Search Documents

By Peter F. Strong, Robert L. Lagace, Alfred G. Emslie

This paper is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1973

By Walter W. Fisher

Cement copper was flash roasted in a vertical tube furnace to convert the copper to acid-soluble oxides as part of a postulated process for refining cement copper by oxidation roasting, acid leaching, and electrowinning. The results of the study showed that the oxidation was a linear function of oxygen concentration between 0 and 20 percent, but above 20 percent oxygen there was no further increase in oxidation. Therefore, air was the optimum oxidizing atmosphere in this flash roasting system. The oxidation followed a parabolic rate law as the roasting temperature was increased from 400° to 800° C. Extrapolation of the data, based on the parabolic law, indicated that at 400°, 500°,600°,700°, and 800° C, the roasting times required for complete conversion to soluble oxides were 75, 37, 21, 7.7, and 4.6 seconds, respectively. Cyclic-roasting test results did not substantiate the predictions obtained through data extrapolation.

Jan 1, 1973

By Steve Iverson, Jeffrey C. Johnson, Henry Rodriguez, Rene Rodriguez, Michael Lhamond

To reduce fatalities resulting from personnel falling into voids formed above feeders in coal piles, the National Institute for Occupational Safety and Health at the Spokane Research Laboratory established a project to monitor coal surge piles to detect the formation of voids. A resistivity imaging method has been developed by GECOH Exploration, of Lexington, KY, in which a geophysical technique known as vertical electrical sounding (VES) is used to scan for these voids. VES operates by measuring the electrical field produced by a current in the ground at the bottom of the coal pile. This paper summarizes the results obtained from a field-scale test and shows that mapping voids within a coal pile is possible.

By John Durkin, Harry Dobroski

This paper presents a general overview of the Bureau of Mines' programs in the areas of operational and post-disaster communications. These programs encompass both hardware developments and system evaluations. Topics discussed include a new visual paging system compatible with existing pager phone lines, a means of modifying commercially avail able pager phones to permit selective paging and message leaving, a multiplexed telephone system that uses twisted shielded pair and requires no central control, medium frequency hardware developments, and a manual for mine communications. Research has continued in the area of post-disaster location and communications. This research is based on seismic and electro- magnetic techniques. Each has been extensively studied and field tested to better understand its ability to perform effectively. A brief description is given of the post-disaster program. Results are promising and provide insight into future areas of research.

By Maurice Deul, Herbert H. Fields, John H. Perry

The Bureau of Mines has been promoting health and safety in mining since its establishment in 1910. One area of research covers methane control in coalbeds; this report describes a multipurpose borehole used for both degasification and the production of commercial-quality gas. The multipurpose borehole was drilled into a barrier pillar, and seven horizontal degasification holes and one pressure point hole were drilled radially out from its perimeter. On January 28, 1974, after 505 days of degasification, a compressor was installed to the exhaust stack of the multipurpose borehole (2), and pipeline--quality gas was introduced into a commercial pipeline. As of February 4, 1975, over 171 million cubic feet of gas had been purchased by the gas company. The in situ pressure at a depth of 200 feet into the coalbed and the average gas flow and water flow from the degasification holes as they were completed and closed off were 203 psig, 1,200,000 cfd, and 6.8 gpm, respectively. Twenty-four hours after the seven holes were connected through individual pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psig. Five hundred days later, the corresponding values were 620,000 cfd, 0.15 gpm, and 10.5 psig. Daily flows have been as high as 800,000 cfd, and as low as 360,000 cfd, during the last 500 days. On February 4, 1975, after 882 days of degasification, 576 million cubic feet of gas had been removed from the Pittsburgh coalbed; apparently a much larger area of virgin coal is being degasified than is defined by the holes. This study indicates that horizontal boreholes drilled into a coalbed from the bottom of any shaft will effectively remove gas from the Pittsburgh coalbed.

Jan 1, 1975

By Erica E. Hall, Robert H. Peters, Charles Vaught, Jon C. Volkwein

Coal Workers Pneumoconiosis is the leading cause of death due to occupational illness among coal miners. This disease is caused by miners’ exposure to respirable coal mine dust. A Personal Dust Monitor has recently been developed to provide near real time feedback to miners regarding the number of milligrams of respirable coal mine dust in the air they breathe. This paper was prepared by the National Institute for Occupational Safety and Health to document coal miners’ reactions to this new device, and how they make use of the information it provides. Structured interviews were conducted with 30 coal miners at four mines. A four-stage conceptual model of miners’ decision processes with respect to how they interpret and respond to the dust exposure numbers from their personal dust monitor is proposed. The stages are: Diagnosis, Action Planning and Intervention, Evaluation, and Institutionalization. The interview responses provide considerable support for the model. Most miners paid attention to Personal Dust Monitor feedback and made efforts to reduce their dust exposure. Their efforts included: changing where they positioned themselves, making ventilation system improvements, and using respirators more often. The 29 miners who reported having experience wearing both the old and new type of dust monitors were asked which dust sampling system they preferred. Eighteen (62%) preferred the new monitors, 7 (24%) preferred existing monitors, and 4 (14%) had no preference. The most frequently cited advantage of the new monitor is its ability to provide relatively quick feedback on dust exposure. Miners provided several suggestions for improving the design of the instrument.

Develop a down-hole replaceable diamond core bit that will reduce overall drilling costs and increase total available drilling time per hole. Approach A one-piece diamond core drill bit of unique geometric shape has been designed, fabricated and field tested. The bit can be withdrawn (or replaced) from the bottom of the well-bore without removing the drill rods from the hole, saving a significant amount of non-productive drilling time. How It Works The replaceable bit system consists of two basic subsystems: the removable core bit, and the equipment necessary to replace the wornout bit without pulling the drill rods out of the hole. The geometric configuration of the bit is that of a one-piece diamond studded cutting element created by "slicing off" two parallel sides of a conventional diamond cone bit. This geometric configuration, along with some minor modifications to the outer core barrel, allows the bit to be rotated in two planes and, with the retraction-insertion tools, raised or lowered through the interior of the drill rods using a conventional wire-line system. For example, to retrieve the bit, a retraction tool is lowered through the drill rods using a conventional wire-line system and at the hole bottom, the tool automatically orients itself within the outer core barrel.

Jan 1, 1981

By E. Morrice

Gadolinium, dysprosium, and yttrium are difficult to electrowin as high-purity liquid metals because of their high melting points (>1,300° C). Samarium metal is difficult to prepare directly by electrolysis because the metal reacts with the electrolyte. In this Bureau of Mines study, the rare-earth metal was electrodeposited on a solid manganese, chromium, or iron cathode to form a low-melting alloy. The alloy was then vacuum distilled to separate the rare-earth metal from the ferrous metal. A typical samarium metal product, obtained as the distillate from vacuum distillation of a samarium-iron alloy, contained 150 ppm oxygen, 80 ppm carbon, and 50 ppm iron as impurities, Gadolinium metal, obtained as a residue from the distillation of a gadolinium-chromium alloy, contained 300 ppm oxygen, 200 ppm carbon, and 100 ppm chromium.

Jan 1, 1969

Provide the mining industry with an easy-to-use means of accurately predicting surface subsidence caused by longwall mining in the northern Appalachian Coal Basin. Approach The Bureau of Mines developed a subsidence prediction model using the novel approach of a variable subsidence coefficient. This approach had to be used because of the resistant strata types which commonly occur within the relatively thin overburden material typical in northern Appalachia. Such resistant strata precluded the use of the popular European methods that assume homogeneous overburden or overburden behaving as homogeneous from a subsidence point of view. The model is available in a BASIC computer program for use on most personal computers. The user has the options of obtaining individual subsidence calculations or may choose to develop a subsidence profile using an average overburden value. The program output can be generated in graphic or tabular form showing the location of the surface point with respect to the longwall panel edge, overburden depth, and the subsidence value.

Jan 1, 1986

By Charles L. Kimbell

This study is intended to serve three roles. First, it is the second annual edition of this study in a separate volume that represents a global overview and summary to supplement and complement the five regional volumes that now constitute the U.S. Bureau of Mines international, geographically arranged studies. In this regard, it also extends previous works under this title that appeared in the inter-national volume of the Minerals Year-book from the inception of that volume (the 1963 edition) until it was subdivided into six separate volumes in 1989. Following the traditional format of past chapters under this title, the basic statistical presentations herein deal chiefly with 1990, and in a few instances with 1988 or 1989; these latter two only because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting on the world's mineral industry that have occurred between the end of 1990 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

By George S. Koch

In preparing diamond-drill core samples for assay at the Homestake mine, Lead, S. Dak., 5-foot intervals of core are processed through three stages, crushing, grinding, and pulverizing, and portions of the core material are discarded after splitting at each stage of preparation. Then two 1-assay-ton fractions are taken from the pulverized material and assayed. This report investigates alternative methods of sample preparation. The consequences of crushing, grinding, and pulverizing all rather than part of the core are appraised through the statistical analysis of assay results from 118 5-foot intervals of core. Evidently, a substantial improvement in precision at small additional expense is obtained by grinding most or all of the core before splitting. Pulverizing all of the core would be desirable only if doing-so would cost less than assaying five random splits from each interval. Graphs and tables detail appropriate procedures to obtain specified precisions. The experimental design and methods can be applied to similar problems in preparing core and other geological samples.

Jan 1, 1972

This pamphlet and the enclosed video describe a safe, effective and economical method for removing dust from work clothes. Background Information Dusty work clothes can increase a worker’s exposure to respirable dust. Respirable dust is usually considered to be particles having an aerodynamic diameter of 10 microns or less and able to enter and deposit in the gas-exchange region of the human lung. A former U.S. Bureau of Mines report documented a 10-fold increase in worker dust exposure on a number of separate occasions from dusty work clothes.* It was found that once clothes become contaminated, they are a continual dust source until cleaned. The only MSHA approved method to clean work clothes requires a HEPA-filter vacuuming system which is very time consuming and difficult to perform effectively. Therefore, most workers use a single air hose (not MSHA approved) which can elevate dust levels for the worker, co-workers, and the work environment. A substantial amount of engineering technology has been developed that, when applied, can significantly lower respirable dust exposures of workers at mineral processing plants. But even with these improvements, some workers continue to exceed their permissible exposure limit. Elevated exposures increase the potential for developing debilitating or fatal lung diseases. ?e clothes cleaning method described within is an example of a continuing effort to reduce the potential for developing these lung diseases. Information about engineering research by the former U.S. Bureau of Mines and NIOSH can be found online at www.cdc.gov/niosh. ?is website can also be used for obtaining NIOSH information about health hazards associated with crystalline silica.

By Donald P. Tuchman, Robert P. Vinson, Linda J. McWilliams, Steven E. Mischler, Jon C. Volkwein

A personal dust monitor (PDM) was developed to measure respirable coal mine dust mass to provide accurate exposure data at the end of a work shift. Additionally, the new monitor continuously displays near-real-time dust exposure data during the shift. The PDM uses a tapered-element oscillating microbalance to measure the mass of dust deposited on a filter and continually displays the cumulative exposure concentration data. The accuracy and precision of the instrument was determined by comparison to gravimetric filter samplers in the laboratory and in four mines. Laboratory results with different coal types and size distributions showed that there is a 95% confidence that the individual PDM measurements were within ±25% of the reference measurements. Mine test results indicate that data taken with adjacent PDM and reference samplers are indistinguishable. The technology proved durable enough to successfully measure 108 shifts of data out of 115 attempts in the mines. Under these specific test conditions, the PDM demonstrated that it was convenient to wear, robust, provided accurate data, provided timely data that could be used to prevent overexposure, and was easy to use.

Jan 1, 2004

Introduction The Coal Mine Roof Rating (CMRR) is a roof classification system. It was first introduced to the mining community in 1994.The CMRR filled a longstanding need to quantify geologic description of coal measure rocks into an engineering value that could be used for mine design. It has now been written to a user-friendly visual basic code that can be run on any PC with a Windows operating system. Background Rocks that form the roof of coal mines can vary widely and quickly in composition, extent, and defects. This results in an equally broad range of rock properties that can substantially affect the ability of the rock mass to form a stable mine roof. The CMRR was designed to evaluate the properties of the coal mine roof rock mass that contribute to its weakness and convert them into a relative strength rating from 0 to 100. These properties include the cohesion and frequency of discontinuities like bedding, slips, shears, and joints; uniaxial compressive strength (UCS); and moisture sensitivity. With simple lab and field tests and observation, the CMRR can be calculated by technical and operating personnel with a minimum of training. The CMRR has been widely accepted in both U.S. and international coalfields. As a result, a number of roof control applications have been found for the CMRR. It is currently used as an input component in the Analysis of Longwall Pillar Stability(ALPS) program, which is used to design longwall chain pillars. Incan be used as a criterion for determining the appropriate width of mine entries. It has also been used to indicate the appropriate length of cut in weak ground. The CMRR can be used as a strength parameter to characterize inter burden between mined seams in the numerical modeling of subsidence effects. In any area where an estimation of coal measure rock mass strength is required, the CMRR can be adapted to fill this need. How It Works Originally designed to be used with underground exposures, the CMRR can also be calculated from core. The chisel test for bedding cohesion and the ballpeen hammer test for UCS are inappropriate for core. These tests have been replaced by point load testing both axially and diametrally. Two other measures that are common to standard core logging—Rock Quality Designation (RQD) and fracture spacing—are also used to estimate rock weakness. With these easily obtained parameters, the CMRR can be calculated from core and used in the mine planning and exploration phase. The input screens allow calculation of the CMRR for both underground exposure and core. The CMRR is reported both as a “dry" value and as a groundwater-adjusted value for moisture-sensitive rocks. There is a graphical output report featuring a lithologic column with annotated unit ratings and a roof bolt symbol representing the height of the bolted horizon. Another important feature is an AutoCAD interface. This feature allows the export of located CMRR data directly to an AutoCAD layer in XYZ form. In this way, drill hole data can be inserted directly to a base map.

Apr 1, 2003

By Richard V. Ageton

"Everyone admits that there are more accidents in metal mines than there should be but there is much difference of opinion as to the causes of accidents, whether avoidable or unavoidable, and the amount of responsibility attaching to the miner and the mine operator, respectively. However, it seems that one of the main reasons why there are so many accidents, is that there is so little general knowledge regarding their causes and costs. Some information regarding the costs and causes of metal-mine accidents is presented in this paper.The data contained were obtained from a study of the complete accident and medical reports of two large metal-mining companies, which carry their own insurance. Path maintain hospitals with competent medical attendants. One of these companies also maintains a very efficient safety bureau, consisting of a safety engineer, with two assistants who work in connection with the medical department, and with the safety committee made up from among the miners themselves.Daring the year of 1920, ""A"" Company employed approximately 900 men, and these men worked more than 270,000 shifts. There were 373 minor and major injuries, among these 900 men, hence assuming that each injured man was hurt cut once, 41 per cent of the men who worked in this mine received some kind of time-losing injury during the year. On account of these injuries the injured men lost 3731 shifts, and thus the time lost due to injuries amounted to approximately 1.4 per cent of the total number of shifts worked,"

Oct 1, 1923

By G. L. Oldright, John D. Sullivan

"The present article is the second of a series of papers dealing with the dissolution of copper minerals in various reagents. Work done on the problem has been carried out at the Southwest Experiment Station of the United States Bureau of Mines, in cooperation with the Department of Mining and Metallurgy, University of Arizona. The first paper4 dealt with the dissolution of azurite, malachite, chrysocolla, and tenorite. Preceding articles5 have also dealt with other factors involved in the leaching of copper ores.Cuprite (Cu20) is usually considered as a mineral which is not adaptable to sulphuric acid leaching. Hofman,6 in describing leaching by sulphuric acid, states: ""Cuprite is decomposed into CuO and Cu; and ore carrying cuprite has to be oxidized (weathering, roasting) before treatment."" Greenawalt7 says: ""When acted upon by dilute sulphuric acid, it is partly reduced to metallic copper and partly oxidized into copper sulphate. When heated with strong acid it is entirely oxidized to sulphate."" Work to be described in this article was undertaken to ascertain the conditions whereby all the copper in cuprite could be converted into the soluble sulphate."

Dec 1, 1929

By W. P. Yant, R. R. Sayers, G. W. Jones

In the treatment of any illness the early diagnosis is of very great importance . This is especially true in cases of carbon monoxide poisoning , whether acute or sub-acute in character. A diagnosis of CO poisoning is usually made from a correlation of the history , the possible place of exposure , and the symptoms produced . This , however, is not positive evidence because CO often is present in unsuspected places and can be absent in suspected places . Also , the symptoms of this type of poisoning are common to other causes . In many such cases the correct diagnosis may be very difficult , if not impossible by this method and as a result little or no treatment is given . Sub- acute cases , those in which the subject is exposed to concentration sufficient to cause only headaches , malaise , feeling of weakness and dizziness , may be incorrectly diagnosed and as a result , improperly treated . Probably the best method of diagnosis is by examination of the subject's blood . Many methods for the detection of CO in the blood have been developed , but owing to their various individual disadvantages have never come into common usage . Some of the quantitative methods are satisfactory with regard to accuracy but require elaborate and expensive apparatus , special technique and training, or are too delicate and cumbersome for field use . It is of vital importance in all industrial and domestic accidents occuring at places where CO might be suspected or where the symptoms are typical of CO poisoning that a qualitative and preferably a quantitative determination be made the extent of poisoning being of importance in deciding whether CO was the direct or contributary cause) to show the presence or absence of 0. This is indeed essential from a medical standpoint as it aids in prescribing treatment and from a legal standpoint to insure justice in the claims that are often unjustly decided for want of positive evidence.

Jun 1, 1923

To develop an explosive charge that will effectively break rock in underground mines and that can be safely fired without the use of blast-holes or the need for stemming. Approach The Bureau of Mines developed a non-incendive, cylindrically-shaped explosive charge that will not ignite gassy or dusty atmospheres, even methane-laden air. How It Works Firing unconfined explosive charges in underground mines is prohibited by law since detonation in gassy or dusty atmospheres is extremely dangerous. However, there are advantages in using unconfined charges from both a safety and a production standpoint. Explosives can effectively break up large boulders, rocks and slabs when leveling roof falls and can dislodge overhangs which miners would other-wise have to dislodge manually, exposing themselves to

Jan 1, 1983

Improve the safety and comfort of operators of large mining equipment. Approach Develop an improved driver restraint system that is easy to use, reliable, and cost-effective, while providing increased protection in the event of a collision or rollover. The Novel Restraint System There are several problems associated with conventional lap-belt type restraint systems. Among these are: restriction of movement, lack of comfort, and fear of entrapment. Standard seatbelts become dirty and oily from lying on the vehicle cab floor and can ruin a driver's clothes. Some haulage equipment may not even have seatbelts available to drivers since they are sometimes removed during maintenance activities or as a result of vandalism. Recognizing a need to address such problems by providing a more acceptable means of driver restraint, the Bureau of Mines designed and fabricated a novel vest-type restraint system. The vest is designed to be worn during a driver's 8-hour shift and would be issued much like safety glasses, hard hats and safety shoes, thus becoming part of the operator's individual protective equipment and assuring that each vehicle has a restraint system when in operation. The vest-

Jan 1, 1985

By Maria I. De Rosa

Table 1 and figure 1 show the number of fires and fire injuries that occurred in underground metal/nonmetal and stone mines by state during 1990-2001. Table 1 also shows the injury risk rates, employees' working hours, and lost workdays. Overall, 65 fires occurred in 20 states; these include 2 fires and no injuries for contractors. Six of the fires caused nine injuries. The yearly average was 5.4 fires and 0.75 injury. Forty-one fires with 2 injuries occurred in metal mines, 14 fires with 7 injuries occurred in nonmetal mines, and 10 fires with no injuries occurred in stone mines. The underground mine fires required 25 mine rescue team interventions and 30 mine/section evacuations. The Ewhr value was 260 x 10° hr (Irr = 0.007), and the LWD value was 83. Idaho had the most fires (eight fires and no injuries), followed by Louisiana (seven fires and two injuries), Michigan (six fires and six injuries), and Missouri (six fires and no injuries). Of these states, Michigan had the highest injury risk rate value (Irr = 0.146). Table 2, partly illustrated in figure 2, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires during the six time periods show an increase during the fourth period followed by a sharp decrease during the fifth period and a sharp increase in the last period. The number of fire injuries show an increase followed by a decrease during most of the periods, accompanied by a decline in employees' working hours during most of the periods; an increase is seen during the third and fourth periods. The In values follow patterns similar to those shown by the injury values. Tables 3-8 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 3 shows the major variables related to fires for 1990-2001. Table 9 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004