Search Documents

By L. Chanderman, C. E. Dohm

"Mineral Resource estimation (MRE) and classification are highly dependent on the confidence in the model of the orebody geometry, known as the geological model, within which the estimates are constrained. An understanding of the geology of a deposit is thus fundamental to the Mineral Resource evaluation process. The geological model is a function of the structural and depositional complexity of the geology captured by drilling information, which is limited in the early stages of a project. The information effect has a significant impact in terms of the interpretation of the geology as well as the estimation of grade continuity and the resultant risk associated with the Mineral Resource estimate and classification.Therefore, as new drilling information becomes available, it is necessary to update and refine the geological model to appropriately constrain the resource estimates. The grade information is also updated, including statistics and the spatial correlation characteristics. This refinement is based on geological interpretations derived from the drillhole information that becomes available throughout the life of the mine; orebody knowledge that comes from working experience of the deposit, as well as familiarity with the software package used for modelling, is also important.In updating, the potential to identify new resources in previously unknown areas may be realized. The opposite may also occur where previous interpretations of ore continuity are refuted. Both scenarios could result from a better understanding of the geology of the deposit and thus a more realistic MRE, which reduces geological risk. This paper describes how newly drilled advanced grade-control holes for a gold deposit in Mali were used to refine the 3D geological model for the deposit in an attempt to identify the potential for additional oxide ore using conventional geostatistical evaluation techniques."

Jan 1, 2017

By L. A. Cornish

Pt-based alloys for high-temperature applications in aggressive environments have been under development for over 10 years, and are targeted to be used as either as bulk, or as coatings. The alloys comprise Pt, Al, Cr, and Ru, and the microstructure has been improved by composition to a best possible analogue of the nickel-based superalloys, which these alloys could partially replace. This was necessary because the previous best alloy had a strengthening precipitate volume proportion of only approximately 40 vol.%, whereas the nickel-based superalloys have around 70 per cent, and a lower volume would mean that the strength would not be the best that could be obtained. The microstructures were assessed using electron microscopy, and have been related to the alloys? hardness values. The current microstructures are much more like those of NBSAs, with a high proportion of the strengthening ~Pt3Al precipitates. Since the samples have to be small (platinum is expensive), hardness has been used as an indication of strength. Nano-indentation studies showed that the hardness and Young?s modulus were higher for ~Pt3Al than the (Pt) matrix. More extensive oxidation studies have been undertaken on the previous optimum sample, and the effect of cooling rate after heat treatment has also been ascertained. In addition, the samples were studied after different heat treatment times, and cross-sections were made in order to characterize the alumina scale that formed. The oxide scales of Pt-11Al-3Cr-2Ru (at.%) up to 100 h exposure did not spall, and were at least as good as those of the ternary alloys. There was no discernable Al depletion zone in the substrate, although it could have been at a greater depth than thickness of the samples studied. Further additions to the Pt-Al-Cr-Ru alloys have been studied, to increase the melting temperature as well as to reduce the platinum content without compromising the properties. Reduced platinum content would have the benefits of reduced density and cost. The target elements include vanadium and niobium, of which vanadium is of special interest, since it is a South African product. Before these additions could be made, phase equilibria studies were undertaken so that the maximum addition could be ascertained, and also to check any possible ternary phases, which could be deleterious. Work on the Pt-Al-V system revealed a ternary phase, ~V27Pt54Al19 (at.%), which has a eutectic reaction with (Pt). The maximum V addition is likely to be around 15 at.%, otherwise ~Pt3V or the ternary phase will form, and not the required (Pt)/~Pt3Al phases.

Jan 1, 2012

By K. Wu, L. Li, D. W. Zhou, J. W. Yu

The presence of a fractured water-conducting zone (FWCZ) is of significant importance for the safety of underground mining under water bodies. When a coal mining area is covered with a thick layer of alluvial soil, the height, width, and distribution pattern of the FWCZ in the area shows unique features. The internal mechanism by which thick alluvial soil affects the FWCZ is still unknown. Using the Huainan coal mining area (HCMA) in China as a case study, we investigated the impact of thick alluvial soil on the height, width, and distribution pattern of the FWCZ through numerical simulation using the distinct element method, theoretical derivation, and data validation. The results indicate that a thick layer of alluvial soil inhibits the FWCZ height and increases the FWCZ lateral width. When the soil-to-rock ratio is greater than a certain value (the numerical result in this study is 15:18), the FWCZ height and width are affected by the thick alluvium significantly, and the thick alluvial soil alters the shape of the FWCZ from tall and thin to short and wide. The load exerted by the alluvial soil transfers downward to influence the FWCZ; however, this process is obstructed by the hard strata in the bedrock. Therefore, the vertical and lateral change trends show a similar step pattern. Our results can provide a basis for accurate calculation of the FWCZ height in mining areas with thick alluvial soil, to mitigate mine water hazards and increase the safety of underground mining in coal mines covered with a thick alluvium layer. Moreover, reducing the FWCZ height can help extend the upper extraction limit in coal mines covered with a thick alluvium layer, which reduces the thickness of the impermeable coal pillar and increases coal production.

Jan 1, 2016

By E. M. Sacris

The semi-autogenous grinding mill is the bottleneck whenever treating hard and finely fragmented ore at Benguet Corporation's Kaline Concentrator. Low milling rates result from very high and fluctuating mill power draw. Attempts to use a mill horsepower control loop to regulate feed rate were unsuccessful because of operational upsets caused by fluctuations in feed rate on downstream operations. The objective of the computer control was to maximize tonnage throughput by stabilizing the power draw at a high but safe level without upsetting subsequent operations. The semi-autogenous mill is operated in closed circuit with a stationary screen. Instrumentation consists of a feed weightometer, a power transmitter to measure mill load, a headwater flowmeter and an ultrasonic level sensor to measure the mill discharge sump level. A 64 k-byte FOX-3 Foxboro computer processes field data from various sensors and manipulates the input control variables. These variables are the fresh feed rate and the headwater flowrate. Feed rate is controlled through a supervisor-type computer program aimed at maximizing and stabilizing power draw. The control scheme was according to how the operators responded during an operator-directed automatic control mode. Mill dilution is similarly controlled. Results achieved reflect a 3% increase in tonnage milled because of the reduction in control variability that ensued.

Jan 1, 1987

The AMIRA Code of Practice and Guidelines for Metal Accounting was developed in response to demand from a number of sponsor companies, including one major platinum producer. Since its publication in 2007, the Code has become widely accepted in the mining industry world-wide as a guide for best practice in metal accounting. With the changes in the structure of the platinum mining industry in South Africa over the last 10 ? 15 years, in particular, the starting up of a number of small platinum producers who must have their concentrate smelted and the contained valuable metals refined by third parties, the need for metal accounting systems that are accurate and have an acceptable level of precision has become even more critical to the success of a platinum-producing operation. The current state of metal accounting in the industry is discussed and possible areas for improved accounting and associated metallurgical efficiencies are identified.

Jan 1, 2012

By D. Botha, J. F. Cronjé

"SynopsisAlthough women all over the world have been involved in mining activities for centuries, mining has always been considered a very masculine industry due to its heavily male-dominated workforce as well as the physicality of mining work. The mining industry has not been an obvious career choice and preferred place of employment for women; women were mainly employed in administrative and advisory positions. Until 1994, women were legislatively prohibited from being employed in underground operations in South Africa, but the Mines Health and Safety Act, No. 29 of 1996, removed these restrictions. In addition, new mining legislation (the Mineral and Petroleum Resources Development Act, No. 28 of 2002) and the accompanying Mining Charter make specific provisions for the inclusion of women in core mining activities and require 10% of core positions to be filled by women.This article voices perceptions of the physical ability of women employed in core mining positions. Findings are drawn from empirical work undertaken at platinum, phosphate, and copper mines. Quantitative and qualitative research paradigms are used. It is evident that women find it extremely difficult to perform mine work that requires physical strength and stamina. Practical recommendations, informed by the literature review and empirical findings, are made with the objective of contributing to the sustainable deployment of women in the mining industry.IntroductionFor many years, mining has been considered the foundation of the South African economy. Although the mining industry in South Africa is currently under considerable pressure and experiences various challenges, including escalating operational costs, electricity tariff increases, safety-related issues and associated production stoppages, poor productivity, labour unrest, and reduced demand both globally and domestically, it remains a key contributor to the national economy and development of the country (IDC, 2013, p. 9).Until 1994, women were legislatively prohibited from meaningful participation in the mining industry and were denied access to skills and jobs, self-employment, and entrepreneurship. The newly elected democratic government in 1994 initiated substantial socio-political and economic transformation in South Africa. Nearly every sector in the country was transformed and re-shaped, primarily through sector-specific legislation, but also through negotiations between government, industry, and labour unions to create and refine the so-called sector charters, which included the Mining Charter. The vision of the new regime, the African National Congress (ANC), was to ‘transfer power to the people and transform society into a non-racial, non-sexist, united, democratic one, and change the manner in which wealth is shared, in order to benefit all the people’ (ANC, 2007)."

Jan 1, 2015

By M. Z. Emad, Y. Majeed, G. Rehman

Massive deposits of rock salt are mined in the Salt Range area of Pakistan. The main export products of rock salt include salt lamps, blocks, and tiles, while local consumption includes the chemical industry and domestic use. The profitable production of salt for value addition depends on the quality, size, and shape of the block. Salt processing for value addition is easier when very few cracks are present in the blocks. The current salt mining practice involves drilling and blasting, which introduces undesired fractures in the material. This paper focuses on the extraction of rock salt blocks by applying conventional cuboidshaped block mining methods used in quarries. The techniques include wedges and feathers, expansion chemicals, and blasting with low-yield explosives. Experimental work involved both laboratory-scale and in-situ field testing. Laboratory experiments assisted with the determination of splitting force, loaddeformation curves, and other rock mechanics parameters. Regression analysis proposes a relationship for the estimation of radial strain from the load in the case of the wedges and feathers method. The splitting force obtained from the laboratory tests was used to confirm the accuracy of the already published empirical relationship. The results of the laboratory as well as in-situ tests showed that the wedges and feathers technique is the most suitable method for mining rock salt blocks of the desired size, shape, while minimizing cracking.

Mar 2, 2022

By Z. Gxowa, L. H. Chown, U. Curle, G. Govender

This work evaluates the deformation behaviour, at warm working temperatures, of green particle-reinforced aluminium composites produced by powder blending in a high-energy ball mill. The work focuses on metal matrix composites (MMCs) based on the 2124-Al alloy, reinforced with 10 or 15 vol.% SiC and metal matrix nanocomposites (MMNCs) based on the 2124-Al alloy, reinforced with 5 or 10 vol.% Al2O3. Three batches for each powder were blended and powder properties such as particle size distribution (PSD) and shape were consistent after blending. It was observed that a more uniform distribution of the reinforcement phase in the aluminium alloy matrix was achieved in 2124-Al/Al2O3 than in 2124- Al/SiC composites. The powders (unreinforced 2124-Al and blended) were initially over-aged at 350°C for 2 hours to reverse any natural ageing that may have occurred prior to use. The over-ageing was incorporated to improve compressibility of the powders with the aim of achieving green compacts with higher integrity. Uniaxial compression tests performed at ambient temperature on a Gleeble® 3500 thermomechanical simulator were unsuccessful as the green compacts fragmented. Engineering stress-strain curves showed that green compacts of unreinforced 2124-Al, 10%SiC MMC and 5%Al2O3 MMNC deformed in a similar manner at ambient temperature and had the same compressive fracture stress of approximately 170 MPa. When the deformation temperature was increased from ambient to warm working temperatures (170–280°C) it was observed that electrical resistance heating (the heating mode of the Gleeble®) of unreinforced Al alloy, MMC and MMNC green compacts did not occur. This was attributed to the high electrical conductivity of aluminium, which resulted in poor heat generation due to the low electrical resistance in the samples. It was presumed that the small sample size (d=8 mm, h=12 mm) also caused rapid heat loss. After further experimentation, the green compacts were heated successfully by insulating the samples to retain heat. It was found that at 280°C, increasing the soaking time from 6 to 20 minutes decreased flow stress and improved plastic flow in the 2124-Al/10%SiC green compact.

Jan 1, 2016

By M. P. Brandt, T. P. Knoetze, I. I. M. Kessler

It has generally been accepted that the volatile mater in a coal is the factor that determines whether or not a specific coal dust is an explosion risk. This paper presents the results of an attempt to relate the explosibility index (Kex) of South African coals, as determined in a AD-litre explosion vessel, to the volatile mater content of the coal and the calorific value of the volatiles. A good relationship between the calorific value of the volatiles and the explosibility index was established, which makes it possible to calculate the violence of an explosion, as expressed by Kex, for South African coals. The Kex value is but one of a number of parameters that influence the explosion hazard in a specific colliery and cannot be used as the sole predictor of the propagation of an explosion underground. Other parameters include the ignitability of the coal, temperature, humidity, dispersibility of the dust, methane concentration, amount of incombustibles present, and ventilation.

Jan 1, 1993

By R. B. Ngenda

The ?Kolwezi Zinc Plant?, in French ?Usines à Zinc de Kolwezi? (UZK), has produced about 910 000 dry metric tons of residues during the hydrometallurgical treatment of calcines from sulphide zinc concentrates. The zinc hydro plant residues contain on average 19.47% Zn, 2.7% Cu, 2.1% Pb, 26.6% Fe, 0.12% Cd, 0.39% As, 157ppm Ag, 447.8 ppm Ga, 475.4 ppm Ge, etc. This material was dumped in five ponds in the vicinity of the plant. The high Fe content in the ore concentrates induced important conversion of some of zinc and copper into ferrites during the roasting process. Those ferrites are very stable compounds, which are difficult to leach with dilute sulphuric acid solution. Therefore, they mainly report to the leaching residues. Hot leaching has been successfully applied to the treatment of zinc hydro plant residues. The method, however, presents the disadvantage of simultaneously dissolving iron(Fe). It is then necessary to remove an important iron quantity from solution prior to zinc and other metals recovery.

Jan 1, 2009

By R. J. Durrheim, Y. Yabe, M. S. D. Manzi, DSeis team, N. Z. Nkosi, S. B. Mngadi, Jr. H. Ogasawara

On 5 August 2014, the Orkney M5.5 earthquake, the largest in South African gold mining districts, occurred with an unusual strike-slip mechanism at great depth of 4.78 km below the surface. In a rare case, the ML 5.5 earthquake occurred within the area covered by the legacy 2D and 3D reflection seismic data acquired in the 1990s and 2000s for gold exploration and mine development. In addition, the earthquake ML 5.5 rupture plane was recorded and accurately delineated by the underground in-mine seismic network near the source region. The integration of the legacy 2D reflection seismic data and mine seismicity data allowed us to identify a near-vertical structure, striking northnorthwest-south southeast (NNW-SSE). The ICDP-DSeis team drilled three holes (Hole A, Hole B, and Hole C), and two holes (Hole B and Hole C), intersected the upper edges of the ML 5.5 rupture. These holes recovered metasediments, metabasalts, intrusive rocks including dolerite sills and lamprophyre dykes adjacent to the fault zone, and the fault gouge. Late Prof. Tullis Onstott and geomicrobiologists installed a packer in Hole A and successfully recovered saline water and detected gas (~10 MPa). Slip weakening and rupture propagation are significantly influenced by the existence of fault gouges and the production of wear material between two sliding rock surfaces. Using the fault gouge material recovered from Hole C, we conducted friction experiments under dry and room temperature conditions at high slip velocity of ~100 mm/s and normal stress of 2 MPa. The resulting steady-state frictional strength was ~0.66 over a slip weakening distance of ~9.1 m. The steady-state frictional strength was high, which may be caused by large gouge thickness, and the rate of wear generation. As a result, it is proposed that the Moab Khotsong ML 5.5 seismogenic zone is complex and could be controlled by three main processes: a) the complex structural architecture of the seismogenic zone (e.g., intersection of fault, lamprophyre dykes, and dolerite sills); b) the mechanical process induced by tectonic and/or mining related stresses; and c) the mechanical and chemical processes caused by the water and rock interaction.

Jan 12, 2025

By A. E. Lewis, J. Du Plessis, J. Chivavava

Current metallurgical processes lack selective and efficient REE recovery from aqueous leach liquors. Antisolvent crystallisation is used to selectively recover pure inorganic salts from aqueous solutions without excessive chemical use in ambient conditions. Yttrium sulfate octahydrate (Y2(SO4)3.8H2O) was used as a representative rare earth salt to investigate the effect of antisolvent selection on the crystal morphology and size distribution of the final crystalline product produced through antisolvent crystallisation. The antisolvents of choice were short length alcohols that are water miscible i.e. methanol, ethanol, 2-propanol and t-butanol. All experimental parameters except the type of antisolvent were kept constant under isothermal conditions. The large reduction in solubility of the salt by the antisolvent creates high supersaturations. This leads to high product yields as observed in this study at > 91%. In general, a variety of morphologies were successfully formed in each individual alcohol including; rods, plates, prismatic cubes and starburst clusters. The powder X-ray diffraction (XRD) analysis indicated that Y2(SO4)3.8H2O was the only species present for all final products. There was a change observed from the starburst and rod structures for the shorter alcohols towards prismatic cubes for the longer alcohols due to different strengths in the solute-antisolvent interaction at the crystal growth faces. The crystal sizes increased with an increase in the alcohol chain length because of the lower supersaturation conditions due to a limit in the mass transfer induced by the bulkier alcohol structure. In conclusion, it has been shown that the particle morphology and size can be greatly affected by the selection of antisolvent even under high supersaturation conditions, contributing to understanding the effect of different antisolvents on the final particle characteristics. The engineering of favoured product characteristics can therefore be achieved by antisolvent crystallisation, presenting a viable alternative process for the recovery of REE. Keywords: Antisolvent crystallisation, rare earth elements, morphology, particle size

Jan 1, 2020

By J. Fu

"Since it was first identified in 1817, selenium has received considerable interest. Native selenium and a few selenium minerals were discovered several decades later. With the increasing number of selenium minerals, the occurrence of selenium minerals became the focus of much research. A great number of selenium deposits were reported all over the world, although few independent selenium deposits were discovered. Selenium is obtained mainly as a byproduct of other metals, and is produced primarily from the anode mud of copper refineries. This paper presents a comprehensive review of selenium minerals, as well as the treatment of copper refinery anode slimes for the recovery of selenium. Our focus is on the selenium minerals, including their discovery and occurrence, and the distribution of selenium resources. In addition, the main methods of recovering selenium from copper anode slimes are summarized. IntroductionSelenium (Se) was first observed in 1817 in a laboratory (Greenwood et al., 1984). The discovery of selenium was made by the Swedish chemist J.J. Berzelius and J.G. Gahn, who isolated selenium from a red residue in sulphuric acid from pyrite mined at Fahlun, Sweden. Selenium was named from the Greek word selene (moon), since it resembled tellurium, which had been discovered a few years earlier and named from the Latin word tellus (Earth).After the first observation of selenium in the laboratory, selenium received considerable interest. In 1954, E.P. Kaiser pointed out that Se is enriched in sulphide ores and often associated with Bi, Co, Sn etc. (Kaiser 1954). In 1959, Hawley and Nichol investigated selenium in Canadian sulphide minerals, and presented the content of selenium in sulphide from several deposits of different types. They also proposed that Se is enriched in lowtemperature hydrothermal pyrite (Hawley and Nichol, 1959). The thermodynamic conditions for forming native selenium and selenium minerals in sedimentary rocks were discussed, as well as geochemical behaviour of selenium near the oxidation zones of sulphides in the 1970s (Howard III, 1977; Zhu et al., 2003). Zhu et al. examined the morphology, features, and genesis of native selenium from Yutangba, Enshi City, Hubei Province, China in 2004, and pointed out, from the different forms of native Se, that selenium can be activated,transformed, remobilized, and enriched at sites such as in the unsaturated subsurface zone or in the saturated zone (Zhu et al., 2005). The transport and deposition of selenium in felsic volcanic-hosted massive sulphide deposits of the Yukon Territory, Canada was studied and reported by Layton- Matthews et al. (2005)."

Jan 1, 2016

By D. Kumar, B. Rai, S. G. Srinivasan, V. Jain

Chalcopyrite and pyrite are among the major gold bearing minerals in the world. The gold content in chalcopyrite and pyrite varies from 0.02 to 200 ppm and 0.01 to 20 ppm, respectively. Apart from gold, chalcopyrite is also the primary source of copper. Thus, the recovery of gold and copper are often associated with the recovery of chalcopyrite and pyrite. Flotation is one of the most successful methods applied to beneficiate chalcopyrite and pyrite. The success of a flotation process depends on an appropriate choice of the flotation collector used to achieve the desired selectivity. A thorough understanding of the atomic structure of the predominantly exposed mineral surfaces can immensely aid in developing highly selective collectors that can exploit both the physical and chemical characteristics of these surfaces. In the present study, density functional theory calculations within the plane wave framework are used to understand the surface structure and reconstruction of the most stable chalcopyrite (001), (100), (110) and (112) and most stable pyrite (100) surfaces. The chalcopyrite (001) and (100) metal-terminated surfaces undergo significant reconstruction and result in metal-metal bond formation in the sub-surface layer while the surface layer is replaced by S-atoms. On the other hand, the (001) and (100) S-terminated surfaces show S—S disulfide bond formation upon relaxation, which are consistent with literature reports. The chalcopyrite (110), (112) surfaces and pyrite (100) surface undergo rearrangement, but no reconstructions in terms of metal-metal or disulfide bond formation are observed on these surfaces. Keywords: DFT, surface reconstruction, pyrite, chalcopyrite, adsorption

Jan 1, 2020

By P. Lenegan, R. Masethe, R. I. L. Ferreira

Underground mining in high rock-stress environments can induce unanticipated dynamic rockmass deformation, posing a serious risk to the workforce. Data collected by seismic networks are imperative for the design-as-you-mine process. Often an inappropriate assessment of the seismic hazard is done when unnecessary data are included in analytical techniques, particularly short-term time frames. Depending on the methodology or application of data analysis and interpretation, some of the information may not be relevant and even detract from the objective. By using the spatial event clusters associated with active workplaces to define the shape and size of the polygons for data selection for subsequent analysis, a problematic subjective component can be eliminated. The mining of tabular reefs in South Africa, be they gold- or platinum group metals, is very extensive, and underground workplaces are often widespread. Production stoppages are very costly, especially for marginal mines, so there is just cause not to evacuate an entire operation’s workforce following the occurrence of a large mining-induced seismic event. A rationale based on the damaging peak particle velocities (PPV) of the past seismicity can exclude the unaffected underground personnel and allow a quick orderly withdrawal where required. Micro-deformation may precede rockbursting, which can occur on-shift close to the workface. A mine-wide array of geophones suitable for the accurate location and analysis of seismicity may not be able to detect these higher-frequency emissions. Inexpensive but fit-for-purpose accelerometers, providing real-time, continuous measurement of acoustic rockmass deformation near the workplace, integrated through underground and surface communications networks, are shown to record ‘rock-talk’, clearly distinguishable from the instrument background noise, which can be in the order of hours leading up to an imminent damaging seismic event.

Jan 12, 2025

By T. Feroze, B. Genc

"The effect of some of the system variables in forcing and exhausting ducted fan systems on ventilation in an empty heading was investigated using computational fluid dynamics(CFD) and comparative analyses. The diameter of the duct, duct mouth to face distance, and the power of the fan (quantity delivered by the fan) were varied and their effect on ventilation determined through a comparative analysis of the flow rates calculated close to the face of the heading. Estimation models were developed, which can be used to calculate the flow rate close to the face of the empty heading for different settings of the system variables studied.The study showed that recirculation for a forcing ducted fan system can be reduced by increasing the duct diameter or increasing the duct mouth to face distance. For the exhausting ducted fan system, higher flow rates were achieved by reducing the duct mouth to face distance, andincreasing the fan design flow rate and duct diameter.The outcomes of this investigation will help ventilation engineers in deciding the optimum duct fan system required for sufficient ventilation.IntroductionThe ventilation of underground mines, irrespective of the type of mine and mining method, is divided into two broad branches, the primary ventilation and secondary or auxiliary ventilation. The primary ventilation is responsible for the total volumetric flow through the mine and the auxiliary ventilation is responsible for the ventilation of the development ends, production areas, and facilities disconnected from the main circuit with no through-ventilation connections. Auxiliary ventilation is the more difficult to achieve (Bise, 1996), and the disruption of this ventilation system is considered to be one of the primary factors contributing to methane and coal dust explosions (Creedy, 1996). A number of causalities have been recorded by many authors due to these explosions (Phillips and Brandt, 1995; Dubinski et al., 2011; Phillips, 2015). The ventilation of short headings, less than 10 m in depth, can be carried out without the use of any auxiliary equipment (Feroze and Phillips, 2015). However, for headings deeper than 10 m, auxiliary ventilation systems are required. These are generally classified into the three basic types, namely line brattice (LB) ventilation systems, ducted fan systems, and jet fans (Figures 1 through Figure 3 respectively)."

Jan 1, 2017

By M. Hao, S. Hu, X. Lyu, M. Lian, C. Anning, G. Yao, Z. Wang

The results revealed that the pozzolanic activity of the gold mine tailings and their main mineral phases improved by mechanical activation. Under the same activation conditions, the activated mica powders possessed the highest pozzolanic activity index, followed by the activated feldspar, and the activated quartz exhibited the lowest pozzolanic activity index. The addition of calcium oxide promoted the formation of amorphous C–(A)–S–H gel for all paste samples, and stratlingite and hydrotalcite were observed in calcium oxide activated mica paste. The addition of natural anhydrite promoted the formation of ettringite for the pastes of calcium oxide activated aluminosilicates materials (gold mine tailings, mica, and feldspar). Furthermore, the pozzolanic activity indexes of the mechanically activated gold mine tailings and their main mineral phases were tested to be qualified for use as supplementary cementitious material in cement. This paper provided an innovative approach for recycling gold mine tailings as supplementary cementitious materials in cement, which would be environmentally friendly and cost-effective. Keywords: Mechanical activation, gold mine tailings, supplementary cementitious material, hydration properties, pozzolanic activity

Jan 1, 2020

By C. M. Rule, A. K. Anyimadu, L. Knopjes

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Key Words: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, Platinum, Palladium, PGMs, tailings.

Jan 1, 2006

Book review Proceedings of the Symposium on Mining Methods. London, Institution of Mining and Metallurgy, 1974. 160 pp. The Symposium was held from 30th October to 1st November, 1974, and the papers include an interesting range of subjects in coal-mining operations, covering the improvements achieved to date, current practice, and required development for the future. Salamon, M.D.G., and Oravecz, K. 1. Rock Mechanics in Coal Mining. 119 pp. NIM reports Report no. 1822 Stability constants and linear free-energy relations for the platimtm-group metals. (22nd Oct., 1976). Report no. 1852 A revised method for the dissolution of platiniferous materials by the sealed-tube technique. (18th Oct., 1976). Report no. 1828 y-picoline adducts of the nickel, copper, and zinc chelates of 2-thenoyltrifluoroacetone. (26th Nov., 1976) Report no. 1847 A pilot-plant investigation of a kinetic model for flotation.(19th Nov., 1976)

Jan 2, 1977

By D. He, A. Yaacoubi, A. Baçaoui, K. Boujounoui, A. Abidi, K. El Amari

The effects of utilizing recycled tailings pond water from the flotation plant at the Mining Company of Guemassa (MCG) on galena recovery and selectivity towards chalcopyrite (RPb-Cu) , sphalerite (RPb- Zn), and pyrrhotite (RPb-Fe) were studied at bench scale. The results showed that recycling the tailings pond water in the lead circuit without addition of fresh water gave a good flotation performance in terms of lead recovery (Rpb) (75%) and selectivity towards the other metals: RPb-Cu (54%), RPb-Zn (60%) and RPb-Fe(65%). This allows the water to be recycled at least four times. However, increasing the d80 from 100 μm to 160 μm currently used at the MCG plant had a negative effect on the lead flotation performance.

Nov 30, 2022