementitious seals designed to meet or exceed the 20-psi horizontal static load requirements of the old 30 CFR1 75.335. Both hydrostatic and dynamic loading tests were conducted. The structural response (pressure and displacement readings) obtained from these tests were recorded. The stability of the cementitious seal is based on balancing the load applied to the face of the seal from the explosion against the shearing resistance at the seal/rock interface. Therefore, the properties of the seal/rock interface, such as stiffness, cohesion, friction, etc. are critical to determine the stability of a cementitious seal. These properties are usually assumed by the researchers in their models. This paper emphasizes the importance of having the correct properties of seal/rock interface in the numerical modeling. FLAC 3D models were developed to simulate Celuseal2 cementitious seals subjected to both hydrostatic and dynamic loadings. Using the hydrostatic and dynamic loading test data conducted at LLEM, the static and dynamic properties of the seal/rock interface were back calculated. The FLAC 3D models showed good agreement with the test results.

Jan 1, 2009

By C. P. Shen, H. C. Tsai, Bennie Chu, Y. S. Hsieh

The Pinglin tunnels are situated within the fold-and-thrust belt structural region in Taiwan, due to continent-arc collision and plate tectonic setting. The pilot tunnel TBM (§=4.8m) became stuck ten times with the standstills to date. The westbound main tunnel TBM (§=11.74m) was buried in a collapsing calamity. The main tunnel TBM shall identify and overcome the adverse geology with high volume of ground water ingress itself. This paper presents our experience and methodology through the adverse geology with Pinglin large TBM.

Jan 1, 1999

By George J. Allen, Laura A. Allen

Introduction This section of the text presents a general review of the different types of concentrate marketing contracts. Too often the marketing strategy is ignored in the design phase of the project and the producer is left to the mercy of the buyer. Many items such as concentrate grade, impurity levels and moisture content of the concentrate my enhance, or severely restrict the producers ability to make a profit it. Close attention should be paid to the design of the concentrator which can improve the quality of the concentrates, thus the ability to increase the rider of potential buyers can be enhanced. Difficult at best, is the position of the miner who only has one outlet available for its production. Obviously, the trade offs must be evaluated. For example, concentrate grade vs recovery and grind/filtering capacity vs moisture of the concentrate all must be weighted against freight cost to a potential buyer. In addition, the above considerations must be weighed against the capital cost to the miner. This chapter is intended to highlight important articles that are included in short and long term agreements and to give a new miner/producer some insight into hat my or my not add value to the product. Unless the miner sells the product directly to a consumer such as a gold, or silver producer, or to a large enough operation that has a totally intergrated system to make a finished product, most miners are forced to sell to buyers who ultimately will refine and market the product. Types of Contract Agreements There are many types of contract agreements just as there are colors in the rainbow, however, most contracts fall into three basic categories. (1) Smelter Schedules: Designed for the small producer, the odd lot of concentrate, smelter flux and precious metal ore. Albeit custom smelters are becoming fever by the day, because of pollution control requirements and financial difficulties, most remaining custom smelters have a smelter schedule. A smelter schedule is a posted list of charges and conditions that the smelter will buy material from a seller. Smelter schedules exist for copper, lead, zinc, silver and gold (Handbook for Small Mining Enterprises, Montana Bureau of Mines). (2) Short Term Custom Contracts: Large mine producers frequently use Short Term Contracts where the seller has the buyer frame a contract that is tailored to the sellers’ production. The short term contract my be as long as one year. A spot sale qualifes as a

Jan 1, 1986

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

The purpose of this work is to develop a conceptual recovery process for thorium dioxide (ThO2) from its primary source, monazite. The study-level design presented in this paper represents an economically viable method for conducting ThO2 extraction from monazite ore while also recovering byproducts that include P2O5 and other rare earth element oxides rather than producing unnecessary waste streams. Three key points to note in the development of this process design are: (1) the process economics relied heavily on recovery of rare earth byproducts, (2) the thorium handling portions of the process could effectively be segregated from the rare earth and phosphate handling portions of the process, and (3) the thorium and uranium content in waste streams should be carefully managed and eliminated where possible.

By Louis J. Jansen, D. E. Ranta

Techniques utilized to incorporate geological data in computer modeling and ore reserve estimation have undergone considerable evolution during the past fifteen years. Computer analysis and evaluation of two precious metal deposits are presented as examples of innovative computer techniques developed at Asarco. The first is a gold deposit occurring in a steeply dipping Precambrian greens tone sequence. The second is a manto-like manganiferous silver deposit occurring in a relatively flat sequence of Late-Paleozoic sediments. In both deposits, four sub-horizontal zones of geological influence are evaluated.

Jan 1, 1992

By V. R. Manukonda, I. Iwasaki

Selective flocculation of iron ores is extremely sensitive to the type and amount of soluble salts in pulp solutions. Chemical precipitation of alkaline earth ions combined with ultrasonic treatment deactivates their adverse effects without using any environmentally ill-defined reagents. The manner in which ultrasonic treatment affects starch adsorption on hematite, dissolution of quartz, and the selective flocculation process was investigated. Selective flocculation tests were conducted in the presence of up to 400 ppm calcium ion on a quartz-hematite mixture by precipitation as calcium carbonate, and the role that silicate ion generated by ultrasonic treatment plays in achieving the selectivity of separation is discussed.

Jan 1, 1988

By Yannis Faitakis, Brenda M. Wright, Gail Powley, Mark Hamblin, Randy B. Paine

A major problem in the ore extraction process is the high degree of variation in the mix of materials that make up the mined ore. The mix of materials makes it extremely difficult to characterize and predict the behavior of the ore when it is processed. The Quality Production Database (QPD) tool was successfully used in order to predict and transfer information regarding the quality characteristics of the ore being delivered to the extraction and hydrotransport unit operators. This paper describes the use of QPD in the prediction of various ore characteristics at the Syncrude Canada Ltd. processing facility.

Jan 1, 2000

By Y. C. Kim

To generate a most profitable, ultimate pit limit is generally the first step in mine design. This paper presents a new graph theory oriented, optimum ultimate pit limit design algorithm which will maximize the total undiscounted net profit. This algorithm performs much better than the well known Lerchs-Grossmann algorithm, in terms of the reduction in computation time and computer memory requirements. This algorithm operates on many directed trees in a graph, where each vertex in a tree represents a block in the mine model. The formation of each directed tree is based more on the ore-waste support concept than the geometry constraints alone. The general procedures of the algorithm, programming considerations and two case study results are discussed in the paper.

Jan 1, 1992

By T. D. Murphy

In the fall of 1988 it became evident that the accuracy of sulfur forecasts for Monterey Coal's No.1 Mine needed to be improved. In addition, it became necessary to predict if any individual train shipments during a month would exceed a contract sulfur limit. The challenge was to develop a forecasting process that would take into account the variability of the coal in the ground as well as the difference between laboratory and preparation plant sulfur reduction efficiency, and the effects of mining coal with multiple units. This paper describes how geostatistics and simulation techniques were used to meet this challenge.

Jan 1, 1992

By T. E. Bernard

"Refuge alternatives (RA) provide shelter to miners trapped underground during a disaster. RA manufacturers must demonstrate that their RAs meet the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and the management of heat that results from the RA occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements, and carbon dioxide generation that is representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current US coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in an RA. The highest likely metabolic heat generation ranged from 115 W to 135 W, depending on RA occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 LO2/h/person (0.81 ft3/h/person) and 20 LCO2/h/person (0.71 ft3/h/person), which means the margin of safety is 50% or more when compared to the MSHA requirements. INTRODUCTION Refuge alternatives (RAs) provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their RAs meet Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen, the removal of carbon dioxide, and the management of heat that results from the occupants and the mechanical/chemical systems in the RA [1]. These MSHA requirements were based on a standard 70 kg (168 lb) male with an assumed allocation of activity of 80% rest and 20% moderate activity level [2]. The purpose of this paper is to re-examine the metabolic heat generation and oxygen and carbon dioxide requirements of miners in an RA based on actual miner size and more realistic RA activity levels based on current RA designs. The purpose of this paper is to re-examine the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and heat generation. To achieve this, researchers took the following steps to estimate the metabolic demands and the associated heat generation, oxygen requirements, and carbon dioxide production. 1. Characterized the anthropometric characteristics of the miner population. 2. Described the metabolic rate profile of RA occupants. 3. Characterized the maintenance demands of RAs. 4. Summarized oxygen supply and carbon dioxide removal volumes. ANTHROPOMETRIC CHARACTERISTICS OF MINERS The weight, height, and age distributions of the adult male populations are summarized in Table 1. For each data set, the reported mean and standard deviation are provided. The 95th percentile (%ile) value for height and weight for each population was the mean plus 1.64 times the standard deviation."

Jan 1, 2017