Search Documents

By E. Tabosa, S. Vianna, K. Duffy, W. Valery, B. Andrade, L. Pyle, P. Holtham

Pneumatic flotation cells are high-intensity flotation machines with rapid kinetics, resulting in short residence times. Examples include the Jameson, PneuFlot and ImhoFlot cells. These cells do not use impeller-like mechanical cells. Rather, the air and pulp are mixed in a continuous stream of high fluid velocity through a downcomer or venturi to disperse the air into fine (approximately 0.5 mm) bubbles and maintain particle suspension. Froth wash water is often used to enhance concentrate grade, minimising recovery by entrainment. With the growing application of these types of cells, not only in cleaner stages (their traditional use) but also in pre-flotation and scalping duties, there is a need to predict their performance more accurately for circuit design and optimisation. No widely accepted model for pneumatic flotation cells is available and their metallurgical performance is often scaled up from laboratory and/or pilot plant testing by assuming fixed values for metal recovery, concentrate grade and concentrate percent solids. This paper describes a new approach to simulate pneumatic flotation cell performance and presents case studies demonstrating its applicability. Keywords: Pneumatic flotation, flotation modelling, flotation circuit design, flotation circuit optimisation, Jameson cell

Jan 1, 2020

By N. A. Chapman

The effect of using conventional crushing and HPGR in combination with dry or wet milling was investigated using a base metal sulphide (sphalerite), and a PGM (platinum group minerals) ore in order to determine how these different processes affect the flotation performance. In the case of sphalerite, irrespective of the crushing procedure (HPGR or conventional), dry milling resulted in the highest grades and recoveries of zinc. Conversely, in the case of PGMs, a similar treatment produced the poorest results. The results were investigated further by comparing the relative effects of factors such as percentage liberation, particle size, and surface properties of the samples produced by the different milling procedures as well as the concentrates and tailings obtained from the flotation tests.

Jan 1, 2013

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant oven, it was essential to ascertain coal cake stability during the loading of a 1 m3 (1 m × 1 m × 1 m) coal cake into the cold pilot-plant oven by a pusher mechanism. Previously established laboratory-scale compaction parameters, to obtain coal cakes with sufficient stability, were employed during the loading tests of the coal cakes. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.It was demonstrated that lower applied compaction forces (14%) can be utilized during 1 m3 compaction, in comparison to laboratory-scale tests, to obtain similar wet cake densities, owing to differences in the effect of frictional forces. Wet cake densities for Waterberg sscc improved slightly (3%) to 1.13 t/m3 when utilizing 79 t/m2 applied force for a 1 m3 coal cake, in comparison to laboratory-scale tests. Similar results were obtained for Oaky North hard coking coal, with a 6% density increase to 1.27 t/m3 at a similar applied force. Porosities decreased by 13% and 32% for Waterberg sscc and Oaky North coal, respectively, when 1 m3 compaction was compared to laboratory-scale tests. An opportunity exists to further decrease the porosities of Waterberg sscc during compaction, whereas acceptable compaction parameters were achieved for Oaky North hard coking coal. Most major vertical cracks and the partial collapse of coal cakes were mitigated, and high-stability coal cakes were obtained that could be successfully loaded into the pilot-plant coke oven by a pusher mechanism.Factors contributing to the instability of the coal cake during loading into the oven, such as vertical cracks, are (i) the cubic geometry (1 m3) of the coal cake, (ii) friction exerted by the oven floor, and (iii) mechanical problems, such as a misalignment between the pusher machine feeder plate and the oven floor. IntroductionOperation of the stamp-charging horizontal 1 t electrically heated coke pilot-plant oven at Exxaro Resources requires coal cake stability during the loading of a 1 m3 compacted coal cake into the oven. In this case, a pusher plate is utilized to push the coal cake into the oven over the oven floor. This is in contrast to a ‘spoon’ or bottom plate feeding mechanism as found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability for the 1 t coke oven, various compaction parameters need to be verified and established."

Apr 1, 2019

By F. Ntuli, T. V. Nyangadzayi

Chromium green is an essential metal with various applications in the paints, construction, electronics, and aerospace industries. The main source of chromium green is the carbo-thermic reduction of chromite ores, however, chromite ores are being heavily depleted on a global scale, hence the need to find alternative or secondary sources for the chromium. In order to meet the global demand for chromium there is a need to implement principles of the sustainable circular economy to keep chromium within the material loop. Ferrochrome slag and stainless steel slags are secondary resources that are potential sources of chromium. In this work, recovery of chromium from ferrochrome slag was investigated. The ferrochrome slag was alkaline leached using sodium hydroxide- sodium hypochlorite solution to reduce the use of potent reagents that have a potential negative environmental impact. The leachate produced by oxidative alkaline leaching of ferrochrome slag contained hexavalent chromium, which was used to recover the extracted chromium through a two-stage process involving reduction and precipitation. Reduction of hexavalent Cr to trivalent Cr was investigated using anhydrous FeSO4 at concentrations of 5 g/L, 10 g/L, and 15 g/L. Precipitation was conducted by dosing the reduced leach solution with 1 M sodium hydroxide at dosages of 5 ml/L, 10 ml/L, and 15 ml/L. The experiments were designed using the Taguchi (L9) orthogonal array and analysed according to the ANOVA, general linear model. The optimized conditions for the reduction step were ferrous sulfate dosage of 5 g/L with a pH of 12, and for the precipitation step, 1 M sodium hydroxide at a dosage of 15 ml/L with a setting time of 90 minutes and pH of 7. Physical changes were observed during the two-step chromium recovery, with solution changing from a yellowish colour to dark green colour indicating completion of the reaction. The chromium recovery was found to be 93.3%.

Dec 11, 2024

By t. Knezicek

Tuzla Coal Basin in Bosnia and Herzegovina is the largest coal area in the State. Regional mining industry sensed the need for mining machinery database development in order to achieve easier planning purposes and equipment selection for open cast mines in Tuzla Coal Basin. Several databases for mining machinery used on the bituminous deposits, i.e. on brown coal and lignite mines, were developed at the Faculty of Mining, Geology and Civil Engineering, Tuzla. System Development Method was used as the approach to the database development, generating relational structure of database. First database was established for trucks and was presented as simple table, drawn and filled on the paper sheet. In the next phase, data were stored in spreadsheet type software (Quattro Pro and Excel). Lately developed database is Bucket Wheel Excavator database designed in MS Access. Two concepts, spreadsheet and Access, were integrated into one large database, enabling manipulation of hundreds of data at one place. Required adaptations of existing database in MS Access, enables Access to be used as an integration resource. Database is designed to reserve free memory for input data for mining equipment not considered so far, such as spreaders, crushers, belt conveyors, tripper cars, etc. New, integrated database, at this stage, can be imported to any type of commercial or individual software where needed. Mining machinery integrated database for open cast mine operations is under going testing in a State company, Coal Mines Tuzla. Keywords: Tuzla Coal Basin, machinery database, SDM, relational database

Jan 1, 2003

Council and Standing Committees, 1977-1978 President: P. A. von Wielligh. Vice-Presidents: Dr M. G. Atmore and D. A. Viljoen. Honorary Treasurer: J. K. E. Douglas. Immediate Past President, Dr M. D. G. Salamon. Members of Council: J. D. Austin, A. N. Brown, A. A. Hazell, Dr P. R. Jochens, Prof. R. P. King, Dr D. G. Krige, Prof. F. Q. P. Leiding, D. G. Malan, J. C. Mostert, H. G. M. Rose, W. T. Ruhmer, A. A. Sealey, R. A. von Maltitz. Chairman, Witbank-Middelburg Branch: T. S. Wilmot. Chairman, Orange Free State-Klerksdorp Branch: A. N. Shand. Past Presidents Serving on Council: R. J. Adamson, H. Britten, J. K. E. Douglas, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plowman, Dr R. E. Robinson, P. W. J. van Rensburg. Standing Committee Chairmen: Membership, D. A. Vil¬joen; Technical Programme - Metallurgy, Dr P. R. Jochens ; Technical Programme - Mining, Dr D. K. Krige ; Vacation School - Metallurgy, Prof. R. P. King ; Vacation School - Mining, Dr M. D. G. Salamon; Awards, Dr M. D. G. Salamon; Excursions, Dr M. G. Atmore; Adjudication, Dr M. D. G. Salamon; Consti¬tution, Rules, and Policy, Dr M. D. G. Salamon; Mines and Works, P. A. von Wielligh ; Education, Dr M. D. G. Salamon; Monograph Series, Dr R. E. Robinson; Phoenix National Committee, Dr R. E. Robinson ; Pyrometallurgical Discussion Group Convenor, Dr J. B. See/Dr D. I. Ossin.

Jan 1, 1979

By S. Khoshjavan

In this investigation, the effects of different coal chemical properties were studied to estimate the coal Hardgrove Grindability Index (HGI) values index. An artificial neural network (ANN) method for 300 data-sets was used for evaluating the HGI values. Ten input parameters were used, and the outputs of the models were compared in order to select the best model for this study. A threelayer ANN was found to be optimum with architecture of five neurons in each of the first and second hidden layers, and one neuron in the output layer. The correlation coefficients (R2) for the training and test data were 0.962 and 0.82 respectively. Sensitivity analysis showed that volatile material, carbon, hydrogen, Btu, nitrogen, and fixed carbon (all on a dry basis) have the greatest effect on HGI, and moisture, oxygen (dry), ash (dry), and total sulphur (dry) the least effect. Keywords coal chemical properties, Hardgrove Grindability Index, artificial neural network, back-propagation neural network.

Jun 1, 2013

By W. Guiye, L. Chongjun, L. Huinan, Z. Yangge, H. Long

The current application of copper-molybdenum (Cu-Mo) separation inhibitors is often associated with large dosage, high toxicity, environmental pollution problems. In order to solve these problems, a light sensitive Cu-Mo separation inhibitor LS（light sensitive inhibitor，abbreviated to LS） was developed. In this paper, inhibitory performance, photodegradation rule, and acting mechanism of LS were studied. The subsequent test results showed that, compared with traditional inhibitors, LS has shown comparative advantages, with lower dosage and good inhibiting effect. A series of flotation tests with LS as inhibitor were conducted on a Cu-Mo concentrate. A locked-cycle test showed that a molybdenum concentrate containing Mo 49.88% and Cu 0.6%, with 93.23% molybdenum recovery and a copper concentrate containing Cu 29.92%, with 99.99% copper recovery can be obtained. The photodegradation performance of the reagent was investigated under 365 nm, 254 nm and sunlight irradiation. The degradation of the reagents could be completely achieved by irradiation of three wavelengths of light. However, with the different wavelength of irradiation light, the degradation rate is different, the time required to reach 50% degradation rate being 3 h (254nm), 4 h (solar light) and 6 h (365nm) respectively. The inhibition mechanism on chalcopyrite was studied. FTIR study showed that LS could be adsorbed on the surface of chalcopyrite by chemical adsorption, which could enhance the hydrophilicity of chalcopyrite. Ultraviolet adsorption tests indicated that the adsorption capacity of LS on chalcopyrite surface was greatly affected by pulp pH value, and the proper pH value was 5-9. Keywords: Copper-molybdenum separation, Inhibitor, Light-sensitive, Photodegradation, Mechanism.

Jan 1, 2020

By R. V. Ramani, R. Stefanko

"The favorable mining conditions in the United States of America that resulted in the development of the highly productive room and pillar systems are largely disappearing. Increasing mechanization, poorer natural conditions, and greater concern for health, safety and environment gave impetus to the enactment of the Federal Coal Mine Health and Safety Act of 1969. These regulations prescribe more stringent requirements in face ventilation and mine air distribution, necessitating significant changes in existing ventilation systems. Stringent mandatory standards were applied to respirable dust control for the first time, and simultaneous control of both gas and dust has affected the face as well as primary distribution, most notably on haulage entries.The size and complexity of the present-day mining operations, and the need to evaluate various system changes in a limited time, call for scientific methods in mine planning. In this paper, the authors trace the previous applications of computers to mine ventilation planning and discuss the results of their work in applying a ventilation simulator developed at Penn State. The paper includes an analysis of current trends and suggestions for future research and development."

Jan 1, 2014

By Z. Zhang, J. Niu, H. Wang, Y. Xu, J. Shi

Tribo-electrostatic separation is a promising method for effectively utiliing low-grade magnesite resources by removing quartz and improving the grade of magnesite. To determine the chargeto- mass ratios of pure magnesite and quartz, a triboelectric measurement system was employed, and a laboratory tribo-electrostatic separation system was used to separate low-grade magnesite. The results showed that the maximum difference in charge-to-mass ratio between pure magnesite and quartz particles was observed after friction with polyvinyl chloride. The grade and recovery of magnesite increased with temperature and initially increased with increasing voltage, feed rate, and air flowrate before gradually decreasing. The optimal conditions resulted in a concentrate with 46.91% MgO content and 77.36% recovery, while the quartz content decreased from 7.02% to 1.95%. These experimental results demonstrate the effectiveness and potential of tribo-electrostatic separation in removing quartz and upgrading magnesite.

Apr 14, 2024

By Y. G. Zhu, G. B. Zheng, X. X. Hu

Reverse flotation by cationic collectors is the classical method to reduce the silicon content in magnesite. But because of the low selectivity, there is a large loss of magnesite in the reverse flotation froth. To improve the efficiency of the collector, a novel collector named BK433 was developed in this paper. In order to determine the performance of the BK433 collector, a systematic experimental study was carried out with a high silicon magnesite in China. The suitable pH environment of slurry was confirmed, the depression effect of different depressants was investigated, and the flotation effect was compared with commonly used traditional collectors. The results show that the BK433 shows remarkable good selectivity and collection ability. After the 4 stages reverse flotation, the SiO2 content decreased from 3.76% to 0.25%, SiO2 impurity removal rate reached 94.69%. Meanwhile, the MgO content increased from 45.06% to 46.73%，the recovery of obtained concentrate (calculated by MgO) was 82.79%. Keywords: Magnesite, Desilicication, Reverse flotation, Collector

Jan 1, 2020

By B. Moritz, W. Schubert, E. A. Button

ABSTRACT: Geological conditions associated with alpine environments in combination with high overburden in many tunnelling projects lead to squeezing behaviour. The main problems associated with such conditions include large deformations, overstressing of supports, and lack of face stability. In the past during Alpine tunnelling the problem of large displacements incompatible with rockbolt – shotcrete support systems have been solved by leaving gaps in the lining to accommodate excessive deformations. In the late nineties, yielding elements have been developed, which are integrated into the lining. The paper deals with the basic concept, the design and the application of that system, which has been successfully used in several Alpine tunnels. ZUSAMMENFASSUNG: Die geologischen Verhältnisse in den Alpen führen bei großer Überlagerung häufig zu starken Deformationen während des Baues von Tunneln. Die großen Verformungen führen in vielen Fällen zu einer Überbeanspruchung des Ausbaues und Problemen mit der Ortsbruststabilität. Früher ist man dem Problem der Unverträglichkeit des Ausbaues mit den hohen Dehnungen durch Freilassen von Deformationschlitzen im Spritzbeton begegnet. Vor etwa 10 Jahren wurden duktile Stahlelemente entwickelt, welche in die Spritzbetonschale integriert werden. Der Beitrag beschäftigt sich mit dem Konzept, der Planung und der Ausführung. RÉSUMÉ: Les conditions géologiques dans les Alpes conduisent fréquemment lors d'un grand recouvrement à des déformations fortes pendant la construction des tunnels. Les grandes déformations conduisent dans beaucoup de cas à une surtension du revêtement et à des problèmes avec la stabilité de front de taille. On a fait face plus tôt au problème de l'incompatibilité du revêtement avec les extensions élevées par libérer des rainures dans le béton projeté. Il y a environ 10 ans, des éléments sidérurgiques ductiles qui sont intégrés dans le béton projeté ont été développés. La contribution s'occupe de concept, de planification et de mise en oeuvre.

Jan 1, 2003

By L. Zhang, Y. Zhou, H. Wang, C. Mo

Fluorination of magnetite (Fe₃O₄) by NH₄HF₂ was investigated using simultaneous thermogravimetry and differential thermal analysis (TG-DTA), and observing the morphology and phase changes using scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) and X-ray diffractometry (XRD). The results indicate that fluorination with the involvement of oxygen begins at room temperature, peaks at 178.40C, and is completed at 2000C with the formation of only (NH₄)₃FeF₆. On heating, (NH₄)₃FeF₆ gradually releases NH₄F by the formation of NH₄FeF₄ at 2590C, then (NH₄)0.18FeF₃ at 3270C, and finally FeF₃ with minor FeF₂ at 4000C due to the partial reduction of Fe (III) to Fe (II). At 5500C, FeF₃ is oxidized to FeOF/Fe₂O₃.

Dec 13, 2022

By I. Mc Dougall

Water-cooled copper tap-hole blocks provide an effective means of extending the life of tap-hole refractories, as the lower temperature of the refractory material inhibits wear and other damage and promotes the formation of a protective frozen slag layer. This is particularly beneficial during prolonged tapping cycles. The copper block forms an integral part of the lining, and provides mechanical support to the refractory, facilitating rapid replacement of tapping channel bricks without disturbing the surrounding lining. Safety considerations are an important design factor, and the positioning of the water channels is optimized to prevent leaks although the copper is not in direct contact with the molten fluids during normal operation. Water-cooled copper blocks designed by Tenova Pyromet have successfully been utilized on metal, matte, and slag tap-holes for a number of processes, including nickel, platinum group metals, and mineral wool.

Jan 1, 2014

By A. Adeli, A. V. Metcalfe, E. Addo, E. Sepulveda

"The accurate modelling of geometallurgical data can significantly improve decision-making and help optimize mining operations. This case study compares models for predicting copper recovery from three indirect test measurements that are typically available, to avoid the cost of direct measurement of recovery. Geometallurgical data from 930 drill core samples, with an average length of 19 m, from an orebody in South America have been analysed. The data includes copper recovery and the results of three other tests: Bond mill index test; resistance to abrasion and breakage index; and semi-autogenous grinding power index test. A genetic algorithm is used to impute missing data at some locations so as to make use of all 930 samples. The distribution of the variables is modelled with D-vine copula and predictions of copper recovery are compared with those from regressions fitted by ordinary least squares and generalized least squares. The D-vine copula model had the least mean absolute error. IntroductionIn this paper we compare the use of D-vine copula, generalized least squares (GLS), and ordinary least squares (OLS) for modelling geometallurgical data from an orebody in South America. The first objective is to construct models for predicting copper recovery (Rec) from the Bond mill index test (BWi); resistance to abrasion and breakage index (A*b); and semi-autogenous grinding (SAG) power index test (Spi). This involves fitting a D-vine copula and regression models fitted by OLS and GLS. The second objective is to investigate the performance of the fitted models for predicting Rec (Willmott and Matsuura 2005).Traditional resource model approaches either ignore the mineral processing characteristics of extracted tonnages or treat processing as an independent component of a mining operation. The net present value (or any other objective) can be truly optimized only by considering the mining operation as an integrated system in which net value is defined as the end-product that the company sells. This approach requires the resource model to be extended to include all relevant rock properties and processing responses."

Mar 1, 2019

By Christopher J. Oates

Overview ? Mining Codes ? Best Practice ? Mining Standards Guidelines ? Get it right from the start ? External Auditors ? The 5% rule ? MMCRM's - The Key Components ? The MMCRM Report / Certificate ? MMCRM's & Round Robins ? Summary

Jan 1, 2005

By D. Hanekom

Over the past couple of years, Anglo Platinum has made extensive use of technology within the core disciplines (geology, evaluation, survey, and planning) that collectively form part of mineral resource management (MRM). While these technologies were primarily developed to enable geology, evaluation, survey, and planning to carry out their daily tasks, with the main objective of supporting the mine?s production effort, they have also enhanced the disciplines? ability to produce the required outputs within the annual business planning cycle. Anglo Platinum has developed a very comprehensive business planning process, and these technologies play a vital role in enabling both the quality and quantity of inputs into the process, and also the value-add of the final product. This prompted a question regarding the practical application of the CADSMine software. If we changed our thinking in how we applied the software, would it be possible to further improve on the time taken to deliver a business plan? In changing the current planning approach, would we be able to further simplify the process? Is there a way to reduce the data generated in order to enhance the time taken to do reporting, as the CADSMine software is totally network dependent? Less data should equal faster reporting. This paper focuses on the practical application of the CADSMine software, and demonstrates the value-add to the business planning process that can be gained if the mine design methodology is changed from individual panels to bigger blocks representing a raise line.

Jan 1, 2012

By J. de Korte, Z. Loubser

"SynopsisThe aim of a blending stockpile is to minimize the natural variation in properties of a material. Two simulation models were written, for coneshell and chevcon stacking, and used to investigate the influence of different stockpile parameters on blending efficiency. The coneshell model is used to show that blending efficiency is highly sensitive to stacked height, with lower output variances observed for higher capacities. Output variance in both models also decreased when the stacker movement increment was decreased. For chevcon stacking, increasing stacker speed significantly increases the blending efficiencies. Increasing the length of the blending tail also reduces output variation, but this parameter would need to be weighed against the accompanying decrease in buffer capacity.IntroductionEven in the most uniform deposit of materials in nature, material properties will vary. The degree of variation can be measured, and usually resembles a normal distribution. The aim of blending and homogenization operations is to minimize the standard deviation of this normal distribution (De Wet, 1994). In general, the reduction in variation will result in a more efficient and cost-effective downstream process. Cement plants need a precise blend of raw materials to ensure desired kiln performance; boilers used in power generation are optimized for fuels of a constant specification; and even though the separation density in a coal washing plant can be adjusted, a constant product quality cannot be produced from highly variable feed (Denny and Harper, 1962). The process efficiency, product quality, and environmental compliance depend on consistency of characteristics in the material fed (Kumral, 2005) Many industries involved in"

Jan 1, 2015

By X. Xiang, W. Xia, J. Yin

"TiCl4 slurry containing valuable metals is an unavoidable by-product of the titanium ore chlorination process. The recovery of these valuable metals, which include titanium, niobium, tantalum, and aluminum, is an urgent issue to tackle in the titanium industry. The results of this investigation show that the valuable metallic elements can be recovered from the slurry by evaporation in a sealed container and leaching with dilute hydrochloric acid. After evaporation at 200°C for 60 minutes, nearly 99% of the titanium was recovered in the form of TiCl4, which was formed by the reaction of the TiO2 in the slurry with AlCl3. After evaporation, metals like niobium, aluminum, and tantalum remained in the residue. By leaching with 2.1 mol/L HCl at a L/S ratio of 6:1 mL/g at 80°C for 60 minutes, the soluble metals, such as aluminum, iron, and copper were all removed from the residue, and the niobium and tantalum were further enriched in the leach residue. A concentrate containing 53.40 wt% Nb and 5.57 wt% Ta was obtained by washing the leach residue with dilute aqueous ammonia under stirring. A potential waste water purifying agent containing 263.75 g/L AlCl3 was produced by purifying the leaching solution with Al(OH)3 and modified polyacrylamide. IntrodutionTitanium tetrachloride (TiCl4) is an important intermediate in titanium metallurgy that is widely used in the production of titania and titanium sponge (Akhtar, Xiong, and Pratsinis, 1991). In conventional titanium metallurgical processes, high-titanium materials such as synthetic rutile and high-titanium slag are reacted with chlorine to produce TiCl4 in a fluidized-bed furnace. Accompanying elements, such as Al, Nb, and Fe also react with chlorine to form chlorides, which are mixed with gaseous TiCl4 (Anderson, 1917). In the condensation process, gaseous TiCl4 is refrigerated and high-boiling-point chlorides are precipitated in the liquid TiCl4 to form a slurry containing 50~60 wt% TiCl4 (Wang, Xiang, and Wang, 2012).Various methods have been proposed to recover TiCl4 from the slurry, including microwave heating and spray drying (Wang, Xiang, and Wang, 2012, Wang et al., 2010a). To date, the only way to recover the TiCl4 is to return the slurry to the fluidized-bed furnace. However, this causes fluctuations in the temperature in the furnace, resulting in incomplete reaction between titanium-rich materials and chlorine. Therefore, the slurry is often rinsed with water and neutralized by adding lime, which caused serious environmental pollution and wastes a valuable resource (Roy, Bhatt, and Rajagopal, 2003)."

May 1, 2019

By T. Szendrei, S. Tose

The fracturing and movement of rock that occurs in the vicinity of a stemmed borehole charge in open pit mining operations are described by examining the effects of the emitted stress waves – shock and elastic – and the expansion of high-pressure detonation product gases. Three principal modes of momentum transfer to fractured rock are identified, all linked to gas expansion work. This work can be delivered radially (burden), axially (stemming), and in the collar zone (cratering). Flyrock is generated under unusual combinations of blast parameters and rock properties. Although infrequent and seldom predictable, the generation of flyrock can nonetheless be interpreted and modelled in terms of the principal mechanisms of rock projection described in this study. The physical processes underlying these principal mechanisms are identified and will permit the development of predictive models for flyrock velocities.

Dec 13, 2023