Search Documents

By C. M. Flynn

The Bureau of Mines prepared and investigated xanthated sawdust adsorbents to determine their effectiveness in removing heavy metal ions from dilute aqueous solutions, mine-drainage waters, and brines. Stripping of the metal values from the metal-laden adsorbent was also investigated. The treated sawdusts had an adsorption capacity of 0.3 to 0.4 meg/g dry adsorbent for Mn, Co, Ni, Cu, Ag, Zn, Cd, Hg, or Pb from feed solutions with pH 5 to 6. The feed solutions tested included mine-drainage waters and geothermal brine. Effluent metal concentrations as low as 0.05 to 0.1 mg/l were obtained at effluent pH values of 6 to 9. The order of affinity of metals for the sawdust adsorbent is Na«Ca~Mg~Mn<Zn<Ni<Cd<Pb~Cu. The presence of Ca, Mg, or Na in concentrations as high as 2 g/l does not seriously impair the heavy-metal adsorption. Metals were desorbed from the metal-laden adsorbent by elution with dilute mineral acids, sodium cyanide, or salts of ethylenediaminetetra-acetic acid.

Jan 1, 1979

By Richard Mainiero, James H. Rowland

For many years there have been small scale tests available for evaluating the toxic fumes production by cap-sensitive explosives (DOT Class 1.1), but these could not be used with blasting agents due to the large charge sizes and heavy confinement required for proper detonation. Considering the extensive use of blasting agent in construction and mining, there is a need to determine the quantities of toxic fumes generated by blasting agents. At the International Society of Explosive Engineers Twenty Third Annual Conference on Explosives and Blasting Technique in 1997, the authors reported on a facility for detonating large (4.54 kg), confined blasting agent charges in a controlled volume that had been constructed at the National Institute for Occupational Safety and Health’s Pittsburgh Research Lab’s Experimental Mine. Since 1997, this facility has been used to collect data on toxic fumes produced by the detonation of various ammonium nitrate/fuel oil (ANFO) mixtures and several cap-sensitive explosives. ANFO composition ranging from 1 to 10 percent (pct) fuel oil have been studied. As expected from previous studies, with an increase in fuel oil content the carbon monoxide production increases, while nitric oxide and nitrogen dioxide production decrease. The detonation velocity varies from 3,000 to 4,000 m/sec for the 1to 10 pct range of fuel oil content, suggesting that ANFO mixes with improper fuel oil content may appear to detonate properly, while their fume production differs significantly from optimum. The study also considers such factors as degree of confinement, water contamination, and aluminum content on blasting agent fume production. Results indicate that water contamination of the ANFO has little effect on carbon monoxide production, but causes significant increase in nitric oxide and nitrogen dioxide production. Decreasing confinement from Schedule 80 steel pipe to 0.4-mm thick sheet metal also has little effect on carbon monoxide production, but significantly increases nitric oxide and nitrogen dioxide production. Adding5 and 10 pct aluminum to the ANFO had no clear effect on carbon monoxide, nitric oxide, or nitrogen dioxide production.

Develop quieted, hand-held pneumatic percussion drills that can replace standard hand-held drills in many underground mining applications. The Problem Percussion drills are the noisiest machines used in underground mines; noise levels of 115 to 120 dBA are common, requiring the use of hearing protectors and limiting the time a miner is permit-ted to operate the drill during an 8-hour shift. Hand-held pneumatic percussion drills pose a particularly difficult problem because the operator cannot be isolated from the noise source (e.g., an acoustical cab), and alternative technologies for drilling roof bolt holes and blastholes in tight quarters are not readily available.

Jan 1, 1984

This chapter presents data on occupational exposures from several sources. Data from compliance samples obtained by MSHA inspectors are presented in table 6-1 for coal mine dust and silica dust, and in tables 6-2 through 6-6 for metal fumes. Since these samples were taken for compliance monitoring rather than as part of a survey of the industry, it is difficult to predict how well they indicate actual exposures for all mining operations. In the coal industry, 7.8% of all respirable dust samples during 1986-1995 were above the permissible exposure limit (PEL). Of silica dust samples obtained during the 10-year period, 23.7% were above the PEL in coal, 16% in metal, 10.8% in nonmetal, 9.1% in stone, and 7.6% in sand and gravel. Of metal fume samples, silver samples showed the largest percentage above the PEL-approximately 48% of samples in both metal and nonmetal. Tables 6-7 and 6-8 present data on noise exposures from the MSHA "dual threshold" survey, which was published in the Federal Register [61 Fed. Reg. 66347 (1996)] as part of a proposed rule change for occupational noise exposure in mining. This study examined a group of samples obtained during 1991-1995 and compared the percent of samples that were above two separate specified limits. The first limit was the current noise standard, a time-weighted average of 90 dBA, calculated to include only exposures at 90 dBA and above. The second limit was a time-weighted average of 85 dBA, calculated to include exposures at 80 dBA and above. Tables 6-8 and 6-9 refer to musculoskeletal overload conditions examined in the National Occupational Health Survey of Mining (NOHSM) [NIOSH 1996]. Table 6-8 shows the operational definitions for each condition; table 6-9 shows the percentage of the workforce potentially exposed, by commodity. Across all commodities, a large proportion of workers were exposed to musculoskeletal overloads due to positioning of the neck and back; positioning and motion of the forearms, arms, and shoulders; heavy lifting; and positioning and movement of the lower limbs. The recorded overloads were defined in the survey and did not exceed any NIOSH, MSHA, or OSHA guidelines for musculoskeletal overloads. Further information on this survey appears in appendix A.

Jan 5, 2000

By Thomas V. Falkie, R. Venkataramani

Underground coal winning operations can broadly be classified as conventional, continuous, and longwall mining. In conventional mining, the operations of cutting, drilling, blasting, loading and hauling, and roof support are performed in that sequence in each working face in a work area. The major difference between continuous and conventional mining is that the coal is cut and loaded by a continuous miner in the former, thereby combining the unit operations of cutting, drilling, shooting, and loading into one. Longwall applications have been viewed with great interest in recent years, and although at the end of 1970 there were only 37 longwall installations in the U. S. with combined production of less than 4 percent of underground total, there is no question about the growth potential of longwall in the United States. Increased capacity, versatility, and power characterize continuous miners today. Although continuous miners have outsold conventional gathering-arm type loading machines for some years, the latter, in the new extra-high capacity types, are continuing to find wide use. Whether the mining system is continuous or conventional, the haulage units may include six-wheel articulated shuttle cars, tractor-trailer units, or extensible belt and bridge-conveyor systems, all tending to increase the productivity of the face units. The decision as to which to choose - continuous or conventional mining - is complicated, and both systems are capable of high production rates. Most continuous miners in use today have a revolving pick-mounted drum to cut the coal and a gathering arm loading unit. Functionally, there is little difference between the loading unit in a

Sep 1, 1972

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) IS linked to cumulative back, neck, and abdominal disorders. In low-coal mines, space restrictions make seat suspensions difficult to use in isolating operators from shock and WBV. Researchers at NIOSH, Pittsburgh Research Laboratory, are responding to these issues by investigating viscoelastic foams. For the full-load case. an ergonomic seat with viscoelastic foams isolated the shuttle car operator from shock at 15 Hz. Researchers used results from additional foam testing with an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

By Jr. Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

The Bureau of Mines Minerals Information organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7. 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Minerals Information activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1985

By Edward Thimons, William A. Hertbrink

The effect of wind speed upon aerosol penetration into an idealized enclosure was studied The idealized enclosure was a painted plywood box that was 1 2X1 2 XI meters in volume Two fans supplied 1 7 m3 /min of filtered air to this enclosure at a static pressure of 2 8 mm of water The enclosure had a 7 5 cm diameter vent port which was isolated from the air flow around the enclosure To simulate holes in real enclosures, three 16-cm diameter holes were drilled on the front and back sides of the enclosure This simulated enclosure was placed in a tunnel-like structure The air flow from an ultra-light air craft was directed at the front of the enclosure The air speeds were varied between 14 and 36 km/hr as measured by rotating vane anemometer Static pressure in the enclosure was measured with an electronic manometer Two optical particle counters measured the particle number concentration of particles between the 0 35 to 0 5 µm inside and outside of the enclosure Aerosol penetration into the enclosure was computed as the ratio of the aerosol concentration inside the enclosure to the concentration outside of the enclosure The enclosure static pressures measured increase from 2 8 to 3 4 mm of water (P=00001) Aerosol penetration into the enclosure increased linearly with air velocity above 20 km/hr Theoretically estimated penetrations were correlated with observed penetration into the simulated enclosure When simple linear regression was used to model the observed penetration as a function of the estimated penetration, the value of the slope was 0 69±0 12 and the P value for the regression model was less than 0 0001 These results indicate that enclosure static pressure needs to be higher than the wind&apos;s velocity pressure in order to minimize aerosol penetration into these enclosures

Jan 1, 1999

By Thomas M. Barczak

The success of longwall mining can largely be traced to the development of powered roof support systems. The most significant improvement in powered support design has been the shield support, which improved kinematic stability and promoted the application of longwall mining in difficult-to- control caving conditions where chock and frame supports were inadequate. The most obvious trend in shield design has been an increase in shield size and capacity. This U.S. Bureau of Mines report examines shield design and operation practices and their consequences for the utilization of high-capacity shield support systems. An optimization goal is to minimize support loading by selecting an active shield setting force that is compatible with strata behavior and shield loading characteristics. Shield stiffness is an important design parameter that is often overlooked. A consequence of increasing shield capacity by incorporating larger diameter leg cylinders is a proportional increase in shield stiffness. Setting forces have also increased in direct proportion to the increase in shield capacity. The increased stiffness and higher setting force cause the available capacity to be consumed more quickly, severely limiting the ability of high-capacity supports to last longer and provide reserve capacity for difficult mining conditions.

Jan 1, 1992

By D. B. Taliaferro, David M. Logan

which an operator may obtain detailed information regarding all projects in the State. It is the purpose of this report to present data such as volume of oil produced monthly, volume of water injected monthly, spacing of wells, number of injection wells and oil wells, and other such pertinent information regarding every project in the State whether active or abandoned and whether a success or a failure. It is believed that with these data it is possible to analyze water-flooding operations in this area more completely than has been possible in the past. As the title indicates, the report is essentially a history, and ordinarily no opinion is given as to the cause for the success or failure of individual projects. Increasing the production of oil is exceedingly important at this time, and one method by which it may be done most readily is by providing additional energy for the movement of oil in many of the older fields. In many oil fields the predominant force that drives oil through the porus reservoir rocks to wells is the gas dissolved in or otherwise associated with the oil under pressure. As the pressure in the reservoir declines in consequence of the removal of fluid, gas comes out of solution in the form of minute bubbles; as the pressure is reduced further, the expansion of these bubbles forces part of the oil toward the areas of lowest pressure and into the producing wells. The physical properties of the oil and the gas governing their flow through reservoir rocks to wells differ, and much of the gas slips past the oil leaving large quantities of oil in the reservoir when the pressure has been exhausted. Often the natural productive life of fields is prolonged by reducing the pressure in oil wells below atmospheric with vacuum pumps; but the ad- ditional energy made available in this manner is limited to less than 1 atmos- phere of pressure, and even after the extended application of "vacuum" to a petroleum reservoir large quantities of oil are left unrecovered in the porous rocks and sands.

Nov 1, 1943

By E. P. Youngman

Ethiopia is generally conceded to be rich in minerals. The lack of mineral development in that country is attributable not so much to the in- accessibility of the deposits as to political conditions. Ethiopia is the only country in the Continent of Africa that has maintained its political independence; and now that it has a progressive and enlightened ruler, Ras Taffari, hope is entertained in many quarters that through foreign partici- pation the Ethiopian mining industry will develop rapidly.

Nov 1, 1931

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 B. t. u. compared with 597,000 B. t. u. in 1936. These amounts represent roughly the heat obtainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at refineries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels were 11 percent higher than in 1930; the average operating ratio was 83 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 638,149 billion B. t. u. in 1936 to 663,966 billion B. t. u. in 1937.

Jan 1, 1938

Provide longwall operators with practical information and guidelines concerning mine design to reduce problems associated with the interaction of adjacent workings in multiple-scam longwall mines. Background The high productivity achieved by longwall mining demonstrates its potential to provide a substantial segment of underground coal production. Longwall mines produce more than 30 pct of underground coal, up from pct just 15 years ago. However, the continued growth of this mining method without appropriate multiple-seam planning may increase the cost and risk of mining. Research by the U.S. Bureau of Mines (USBM) indicates that 25 longwall mines (32 pct of the total number in the United States) have mining in adjacent coalbeds either above or below. About half of these longwall mines report some type of interaction problem with the adjacent workings, such as caving due to subsidence. Optimization of mine design factors is the best means for controlling interactions between operations in adjacent scams. To avoid higher mining costs, operators should focus on adopting practices and procedures that prevent and control interactions in multiple scams. The USBM, in an effort to improve longwall mine planning, has been investigating multiple-seam longwall design and development.

Jan 1, 1994

By R. R. Sayers

Carbon monoxide poisoning is one of the most widely distributed and most frequent causes of industrial accidents . Carbon monoxide gas is a product of incomplete combustion , and since it is without color , odor , or taste , its presence is frequently unsuspected in many places where it exists . It is an ever present danger about blast and coke furnaces , smelters , and foundries . It may be found in buildings having a leaky furnace or chimney , and in buildings where a gas stove is used without a proper flue connection , such as is often found in tenements , tailor shops , and boarding houses . Hospitals receive annually a great number of victims of poisoning , either by accident or in an attempt at suicide , from artificial illuminating gas . People may be affected by leaks wherever water gas is formed or used . The exhaust gases from gasoline motors under average running conditions usually contain 5 to 7 per cent carbon monoxide , and sometimes as much as 13 per cent ; deaths from running an automobile engine in a closed garage are not infrequent . A similar danger may arise in operating gasoline engines in launches without sufficient ventilation . The gas is formed also in stoker rooms , in gun turrets on battleships , in petroleum refineries , and by the Lablanc soda process in cement and brick plants . In underground mines carbon monoxide may appear as the result of shot firing , mine explosions , or mine fires , and in tunnels where automobiles , coal or oil - burning locomotives are operated . In spite of the common occurrence of carbon monoxide poisoning there appears to be no uniformly recognized treatment for a person overcome by carbon monoxide . In the rescue work of the United States Bureau of Mines , however , a method has been developed which has been supported by laboratory investigation , and has proved successful in practical experience , over a period of years . As outlined in this article , the method is useful in the hands of first -aid men as well as physicians .

Dec 1, 1921

By B. K. Cantrell, K. L. Rubow

"Two source apportionment techniques have been applied by the Bureau of Mines to aerosol measurements in diesel equipped underground noncoal mines. The first technique is based on size selective sampling and the premise that the diesel exhaust fraction of the aerosol is predominately sub-micron in size while the mineral dust fraction of the aerosol is mostly super-micron in size. The second technique, Chemical Mass Balance (CMB) modeling, was used to referee the analysis of diesel and mineral dust aerosol concentrations with the size selective method.The size distribution data were modeled using a log-normal regression to parameterize the sub- and super-micron fractions of the sampled aerosol and to estimate the mineral and diesel contributions to each. For the mines visited, analysis of the size selective: samples yielded an average value for the fraction of the fine aerosol attributable.to mineral dust of 3 pct.'The CMB analysis, applied to both fractions of the respirable mine aerosol, yielded the amount contributed to each by the diesel· and dust aerosol sources. Less than 5 pct of the sub-microm fraction was mineral dust, however, as much as 20 pct of the diesel aerosol was found: ""in the super-micron fraction requiring a correction of the sub-micron fraction to account for the missing diesel mass. More accurate measurement will require a carbon specific analysis of the aerosol."

Jan 1, 1988

By Sean Gallagher, Rhys Llewellyn, Jay Mattos

This paper contains the results of an examination of accident, injury, employment, and production information reported to the U.S. Department of Labor&apos;s Mine Safety and Health Administration (MSHA) and provides information on some of the measures longwall mine operators are using to prevent accidents In all industries, technological advances play a key role in determining those who will survive as competitive participants in an increasingly global marketplace. While mining is among the most basic of industries, technological change is neither unfamiliar nor unwelcome to miners. Historically, technological advances in mining, particularly coal mining, have tracked closely with fluctuations in demand. In the early 1900&apos;s, coal accounted for more than three quarters of all the fuel consumed in the U.S. To meet this tremendous demand, underground cuffing machines were introduced, resulting in faster, more efficient coal extraction. Transporting coal to the surface, however, remained labor intensive. In the 1920&apos;s, nearly all underground coal was still being hand loaded. Demand for coal then declined as the price of oil, natural gas, and electricity became competitive. In the late 1930&apos;s and throughout the duration of World War II, coal demand and production was high. By 1940, more than half the coal mined was being mechanically conveyed to the surface. In 1948, the continuous mining method was introduced in the U.S., further accelerating the extraction process. By the 1950&apos;s and 1960&apos;s, however, coal production again declined as railroads converted to diesel fuel and gas and oil provided a larger share of the home heating market. Underground coal mines required even more mechanization to remain competitive as an energy source. The first longwall system was introduced in 1960. By 1995, longwalls were producing more than 189 million tons of clean coal annually, surpassing continuous mining production for the second straight year. The mining of coal and other materials has not come without a huge loss of life and considerable human suffering. More than 103,000 workers died from injuries in U.S. mines in the last 85 years. Between two and three thousand miners died each year from the turn of the century until 1931, many from underground fires and explosions. The U.S. has witnessed a tremendous drop in fatalities in underground coal mines. Credit for that is due to safety inspections and enforcement activities, better safety awareness and practices among management and labor, improved ventilation, the use of safer equipment, and increased mechanization which removed many miners from the hazards at the face and also reduced the size of the mining work force. There is little doubt that longwall mining has greatly increased underground coal mine productivity. The degree to which longwall mining has contributed to a safer work environment for underground miners is more difficult to ascertain.

Reduce the dust exposure of workers in large processing buildings at mineral processing operations, using a total mill ventilation system.

Jan 1, 1994

By F. N. Kissell, H. K. Sacks

This study examines the accuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines. The specific objective of this research was to find locations where an area sampler might work better than earlier studies have indicated. The results show that fixed-location area sampling cannot accurately predict the dust exposure of a machine operator, even when the best fixed location is sought, the fixed location is quite close to the operator and the bias due to the dust concentration gradient is corrected. Industrial hygienists have known for many years that area sampling is unsuitable for measuring air contaminant exposures in the workplace. Near contaminant sources, the dilution air and the contaminants are not evenly mixed. Therefore, when workers are near contaminant sources, exposure measurements must be taken from the worker&apos;s breathing zone to be accurate

By Andrew B. Cecala, Edward D. Thimons, George W. Klinowski

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 1993